Allen bradley 1336 plus инструкция на русском

• 1, Instructions This publication will guide you through installation (or replacement) of the 1336 PLUS Language Module. 1. Check the version of firmware presently installed in the drive. If the current version is 1.04 or greater, proceed to step 2. If you have version 1.03, parameters 111-127 and 180 must be checked. The value of each parameter must be greater than zero and less than 212. If any value is outside of this range, reprogram using the Program mode before proceeding to step 2. …

• 2, 2 1336 PLUS Language Module Installation/Replacement 3. Using the figure above, locate the Language Module for your drive and note orientation. On 0.37-3.7 kW (0.5 — 5 HP) drives, the HIM and cradle must be removed before proceeding. A. To remove the HIM, slide it down and out of its cradle. B. Remove the cradle by taking the 4 corner screws out. Position the cradle and attached cable out of the …

• 3, 1336 PLUS Language Module Installation/Replacement 3 4. Remove the module by squeezing the sides- in, and pulling outward. Discard module. 5. Position the new Language Module on the Main Control Board, using the silk screen outline on the board as a guide. 6. Carefully align the module connector with the Main Control Board connector. Firmly press the module onto the Main Control Board until fully seated. The module will “snap” (lock) in…

• 4, Rockwell Automation 1336 PLUS Publication 1336 PLUS-5.5 – May, 1996 P/N 74001-007-01 (C) Supersedes June, 1994 Copyright 1996 Rockwell International Corporation. All rights reserved. Printed in USA.
  …

Скачать

• 1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit 3 Replace Ribbon Cable (1336F-AE4 Only) Figure 1 1336S/F-AA2 & AA3 Enclosure Kits Figure 2 1336S/F-AE2 & AE3 EMC Enclosure Kits Figure 3 1336S/F/T-AA4 & AA5 Enclosure Kits Figure 4 1336S/F/T-AE4 & -AE5 EMC Enclosure Kits
  

• 2 1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit Installation Access to the top, bottom and sides of the drive chassis is required to assemble the kit. If the open chassis drive is already installed, remove and lock-out all power to the drive, then label and disconnect all wiring. External wiring will have to be rerouted through enclosure knockouts once the kit has been installed. Figure 1 Enclosure Kits – 1336S/F-AA2 and -AA3 1. Moun

• 4 1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit Door Grounding Jumper Jumper must be Installed inside Enclosure between Enclosure Door (Grounding Stud) and Chassis Grounding Stud. Figure 5 Enclosure Kits – 1336S/F/T-AA6 and -AA7 EMC Enclosure Kits – 1336S/F/T-AE6 and -AE7 For CE conformance, the EMI gasket (pre-installed) and jumper (see below) supplied with the 1336S/F/T-AE6 & AE7 must be in place. 1. Slide the side plates over the chassis tabs as shown. 2. Attach the top and bottom plates to the side plates by sliding

• Instructions This publication will guide you through installation of an IP 20 (NEMA Type 1) Enclosure Kit (1336S/F/T-AAx) or EMC Enclosure Kit (1336S/F/T-AEx). Refer to the appropriate drive User Manual for further information. Enclosure Installation ! ATTENTION: This drive contains ESD (Electrostatic Dis- charge) sensitive parts and assemblies. Static control pre- cautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures ar