Car alarm system l5000 инструкция на русском

LYNX Touch Security System

Programming Guide

ARMED

READY

800-06895V1

8/11 Rev. A

Table of Contents

Entering Programming Mode ………………………………………………………………………………………………………………….. 3 Programming the Data Fields………………………………………………………………………………………………………………….. 3 Loading a Default Set …………………………………………………………………………………………………………………………….. 3 Exiting Programming Mode …………………………………………………………………………………………………………………….. 3 Data Fields …………………………………………………………………………………………………………………………………………… 4 Change Installer Code…………………………………………………………………………………………………………………………. 4 Program System Type…………………………………………………………………………………………………………………………. 4 Program Date and Time………………………………………………………………………………………………………………………. 4 Program Communications …………………………………………………………………………………………………………………… 6 Program Zones ………………………………………………………………………………………………………………………………….. 7 Program Keys…………………………………………………………………………………………………………………………………….. 8 Program Reporter ………………………………………………………………………………………………………………………………. 9 Program Sounder ……………………………………………………………………………………………………………………………… 13 Program System Settings ………………………………………………………………………………………………………………….. 13 Zone Programming Worksheet ……………………………………………………………………………………………………………… 16 Explanation of Zone Assignment Table Headings …………………………………………………………………………………. 18 5800 Series Transmitter Loop Numbers Diagram…………………………………………………………………………………….. 19 Programming Default Tables…………………………………………………………………………………………………………………. 20 LYNX Touch Summary of Connections Diagram ……………………………………………………………………………………… 23

Refer to the LYNX Touch Series Installation and Setup Guide P/N 800-06834 or later for detailed information on programming the system. The Installation and Setup Guide contains full descriptions for all data fields.

UL

LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-SHA) is installed.

Entering Programming Mode

You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly hear feedback announcements or system beeps.

1. Power up the LYNX Touch control, when the Home Screen appears, select “More”.

2. 3. 4. Select “Tools”. The system displays a virtual keypad.

Enter: Installer Code (4 + 1 + 1 + 2).

The System Programming Screen is displayed. Select “Program”. The ARMED and READY LEDs will flash and the following options will be displayed:

Installer Code Date Time Zones Keys Sounder Default Config.

5.

System Type Communications Comm. Diagnostics Reporter System Settings

Use the down ! arrow to scroll to the next page of options.

Select an option to advance to that Programming screen.

Notes: 1. If a different Installer Code has been programmed, enter: the New Installer Code. 2. If the control was previously programmed to inhibit re-entry by the Installer, power down the unit (remove AC and battery power) and enter Program Mode within 30 seconds of powering up.

Programming the Data Fields

1. Select each desired programming option, and then select the required entry. The system beeps each time a selection is made. 2. The system will toggle or scroll through the options or display a new screen as required for the specific option. 3. To delete or change an entry, simply select the desired option, and then select the required entry.

Loading a Default Set:

1. Enter the Installer Programming Mode and advance to second page of the System Programming. 2. Select ‘Default Config’ and select the appropriate Default Table Configuration from the following options or Select Default Downloader to reset all subscriber account numbers and CSID in preparation for an initial download:

Default Config 1 Default Config 2 Default Config 3 Default Config 4 Default Downloader

Note: Refer to the Programming Default Tables section of this manual to view the default values.

Exiting Programming Mode:

1. Select the “»” key to exit the current screen. The system returns to the previous screen. 2. Select the “»” key as required until system displays a Confirmation screen. 3. Select “Yes” to allow the installer to re-enter Programming mode or “No” to prevent re-entry. If “No” is selected, you can still re-enter Program Mode by powering down the unit (remove AC and battery power) and entering Program Mode within 30 seconds of powering up. 4. Select the “»” key again to return to the Home Screen.

-3-

Screen Display

Function & Programming Options

DATA FIELDS

Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen display.

Change Installer Code

Installer Code

5000-100-129-V0

Installer Code Enter 4 digits [The defaulted Installer Code is 4112] 0-9

Program System Type

RF Jam Disabled Speaker Phone Enabled Two Way Voice Disabled RF House Code 0 Phone Notification Disabled RF Jam Disabled Enabled Speaker Phone Disabled Enabled Two-Way Voice Disabled Enabled RF House Code Enter 2 digits, 00-31 Phone Notification Disabled Keypad Trouble

Note: If “Keypad” or “Trouble” is selected you will be prompted to program a phone detect time.

Phone Detect Time 2 Minutes

Phone Detect Time 1 Minute 2 Minutes 3 Minutes 4 Minutes Remote Phone Disabled Enabled Events – Log All

Note: If Press to Log All is selected the system will log the following events:

Remote Phone Enabled Events — Log All Press To Log All

Alarm Bypass Open/Close Trouble Non-Security

Events – Log Alarm Enabled Events – Log Bypass Disabled Events – Log Open Close Disabled Events – Log Trouble Enabled Non Security Disabled

Events – Log Alarm Enabled Disabled Events – Log Bypass Enabled Disabled Events — Log Open/Close Enabled Disabled Events – Log Trouble Enabled Disabled Non Security Enabled Disabled

-4-

Screen Display

Remote Access Serial Disabled Remote Access Serial Enabled Disabled

Function & Programming Options

Note: If the “Remote Access Serial” option is enabled, you will be prompted to select a “Multi Mode Serial”.

Multi Mode Serial Disabled

Multi Mode Serial Enhanced Reports Disabled

Program Date and Time

Date Time

5000-100-131-V0

Date Time

Note: If you are installing a GSMVLP5 or ILP5 Communication Module, the time and date will be programmed and updated automatically via Central Station. You must still program the correct Time Zone below.

1. 2. 3. 4. 5. Time Zone Eastern (EST)

Month and Year Select the correct date Enter the correct time Select AM or PM Select Save or continue below.

Time Zone Eastern (EST) Central (CST) Mountain (MST) Pacific (PST) Hawaii (HAST) Alaska (AKST) Day Light Savings Time Yes No Note: If Yes is selected, the following options will be active. Start Month January February March April May June Start Week First Second Third Fourth Last Next to Last 3rd from Last End Month January February March April May June Start Week First Second Third Fourth Last Next to Last 3rd from Last July August September October November December July August September October November December

Day Light Savings Time Yes

Start Month March

Start Week Second

End Month November

End Week First

-5-

Screen Display

Function & Programming Options

Program Communications

Communicator

5000-100-132-V0

Communications Path None APL Disabled City ID

CS ID

Sub ID

Supervision 24 Hours Old Alarm Time 10 Minutes

Remote Acc. IP or GSM Disabled Multi Mode IP or GSM Disabled GSM Fault Time (min) 00 IP Fault Time (min) 00 Use DHCP Yes NIC IP Address 255.255.255.255 Subnet Mask 255.255.255.255 Gateway IP Address 255.255.255.255

Communicator Program the following options: Communications Path APL City ID CS ID Sub ID Supervision Old Alarm Time Remote Acc. IP or GSM Multi Mode IP or GSM GSM Fault Time OR IP Fault Time Communications Path None IP GSM Advanced Protection Logic Enabled Disabled Primary City Identification Enter 2 digits 01-99 Primary Central Station Identification Enter 2-digits (HEX) 01-FE Primary Subscriber Identification Enter 4-digits 0001-9999 Supervision 24 Hours None 30 Days Old Alarm Time 10 Minutes 15 Minutes 30 Minutes 1 Hour 2 Hours 4 Hours 8 Hours 12 Hours 24 Hours Remote Access IP or GSM Disabled Enabled

Note: If enabled the following option will be active.

Multi Mode IP or GSM Disabled Relay Reports Enhanced Reports GSM Fault Time (min) (displayed if GSM is selected as Communications Path) Enter 2-digits 00-99 IP Fault Time (min) (displayed if IP is selected as Communications Path) Enter 2-digits 00-99 Use DHCP Note: If disabled the following options will be active. Yes No IP Fault Time Enter 4 part address Subnet Mask Enter 4 part address Gateway IP Address Enter 4 part address

-6-

Screen Display

DNS Server IP Address 255.255.255.255 DNS Server Address Enter 4 part address

Function & Programming Options

Program Zones

Zones

5000-100-133-V0

Serial Number

Zones Select from the following zone options: 2. Front Door 1. New 4.Window 3. Back Door 6.New 5. Motion Sensor 7. – 48. New 49. – 56. 4 Button 57. – 64. New 95. Fire 96. Medical 99. Police Select a zone and then select “Edit” or “Add New” to program the next available zone. Program the following options:(dependent upon Zone Type): Serial Number Loop Number Zone Description 1 Zone Description 2 Device Type Response Type Report Chime Supervision Serial Number When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed. The transmitter serial number and loop number can be enrolled via RF transmission OR manually. Enroll via RF Learning To enroll the device using RF Learning mode three transmissions (open/close) of the device will be required. The initial transmission activates the RF Learning mode and the system will emit a single beep. A second transmission enrolls the serial number and the system beeps two times and displays “Activate Sensor Again To Confirm”. A third transmission will confirm the serial number. The system beeps two times and returns to the Zone programming Screen. Enroll Manually Enter the 7-digit serial number printed on the transmitter using the displayed keypad and select “Done”. The system beeps one time and returns to the Zone programming Screen. Loop Number 1, 2, 3 or 4 Zone Description 1 The system announces the Zone Description. If desired, enter a zone descriptor. Zone Description 2 The system announces the Zone Description. If desired, enter a zone descriptor. Device Type Choose from the following options (dependant upon the Zone): New Door Window Motion Sensor Glass Break Smoke Detector Heat Sensor Carbon Mono. Det. Temperature Flood Environmental Medical Fire Police Other Response Type Choose from the following options (dependant upon the Zone): Not Used Arm Stay Entry Exit 1 Disarm Entry Exit 2 Silent Burglary Interior Follower Resident Response 24 Hour Silent General Response 24 Hour Auxiliary Perimeter Interior With Delay Day Night Carbon Monoxide 24 Hour Audible

Loop Number 1 Zone Description 1 Zone Description 2

Device Type

Response Type Not Used

Fire No Verification Monitor Trouble Arm Away No Response Resident Monitor General Monitor Fire With Verification

-7-

Screen Display

Report Yes Chime No Supervision Supervised Report Yes No Chime Yes No

Function & Programming Options

Supervision Hardwire – Normally Open Hardwire – Normally Closed Hardwire – End of Line RF – Supervised RF – Unsupervised

Program Keys

Keys Keys Select from the following options:

Edit Add New Key Type Serial Number Button Key 1 – Zn 49 Button Key 3 – Zn 51 Button Key 5 – Zn 53 Button Key 7 – Zn 55 Key Type 1 Button Key. 2 Button Key 4 Button Key 6 Button Key 8 Button Key User Master Duress Babysitter User 3 through User 14

Delete

If add new is selected the following options can be programmed:

User Zone Button Key 2 – Zn 50 Button Key 4 – Zn 52 Button Key 6 – Zn 54 Button Key 8 – Zn 56

Key Type 4 Button Key

User

Note: The Key must be associated with a specific User/User Code in order for it to operate. Refer to the LYNX Touch User Guide for additional Information regarding User Codes.

Serial Number 0

Serial Number When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed. The transmitter serial number and loop number can be enrolled via RF transmission OR manually. Enroll via RF Learning To enroll the device using RF Learning mode three transmissions (open/close) of the device will be required. The initial transmission activates the RF Learning mode. A second transmission enrolls the serial number and the system beeps two times and displays “Activate Sensor Again To Confirm”. A third transmission will confirm the serial number. The system beeps two times and returns to the Zone programming Screen. Enroll Manually Enter the 7-digit serial number printed on the transmitter using the displayed keypad and select “Done”. The system beeps one time and returns to the Zone programming Screen

Zone 49 Button Key * — Zone *

Zone Manually enter a specific two-digit Zone Number (49-64). Button Key * Zn * Enter a function for each button key from the following options: Disarm Arm Away Arm Stay No Response 24 Hour Silent 24 Hour Audible 24 Hour Auxiliary Silent Burglary Fire No Verification

* Options are the same for each Button/Zone combination.

-8-

Screen Display

Function & Programming Options

Reporter Program the following options: Primary CS Info Secondary CS Info Follow Me Phone 1 Follow Me Phone 2 Report Selection Options Downloader Primary Central Station Information Phone Type Communicator Type Phone Type None Contact Id : 4 Digit Contact Id : 10 Digit SIA

Note: If SIA, Contact Id: 4 Digit, or Contact Id: 10 Digit is selected the Phone Number and Account Number options will be displayed.

Program Reporter

Reporter

Primary CS Info Phone Type Contact Id: 4 Digit

Communicator Type None

Communicator Type None GSM IP

Note: If IP is selected the Dynamic Priority option will be displayed.

Phone Number Account Number FFFF Dynamic Priority

Phone Number Enter the Primary Central Station Phone Number Account Number Enter the Primary Central Station Account Number Dynamic Priority Redundant Reports Preferred Telco Preferred Radio

Note: If Preferred Telco or Preferred Radio is selected the Dynamic Delay option will be displayed.

Dynamic Delay

Report All Press to Report All Report Alarms Enabled Report Troubles Enabled Report Open/Close Disabled Report Tests Enabled Secondary CS Info Phone Type None

Dynamic Delay 15 Seconds 30 Seconds 60 Seconds 90 Seconds Report All Press to Report All Report All Set Report Alarms Disabled Enabled Report Troubles Disabled Enabled Report Open/Close Disabled Enabled Report Tests Disabled Enabled Secondary Central Station Information Phone Type Communicator Type Phone Type None Contact Id: 4 Digit Contact Id: 10 Digit SIA

Note: If SIA, Contact Id: 4 Digit or Contact Id: 10 Digit is selected, the Phone Number and Account Number options will be displayed.

-9-

Screen Display

Communicator Type None Communicator Type None GSM IP

Function & Programming Options

Note: If IP is selected the Dynamic Priority option will be displayed.

Phone Number

Phone Number Enter the Secondary Central Station Phone Number Account Number Enter the Secondary Central Station Account Number Dynamic Priority Redundant Reports Preferred Telco Preferred Radio Dynamic Delay None 15 Seconds 30 Seconds 60 Seconds 90 Seconds Report All Press to Report All Report All Set Report Alarms Disabled Enabled Report Troubles Disabled Enabled Report Open/Close Disabled Enabled Report Tests Disabled Enabled Follow Me Phone 1 Choose from the following options: Phone Type Phone Number Report All Report Alarms Report Troubles Report Open/Close Report Tests Phone Type None Follow me Phone Number Enter the Follow Me Phone Number Report All Press to Report All Report All Set Report Alarms Disabled Enabled Report Troubles Disabled Enabled Report Open/Close Disabled Enabled

Account Number FFFF Dynamic Priority None

Note: If Preferred Telco or Preferred Radio is selected the Dynamic Delay option will be displayed.

Dynamic Delay None

Report All Press to Report All Report Alarms Enabled Report Troubles Disabled Report Open/Close Disabled Report Tests Enabled Follow Me Phone 1

Phone Type None Phone Type None Report All Press to Report All Report Alarms Disabled Report Troubles Disabled Report Open/Close Disabled

— 10 —

Screen Display

Report Tests Disabled Follow Me Phone 2 Report Tests Disabled Enabled

Function & Programming Options

Follow Me Phone 2 Choose from the following options: Phone Type Phone Number Report All Report Alarms Report Troubles Report Open/Close Report Tests Phone Type None Follow me Phone Number Enter the Follow Me Phone Number Report All Press to Report All Report All Set Report Alarms Disabled Enabled Report Troubles Disabled Enabled Report Open/Close Disabled Enabled Report Tests Disabled Enabled Report Selection Choose from the following options: Arm Away Arm Stay Disarm Exit Error Recent Closing Event Log Full Trouble Trouble Restore Alarm Restore Alarm Cancel Test Test Restore Arm Away Disabled Enabled Arm Stay Disabled Enabled Disarm Disabled Enabled Exit Error Disabled Enabled Recent Closing Disabled Enabled Event Log Full Disabled Enabled Trouble Disabled Enabled

Phone Type None Phone Number Report All Press to Report All Report Alarms Disabled Report Troubles Disabled Report Open/Close Disabled Report Tests Disabled Report Selection

Bypass AC Loss Low Battery RF Low Battery Bypass Restore AC Loss Restore

Low Battery Restore RF Low Battery Restor

Arm Away Enabled Arm Stay Enabled Disarm Enabled Exit Error Enabled Recent Closing Enabled Event Log Full Enabled Trouble Enabled

— 11 —

Screen Display

Trouble Restore Enabled Alarm Restore Enabled Alarm Cancel Enabled Test Enabled Test Restore Enabled Bypass Enabled Bypass Restore Enabled AC Loss Enabled AC Loss Restore Enabled Low Battery Enabled Low Battery Restore Enabled RF Low Battery Enabled RF Low Battery Restore Enabled Options

Function & Programming Options

Trouble Restore Disabled Enabled Alarm Restore Disabled Enabled Alarm Cancel Disabled Enabled Test Disabled Enabled Test Restore Disabled Enabled Bypass Disabled Enabled Bypass Restore Disabled Enabled AC Loss Disabled Enabled AC loss Restore Disabled Enabled Low Battery Restore Disabled Enabled Low Battery Restore Disabled Enabled RF Low Battery Disabled Enabled RF Low Battery Restore Disabled Enabled Options Choose from the following options: PBX Call Wait Cancel Number of Reports Alarm Report Delay First Report Offset Report Frequency PBX Enter PBX Prefix Call Wait Cancel Enter Call Wait Cancel Prefix Number of Reports Unlimited 10 Reports Alarm Report Delay No Delay 15 Sec. 30 Sec. 45 Sec.

PBX Call Wait Cancel Number of Reports Unlimited Alarm Report Delay No Delay

— 12 —

Screen Display

First Report Offset 6 Hrs First Report Offset 6 Hrs 12 Hrs 18 Hrs 24 Hrs Report Frequency Never Every Day Every 7 Days Every 30 Days

Function & Programming Options

Report Frequency Never

Downloader

Downloader

Choose from the following options: Phone Answer Modem Speed Ans. Machine Defeat Callback Number Ring Counter Flexible Callback Number Phone Answer Yes No Modem Speed (Future Use) Answering Machine Defeat Yes No Callback Number Enter a Callback Number Ring Counter (displayed if Ans. Machine Defeat is set to “No”) Enter ring counter (1-14) Flexible Callback Yes No Number (displayed if Flexible Callback is set to “Yes”) Enter the number of flexible callbacks that will be used (1-3)

Phone Answer Yes Modem Speed Slow Ans. Machine Defeat Yes Callback Number Yes Ring Counter 2 Flexible Callback No Number

Program Sounder

Sounder

Sounder

Choose from the following options: Burglary Alarm Sound Burglary Bell Timeout Fire Bell Timeout Arm Confirm Alarm Options

Burglary Alarm Sound Yes Burglary Bell Timeout 4 Minutes

Burglary Alarm Sound

Yes No

Burglary Bell Timeout

No 4 Minutes 8 Minutes 12 Minutes 16 Minutes No 4 Minutes 8 Minutes 12 Minutes 16 Minutes

Fire Bell Timeout 4 Minutes

Fire Bell Timeout

— 13 —

Screen Display

Arm Confirm None

Function & Programming Options Arm Confirm

None All RF RF Key Fob RF Keypad

Alarm Options Unlimited

Alarm Options

Unlimited 1 2 10

Program System Settings

System Settings

System Settings

Choose from the following options: Entry Delay 1 Entry Delay 1 Exit Delay Backlight Timeout Quick Arm Quick Exit Restart Exit Time Force Bypass Exit Warning Auto Stay Arming Lack of Usage Notify Power-up in Previous Display Alarm Cancel Display Exit Time Cross Zone Delay Cross Zone 1 Cross Zone 2 None 15 Seconds 30 Seconds 45 Seconds 60Seconds 90 Seconds 2 Minutes None 15 Seconds 30 Seconds 45 Seconds 60Seconds 90 Seconds 2 Minutes

Entry Delay 1 30 Seconds

Entry Delay 1

Entry Delay 2 30 Seconds

Entry Delay 2

Exit Delay 30 Seconds

Exit Delay

None 15 Seconds 30 Seconds 45 Seconds 60Seconds 90 Seconds 2 Minutes

Backlight Timeout No Quick Arm Yes Quick Exit No Restart Exit Time No

Backlight Timeout

No 30 Seconds Yes No Yes No Yes No

Quick Arm Quick Exit

Restart Exit Time

— 14 —

Screen Display

Force Bypass No Exit Warning No Auto Stay Arming No Lack of Usage Notify Disabled

Function & Programming Options Force Bypass

Yes No Yes No Yes No

Exit Warning Auto Stay Arming Lack of Usage Notify

Disabled 1 Day 7 Days 27 Days 90 Days 180 Days 365 Days Yes No Yes No Yes No

Power-Up in Previous Yes Display Alarm Cancel No Display Exit Time Yes Cross Zone Delay 3 Minutes

Power-Up in Previous State Display Alarm Cancel

Display Exit Time

Cross Zone Delay

None 30 Seconds 1 Minute 90 Seconds 2 Minutes 3 Minutes 4 Minutes Disabled

Cross Zone 1 Disabled Cross Zone 2 Disabled

Cross Zone 1

Cross Zone 2

Disabled

— 15 —

Zone Programming Worksheet

Fill in the required data on this worksheet, then follow the programming procedure. See Explanation of Zone Assignment Table Headings (defaults shown are for Table 1)

Zone No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Loop No. N/A 2 2 2 1 Device Type New Door Door Window Motion Sensor Response Type N/A Entry Exit 1 Entry Exit 1 Perimeter Interior w/Delay Report Chime Yes No Yes Yes Yes Yes Yes Yes Yes No Supervision End of Line RF Supervised RF Supervised RF Supervised RF Supervised Transmitter Serial Number N/A Zone Descriptor (HW Zone) Front Door Back Door

— 16 —

Zone Programming Worksheet

Zone No. 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 92 95 96 97 99 N/A N/A N/A N/A N/A N/A Fire Medical N/A Police 24 Hour Silent N/A Fire No Verif. Not Used Yes Yes Yes Yes Yes No No No No No Duress Trigger Panic Trigger Panic Trigger Cover Tamper Panic Trigger N/A N/A 3 2 4 1 3 2 4 1 4 Button (Key) 4 Button (Key) 4 Button (Key) 4 Button (Key) 4 Button (Key) 4 Button (Key) 4 Button (Key) 4 Button (Key) Arm Away Disarm Arm Stay No Response Arm Away Disarm Arm Stay No Response Yes Yes Yes No Yes Yes Yes No No No No No No No No No Button Button Button Button Button Button Button Button N/A N/A N/A N/A N/A N/A N/A N/A Loop No. Device Type Response Type Report Chime Supervision Transmitter Serial Number Zone Descriptor

— 17 —

Explanation of Zone Assignment Table Headings

Used with 5800 Devices. Record transmitter loop number. Entries are 1-4, depending on device being used. Refer to the transmitter’s instructions or the figure provided for appropriate loop numbers.

Loop Number

Dependant upon the Zone Number being programmed. Door Smoke Detector Window Heat Sensor Motion Sensor Carbon Mono. Det. Glass Break Temperature

Device Type

Flood Environmental Medical Police

Fire Other

Dependant upon the Device Type that has been selected. Entry Exit 1 24 Hour Audible Entry Exit 2 24 Hour Auxiliary Perimeter Fire No Verification Interior Follower Interior with Delay Day Night Monitor 24 Hour Silent Carbon Monoxide

Response Type

Trouble Arm Stay Arm Away Disarm No Response Silent Burglary

Resident Monitor Resident Response General Monitor General Response Fire With Verification

Dependant upon the Zone Number being programmed. Hardwire Zone (Zone 1) Wireless Zone (Zone 2-48) End of Line (Resistor) Supervised Normal-Closed Unsupervised Normal-Open

Supervision

Key (Zone 49-64) Button

— 18 —

5800 Series Transmitter Loop Numbers

LOOP 1 LOOP 1 LOOP 1 5800CO ENROLL AS «RF» 5800Micra ENROLL AS «RF» 5800PIR-RES ENROLL AS «RF» LOOP 1 (LOW SENSITIVITY LOOP 2 (HIGH SENSITIVITY) LOOP 3 (TEMP) LOOP 4 (TAMPER) 5800PIR/ 5800PIR-COM ENROLL AS «RF» LOOP 1 (LOW SENSITIVITY LOOP 2 (HIGH SENSITIVITY) LOOP 3 (TEMP) LOOP 4 (TAMPER) 5800PIR-OD ENROLL AS «RF» 5800RL SET HOUSE ID LOOP 2 LOOP 4 LOOP 3 LOOP 1

LOOP 3 LOOP 4 LOOP 1 LOOP 1 LOOP 1 LOOP 1

ON OFF

LOOP 2 LOOP 1

•• •• •• •• • • • •• • •• • ••

5800SS1 E N RO L L A S » R F «

5 8 0 0 WAV E P RO G R A M HOUSE ID

5802MN ENROLL AS «UR» OR «RF»

5802MN2 ENROLL AS «UR» OR «RF»

5804/5804E ENROLL AS «BR»

5 8 0 4 B D / 5 8 0 4 B DV ENROLL AS «BR» PROGRAM HOUSE ID

SERIAL #1 LOOP 3

ON

SERIAL #1 LOOP 4 SERIAL #2 LOOP 3

1

OF

F

SERIAL #1 LOOP 2 SERIAL #1 LOOP 1 SERIAL #2 LOOP 2 5806/5806W3/5807 5808/5808LST/5808W3 ENROLL AS «RF» LOOP 1 LOOP 1 LOOP 1 LOOP 1

2 3 4

LOOP 2 (REED) LOOP 1 (TERMINALS)

SERIAL #2 — LOOP 1 = ON + 4 BUTTONS LOOP 4 = 3 + 4 BUTTONS 5805-6 ENROLL AS «BR»

5809 ENROLL AS «RF»

5811 ENROLL AS «RF»

5814 ENROLL AS «RF»

5816 ENROLL AS «RF»

LOOP 1 (PRIMARY) LOOP 2 (REED) LOOP 1 (TERMINALS) ALTERNATE POSITION FOR LOOP 2 5816MN ENROLL AS «RF» LOOP 1 (TEMP SENSOR) LOOP 2 (AUX. CENTER) LOOP 3 (AUX. RIGHT) 5817 ENROLL AS «RF»

LOOP 2 (REED)

LOOP 2 (REED) LOOP 3 (TERMINALS) LOOP 1

LOOP 1

LOOP 3 (TERMINALS) LOOP 1 (TERMINALS) 5819 ENROLL AS «RF»

5816TEMP ENROLL AS «RF»

5818 ENROLL AS «RF»

LOOP 1 (INTERNAL SHOCK SENSOR 5819S (WHS & BRS) ENROLL AS «RF»

5820L ENROLL AS «RF»

SERIAL #1 LOOP 3

AR ME D

SERIAL #2 LOOP 1 SERIAL #1 LOOP 2 SERIAL #2 LOOP 4 LOOP 1 SERIAL #1 LOOP 1 5853 ENROLL AS «RF» 5870API ENROLL AS «RF» LOOP 1 (HIGH SECURITY) LOOP 2 (STANDARD SECURITY) LOOP 3 (TILT MODE) LOOP 4 (TAMPER) SERIAL #1 LOOP 3 SERIAL #1 LOOP 4 SERIAL #2 LOOP 3

AW AY ST AY 1 2 3 4

RE

AD

Y

LOOPS 1-3

SERIAL #2 LOOP 3 SERIAL #1 LOOP 4 5828/5828V P RO G R A M HOUSE ID SERIAL #2 LOOP 2 5834-4 ENROLL AS «BR»

SERIAL #1 LOOP 2 SERIAL #1 LOOP 1 SERIAL #2 LOOP 2

5821 ENROLL AS «RF»

5878 ENROLL AS «BR»

LOOP 1 (MOTION)

LOOP 1 (LOW SENSITIVITY) LOOP 1 LOOP 1 LOOP 2 (HIGH SENSITIVITY)

5890/5890PI ENROLL AS «RF»

5894PI ENROLL AS «RF»

5897 ENROLL AS «RF»

5898 ENROLL AS «RF»

Notes: (1) Button type (BR) devices send only fault and low battery signals; no restore or check-in signals. Supervised RF (RF) devices send periodic check-in signals, faults, restore and low battery signals. Unsupervised RF (UR) devices send periodic check-in signals, faults, restore and low battery signals but the control does not supervise the check-in signals. . (2) If an external sounder is required, the 5800WAVE should be used.

UL

The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5814, 5816TEMP, 5819, 5819S(WHS & BRS), and 5828/5828V wireless transmitters have not been evaluated by UL.

— 19 —

5800-002-V0

Programming Default Tables

Program Function Installer Code System Type RF Jam Speaker Phone Two Way Voice RF House Code Phone Notification Remote Phone Phone Detect Time Events — Log All Events — Log Alarm Events — Log Bypass Events — Log Open/Close Events — Log Trouble Non Security Remote Access Serial Multi Mode Serial Date Time Calendar Enter Time Time Zone Day Light Savings time Start Month Start Week End Month End Week Communicator Communications Path APL City ID CS ID Sub ID Supervision Old Alarm Time Remote Acc. IP or GSM Multi Mode IP or GSM GSM Fault Time IP Fault Time Use DHCP NI IP Address Subnet Mask Gateway IP Address DNS Server IP Address Zones Reporter Primary CS Info Phone Type Communicator Type Phone Number Account Number Dynamic Priority Dynamic Delay Report All Report Alarms Report Troubles Report Open/Close Report Tests Secondary CS Info Phone Type Communicator Type Phone Number Account Number Dynamic Priority Dynamic Delay Report All Report Alarms Report Troubles Report Open/Close Report Tests Table 1 4112 Disabled Enabled Disabled 0 Disabled Enabled 2 Minutes Press To Log All Enabled Disabled Disabled Enabled Disabled Disabled Disabled January 1, 2011 10:00AM Eastern (EST) Yes March Second November First None Disabled None None None 24 Hours 10 Minutes Disabled Disabled 00 00 Yes 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 Table 2 4112 Disabled Enabled Disabled 0 Disabled Enabled 2 Minutes Log All Set Enabled Enabled Enabled Enabled Enabled Disabled Disabled January 1, 2011 10:00AM Eastern (EST) Yes March Second November First Table 3 4112 Disabled Enabled Disabled 0 Disabled Enabled 2 Minutes Log All Set Enabled Enabled Enabled Enabled Disabled Disabled Disabled January 1, 2011 10:00AM Eastern (EST) Yes March Second November First Table 4 4112 Disabled Enabled Disabled 0 Disabled Enabled 2 Minutes Log All Set Enabled Enabled Enabled Enabled Disabled Disabled Disabled January 1, 2011 10:00AM Eastern (EST) Yes March Second November First None Disabled None None None 24 Hours 10 Minutes Disabled Disabled 00 00 Yes 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255

None None Disabled Disabled None None None None None None 24 Hours 24 Hours 10 Minutes 10 Minutes Disabled Disabled Disabled Disabled 00 00 00 00 Yes Yes 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 See Zone Programming Default Tables

Contact Id: 4 Digit None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled None None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled

Contact Id: 4 Digit None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled None None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled

Contact Id: 4 Digit None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled None None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled

Contact Id: 4 Digit None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled None None None FFFF None None Press to Report All Enabled Enabled Disabled Enabled

— 20 —

Program Function Follow Me Phone 1 Phone Type Phone Number Report All Report Alarms Report Troubles Report Open/Close Report Tests Follow Me Phone 2 Phone Type Phone Number Report All Report Alarms Report Troubles Report Open/Close Report Tests Report Selection Arm Away Arm Stay Disarm Exit Error Recent Closing Event Log Full Trouble Trouble Restore Alarm Restore Alarm Cancel Test Test Restore Bypass Bypass Restore AC Loss AC Loss Restore Low Battery Low Battery Restore RF Low Battery RF Low Battery Restore Options PBX Call Wait Cancel Number of Reports Alarm Report Delay First Report Offset Report Frequency Downloader Phone Answer Ans. Machine Defeat Modem Speed (Future Use) Ring Counter Callback Number Flexible Callback Number Sounder Burglary Alarm Sound Burglary Bell Timeout Fire Bell Timeout Arm Confirm Alarm Options System Settings Entry Delay 1 Entry Delay 2 Exit Delay Backlight Timeout Quick Arm Quick Exit Restart Exit Time Force Bypass Exit Warning Auto Stay Arming Lack Of Usage Notify

Table 1 None None Press To Report All Disabled Disabled Disabled Disabled None None Press To Report All Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Blank Blank Unlimited No Delay 6 Hrs Never Yes Yes Slow 2 Blank No 1 Yes 4 Minutes 4 Minutes None Unlimited 30 Seconds 60 Seconds 60 Seconds No Yes Yes No No No No Disabled

Table 2 None None Press To Report All Disabled Disabled Disabled Disabled None None Press To Report All Disabled Disabled Disabled Disabled Enabled Enabled Enabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Blank Blank Unlimited 15 Seconds 12 Hrs 30 Days Yes Yes Slow 2 Blank No 1 Yes 4 Minutes 4 Minutes None 2 45 Seconds 60 Seconds 60 Seconds No Yes Yes Yes No Yes Yes Disabled

Table 3 None None Press To Report All Disabled Disabled Disabled Disabled None None Press To Report All Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Blank Blank Unlimited No Delay 12 Hrs Never Yes Yes Slow 2 Blank No 1 Yes 4 Minutes 4 Minutes None 2 30 Seconds 60 Seconds 60 Seconds No Yes Yes Yes No Yes Yes Disabled

Table 4 None None Press To Report All Disabled Disabled Disabled Disabled None None Press To Report All Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Blank Blank Unlimited No Delay 12 Hrs Never Yes Yes Slow 2 Blank No 1 Yes 4 Minutes 4 Minutes None 2 30 Seconds 60 Seconds 60 Seconds No Yes Yes Yes No Yes Yes Disabled

— 21 —

Program Function Power-Up In Previous Display Alarm Cancel Display Exit Time Cross Zone Delay Cross Zone 1 Cross Zone 2

Table 1 Yes No Yes 3 Minutes Disabled Disabled

Table 2 Yes Yes Yes None Disabled Disabled

Table 3 Yes Yes Yes None Disabled Disabled

Table 4 Yes Yes Yes None Disabled Disabled

— 22 —

THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION STANDARDS ANSI/NFPA 70 NATONAL ELECTRIC CODE AND NFPA 72 NATIONAL FIRE ALARM CODE, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOC., BATTERY MARCH PARK, QUINCY, MA 02169). PRINTED INFORMATION ESCRIBING PROPER INSTALLATION, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT. LYNX TOUCH SERIES ALSO COMPLIES WITH THE FOLLOWING: CANADIAN STANDARDS ASSOCIATION (CSA) C22.1, CANADIAN ELECTRICAL CODE, PART 1, SAFETY STANDARD FOR ELECTRICAL INSTALLATIONS AND CAN/ULC-S540 INSTALLATION OF RESIDENTIAL FIRE WARNING SYSTEMS.

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

NOTE: THE HARDWIRE ZONE CANNOT BEUSED AS A FIRE ZONE. PREMISES TELEPHONE INCOMING PHONE LINE

STANDARD CAPACITY BATTERY CONNECTOR

WARNING TO PREVENT RISK OF SHOCK, DISCONNECT TELEPHONE LINE AT TELECOM JACK BEFORE SERVICING THIS UNIT HARD WIRED ZONE 2K OHM EOLR 300-04705 or 300-04065 (300-04063 CANADA) POWER SUPPLY 9V, 2.7A

INCOMING PHONE LINE

IMPORTANT Be sure to observe polarity when connecting the power supply to the terminal strip.

SUPER HIGH CAPACITY BATTERY CONNECTOR

EARTH GROUND

UL INSTALLATIONS THE MINIMUM WIRE SIZE USED FOR TELEPHONE INSTALLATIONS MUST BE #26 GAGE RING TIP RING

TRIGGER OUTPUT (NEG) (3ma)

TIP

POWER SUPPLY CONNECTOR

TIP

RING

H/S T

EGND

HWZ1

TRIG

PHONE

H/S R

ZONES

POWER

GSMVLP5/ILP5 RECEPTACLE

+9VDC GND

TELCO JACK

GND

-23TAMPER SWITCH

EDGE CONNECT (FUTURE USE)

EDGE CONNECT (FUTURE USE)

WARNING

THIS UNIT MAY BE PROGRAMMED TO INCLUDE AN ALARM VERIFICATION FEATURE THAT WILL RESULT IN A DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED FIRE CIRCUITS. THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL NOT EXCEED 60 SECONDS. NO OTHER INITIATING DEVICES SHALL BE CONNECTED TO THESE CIRCUITS UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION.

COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION No. AC3AL05BL5000 RINGER EQUIVALENCE: 0.5B

THE LYNX TOUCH CONTROLS ARE COMPATIBLE WITH THE FOLLOWING INTEGRAL RECHARGEABLE BATTERY PACKS:

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM

CIRCUIT (ZONE) 02 — 48 ZT16

CONTROL UNIT DELAY-SEC 30 seconds

SMOKE DETECTOR MODEL DELAY-SEC 5806W3 10 seconds

P/N 300-03864-1/LYNXRCHKIT-SC P/N 300-03866/LYNXRCHKIT-SHA

REPLACE EVERY FOUR YEARS

LYNX TOUCH SERIES SUMMARY OF CONNECTIONS

5000-100-SOC-V0

2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747

Copyright © 2011 Honeywell International Inc. www.honeywell.com/security

Ê800-06895V1%Š

800-06895V1 8/11 Rev. A

Download the Honeywell Lynx Touch (L5000, L5100, L5210, L7000) Quickstart HERE

Throughout Programming anytime the system asks for codes, please use the codes below:

Installer Code- 4112
Master Code- 1234

(Note: These are the default codes and can later be changed.  We recommend only changing the Master Code and do not change the Installer Code.  If you change the installer code, be sure to write it down and remember it, you will not be able to program the system if you lose that code.)

Zone Information:

Zone 1- Hardwired Only

Zones 2-48 Wireless Device

Zones 49-64 Wireless Buttons

Step 1:  NOTE: When connecting your power supply (Power Transformer) to your Lynx System, be sure to pay attention to the polarity.  The positive terminal on the transformer will be wired to the 9v+ on the Lynx Touch.  The negative (-) on the power transformer will go the Ground (GND) next to the 9v+.

Step 2:  Default your System: When the system is powered on and you see the main screen, touch the tab on the bottom right that says “more”, then touch tools, then enter 4112, then touch “program”, then hit the down arrow on the right, then touch “default config”, and the hit “default config 1”, and then hit “yes” to confirm.

Then hit the return arrow (top right) one time.  We will now set your System Settings.

Step 3: System Settings: Assuming you just defaulted your system, you are now ready to set your systems settings.  Touch the tab the says “System Settings”.  The screen will now display your current settings.  NOTE: The main ones you are worried about will be the top two lines (Entry and Exit delays) and making changes to anything else in this section will not be covered in this quick start guide.

To Set your Entry and Exit delay times, just simply tap the delay time you are wanting to change until your desired time is displayed (15, 30, 45, 60, 90, 2 min, none).

When you have entered your times, Hit “Save”.  You should then see an up arrow on the right hand side.  Hit the up arrow. (At this time you should see the system programming menu that displays the installer code, system type, date and time, zones, etc…)

Hit “Date and Time”

Setting Date and Time: You should now be able to set your date and time.  Simply use the arrow keys at the top to select your month, day, and year.  When you have the correct date, then hit the down arrow on the right to take you to the section for the time.  Simply enter your current time.  You may need to hit the left delete arrow to erase a default time.  You must enter 4-digits for the time.  And then tap am/pm to select the appropriate time of day.  When your date and time is set, hit “save” and this will take you back to the programming menu.

We are now ready to enter your zone information.  It is best to make sure all of your wireless devices are ready to be enrolled.  You will want to make sure each sensor has a battery in it, and the magnets are next to the door/window sensors and all covers back on. Then go ahead and touch the “zones” tab in the system programming menu.

Step 4: Entering Zones: You are now ready to enter your wireless devices.  You will not use Zone 1 for any wireless device.  Zone 1 is for hardwired only.  All wireless devices begin with zone 2.  All key fobs or wireless panic buttons will not be entered into this section.

If you have any questions about “Loops” and what loop should be programmed, refer to the Lynx Touch Installation and Setup Guide, page 14.  However, by defaulted, while programming the activated loop automatically is inputted in the control panel.

With each device now powered by battery, covers on, and ready to be programmed, go ahead and select your Zone 2 (by default says Front Door), and once it is highlighted, click edit.

Enrolling the Device:  You can either enter the number manually without using the “A” (if you choose this way, make sure you select the correct loop). OR you can enroll by transmitting the device.  To transmit the device, make sure you place the magnet next to the sensor, pull the magnet away and the system will beep.  Repeat and put the magnet next to the sensor and pull the magnet away.  The system will fill in the serial number and loop.  Just hit “done”.

Then choose your Zone Descriptor.  Begin typing what the device is for.  Once you hit the first letter, you can continue spelling the word or scroll through the words beginning with that letter.  This will mainly be the first word of the description, as you will select another word later.  Once you have the word you want select “done”

Then you will choose your device type.  Touch the “device type” tab and select what device you are working with.  You may need to use the up and down scroll arrows on the side.  Once you select that, the basic programming for that device is done, and you can hit “save”.

And now you are ready to program you next zone, repeating step 4.

Step 5:  Entering Key Fobs and other Wireless Keys (you can skip this step if you do not have a key fob or any RF buttons). While in System Programming, click on “Keys”.  You will select the section in which a particular key fob/button is assigned to.  You must edit the settings and must select a user for the key fob.  The key fobs will not work unless they are assigned to a user.

Enroll the Key fob’s serial number by entering selecting “serial number” and enter the ESN by only putting the numbers off the sticker (you do not need to put the letter “A”).  Hit done when you have entered the serial number.

Then select your device type (most common is 4 button).  Then select the type of response the button is supposed to do.  Then select if the item is supposed to report to the monitoring company if an alarm occurs.  Hit save.

Step 6:  Exit Programming by hitting the return back arrow (top right) and always hit “yes” to allow installer to re-enter programming.

Step 6: Changing Master Code and Adding/Deleting Users

Hit the “tools” tab (if you do not see it, hit “more” and then “tools”.  Enter the current Master code (by default it is 1234).  Select “Users”.  Here you can select “master code” and edit, enter the new code, and then “done”.  You can “add new” users and set their own code as well.  Only the Master Code will allow you to make changes to the users.  Users will not have access to make any changes.  These codes will allow you to arm or disarm the alarm.

Step 7: To enter a phone number(s) for self monitoring

At the bottom of the main screen you will see a tab called ‘More’. Touch this.

At the next screen touch the ‘Tools’ icon

You will then be asked to enter your installer code (The default is 4112)

At the next screen that appears touch the ‘Program’ icon

On the next screen touch the ‘Reporter’ icon

You will then see several options. You will either touch ‘Phone 1’ or ‘Phone 2’

Touch the ‘Phone Type’ icon until it changes to ‘Follow Me’

You will then touch the ‘Phone Number’ icon

Enter in the phone number in the screen that appears as you would dial the number from your house phone

You will then touch the ‘Done’ icon

You will then choose which reporting options you’d like the system to call out on. Either touch the ‘Report All’ icon or individually choose each reporting option by touching its icon.

After this is done touch the ‘Save’ icon and back all the way out of programming. (When doing this you will see a popup that will ask if you want to ALLOW INSTALLER TO BE ABLE TO RE-ENTER PROGRAMMING. Always choose YES

Продолжение по китайским сигнализациям. В интернете нормальной информации не встречал.
Большинство как говорится глюков сигнализаций является простыми дополнительными функциями, которые по не знанию можно случайно активировать.
Не во всех инструкциях есть информация по программированию.
Попалась как раз такая с порядком программирования. На коробке было написано «TOMAHAWK X5», но это такая же сигналка как я рассматривал выше (JVC, PIONEER). К томагавку она как мне кажется, ни каким боком на относится.
Программироваться система будет только при условии что все необходимые соединения при установке были выполнены. К ним относится — на замок зажигания к положению АСС, к педали тормоза, концевики дверей работают.

Пункты по программированию это №7, 15, 18.

Вот сама инструкция. Попробую перевести полностью, чтобы вопросов не было.

1. Постановка на охрану.
А. Нажать один раз на «закр. замок» на трансмиттере (пульт :D), сирена пикнет один раз, огни моргнут один раз, закроется центр замок. Спустя 3 секунды система встанет на охрану, светодиод начнёт мигать.
В. Во время срабатывания сигнализации, нажать один раз на «закр. замок», для остановки сработавшей системы, но оставив её под охраной.

2. Снятие с охраны.
А. Нажать один раз на «откр. замок» на трансмиттере, сирена пикнет дважды ( если не стояла тихая охрана пщать не будет), огни моргнут дважды, откроется центр замок, система снимется с охраны. Спустя 3 секунды система встанет на охрану, светодиод начнёт мигать.
В. Во время срабатывания сигнализации, нажать один раз на «откр. замок», для остановки сработавшей системы, снятия авто с охраны, и открытии центр замка.

3. Тихая охрана.
Нажать кнопку «динамик зачёркнут» на пульте, сирена пищать не будет, огни моргнут один раз, закроется центр замок. Спустя 3 секунды система встанет на тихую охрану, светодиод начнёт мигать.

4. Поиск автомобиля.
А. При охране или без неё нажать один раз на «колоколчик» на трансмиттере, сирена будет пищать 30 секунд, огни будут моргать 30 секунд, для поиска машины.
В. Во время движения, нажать один раз на «колоколчик», сирена будет пищать непрерывно 30 секунд, огни будут моргать 30 секунд.

5. Дистанционное открытие багажника. Необходимы дополнительные работы
А. Нажать на «откр. замок» на трансмиттере и удерживайте в течении 3 секунд, багажник откроется, и если машина находилась под охраной откроется центр замок и система снимется с охраны.
В. Нажать на кнопку «откр. багажника» на трансмиттере, багажник откроется, и если машина находилась под охраной центр замок останется закрытым но система снимется с охраны на некоторое время.
Для открытия багажника ОБЯЗАТЕЛЬНО ставить реле.

6. Охранная зона триггеров (концевиков дверей, багажника, капота).
В момент постановки на охрану, если к примеру неплотно закрыта дверь, сирена издаст 5 длинных сигналов, огни моргнут 5 раз. Включится блокировка двигателя.
Если триггер сработает по истечению 3 секунд после постановки в охрану (открыть дверь), Сирена начнёт продолжительно пищать, огни моргать. Спустя 30 секунд произойдёт автоматическая перепостановка на охрану.

7. Автоматическое закрытие центрального замка. (Функция является настраиваемой)</b>
А. При движении нажать «откр. замок» или «закр. замок» центр замок будет открываться и закрываться, но охран включаться не будет.
В. При закрытых дверях и включенном положении АСС в течении 15 секунд, нажать на педаль тормоза, центр замок закроется.
С. После выключения положения АСС центр замок откроется.

Включение и отключение автоматического закрытия центр замка.
При выключенной охране, открытой двери, моргают огни, включить положение АСС, нажать на педаль тормоза,
и нажать и удерживать кнопку «закр. замок» в течении 3 секунд. Сирена пикнет 2 раза — функция автоматического закрытия дверей активирована.
Для отключения функции повторить операцию. Сирена пикнет 1 раз — функция автоматического закрытия дверей отключена.

8. Парковочные огни.
При снятой охране, для безопасности при открытии дверей, в течении 30 секунд моргают огни.

9. Функция Anti- hijack.
При движении нажать кнопку «динамик зачёркнут», огни начнут моргать. Нажать на кнопку «закр. замок» огни перестанут моргать, через 15 секунд сирена начнёт пищать, огни моргать. Система автоматически войдёт в режим Anti- hijack, двигатель будет заблокирован. Для отключения нажать на кнопку «откр. замок».

10. Память положения триггеров.
При включенной охране, вся информация о изменении триггеров записывается в память. Пока владелец не проверит авто.
А. При снятии с охраны если срабатывал датчик удара сирена издаст 3 сигнала;
В. При снятии с охраны если срабатывал триггер двери сирена издаст 4 сигнала;
С. При снятии с охраны если включалось зажигание сирена издаст 5 сигналов.

11. Авто перепостановка.
Если после снятия охраны не открывалась дверь и не включалось АСС то спустя 30 секунд она автоматически снова ставится на охрану.

Начинает вызывать неудобства когда перестают работать концевики дверей. Садишся в машину а она закрывается.

12. Аварийное отключение.
При включенной охране, если брелок не исправен, дверь можно открыть ключом, включить положение АСС и выключить за 10 секунд, с момента открывания двери. Охрана будет снята.

13. LED индикатор.
А. При включенной охране светодиод моргает;
В. При выключенной охране светодиод потушен.

14. Отключение датчика удара.
В режиме охраны нажать кнопки «откр. замок» и «закр. замок» одновременно, огни моргнут 3 раза, Датчик удара будет исключён из работы. После снятия с охраны и при следующей её постановке он включится в работу автоматически.

15. Функция автоматической охраны.
А. После остановки и выключения положения АСС и последующим открытием и закрытием двери, через 10 секунд система издаст 3 сигнала предупреждая о поставке авто под охрану. Через одну минуту система автоматически войдёт в режим тихой охраны, но двери не заблокирует.
В. При снятой охране открыть дверь, огни начнут моргать, включить положение АСС, нажать и держать педаль тормоза,
и нажать и удерживать на брелке кнопку «динамик зачёркнут» в течении 3 секунд. (В инструкции пустое место странно! Сам долго думал как отключить на машине). Сирена пикнет 2 раза — функция включена. Для отключения повторить операцию. Сирена пикнет 1 раза — функция отключена.

16. Память при отключении питания.
В любом состоянии при отключении питания, система запоминает текущее состояние.
Например если снять клемму с АКБ при включенной охране, то после соединения клеммы сигнализация так же останется в режиме охраны.

17. Напоминание о незакрытых дверях.
Если при постановке на охрану не закрыта дверь. сирена пикнет 3 раза.

18. Обучение брелков.
При снятой охране открыть дверь, включить АСС 5 раз и оставить во включенном состоянии, сирена пикнет 1 раз, огни моргнут, говоря о том что система перешла в режим обучения брелков:
А. Нажать любую кнопку на брелке, сирена издаст один звук. Повторить операцию для других брелков.
Максимальное количество брелков 4. При записи пятого брелке система удалит все предыдущие и он станет первым. После записи брелков выключить положение АСС.
При обучении новых брелков, информация о старых брелках стирается.

Ещё пара функций которые можно переключать. Переключаются путём установки перемычек «джамперов».
Находятся внутри корпуса, на плате сигналки. А могут быть и сбоку на корпусе.

Немного описания:
CZ1 — Длительность импульса на контактах центрального замка. ( электрические привода / пневматический ЦЗ). Не всегда если у вас воздушный цз нужно ставить перемычку. Всё зависит от того как это будет устанавливаться.
CZ2 — Моргание поворотов при открытии двери. (Моргать / не моргать).
CZ3 — Функция Anti- hijack (включать / не включать). Что такое не знаю, не проверял.
CZ4 — Авто постановка на охрану. (Выключена / включена).

Информация ни откуда не скопирована, а напечатана собственноручно, так что при копировании ссылка сюда обязательна.

Дополню немного.
В комментариях говорилось что могут быть немного другое расположение перемычек программирования. Так что если с Вашей сигналкой есть инструкция, загляните и в неё. И если есть что-нибудь интересное по теме пишите в комментариях, может кому пригодится. Спасибо за информацию!

Из комментариев:
Kodix
На одной и той же модели сигналки логика джемперов может отличаться. Сигналка JVC CD021 на плате. В инструкции отличается положение пары перемычек

Изменены положения джамперов Автопостановки и Anti- hijack.

Если есть что-нибудь интересное по этой теме пишите в комментариях, может кому пригодится.
Спасибо за информацию!