Bajaj pulsar ns 200 инструкция

• Contents

• Table of Contents

• Bookmarks

Summary of Contents for Bajaj PULSAR NS200

This manual is also suitable for:

As 200Pulsar ns 200Pulsar as 200

• Location of Parts (Pulsar NS 200) Front Fork Clutch Lever Fuel Tank Cap Manual Choke Lever Pillion Foot Rest Side Stand Gear Change Lever Digital Speedometer Disc Brake LED Tail Lamp 5 OFF ON
  

• MAX. MIN. Location of Parts (Pulsar AS 200) Grab Handle Pillion Seat Rider Seat Rear Disc Brake Radiator Coolant Level Indicator Coolant Tank Cap Rear Brake Pedal Paper oil Filter Front Brake Lever Rear Number Plate 7 Nitrox Rear Shock Absorber
  

• Removal of Side Cover LH or RH • Remove pillion & rider seat. • Remove screw (A) upper & (B) lower of side cover mounting. • Pull front portion of ‘Side Cover’ to release its lug from hole (C) provided on ‘Fuel Tank’. • Pull rear portion of ‘Side Cover’ to release its Lug (E) from hole (F) provided on ‘Chassis’. CAUTION : Remove cover as described above, Otherwise the lugs may break. Fitment of Side

• Wheels — Tube Less Tyre CAUTION : Tubeless tyres are fitted in this motorcycle. The walls of the tyres in contact with the wheel rim should not be damaged in any way during fitment / removal of tyre. The tyre side walls in contact with wheel rim seals air. Wheel Puncture : • Visit nearest known tubeless tyre repair shop to remove puncture. • Remove puncture by Filler or Plug method only. • Do not use patch method to

• How to Ride Your Bike 1. Starting The Engine : • Turn the fuel tap knob to ‘ ’ or ‘ ’ position. • Turn ignition switch key to ‘ ’ position. • Keep kill switch in ‘ ’ position. • Confirm that transmission is in neutral / press the clutch lever. • If the engine is cold or when starting for first time, use manual choke ( ) for quick starting. Choke lever is located on LH side of carburettor. • Keep throttle completel

• 2 7 8 10 3 4 6 5 9 1 M S Speedometer Details Speedometer display will work when, only both Ignition switch & kill switch are in ‘ON’ position. 1. Fuel Level Indicator: It shows fuel level in fuel tank. 2. Tachometer Dial: It shows engine speed in RPM. 3. Turn Signal Indicator (LH & RH): When Turn signal switch is turned to Left or Right, Turn pilot Indicator — LH or RH will flash. 4

• Fitment of Front & Rear Seat Fitment of ‘Front Seat’ • Match the lugs of ‘Front seat’ (A) with chassis bracket (B). • Push ‘Front seat’ toward petrol tank. • Match ‘Front seat’ rear brackets (C) with the holes provided on chassis. • Tighten the bolts (D). Fitment of ‘Rear Seat’ • First make sure ‘Front seat’ is fitted properly. • Place ‘Rear seat’ in fitment location. • Insert bracket (E) of seat into hook (F). • Match the rod of

• Front Seat / Battery Battery • It is located below ‘Front seat’. Battery details are given in ‘Battery Maintenance’ page no. 28. Removal of Front Seat • First remove ‘Rear seat’. • Remove ‘Front seat’ mounting bolts (B). • Pull back rear end of ‘Front seat’. • Take out ‘Front seat’. B 17
  

• Steering cum Ignition Lock To Lock the Steering : To lock the steering, turn the handle bar to the left side. Push & release the key. Turn the key to “LOCK” position and remove the key. Steering lock can be done on left side only. To Unlock the Steering : To unlock steering, insert the key in steering cum ignition lock & turn it clockwise to

• Periodic Maintenance & Lubrication Chart 36 500 ~ 750 4500 ~ 5000 9500 ~ 10000 14500 ~ 15000 19500 ~ 20000 24500 ~ 25000 29500 ~ 30000 RECOMMENDED FREQUENCY Servicing Sr. No. Operation 1st 2nd 3rd 4th 5th 6th 7th Kms Remarks Radiator fins * It is strongly recommended to use specified grade only , In case of any other engine oil of same specifications is used the frequency would be every 5000 kms ** As applicable to mo

• Daily Safety Checks • Brake Fluid level above MIN mark provided on reservior, applicable to disc brake vehicle. • Drive Chain slack of 15 to 25 mm adequately lubricated. • Function of all lights & horn • Clutch lever play — 2 to 3 mm • Check Coolant level between MIN and MAX mark in coolant reservoir tank. • Smooth steering movement without restriction. • Side stand return to its retracted position. • Correct inflation pressure in both tyres Adequate tyre

• Periodic Maintenance Information Drive chain must be cleaned & lubricated as per periodic maintenance schedule. Drive Chain (O-ring type) • ‘O’ rings must always be kept wet for best performance hence lubricate every 500 Km. • O-ring chain lubrication can easily be done by owners using Bajaj ‘Chain Lube Spray Can’ available with Bajaj dealers,

• Engine Cooling System • Coolant is provided for cooling of engine. • Water pump (A) in the engine circulates the coolant in cooling system. • The pressure resulting from the heating of the cooling system is regulated by a valve in radiator cap (B). • Heat expansion causes excess coolant to flow into compensating coolant tank (C). • When the temperature falls,