Dmx master ca 1612j инструкция на русском

Предложите, как улучшить StudyLib

(Для жалоб на нарушения авторских прав, используйте

другую форму
)

• Technical Specification

  Power Input ………………………………DC 9V , 300 mA
  min. DMX Input ……………………………………….3 pin
  male XLR DMX Output
  …………………………………………3 pin female XLR
  MIDI Signal …………………………………5 pin standard
  interface Audio Input ………………………By built-in
  microphone or line in Dimensions
  ………………………………………….. 482x132x73mm
  Weight(appro.)
  ……………………………………………………. 2.5
  kg

  Innovation , Quality , Performance

  DMX MASTER Professional Lighting Technology

  User Guide Please read these instructions carefully before
  use

• 2B

  Note

  CONTENTS 1. Features.. Page 1

  2. General Instructions.. Page 2

  3. Overview.. Page 3

  3-1. Front View. Page 3

  3-2. Rear View. Page 6

  4. Operation Guide.. Page 6

  4-1 Program Enable… Page 7

  4-2 Programming Scenes….. Page 8

  4-2.1Scene Editing. Page 10

  4-2.2 Scanner Copy… Page 11

  4-2.3 Scene Copy… Page 12

  4-2.4 Delete a Scene. Page 13

  4-2.5 Delete all Scenes. Page 13

  4-2.6 Bank Copy….. Page 14

  4-3 Programming Chase… Page 15

  4-3.1 Program a bank of scenes into a Chase…… Page 15

  4-3.2 Add a Step. Page 16

  4-3.3 Delete a Step…. Page 17

  4-3.4 Delete a Chase….. Page 17

  4-3.5 Delete all Chases. Page 18

  4-4 Assign/Reverse DMX channel… Page 18

  4-4.1 Assign DMX channel Page 18

  4-4.2 Reverse DMX channel. Page 20

  4-4.3 Fade Time/Assign Fade Time…. Page 21

  4-4.4Delete a scanner of DMX. Page 22

  4-4.5 Clear all DMX channels… Page 22

  4-4.6 Display DMX channel… Page 22

  4-5 Running Scenes.. Page 23

  4-5.1 Manual Mode Page 23

  4-5.2 Auto Mode. Page 24

  4-5.3 Music Mode… Page 25

  4-6 Running Chases.. Page 26

  4-6.1 Manual Mode Page 26

  4-6.2 Auto Mode. Page 26

  4-6.3 Music Mode… Page 27

  4-7 MIDI Operation. Page 27

  4-7.1 MIDI Channel Setting.. Page 27

  4-7.2 Implementation. Page 28

  4-8 Send File Dump… Page 29

  4-9 Receive File Dump Page 29

• 3B

  1. Features

  A. 192 DMX channels.

  B. 12 scanners of 16 DMX channels.

  C. 30 banks of 8 programmable scenes.

  D. 6 chases of 240 programmed scenes from 30 banks

  E. 8 faders for manual control

  F. All data can be sent or received between two units

  G. Auto programs(scenes and chases) under control by Speed(or
  Tap Sync)

  and Fade Time sliders

  H. Fade Time/Assign Fade Time

  I. The scanners under control by Pan and Tilt jog wheels

  J. Fine adjustment of the Pan and Tilt

  K. Reverse DMX channels causing the faders to control the output
  reversely

  L. Preview assigned or reversed DMX channels

  M. 8 CH./16 CH. mode for Assigned or Reversed DMX channels

  N. Blackout master

  O. Manual override

  P. Built-in microphone for Music triggering

  Q. MIDI control over banks, chases and Blackout

  R. LCD display

  S. DMX polarity select

  T. Power failure memory

  Page 1

  EC Declaration of Conformity

  We declare that our products (lighting equipments) comply with
  the following

  specification and bears CE mark in accordance with the provision
  of the

  Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

  EN55014-2: 1997 A1:2001, EN61000-4-2: 1995;
  EN61000-4-3:2002;

  EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,

  EN61000-4-11: 1994.

  &

  Harmonized Standard

  EN60598-1: 2000+ALL:2000+A12:2002

  Safety of household and similar electrical appliances

  Part 1 : General requirements

  Page 30

• 4B

  4-8 Send File Dump NOTE You must set up proper connection before
  you can send or receive the file dump.

  1. With the power off, press and hold down the Scanner
  buttons

  2, 3 and Scene button 1 at a time.

  2. Apply the power again while pressing these three buttons,

  the LCD shows «TRANSMIT» indicating this unit is ready to

  send the file dump.

  3. Press the Scene buttons 7 and 8 at a time to send the
  file

  dump.

  4. During the course of sending, if malfunction occurs, the

  sending will be interrupted and the LCD shows «ERROR».

  4-9 Receive File Dump

  1. With the power off, press and hold down the Scanner
  buttons

  8, 9 and Scene button 2 at a time. 2. Apply the power again
  while pressing these three buttons,

  the LCD shows «RECEIVE» indicating this unit is receiving
  the

  file dump.

  3. When receiving is over, this unit will return to the normal
  mode.

  Page 29

  2. General Instructions

  Please read the user manual carefully, as it includes important
  information regarding details of

  operation, maintenance, and technical data. Keep this manual
  with the unit for future consult.

  WARNINGS

  DO NOT make any inflammable liquids, water or metal objects
  enter the unit. Should any liquid be spilled on the unit,
  DISCONNECT the power supply to the

  unit immediately.

  STOP using the unit immediately In the event of serious
  operation problems and either contact your local dealer for a check
  or contact us directly.

  DO NOT open the unit—there are no user serviceable parts
  inside. NEVER try to repair the unit yourself. Repairs by
  unqualified people could cause

  damage or faulty operation. Contact your nearest dealer.

  CAUTIONS

  This unit is NOT intended for home use. After having removed the
  packaging check that the unit is NOT damaged in any

  way. If in doubt, DON’T use it and contact an authorized
  dealer.

  Packaging material (plastic bags, polystyrene foam, nails, etc.)
  MUST NOT be left within children’s reach, as it can be
  dangerous.

  This unit must only be operated by adults. DO NOT allow children
  to tamper or play with it.

  NEVER use the unit under the following conditions: In places
  subject to excessive humidity. In places subject to vibrations or
  bumps. In places with a temperature of over 45 C/113 F or less than
  2 C/35.6 F.

  Protect the unit from excessive dryness or humidity (ideal
  conditions are between 35% and 80%).

  DO NOT dismantle or modify the unit.

  Page 2

• 5B

  3. Overview

  3-1. Front View

  CA-1612J

  CA-1612W

  Page 3

  2. Use the Bank Up/Down button to select the DMX channel

  01-16 to assign to MIDI channel.

  3. Press and hold down the MIDI/Rec button for three seconds

  to store your setting and to deactivate MIDI setting.

  To cancel your setting, tap any other button (except Bank

  Up/Down buttons) to exit MIDI mode.

  4-7.2 Implementation This unit receives Note On signals, which
  enables to run 15 banks(01-15) of scenes and 6 chases of scenes. In
  addition, blackout function can be activated by MIDI signal. BANK
  NOTE NUMBER FUNCTION Bank 1 00 to 07 Turn on or off Scenes 1-8 of
  Bank 1 Bank 2 08 to 15 Turn on or off Scenes 1-8 of Bank 2 Bank 3
  16 to 23 Turn on or off Scenes 1-8 of Bank 3 .. . Bank 14 104 to
  111 Turn on or off Scenes 1-8 of Bank 14 Bank 15 112 to 119 Turn on
  or off Scenes 1-8 of Bank 15 Chase 1 120 Turn on or off Chase 1
  Chase 2 121 Turn on or off Chase 2 Chase 3 122 Turn on or off Chase
  3 Chase 4 123 Turn on or off Chase 4 Chase 5 124 Turn on or off
  Chase 5 Chase 6 125 Turn on or off Chase 6

  126 Blackout Page 28

• 6B

  3. Use the Speed slider(or Tap Sync) and Fade Time slider to

  adjust the chase to your desired effects.

  You may select several chases at a time, the chases will run

  in sequence that you select the chases.

  4-6.3 Music Mode

  1. Tap the Music/Bank Copy button to activate Music mode,
  the

  Music LED lights indicating Music mode is active.

  2. Select your desired chase by tapping one of the six Chase

  buttons, the chase will be triggered by the music rhythms.

  You may select several chases at a time.

  4-7 MIDI Operation 4-7.1 MIDI Channel Setting

  1. Press and hold down the MIDI/Rec button for three
  seconds,

  the LCD show the MIDI channel of last time.

  Page 27

  1. Scanner Buttons(1-12) 12 scanners of 16 DMX channels &
  fader control

  Scanners DMX channels Fader control LED 1 1-16 Off Off 2 17-32
  Off Off 3 33-48 Off Off 4 49-64 Off Off 5 65-80 Off Off 6 81-96 Off
  Off 7 97-112 Off Off 8 113-128 Off Off 9 129-144 Off Off

  10 145-160 Off Off 11 161-176 Off Off 12 177-192 Off Off

  Scanners DMX channels Fader control LED 1 1-16 On On 2 17-32 On
  On 3 33-48 On On 4 49-64 On On 5 65-80 On On 6 81-96 On On 7 97-112
  On On 8 113-128 On On 9 129-144 On On

  10 145-160 On On 11 161-176 On On 12 177-192 On On

  Press a scanner button to turn on manual fader control. Press
  the scanner button

  again to turn off fader control. The LED besides the button
  lights or goes out to indicate this selection. Page 4

• 7B

  2. Scene Buttons Press the scene buttons to load or stored your
  scenes. There are a maximum of 240 programmable scenes.

  3. Faders These faders are used to control the intensity of
  channel 1-8 or channel 9-16 depending upon the selected page.

  4. Page Select Button Used to select page between Page A(1-8)
  and Page B(9-16). 5. Fog Machine Button Activates Fog Machine . 6.
  Speed Slider Used to adjust the chase speed within the range of 0.1
  second

  to 10 minutes. 7. Fade Time Slider Used to adjust the fade time.
  Fade time is the amount of time it takes for a scanner(or scanner)
  to move from one position to another, for the dimmer to fade in or
  fade out. 8. LCD Display Shows the current activity or programming
  state. 9. Pan Wheel This jog wheel is used to control the pan of
  the scanner or for programming. 10. Tilt Wheel This jog wheel is
  used to control the Tilt of the scanner or for programming. 11.
  Program Button Activates Program mode. 12. MIDI/Rec Used to control
  MIDI operation or to record programs. 13. Auto/Del Activates Auto
  mode or to delete scenes or chases. 14. Music/Bank Copy Activates
  Music mode or to copy a bank of scenes 15. Bank Up/Down Press the
  Up/Down button to select from 30 banks. 16. Tap/Display Used to
  create a standard beat or to change the value mode between % and
  0-255. 17. Blackout Button Tap to momentarily pause whole output.
  18. Chase Buttons(1-6) These buttons are used for activating the
  chase of programmed scenes. 19. Fine Button When Fine is on, the
  Pan or Tilt wheel will control the scanner in the smallest
  increment. 20. Mode Button Pressing Fine and Mode buttons allows to
  activate Assign or Reverse mode.

  Page 5

  4-6 Running Chases You must program scenes before you can run
  chases. 4-6.1 Manual Mode

  1. When the power is turned on, this unit enters Manual mode
  automatically.

  2. Select your desired chase by tapping one of the six Chase
  buttons. A second tap of this

  button will deactivate this function.

  3. Use the Fade Time slider to adjust the current scenes to your
  desired effects.

  4. Use the Bank Up/Down button to run the chase step by
  step.

  4-6.2 Auto Mode

  1. Tap the Auto/Del button to activate Auto mode.The Auto
  LED

  lights indicating Auto mode is active.

  2. Select your desired chase by tapping one of the six Chase

  buttons. A second tap of this

  button will deactivate this function.

  Page 26

• 8B

  Hints: The Tap Sync button is used to set the speed by tapping
  the button several

  times, the last two taps will define the speed with a maximum of
  10 minutes.

  Tap Sync will override any previous setting of the Speed slider
  unless the slider

  is moved again.

  4. Tap the Auto/Del button again to exit Auto mode .

  4-5.3 Music Mode

  1. Tap the Music/Bank Copy button to activate Music mode.
  The

  Music LED lights indicating Music mode is active.

  2. Use the Bank Up/Down button to select the bank that holds

  the scenes you wish to run. The scenes you’ve selected will

  chase in a sequential order according to the music rhythms

  detected by the built-in microphone. 3. Tap the Music/Bank Copy
  button again to exit Music mode.

  Page 25

  3-2 Rear View

  1. AUDIO IN 0.1V~1Vp-p. 2. MIDI IN Receives MIDI data. 3. DMX
  Polarity Select Used to select DMX polarity. 4. DMX Out This
  connector sends your DMX value to the DMX

  scanner or DMX pack.

  5. DMX In This connector accepts your DMX input signals. 6. Fog
  Machine Connector This connector is used to plug in the Fog
  Machine. 7. DC Input DC 9 -12V, 300mA min. 8. Power Switch This
  switch turns On/Off the power.

  Fog machine diagram

  Page 6

  A

• 9B

  4. Operation Guide General This unit allows you to program 12
  scanners of 16 DMX channels, 30 banks of 8

  programmable scenes, 6 chases of 240 programmed scenes using 8
  faders and

  other function buttons. With the use of two jog wheels, you may
  easily control the

  Pan or Tilt of the scanners. To tailor your special effect
  lighting, this unit enables

  you to Assign or Reverse the DMX channels. In addition, two
  units can set up

  communication so that they can send or receive file dump.
  Display Information The LCD Display contains a maximum of 2×8
  characters. LCD Display Message CHASE 5 Chase 5 is activated. STEP
  002 The 2nd step of a chase

  DATA 151 DMX value(000-255)

  SP: 1M36S The current speed is 1 minute and 36 seconds

  TP: 5.32S The time of the last two taps is 5.32 seconds FT:
  10.5S Fade Time is 10.5 seconds

  ASS 07 08 Assign DMX channels 7 and 8

  RES 10 13 Reverse DMX Channels 10 and 13

  SN 6 Scene 6

  BK 03 Bank 03

  4-1 Program Enable

  When the power is turned on, this unit enters

  Manual mode automatically.

  Press the Program button for three seconds to

  activate Program mode, the LED near to this

  button lights indicating Program in active.

  Page 7

  4. Tap the Scene button to select the scene to run.

  4-5.2 Auto Mode This function allows you to run a bank of
  programmed scenes in a sequential loop.

  1. Tap the Auto/Del button to activate Auto mode.The Auto
  LED

  lights indicating Auto mode is active.

  2. Use the Bank Up/Down button to select a bank of scenes to

  run.

  3. After selecting the bank of scenes you wish to run, you
  can

  use the Speed slider(or Tap Sync/Display button) and Fade

  Time slider to adjust the scenes to your desired effect.

  Page 24

• 10B

  4-4.6 Display DMX channel

  1. Press the Fine and Mode buttons at a time,the Assign LED

  lights.

  2. Press the Fine and Mode buttons the second time,the
  Assign

  LED goes out and the Reverse LED lights.

  3. Tap the Scanner button that holds the Pan and Tilt
  channel,

  the LCD shows the Pan and Tilt.

  4-5 Running Scenes 4-5.1 Manual Mode

  1. When the power is turned on, this unit enters Manual mode
  automatically.This function

  allows you to run a bank of programmed scenes in a sequential
  loop.

  2. Make sure Auto and Music LEDs are both off.

  3. Use the Bank Up/Down button to select the bank that contains
  the scenes you wish to run.

  Page 23

  4-2 Programming Scenes 1. Enter Program mode.

  2. Press the Scanner button to turn on its fader control, which
  is

  indicated by the lit LED.

  You may select several scanners at a time by tapping of
  these

  Scanner buttons, so you can set several scanners at a time.

  3. Move the faders to select your desired dimmer intensity if
  you are using a dimmer.

  You can also use the two jog wheels to control the Pan or Tilt
  movement of the scanner.

  4. If necessary , you may tap the Page Select button to
  control

  the second set of 8 DMX channels.

  5. Once the scene is satisfactory, tap the MIDI/Rec button
  to

  program this scene into memory.

  6. Tap the Bank Up/Down button to select the bank you want
  to

  store your scene into. There are total 30 banks you can
  select,

  you may store up to 8 scenes into each bank.

  7. Tap the Scene button to store your scene, all LEDs and
  the

  Segment Display will flash three times briefly indicating
  this

  operation, then the LCD will show the bank and the scene

  Page 8

• 11B

  8. Repeat steps 3-7until all desired scenes have been

  programmed into memory .Tap the Scanner button again to turn

  off its fader control.To set another scanner(scanner), you
  may

  tap the corresponding Scanner button to turn on its fader
  control,

  then you may begin your programming again.

  9. If you don’t intend to continue your programming,

  press and hold down the Program button for three

  seconds to exit Program mode, the LED goes out

  indicating this selection.

  EXAMPLE: Program 8 scenes with channel 1-8 at full in sequence
  into bank 3 and assign these scenes to scanner 1.

  1. Program enable.

  2. Tap the Scanner 1 button to turn on its fader control.

  3. Tap the Page Select button to select Page A.

  4. Push Fader 1 to the top position.

  5. Tap the MIDI/Rec button.

  6. Select bank 3 using Bank Up/Down button.

  7. Tap the Scene 1 button to store the first scene.

  8. Repeat steps 4-7 until all 8 scenes have been programmed into
  bank 3.

  9. Tap the Scanner 1 button again to turn off its fader
  control.

  10. Press the Program button for 3 seconds to exit Programming
  mode.

  Page 9

  3. Press the Mode and TAP/Display buttons at a time to store

  your setting into memory.

  If you are not going to save your setting, tap the Blackout

  button to leave this operation.

  4-4.4 Delete a scanner of DMX channels

  1. Activate Assign or Reverse mode(Described in the

  sub-chater 2.2.4.1 or 2.2.4.2).

  2. Tap the Scanner button to select the scanner you wish to

  delete.

  3. Press the Mode and Auto/Del buttons at a time,all LEDs

  should flash briefly, indicating the scanner is deleted.

  4-4.5 Clear all DMX channels

  1. Turn the power off.

  2. Press the Mode and Auto/Del buttons at a time. 3. While
  pressing the two buttons, apply the power again, all

  LEDs should flash briefly,indicating all assigned or
  reversed

  DMX channel are cleared.

  Page 22

• 12B

  6. Tap the Page Select button to select Page A or Page B.

  7. While pressing the Mode button, tap the Scene button, all

  LEDs should flash briefly indicating the DMX channel is

  reversed.( Scene button 1 stands for DMX channel 1, Scene

  button 2 stands for DMX channel 2, and so on.) 8. Continue steps
  3-7 , you may reverse a maximum of 48 DMX

  channels for 12 scanners.

  4-4.3 Fade Time/Assign Fade Time

  1. With the power off, press the Mode and TAP/Display
  buttons

  at a time.

  2. Apply the power again, tap the TAP/Display button to
  change

  between Fade Time and Assign Fade Time, the LCD reads ALL CH or
  ONLY X/Y

  FD TIME FD TIME

  Page 21

  4-2.1 Scene Editing 1. Program enable.

  2. Tap the Bank Up/Down button to select the bank that

  contains the scene you wish to edit.

  3. Select the scene you want to edit by tapping its Scene
  button.

  4. Use the Faders or jog wheels to make your desired

  adjustments.

  5. Once you’ve made your changes, tap the MIDI/Rec button

  Page 10

• 13B

  6. Tap the Scene button that corresponds to the scene you’re

  editing. This will overwrite the exited scene

  NOTE: Be sure to select the same scene in steps 3 and 6,
  otherwise you may accidentally record over an exited scene.

  4-2.2 Scanner Copy This function allows you to copy the settings
  of one scanner to another.

  1. Press and hold down the Scanner button you want to copy.

  2. While holding the Scanner button, tap the Scanner button
  you

  want to copy to.

  Page 11

  4-4.2 Reverse DMX channel 1. Program enable.

  2. Press the Fine and Mode buttons the second time, the

  Reverse LED lights up indicating Reverse mode is active.

  3. Use Bank Up/Down button to change between the Pan and

  Tilt, the corresponding LED lights indicating this
  selection.

  4. Tap the Tap/Display button to change between 8 CH. and 16

  CH. mode.

  5. Tap the Scanner button to select the scanner.

  Page 20

• 14B

  4. Tap the Tap/Display button to change between 8 CH. and

  16 CH. mode, the LCD reads ASSXX XX or ASSXX XX X/Y X/Y 08CH
  16CH

  5. Tap the Scanner button to select the scanner.

  6. Tap the Page Select button to select Page A or Page B.

  7. While pressing the Mode button, tap the Scene button, all

  LEDs should flash briefly indicating the DMX channel is

  assigned.( Scene button 1 stands for DMX channel 1, Scene

  button 2 stands for DMX channel 2, and so on.) 8. Continue steps
  3-7 , you may assign a maximum of 48 DMX

  channels for 12 scanners. Page 19

  4-2.3 Scene Copy 1.Program enable.

  2. Tap the Bank Up/Down button to select the bank that

  contains the scene you wish to copy.

  3. Select the scene you want to copy by tapping its Scene

  button

  4. Tap the Bank Up/Down button to select the bank you wish
  to

  copy the scene to.

  5. Tap the MIDI/Rec button.

  Page 12

• 15B

  6. Tap the Scene button you wish to copy the scene to.

  4-2.4 Delete a Scene 1. Tap the desired Scene button to select
  the scene you wish to delete

  2. Press and hold down the Auto/Del button.While holding
  down

  the Auto/Del button, tap the Scene button that stores the
  scene

  you wish to delete.

  4-2.5 Delete all Scenes This function will reset all DMX channel
  to 0 output.

  1. With the power off, press and hold down the Program and

  Bank Down buttons at a time.

  2. Apply power again, all scenes should be cleared.

  Page 13

  2. Press and hold down the Auto/Del button. Tap the Chase

  button while holding down the Auto/Del button, all LEDs will

  flash three times briefly indicating this chase has been
  deleted.

  4-3.5 Delete all Chases

  1. With the power off, press and hold down the Auto/Del and

  Bank Down buttons at the same time.

  2. Apply the power again.

  4-4 Assign/Reverse DMX channel 4-4.1 Assign DMX channel

  1. Program enable.

  2. Press the Fine and Mode buttons at a time,the Assign LED

  lights up indicating Assign mode is active.

  3. Use Bank Up/Down button to change between the Pan and

  Tilt, the corresponding LED lights indicating this
  selection.

  Page 18

• 16B

  7. Tap the MIDI/Rec button again , all LEDs will flash three

  times briefly indicating the new step has been inserted into
  this

  chase.

  4-3.3 Delete a Step 1. Program enable.

  2. Select the chase that contains the step you wish to
  delete.

  3. Tap the Tap/Display button, the LCD shows the current
  step.

  4. Tap the Bank Up/Down button to scroll to the step you wish
  to

  delete.

  5. Tap the Auto/Del button to delete the step, all LEDs will
  flash

  three times briefly indicating that the step has been
  deleted.

  4-3.4 Delete a Chase

  1. Select the chase you wish to delete.

  Page 17

  4-2.6 Bank Copy 1. Program enable.

  2. Tap the Bank Up/Down button to select the bank you wish
  to

  copy.

  3. Tap the MIDI/Rec button.

  4. Tap the Bank Up/Down button to select the bank you wish
  to

  copy to.

  5. Tap the Music/Bank Copy button, all LEDs will will flash
  three

  times briefly indicating the function has been completed.

  6. Press the Program button for three seconds to exit

  Programming mode.

  Page 14

• 17B

  4-3 Programming Chase You must program scenes before you can
  program chases, this function allows you to store up to 240 scenes
  into one chase.

  1. Program enable.

  2. Tap the Chase button to select the chase to program. Each

  time you can select a chase only.

  3. Select a desired scene from the bank that has stored

  scenes.(described in Programming Scenes)

  4. Tap the MIDI/Rec button.

  5. Repeat steps 3-4 until you’ve reached your desired
  effect.

  You may record up to 240 scenes into a chase.

  4-3.1 Program a bank of scenes into a Chase 1. Program
  enable.

  2. Select the chase using Chase buttons 1-6. 3. Use Bank Up/Down
  button to select the bank that contains

  the scenes you wish to copy.

  4. Tap the Music/Bank Copy button.

  5. Tap the MIDI/Rec Copy button, all LEDs will flash three
  times

  briefly indicating all 8 scenes in this bank have been

  programmed into this chase.

  Page 15

  4-3.2 Add a Step 1. Program enable.

  2. Select the chase you wish to add a step to.

  3. Tap the Tap/Display button, the LCD shows the current
  step.

  4. Tap the Bank Up/Down button to scroll to the step you wish
  to

  add a step after.

  5. Tap the MIDI/Rec button, the Segment Display will read
  the

  step one higher than before.

  For example, if you want to insert a step between step 3 and

  step 4, and you scroll to step 3, when you tap the MIDI/Rec

  button, the LCD will read «STEP 004».

  6. Tap the Tap/Display button again, the LCD shows the
  current

  chase, scene and bank.Create a desired scene and record it
  as

  a new step or select a programmed scene you wish to add into

  this chase.

  Hints: You may tap the Tap Sync/Display button to change the
  display mode between step and the bank.

  Page 16

Dmx master, Ca-1612 user manual, Dmx 512