Enda ec762f инструкция на русском

Read this document carefully before using this device. The guarantee will be expired by

damaging of the device if you don’t attend to the directions in the user manual. Also we don’t

accept any compensations for personal injury, material damage or capital disadvantages.

ENDA EC762F UP/DOWN COUNTER

Thank you for choosing ENDA EC762F COUNTER.

* 72x72mm sized.

* 2×6 digits display.

* Easy to use by front panel keypad.

* Counting up and down with a 2 channel inputs having 90° phase shift.

* Input frequency can be selectable.

* Prescaler factor can be adjusted between 0.001 and 99.9999.

* 6 digits Batch Counter.

* 6 digits Total Counter.

* Preset1 may depend on Preset2.

* Decimal point can be adjusted between 1. and 5. digits.

* Sensor type can be selected as PNP, NPN or Encoder.

* Double set-points control is made by 2 relays outputs.

* Output can be energized continuously or just for a time interval of 0.01

to 999.9 seconds.

* Selectable functional reset input.

* Input offset feature.

* Parameter access protection on 3 levels.

* Easy connection by removable screw terminal.

* Having CE mark according to European Norms.

Supply Voltage

230V AC +10% -20%

24V AC ±10%

9-30V DC SMPS module

TECHNICAL SPECIFICATIONS

ENVIRONMENTAL CONDITIONS

Ambient/storage temperature

Max. relative humidity

Rated pollution degree

Height

Do not use the device in locations subject to corrosive and flammable gases.

ELECTRICAL CHARACTERISTICS

Supply

230V AC +%10 -%20, 50/60Hz or 24V AC ±%10, 50/60Hz or optional 9-30V DC SMPS module.

Power consumption

Max. 7VA

Wiring

2.5mm² screw-terminal connections

Date retention

EEPROM (Min. 10 years)

EMC

EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B for the EMC standard)

Safety requirements

EN 61010-1: 2001 (pollution degree 2, overvoltage category II)

INPUTS

Count inputs (CP1, CP2)

2 channels (Max. 7500Hz, 5V to 30V pulse)

Frequency (Hz)

25, 500, 1000, 2000, 5000, 7500Hz (selectable by programming)

Minimum On ans Off times

20ms for

for pulses

1ms for f=500Hz

500 s for f

250 s for

100 s for

67 s for

PNP: Positive reset (5V to 30V pulse with adjustable pulse time between 2ms and 50ms)

Reset input

NPN: GND terminal is connected to the RESET IN terminal.

OUTPUTS

Relay : 250V AC, 2A (for resistive load), NO+NC

Control output (OUT1)

Open collector output (S.S. OUT1): Max. 30V DC, 100mA.

Relay : 250V AC, 2A (for resistive load), NO+NC

Control output (OUT2)

Open collector output (S.S. OUT2): Max. 30V DC, 100mA.

12V DC, Max. 50mA (without regulation)

Auxiliary power supply

Life expectancy for relays

Mechanical 30.000.000 operation; Electrical 300.000 operation

Note : Relay and S.S.OUT outputs are in synchronization . When OUT1 relay is energized S.S. OUT1 transistor goes into saturation.

Similarly, when OUT2 relay is energized S.S. OUT2 transistor goes into saturation.

HOUSING

Housing type

Suitable for flush-panel mounting according to DIN 43 700.

Dimensions

W72xH72xD97mm

Weight

Approx. 405g (after packing)

Self extinguishing plastics

Enclosure material

While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.

Order Code

EC762F

EC762F-24AC

EC762F-24DC

0 … +50 °C/-25 … +70°C (with no icing)

80% up to 31

°C

decreasing linearly 50% at 40

According to EN 60529

Max. 2000m

f=25Hz

=1kHz

f=2kHz

f=5kHz

f=7,5kHz

EC762F

SET

ENDA

°C

.

Front panel :

IP60

Rear panel :

IP20

.

1/5

1/5

OUT1

OUT2

BATCH TOTAL

PRESET

TOTAL

RESET

PRESET UP/DOWN COUNTER

EC762F-E-04

Document’s Content and Additional Information

Share Manual

ENDA EC762F Operation & user’s manual ENDA Cash Counter Operation & user’s manual for ENDA EC762F enda-ec762f-operation-user-s-manual-5_manual.pdf 5 | Pages Preview: Document Transcription: PNP PROXIMITY SWITCH GND OUT + 12V GND + 12V A OUT B OUT ENCODER PNP PROXIMITY SWITCH PNP PROXIMITY SWITCH GND + 12V + 12V GND OUT OUT TYPICAL SENSOR CONNECTIONS TERMINAL CONNECTIONS Terminal descriptions 4 : Reset input. 5 : Solid state out2 (Max 30V 100mA … Count inputs (CP1, CP2) 2 channels (Max. 7500Hz, 5V to 30V pulse) Frequency (Hz) 25, 500, 1000, 2000, 5000, 7500Hz (selectable by programming) * 72x72mm sized. * 2×6 digits display. * Easy to use by front panel keypad. * Counting up and down with a … OUTPUT TYPES Config 2 Config 1 Reset 999,999 Preset2 Preset1 0 Out1 Out2 999,999 Preset2 Reset Preset1 0 Out1 Out2 Config 3 Reset Preset1 0 Out1 Out2 999,999 Preset2 Config 4 Reset Preset1 0 Out1 Out2 999,999 … See Details Download

Run mode

99999

The value of the parameter selected by

100000

parameter is on the display.

PrSEt1

First preset value.

See NOTE 1 for modification.

100000

PRESET

PrSEt2

Second preset value.

See NOTE 1 for modification.

150000

SET

if

key is pressed while holding

PRESET

PRG

programming mode is entered.

ýnPut

oPtýon.

PRESET

RESET

There are seven different

ýnPut

input types. A schematic diagram of

counting modes according to the input

typE

types is at the next page.

See NOTE 2 for modification.

RESET

Counting direction can be selected

Countr.

dirEct. or oPPos. A schematic

diagram of counting directions

dýr.

according to the selected input types

is at the next page.

See NOTE 2 for modification.

RESET

ýnPut

Input frequency can be selected.

See NOTE 2 for modification.

Frq.

RESET

SEnSor

Sensor type can be selected.

See NOTE 2 for modification.

tyPE

RESET

Reset

The minimum pulse duration of the

external RESET input can be selected.

Puls

See NOTE 2 for modification.

PARAMETER MODIFICATION DIAGRAM

SET

NOTE 1

Holding

key the value of the selected parameter is seen on the display. While holding

using

keys. In order to reset all the digits, first press and hold

PRESET

RESET

Selected

SET

SET

numerical

1.00000

parameter

PRESET

SET

NOTE 2

To modify non-mumerical parameters, hold

key and use

NOTE 3

To change the position of the decimal point press and hold both

inPut

CP1-UP

typE

CP2-dn

Countr.

dir.

dirEct

disP..

inPut

25

config

Frq.

Hert.

SEnSor

tyPE

nPn

rESEt

0.002

PuLS

second

outPut

conFiG.

typE

out1

ti.

000.0

out2

000.0

ti.

tot.Cr.

SET

conFiG.

diSAb.

key, the

PrSEt1.

Equ.

PrSEt1.

OutPut

oPtýon.

PRESET

RESET

There are eleven different output types. A schematic

outPut.

diagram of output types is at the next page.

See NOTE 2 for modification.

typE

Out1

energizing time can be adjusted between 000.0 and

RESET

999.9 seconds.

out1

If it is made 000.0 output is energized continuously when

PrSEt1

counter reaches

value.

tý.

See NOTE 1 for modification.

See NOTE 3 for changing the position of the decimal point.

RESET

Out2

energizing time can be adjusted between 000.0 and

out2

999.9 seconds.

If it is made 0.0, output is energized continuously when

tý.

PrSEt 2

counter reaches

value.

See NOTE 1 for modification.

See NOTE 3 for changing the position of the decimal point.

RESET

diSAb.

= Totalizer counter parameter becomes active.

tot.Cr.

inPut

= Counter input is selected as Totalizer counter input.

Countr.

conFýG.

inPut

out1

= Totalizer counts

.

out1

inPut

= Totalizer counts

out2

.

out2

RESET

See NOTE 2 for modification.

PrSEt1.

PrSEt1

= Output is energized when counter reaches

Equ.

Pr2.Sub.

PrSEt2

= The difference between

Pr1.

value of

PrSEt1

‘. It means

Now, o

utput is energized when counter reaches

See NOTE 2 for modification.

SET

key, the value of the selected parameter can be changed by

SET

key. And then, press both

and

SET

SET

1.00000

1.00000

1.01000

PRESET

keys.

RESET

SET

and

keys for 0.6 sec.

PRESET

CP1-UP

CP1-UP

CP1-UP

UP

UP-dn

UP-dn

Ph-4

CP2-UP

CP2-Gt.

CP2.dir.

Ph-1

Ph-2

oPPoS.

500

5000

1000

2000

7500

Hert.

Hert.

Hert.

Hert.

Hert.

PnP

Encod.

0.005

0.010

0.020

0.050

second

second

second

second

conFiG.

conFiG.

conFiG.

conFiG.

conFiG.

conFiG.

1

2

3

4

5

6

7

…………

999.9

………….

999.9

inPut

inPut

inPut

Countr.

out1

out2

Pr2.Sub.

Pr1.

dýsP.

oPtýon.

RESET

Decimal point can be adjusted between 1. and 5. digits.

dEcý.

If desired, decimal point is not included.

Poýnt

See NOTE 2 for modification.

Calibration (Prescaler) value can be adjusted between

RESET

0.00001 and 99.9999. Counter multiplies the number of

dýsP.

pulses by the prescaler value and the result is displayed

on the screen.

CAL.

See NOTE 1 for modification.

See NOTE 3 for changing the position of the decimal point.

RESET

offset value can be adjusted between 0 and 500000.

oFFSEt

It means counter starts counting from the offset value

dAtA

when it is reset.

See NOTE 1 for modification.

RESET

Countr.

= Upper display shows counting value,

dýsP.

PrSEt1

lower display shows

out

Countr.

=

Upper display shows counting value,

PrSEt2

lower display shows

Countr.

=

Upper display shows counting value,

bAtch

lower display shows

bAtch

=

Upper display shows

PrSEt2

lower display shows

PrSEt1

value.

PrSET1

=

Upper display shows

PrSEt1

and

becomes the new

bAtch

lower display shows

PrSEt1 (new) = PrSEt2 PrSEt1(old)

—

totAL.h

PrSEt1(new)

=

Upper display shows

value.

totAL.L

value,

lower display minimum

See NOT 2 for modification.

keys together.

RESET

SET

1.00000

RESET

3/5

dEci.

Point

0

diSP.

CAL.

0.00001 ………….

oFFSEt

dAtA

0

diSP.

Countr.

config

PrSEt1

SECUr.

codE

1111

inP.opt

SECUR.

nonE

out.opt.

conFiG.

conFiG.

conFiG.

conFiG.

SECUR.

bAtch

nonE

8

9

10

diS.opt.

SECUR.

nonE

Count.

rESEt

no

totAL.

rESEt

no

bAtch

rESEt

no

dEFAuL.

SEt.

no

SECUr.

oPtýon.

PRESET

RESET

SECUr.

codE

RESET

ýnP.opt.

SECUR.

RESET

out.opt.

SECUR.

RESET

dýs .opt.

PrSEt1

value .

SECUR.

PrSEt2

value.

RESET

bAtch

value.

Count.

bAtch

value,

PrSEt2

rESEt

value.

PrSEt1

value,

bAtch

value.

RESET

totAL

maximum

counter

totAL

totAL

counter value.

rESEt

RESET

bAtch

rESEt

RESET

dEfaul.

Set.

0.0

………….

0.00000

99.9999

…………..

500000

Countr.

bAtch

PrSEt1

totAL.h

Countr.

bAtch

PrSEt2

bAtch

totAL.L

PrSEt2

Prog.

Prog.

yES

no

Prog.

Prog.

no

yES

Prog.

Prog.

no

yES

PAnEL

rESEt

reset

rESEt

inPut

both

PAnEL

rESEt

PAnEL

rESEt

yES

PRESET

Access code for entering security option menu.

This parameter should be 1111.

See NOTE 2 for modification.

nonE

= No menu is seen.

= Menu is seen but can not be programmed.

Prog.

no

Prog.

= Menu is seen and programming is possible.

yES

See NOT 2. for modification.

nonE

= No menu is seen.

= Menu is seen but can not be programmed.

Prog.

no

Prog.

= Menu is seen and programming is possible.

yES

See NOT 2. for modification.

nonE

= No menu is seen.

= Menu is seen but can not be programmed.

Prog.

no

= Menu is seen and programming is possible.

Prog.

yES

See NOT 2. for modification.

no

= Counter can not be reset.

PAnE.

=

Counter can be reset by

key.

reSEt

RESET

reSEt

= Counter can be reset by the RESET input.

inPut.

reset

= Both RESET input and the

key can

both

be used for resetting.

RESET

See NOTE 2. for modification.

no

=

totAL

counter

can not be reset.

PAnEL

totAL

=

counter can be reset by

key.

rESEt

RESET

See NOTE 2. for modification.

no

batch

=

counter

can not be reset.

PAnEL

batch

=

counter can be reset by

key.

rESEt

RESET

See NOTE 2. for modification.

While leaving the programming mode,

no

= All the modifications are saved.

Yes

= Default values are set to parameters.

See NOTE 2. for modification.

EC762F-E-04

• Home
• Brands
• ENDA Manuals
• Cash Counter
• ENDA EC762F

1 docs – User Manuals, Help Guides and Specs – for the ENDA EC762F product are present in our data base.

Product Types: ENDA Recording Equipment ENDA Timer ENDA Inverter ENDA Measuring Instruments ENDA Thermostat ENDA Touch Panel ENDA Temperature Controller ENDA Cash Counter ENDA Controller ENDA Control Panel

Tips for Finding Manuals:

This web-page provides a list of 1 accessible operating manuals and information books describing ENDA EC762F.
All manuals and instructions for ENDA EC762F are introduced in an easy-to-use PDF format and may be gratuitously downloaded or looked through directly from the site.

The page offers the following types of manuals: Cash Counter.

Helpful hints: While selecting a necessary guide for ENDA EC762F one should pay special attention to the type of the document.
We try to supply you with the fullest possible set of papers we or our users are able to find. These may be overviews and specifications of the device, mounting and installing instructions, the unit operating rules and maintenance regulations and much more.

Haven’t found a required manual for your ENDA EC762F?

Check in a while. We update our guides collection and add new documents on a daily basis for you to be always able to find the very paper you need on our web-site. In case you own a directory or an instruction for ENDA EC762F, which is absent on our site, and you’d like to share it with the public, please send it to us as a scanned copy or a PDF file, and we’ll definitely place it on our page while providing your name as a supplier of the doc. Lots of our users will be grateful for your assistance!