Danfoss vlt 6000 hvac инструкция

• Contents

• Table of Contents

• Bookmarks

Summary of Contents for Danfoss VLT 6000 HVAC

• VLT ® 6000 HVAC Programming ■ Quick Menu The QUICK MENU key gives access to 12 of the most important setup parameters of the drive. After programming, the drive will, in many cases, be ready for operation. The 12 Quick Menu parameters are shown in the table below. A complete description of the function is given in the parameter sections of this manual. Quick Menu Parameter Description Item Number Name 1 001 Language Selects language used for a

• VLT ® 6000 HVAC [QUICK MENU] gives access to the parameters used for the Quick menu. It is possible to switch between the Quick menu and the Extend menu modes. [EXTEND MENU] gives access to all parameters. It is possible to switch between the Extend menu and the Quick menu modes. [CHANGE DATA] is used for changing a setting selected either in the Extend menu or the Quick menu mode. [CANCEL] is used if a change of the selected parameter is not to be carried out. [OK] is us

• VLT ® 6000 HVAC ■ Changing data Regardless of whether a parameter has been selected under the Quick menu or the Extended menu, the procedure for changing data is the same. Pressing the [CHANGE DATA] key allows change of the selected parameter, and the underlining in line 4 will flash on the display. The procedure for changing data depends on whether the selected parameter represents a numerical data value or a functional value. If the chosen parameter re

• VLT ® 6000 HVAC Installation local safety regulations are complied with. In the case of an earth fault, a DC content may develop in the faulty current. Never use ELCB relays, type A, since such relays are not suitable for DC fault currents. If ELCB relays are used, this must be: • Suitable for protecting equipment with a direct current content (DC) in the faulty current (3-phase bridge rectifier) • Suitable for power-up with short charging

• VLT ® 6000 HVAC ■ Contents Introduction to HVAC ………………………………………………………………………… 2 Safety regulations …………………………………………………………………………………….. 2 Warning against unintended start ………………………………………………………………… 2 Installation ………………………………………..

• VLT ® 6000 HVAC ■ High voltage warning The voltage of the frequency converter is dangerous whenever the equipment is connected to mains. Incorrect installation of the motor or the frequency converter may cause damage to the equipment, serious personal injury or death. Consequently, the instructions in this Design Guide, as well as national and local safety regulations, must be complied with. Touching the electrical parts may be fatal — even after disconnection from mains: Using VLT 6002-6005, 200-240 V wait at leas

• VLT ® 6000 HVAC Compact IP 20 and NEMA 1 VLT 6016 — 6027 380 — 460 V VLT 6006 — 6011 200 — 240 V VLT 6016 — 6027 525 — 600 V Compact IP 20 and NEMA 1 VLT 6032 — 6042 380 — 460 V VLT 6016 — 6022 200 — 240 V VLT 6032 — 6042 525 — 600 V Compact IP 20 and NEMA 1 VLT 6052 — 6122 380 — 460 V VLT 6027 — 6032 200 — 240 V VLT 6052 — 6072 525 — 600 V Compact IP 54 VLT 6102 — 6122 380 — 460 V Compact IP 54 VLT 6002 — 6011 380 — 460 V VLT 6002 — 6005 200 — 240 V Compact IP 54 VLT 6016 — 6032 380 — 460 V VLT 6006 —

• VLT ® 6000 HVAC Introduction to HVAC 175HA490.11 Warning: Touching the electrical parts may be fatal — even after the equipment has been disconnected from mains. Using VLT 6002 — 6005, 200-240 V: Wait at least 4 minutes Using VLT 6006 — 6062, 200-240 V: Wait at least 15 minutes Using VLT 6002 — 6005, 380-460 V: Wait at least 4 minutes Using VLT 6006 — 6072, 380-460 V

• VLT ® 6000 HVAC ■ Status messages Status messages appear in the 4th line of the display — see example below. The left part of the status line indicates the active type of control of the frequency converter. The centre part of the status line indicates the active reference. The last part of the status line gives the present status, e.g. «Running», «Stop» or «Stand by». 175ZA701.10 40.0Hz 80.0% 5.08A 2.15kW SETUP 1 AUTO REMOTE RUNNING HAND LOCAL STOP LOCAL STOPRAMPING HAND JOGGING .

• VLT ® 6000 HVAC ■ List of warnings and alarms The table gives the different warnings and alarms and indicates whether the fault locks the frequency converter. After Trip locked, the mains supply must be cut and the fault must be corrected. Reconnect the mains supply and reset the frequency converter before being ready. A Trip can be reset manually in three ways 1. Via the control key [RESET] 2. Via a digital input 3. Via serial communication In ad

• VLT ® 6000 HVAC ■ Mechanical installation Please pay attention to the requirements that apply to integration and field mounting kit, see the below list. The information given in the list must be observed to avoid serious damage or injury, especially when installing large units. The frequency converter must be installed vertically. The frequency converter is cooled by means of air circulation. For the unit to be able to release its cooling air, the minimum distance over and below the unit must be