Basic charger 2 d48 50 инструкция

Зарядное 12 вольт

Зарядное 24 вольта

Зарядное 48 вольт

Зарядное 80 вольт

PBM зарядные устройства

Зарядные устройства POWERGEN

Зарядные устройства SPE

ENERGIC PLUS

Разрядные устройства -тестеры

ATIB ELETTRONICA зарядные устройства

Зарядные устройства для штабелеров

EKT (EFFIC)

• Box Contents See the table below for differences in the box content of three models. Figure 1-2 Box conten ts Table 1-1 Accessories in the box Item Description QTY Remark 1 Basic Charger-32A (BC3) 1 Charging Plug Input Power Cord OLED Display RFID Icon Smart Charger -32A (SC3) Charging Plug Input Power Cord OLED Display RFID Icon Intelligent Charger-32A (IC3) Charging Plug Input Power Cord OLED Display RFID Icon 2 Mounting Bracket 1 Attached to the back of the charge point 3 Holster ASSY 1 With Hook x1, Holst

• 2. Mount charge point onto mounting bracket and lock the screw. 2-1. Put the charge point on the mounting bracket. 2-2. Fix the charge point on mounting bracket by M4 screw and screw washer. 2-3. Please refer to the following torque. Screw Torque M4 16 kgf.cm 13.88 lb/in Figure 2-6 Charge point and mounting bracket Figure 2-7 Tighten M4 screw 9 Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0 BlinkCharging.com • (888) 998.2546 ©2021 Blink Charging Co. • NASDAQ: BLNK
  

• 2.6 Install the Holster 1. Separate the holster from hook. Figure 2-14 Separate the holster 2. Fasten the hook on the wall with appropriate screws. 2-1. For finished walls supported by wood studs, use #12 tapping screws (x2). 2-2. The recommend torque is 25 kgf.cm (21.7 lb-in). Figure 2-15 Secure the hook 15 Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0 BlinkCharging.com • (888) 998.2546 ©2021 Blink Charging Co. • NASDAQ: BLNK
  

• 1 Contents 1 Introduction …………………………………………………………………………………………………………….. 2 Product View ………………………………………………………………………………………………… 2 2 Installation……………………………………………………………………………………………………………….. 4 Before Installation ………………………………………………………………………..

• SAVE THESE INSTRUCTIONS WARNING: RISK OF ELECTRIC SHOCK Do not remove the cover or attempt to open the enclosure. No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: RISK OF ELECTRIC SHOCK • Do not touch live electrical parts. • Incorrect connections may cause electric shock. • Do not Disconnect Under Load. WARNING: This equipment is intended only for charging vehicles that do not require ventilation during charging. Please refer to your

• 2.4 Install the Charge Point 1. Secure the main body mounting bracket to the wall with appropriate screw. Follow applicable accessibility requirements for the mounting position. The unit shall be stored or located at a sufficient height. For indoor use: The unit shall be mounted at a sufficient height from the floor between 18 inches (450 mm) and 4 feet (1.2m). For outdoor use, it is not lower than 24 inches (

• 3-7. Secure the conduit on the enclosure. Please refer to the following torque. Conduit Torque 1 “ 35 kgf.cm 30.36 lb-in 3-8. Reassemble top cover. Please refer to the following torque. Screw Torque M4 16 kgf.cm 13.88 lb-in 14 Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0 BlinkCharging.com • (888) 998.2546 ©2021 Blink Charging Co. • NASDAQ: BLNK
  

• Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0 BlinkCharging.com • (888) 998.2546 ©2021 Blink Charging Co. • NASDAQ: BLNK I IMPORTANT SAFETY INSTRUCTIONS This document contains instructions and warnings that must be followed when installing and using the Electric Vehicle Supply Equipment (EVSE). Before installing or using the EVSE, read this entire document as well as WARNING and CAUTION markings in this document. Safety Instructions The symbols used have the following mean

• 1 Introduction This user manual applies to “32A Level 2 AC Charger for Plug-in Electric Vehicles (PEVs) and Battery Electric Vehicles (BEVs)”. The Level 2 Electric Vehicle Supply Equipment (EVSE) with 32A capabilities will be used in North America. It can provide a shorter charging time than the traditional 16A EVSE. !!! Any unauthorized modifications will void the manufacturer’s warranty. !!! 1.1 Product View Different models of Charger: Basic Charger-32A (BC3) Smart Charger-32A (SC3) Intelligent Charger-32A (IC

• Figure 2- 13 Input wiring Model Current Rating Intelligent Charger-32A 32 A CAUTION: To reduce the risk of fire, connect only to a circuit provided with 40 amperes maximum branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part I, C22.1. CAUTION: If this unit is installed outdoors, the outlet must be ra

• 2 Installation 2.1 Before Installation 2.1.1 Safety check • Check for transport damages. • Before connecting the product to the power supply, check that the power supply voltage and current rating corresponds with the power supply details shown on the product rating label. The charge point must be installed only by a licensed electrician in accordance with the provisions of the local electrical industry construction and should comply with national

• B. For finished walls supported by wood studs, use 1/4”or M6 tapping screws. ( Commercially availab le ) C. Please refer to the following torque. The actual torque is according to the wall material. Screw Torque M6 25 kgf.cm min 21.7 lb-in min #12 25 kgf.cm min 21.7 lb-in min 8 Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0 BlinkCharging.com • (888) 998.2546 ©2021 Blink Charging Co. • NASDAQ: BLNK
  

• 3-2. Use Philips screwdriver to release terminal screws. 3-3. Fold the wire end to pass through the conduit and insert them into the input hole. 3-4. Fix the copper wire on the corresponding terminal block. The wiring instruction is printed in front of the terminal block (L1/L2/G). 3-5. Use the following torque to connect the wire terminal to the terminal block. Screw Torque M4 16 kgf.cm 13.88 lb-in 3-6. The recommended terminal specifications are as following. Figure 2- 12 Input wiri

• 2. Find SIM card socket Figure 2-2 Position of SIM card socket 3. Insert SIM card Figure 2-3 SIM card socket and cover Open/Lock direction 3-1. Push down the cover to open SIM card socket. 3-2. Prepare the SIM card. (Use micro-SIM, 15mm x 12mm.) 3-3. Insert the SIM card. 3-4. Close the SIM card socket and push the cover toward lock direction to lock the cover. 3-5. Reassemble the top cover. Please refer to the following torque. SIM card installation is completed. Screw Tor

• Repair and Ma intenance Clause  Only licensed electricians can repair or maintain the charge point. It is forbidden for general users to repair or maintain it.  Turn off input power before repair or maintenance the charge point. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

• 2.5 Input cord connection (for IC3 only) 1. Choose the appropriate conduit in accordance with all applicable state, local and national electrical codes and standards. Figure 2-9 Conduit. Figure 2-10 Right angle conduit 2. Clamp copper terminal to connect copper wire. The clamp point is covered by heat shrink tube for protecting. 2-1 Refer to following wire specification. Use conductor type other than RHH, RHW and RHW- 2 with outer covering. Model Terminal Conductor Rating Intelligent Charger-32A L1, L2, G 8 AWG 90C copper wire Figure 2-11 Copper te