Ak 500 fue 1 инструкция

Cпецификация

• IP 54, 3-фазный, 400 В, размер (Ш x В x Г) = 230 x 460 x 200 мм, преобразователь частоты, электронное регулирование конечных положений, пленочный выключатель «Откр./Стоп/Закр.», главный выключатель, клавиша аварийного отключения, автоматическое закрывание и индикация на дисплее, соединительный кабель с вилкой СЕЕ.
  Готовая к подключению проводка блока управления с цветной кодировкой для простого и быстрого подключения устройств безопасности и компонентов принадлежностей.
  Области применения: логистика, складские помещения, мелкие предприятия

Техническая спецификация

• Уникальная ссылка3245

• Тип продукцииControls

• Группа продукцииFrequency converter controls

• Дата публикации2021-08-19

• Номер версии1

Связанные

• Разработано вГермания

• Страна-производительГермания

Классификация

• Категория BIMobjectЭлектричество — Controls

24 VAC or VDC White: 0 V Relay Green: common Yellow: normally open Black: normally closed Antenna 1 Move the door so that the bottom bar is approx. 48 in (121.9 cm) from the floor and press the e-stop on the control panel 2 Remove the lid from the transmitter 3 Remove the paper from the battery in the transmitter 4 Press and hold the programming button on the receiver until the receiver LED begins flashing slowly. Once it begins flashing release the programming button 5 Activate the reversing edge with your hand (the transmitter LED will come on once. The receiver LED will flash quickly 8 times then stop). 6 The receiver LED will begin flashing slowly again. When it does, press and hold the programming button until the receiver LED flashes quickly. Remove your finger from the programming button before the receiver LED stops flashing 7 The receiver LED will now be off. If it is still on that means the programming button was not released prior to the receiver LED finished flashing. Return to step 4 8 Activate the reversing edge with your hand while the door is closing. The transmitter and receiver LEDs should both come on once and the door should reverse. Receiver LED Idle — waiting for signal from transmitter to reverse door Off Waiting for signal from transmitter to sync transmitter and receiver Slow flashing during programming Relay in receiver is being programmed Quick flashing during programming Received as signal from the transmitter to reverse door Flashes once during normal operation Battery is low — change the battery Slow flashing during normal operation Transmitter LED Idle — waiting for activation of reversing edge Off Flashes once Received an activation from the reversing edge. Sending a signal to the receiver Flashes twice or three times Received an activation from the reversing edge. Sending a signal to the receiver but with reduced batter power. Replace battery 47 AS500FUE-1 / TNR / 07.2019

9 Programming Monitored Edge 9.1 Programming sequence 1. Press PROG button on the receiver until R1 LED lights 2. Press PROG button on the transmitter 3. A beep will be heard on the receiver indicating the transmitter is properly programmed 4. To exit programming mode, wait 10 sec or press PROG button the reciever. Two beeps will be heard. 9.2 Reset sequence 1. Press PROG button on the receiver until the R1 LED lights on 2. The receiver will emit 10 warning sound signals, 3. and then at a faster frequency, indicating that the operation has been carried out 4. To exit programming mode, wait 10 sec or press PROG button on the receiver. Two beeps will be heard Receiver and transmitter LED’s Receiver Transmitter Edge activated Receiver is being activated by another transmitter Flashing Light represents edge is not connected, the transmitter receiver is not programmed, or the DIP switches are incorrect Low battery or loss of communication Receiver is in the wrong mode and waiting for a test signal Signal is being disrupted Receiver memory is full Change in operating mode of receiver with current programmed transmitters AS500FUE-1 / TNR / 07.2019 48