-
Contents
-
Table of Contents
-
Troubleshooting
-
Bookmarks
Quick Links
CONTROL SETPOINT
PROGRAMMER
ENG
Installation and operation
handbook
Related Manuals for Eurotherm Invensys 2408
Summary of Contents for Eurotherm Invensys 2408
-
Page 1
CONTROL SETPOINT PROGRAMMER Installation and operation handbook… -
Page 2
“This product is covered by one or more of the following US Patents: 5,484,206; Additional patents pending. PDS and INSTANT ACCURACY are trademarks of Eurotherm.” Issue 10 of this handbook applies to software version 4. Issue 10.0 Nov-04 Applies to 2408 and 2404 controller software version 4.0… -
Page 3
DeviceNet Communications Handbook part no. HA027506 which includes the parameter address map. • Profibus Communications Handbook part no. HA026290 • EMC (Electromagnetic Compatibility) Installation Guide, part no. HA025464 These are available on www. eurotherm.co.uk. Issue 10.0 Nov-04 Applies to 2408 and 2404 controller software version 4.0… -
Page 4: Chapter 1 Installation
Chapter 1 INSTALLATION Terminal covers Sleeve Ratchets Display screen Label Panel retaining clips Latching ears Panel sealing gasket Figure 1-1 2408 1/8 DIN controller Sleeve Terminal covers Ratchets Display screen Label Panel retaining clips Latching ears Panel sealing gasket Figure 1-2 2404 1/4 DIN controller…
-
Page 5
OP 1 OP2 cut-out 92 x 45mm 96mm 3.78in +0.8 +0.6 3.62×1.77in +0.03 +0.02 AUTO HOLD Figure 1-3 Outline dimensions of Model 2408 controller 10mm 38mm (0.4in) (1.5in) Recommended minimum spacing (Not to of controllers scale Outline dimensions Model 2404 150mm 96mm 5.91in… -
Page 6: Mechanical Installation
Installation INTRODUCTION Models 2408 and 2404 are high stability, temperature or process controllers with self and adaptive tuning. They have a modular hardware construction which accepts up to three plug- in Input/Output modules and two interface modules to satisfy a wide range of control requirements.
-
Page 7
Installation and Operation Handbook NEW SLEEVE DESIGN MKIII From Jan-03 an improved design of 1/8 DIN long sleeve is shipped with all new 2408 controllers and indicators. (The month and year of manufacture are shown in the last two pairs of digits of the instrument serial number). -
Page 8: Electrical Installation
− − Figure 1-5 Rear terminal layout − Model 2408 * The ground connection is provided as a return for internal EMC filters. It is not required for safety purposes, but must be connected in order to satisfy EMC requirements.
-
Page 9
20 − 29Vac/dc Low voltage supply Model 2404 rear terminal layout Ground Line 85 to 264Vac Neutral Ground* Input 1 Input 2 Common Alarm relay RTD/Pt100 − − Figure 1-6 Rear terminal layout − Model 2404 2408 and 2404 Controller… -
Page 10
PDS 1 mode uses a logic output module to control aTE10S solid state relay and provides a load failure alarm. PDS 2 mode uses a logic output module to control a TE10S solid state relay, provide load/SSR failure alarms, and read back the load current for display on the controller. 2408 and 2404 Controller… -
Page 11
(BUT NOT THE TRIAC) by breaking the PCB track that runs crosswise, adjacent to the edge connectors of the module. This can be done by inserting the blade of a small screwdriver into one of the two slots that bound it, and twisting. 2408 and 2404 Controller… -
Page 12
Triple logic input and output modules — see ratings on the next page Triple contact input Input 1 Input 2 Input 3 Common Triple logic input Input 1 Input 2 Input 3 Common Triple logic output Output 1 Output 2 Output 3 Common Program events 2408 and 2404 Controller… -
Page 13
>28KΩ input resistance OFF state voltage >14Vdc ON state <100Ω resistance ON state voltage <1.0Vdc Triple logic output (current sourcing) OFF state output 0 to 0.7Vdc. ON state output 12 to 13Vdc, at up to 8mA. 1-10 2408 and 2404 Controller… -
Page 14
Installation COMMUNICATION MODULES 1 AND 2 All 2408 and 2404 controllers can be fitted with up to two plug-in communications modules. Only one of the two modules can be for serial communications and this will normally be installed in position COMMS 1 (although it is possible to install the serial communications module in position COMMS 2. -
Page 15
All resistors are 220 ohm 1/4W carbon composition. Local grounds are at equipotential. Where equipotential is not available wire into separate zones using a galvanic isolator. Use a repeater (KD845) for more than 32 units. Figure 1-9 EIA-485 wiring 1-12 2408 and 2404 Controller… -
Page 16
• 2 fuses or circuit breakers to protect the bus from excessive current which could damage the cable and connectors. • The earth connection, HF, to be connected to the main supply earth terminal. 2408 and 2404 Controller 1-13… -
Page 17
2400 Controller Network Supply 24Vdc ( +1%) 250mV p-p Ripple (SLAVE) Address N+1 * Fit 121! resistor to last instrument in the chain Daisy chain to further instruments To configure DeviceNet Communications see Chapter 6. 1-14 2408 and 2404 Controller… -
Page 18
Controllers supplied with model numbers 2408f and 2404f are fitted with ProfiBus communications modules fitted in the H slot. Further details of ProfiBus communications is given in Appendix E and the ProfiBus Communications handbook part number HA026290. This handbook can be downloaded from www.eurotherm.co.uk. Station 1 Not connected… -
Page 19: Typical Wiring Diagram
1A(T) Logic heating output Triac cooling output Heating power fuse (load dependent) − Solid State Relay * Heater Cooling Solenoid Fig 1-10 Typical wiring diagram, Model 2408 Controller For logic drive capability see following chart:- 1-16 2408 and 2404 Controller…
-
Page 20
TC1027 TE200S TC2000 RS3D Standard Multi- Logic V Logic Logic Logic drive Logic 2S 3P 1S2P 6S 1P 3S 3P 3S 3P 3S 1P 4S 2P Triple 4S 1P 2S 1P 2S 1P logic 2408 and 2404 Controller 1-17… -
Page 21
+ + + + RTD/Pt100 + + + + Input + + + + Motor Module Feedback Potentiometer − − − − − − − − − − − − (Optional) Fig 1-11 Motorised valve connections 1-18 2408 and 2404 Controller… -
Page 22
This chapter has nine topics: • FRONT PANEL LAYOUTS • BASIC OPERATION • OPERATING MODES • AUTOMATIC MODE • MANUAL MODE • PARAMETERS AND HOW TO ACCESS THEM • NAVIGATION DIAGRAM • PARAMETER TABLES • ALARMS 2408 and 2404 Controller… -
Page 23
Run/Hold HOLD Manual mode Program in Hold Page Scroll Down Button Button Button Button Figure 2-1 Model 2408 front panel layout 2404 2404 Output 2 Output 1 OP 1 OP 2 OP 1 Upper readout Lower readout Remote setpoint/ Setpoint 2… -
Page 24
Press to select a new parameter in a list. Down button Press to decrease a value in the lower readout. Up button Press to increase a value in lower readout. Figure 2-3 Controller buttons and indicators 2408 and 2404 Controller… -
Page 25: Basic Operation
If the controller detects an alarm condition, it flashes an alarm message in the Home display. For a list of all the alarm messages, their meaning and what to do about them, see Alarms at the end of this chapter. 2408 and 2404 Controller…
-
Page 26: Operating Modes
Two other modes are also available: • Remote Setpoint mode, in which the setpoint is generated from an external source. In this mode, the REM light will be on. • Programmer mode which is explained in Chapter 5, Programmer Operation. 2408 and 2404 Controller…
-
Page 27: Automatic Mode
Output Power display may access further parameters. These may be in this scroll list if the ‘Promote’ feature has been used (see Chapter 3, Edit Level). When you reach the end of this scroll list, pressing will return you to the Home display. 2408 and 2404 Controller…
-
Page 28: Manual Mode
Output Power display may access further parameters. These may be in this scroll list if the ‘Promote’ feature has been used (see Chapter 3, Edit Level). When you reach the end of this scroll list, pressing will return you to the Home display. 2408 and 2404 Controller…
-
Page 29
When you reach the end of the list, you will return to the list header. From within a list you can return to the current list header at any time can by pressing To step to the next list header, press once again. 2408 and 2404 Controller… -
Page 30
. During adjustment, single presses change the value by one digit. Keeping the button pressed speeds up the rate of change. Two seconds after releasing either button, the display blinks to show that the controller has accepted the new value. 2408 and 2404 Controller… -
Page 31
Auto PrG.t 35.0 rEL.C Lb t rEL.2 1.00 1.00 FASt rAtE diAG FF.Pb out.n SEG.n FF.tr ti.2 SEG.n SYnc tYPE FF.dv td.2 tYPE 100.0 50.0 dwEl SEG.d tYPE dwEl Figure 2-7a Navigation diagram (Part A) 2-10 2408 and 2404 Controller… -
Page 32
The shaded boxes are normally hidden in Operator level. To see all the available parameters you must select Full level. SP H See Chapter 3, Access Levels. 100.0 Figure 2-7b Navigation diagram (Part B) For additional parameters — see tables 2408 and 2404 Controller 2-11… -
Page 33
Event output states (OFF / on) (not 8-segment programmer) SYnc SYnc SYnc SYnc Segment synchronisation (no / YES) (not 8-segment programmer) SEG.d SEG.d SEG.d SEG.d Flash active segment type in the lower readout of the home display (no / YES) 2-12 2408 and 2404 Controller… -
Page 34
Event output: OFF/on (not 8-segment programmer) Segment synchronisation: no/YES SYnc SYnc SYnc SYnc (not 8-seg progr) End of prog − dwEl, RSEt, S OP End.t End.t End.t End.t Power level in end segment 2408 and 2404 Controller 2-13… -
Page 35
One-shot autotune enable U.br Valve sensor break strategy Adaptive tune enable drA.t drA.t drA.t drA.t Adaptive tune trigger level in display units. Range = 1 to 9999 Automatic Droop Compensation (PD control only) 2-14 2408 and 2404 Controller… -
Page 36
PV = ip.2 above ‘Hi.Ip’ Derived function, (if configured) PV = (f.1 x iP1) + (f.2 x iP2). ‘F.1’ and ‘F.2’ are scalars with the range -9.99 to 10.00 PV.ip Selects ‘ip.1’ or ‘ip.2’ Continued in next column 2408 and 2404 Controller 2-15… -
Page 37
Network connected but not PID output to motorised valve operational oFF.L Network not connected ACCS ACCS ACCS ACCS Access List codE Access password Goto Goto level — OPEr, FuLL, Edit or conF ConF Configuration password 2-16 2408 and 2404 Controller… -
Page 38
_HSP* 4rAt Load Current High alarm PV Rate of change alarm _HCr* Always assigned to Alarm 4 * In place of the dash, the first character will indicate the alarm number. Table 2-1 Process alarms 2408 and 2404 Controller 2-17… -
Page 39
Indicates that the PDS input is short circuit Circuit Mode 5 only Hw.Er Hw.Er Hw.Er Hw.Er Hardware error Check that the correct modules are fitted. Indication that a module is of the wrong type, missing, or faulty. 2-18 2408 and 2404 Controller… -
Page 40
Acknowledge by pressing ‘page’ key two hours and ‘scroll’ key together P.br P.br P.br P.br Potentiometer break Check that the feedback potentiometer is correctly connected or the pot is not open circuit Table 2-2 Diagnostic alarms 2408 and 2404 Controller 2-19… -
Page 41
Operation Installation and Operation Handbook 2-20 2408 and 2404 Controller… -
Page 42
(See Edit level at the end of this chapter). conF Configuration This special level allows access to set up the fundamental characteristics of the controller. Figure 3-1 Access levels 2408 and 2404 Controller… -
Page 43
If no button is pressed for ten seconds, you will be returned to the Home display. Alternatively, pressing together takes you immediately back to the Home display. 2408 and 2404 Controller… -
Page 44
To return to operator level from either ‘FuLL’ or ‘Edit’ level, repeat entry of the password and select ‘OPEr’ on the ‘Goto’ display. In ‘Edit’ level, the controller will automatically return to operator level if no button is pressed for 45 seconds. 2408 and 2404 Controller… -
Page 45
A maximum of twelve parameters can be promoted. Promoted parameters are automatically ‘alterable’. Please note, in the ‘PrOG List’, the parameters from segment number (SEG.n) onwards cannot be promoted. 2408 and 2404 Controller… -
Page 46
Relative cool Only present if cooling has been configured and a module is fitted. Sets the cooling proportional band, which equals the Pb gain value divided by the rEL value. Table 4-1 Tuning parameters 2408 and 2404 Controller… -
Page 47
Tuning Installation and Operation Handbook AUTOMATIC TUNING Two automatic tuning methods are provided in the 2408 and 2404: • A one-shot tuner, which automatically sets up the initial values of the parameters listed in Table 4-1 on the previous page. -
Page 48
Adaptive tune should not be used: 1. Where the process is subjected to regular external disturbances that could mislead the adaptive tuner. 2. On highly interactive multiloop applications. However, moderately interactive loops, such as multi-zone extruders, should not give a problem. 2408 and 2404 Controller… -
Page 49
5. Set the Pb, ti, td parameter values according to the calculations given in Table 4-2. Type of control Proportional Integral time ‘ti’ Derivative time band ‘Pb’ ‘td’ Proportional only P + I control 2.2xB 0.8xT P + I + D control 1.7xB 0.5xT 0.12xT Table 4-2 Tuning values 2408 and 2404 Controller… -
Page 50
In example (a) increase ‘Lcb’ by the overshoot value. In example (b) reduce ‘Lcb’ by the undershoot value. Example (a) Temperature Setpoint Overshoot Example (b) Temperature Setpoint Undershoot Time Where the temperature approaches setpoint from above, you can set ‘Hcb’ in a similar manner. 2408 and 2404 Controller… -
Page 51
The display shows tU.Er — Tune Error. This alarm could occur if: 1. The process to be tuned has a very slow response time 2. The sensor has failed or is incorrectly aligned 3. The loop is broken or not responding correctly 2408 and 2404 Controller… -
Page 52
Installation and Operation Handbook Tuning MOTORISED VALVE CONTROL The 2408 and 2404 can be configured for motorised valve control as an alternative to the standard PID control algorithm. This algorithm is designed specifically for positioning motorised valves. These are ordered pre-configured as Model numbers: •… -
Page 53
1. In Operator level, press the AUTO/MAN button to put the controller in Manual mode. 2. Drive the valve to its fully open position using 3. Press until you get to ‘ip-List’. 4. Press to get to ‘PCAL-OFF’. 2408 and 2404 Controller… -
Page 54
21. Calibration is complete when the display returns to ‘GO-no’. 22. Press together to return directly to the Operator level. 23. Press the AUTO/MAN button to place the controller in AUTO and the calibration of the position feedback potentiometer is now complete. 2408 and 2404 Controller… -
Page 55
The 2408 and 2404 has two sets of PID values. You can select the active set from either a digital input, or from a parameter in the PID list, or you can transfer automatically in gain scheduling mode. -
Page 56
Programmer Operation Chapter 5 PROGRAMMER OPERATION This chapter deals with the setpoint programming option. All 2408 / 2404 instruments have a basic 8-segment programmer built-in as standard. This facility must be enabled by the user, as explained in the section, Configuring the Programmer. -
Page 57
WHAT IS SETPOINT PROGRAMMING? Many applications need to vary temperature, or process value, with time. Such applications need a controller which varies a setpoint as a function of time; all 2408 and 2404 models can do this. The setpoint is varied by using a setpoint program. Within each 2408 and 2404 controller, there is a software module called the programmer, which stores one, or more, such programs and drives the setpoint according to the selected program. -
Page 58
(see the final topic in this chapter). When the program ends, the programmer is put into either, a continuous Dwell state with all outputs staying unchanged, or the Reset state, or to a settable power level. Table 5-1 Segment Types 2408 and 2404 Controller… -
Page 59
Holdback will also occur if the PDSIO output is open circuit. This can be disabled in configuration by selecting the PdS output as SP.nH — ‘setpoint retransmission without holdback’ The program is complete. RUN light flashes Table 5-2 Program States 2408 and 2404 Controller… -
Page 60
‘hoLd’. Such changes remain active only for the duration of the segment; the segment parameters will revert to their original (stored) values whenever the segment is re-executed. 2408 and 2404 Controller… -
Page 61
There are four different Holdback types. The choice of type is made by setting a parameter when creating a program, and may be one of the following:− ‘OFF’ − Disables Holdback − therefore no action is taken. 2408 and 2404 Controller… -
Page 62
Servo to new PV level Time Time Ramp Ramp Segment Segment Dwell Segment Figure 5-2 Continue after a power fail Figure 5-3 Ramp back after a power fail If ‘rSEt’ is selected, then when power is restored the program terminates. 2408 and 2404 Controller… -
Page 63
Four stored programs • Twenty stored programs Press Holdback Strategy to select: • Holdback type to be set in each segment • ProG Holdback type to be set for the whole program Press Continued on the next page. 2408 and 2404 Controller… -
Page 64
Event Outputs (not in 8-segment programmer) to select: • Event outputs disabled • Event outputs enabled Press Synchronisation (not in 8-segment programmer) to select: • Synchronisation disabled • Synchronisation enabled Press to return the list header. 2408 and 2404 Controller… -
Page 65
— see Chapter 6, Configuration. To invoke this mode of operation, the parameter ‘bcd’ in ‘inst-Conf’ must be set to ‘PrOg’. until you reach ‘bcd’. Press Use the buttons, to select ‘PrOG’. PrOG 5-10 2408 and 2404 Controller… -
Page 66
• Deviation High Holdback • bAnd Deviation Band Holdback Press Holdback value Note! The value set in this parameter is always for the whole program. to set the value. Press Continued on the next page. 2408 and 2404 Controller 5-11… -
Page 67
The parameters that follow ‘SEG.n’ set up the characteristics of the individually-selected segment number. By defining the characteristics of each segment of the program, you define the whole program. Press Continued on the next page. 5-12 2408 and 2404 Controller… -
Page 68
• Deviation Low Holdback • Deviation High Holdback • bAnd Deviation Band Holdback Press Target setpoint Target setpoint for ‘rmP.r’, ‘rmP.t’ or ‘StEP’ segments. Set the target setpoint using Press Continued on the next page. 2408 and 2404 Controller 5-13… -
Page 69
Number of cycles of the cALLed program Only appears for ‘cALL’ segments. (multi-program controllers only) Sets the number of cycles of the cALLed program from 1 to 999, using Press Continued on the next page. 5-14 2408 and 2404 Controller… -
Page 70
Synchronisation Disabled Note: This event output, if used, occupies the position of ‘out8’. Press End segment to select: • dwEl An indefinite dwell • rSEt Reset. • S OP End Segment Output Power Level Press 2408 and 2404 Controller 5-15… -
Page 71
Note: In programmer/controller software versions 3.56 onwards this parameter has been replaced by a parameter End.P End.P which appears at the end of the Output List, see End.P End.P Chapter 2 to return to the ProG-LiSt header. Press 5-16 2408 and 2404 Controller… -
Page 72: Chapter 6 Configuration
Incorrect configuration could result in damage to the process being controlled and/or personal injury. It is the responsibility of the person commissioning the process to ensure that the configuration is correct. 2408 and 2404 Controller…
-
Page 73
‘locked’ then pressing at this point will take you to the ‘Exit’ display with ‘no’ in the lower to return to the ‘ConF’ readout. Simply press display.) You will obtain the first display of configuration. 2408 and 2404 Controller… -
Page 74
There are TWO passwords. These are stored in the Password configuration list and can be selected and changed in the same manner as any other configuration parameter. The password names are: ‘ACC.P’ which protects access to Full level and Edit level ‘cnF.P’ which protects access to Configuration level. 2408 and 2404 Controller… -
Page 75
1200 rmP.U Ltch inp.H PSEc diSA 50.0 bLoc dtYP VaL.L SYnc nonE VaL.H diSA 100.0 PwrF Ltch Fwd.t bLoc nonE Pd.tr Sbr.t Ltch Sb.OP bLoc nonE Fig 6.1a Navigation Diagram (Part A) GSch 2408 and 2404 Controller… -
Page 76
‘mV.C’, or ‘mA.C’, or ‘V.C’. The navigation diagram shows typical parameters, but is dependant upon the exact Fig 6.1b Navigation Diagram (Part B) configuration of the instrument. The following sheets show the full list of parameters. 2408 and 2404 Controller… -
Page 77
Configuration Installation and Operation Handbook NAVIGATION DIAGRAM (PART C) Calibration Password Config Config PASS Exit ConF ConF ACC.P nonE cnF.P UCAL pt1.L pt1.H OF1.L OF1.H pt2.L pt2.H OF2.L OF2.H Fig 6.1c Navigation Diagram (Part C) 2408 and 2404 Controller… -
Page 78
Manual mode Step Steps to forced output level. Value set in ‘FOP’ of ‘op-List’ in Operator Level none BCD input function Not used prog Select program number Select setpoint number gsch Gain schedule enable Disabled Enabled 2408 and 2404 Controller… -
Page 79
If a decimal point was configured, negative display and setpoint ranges were limited to -99.9 in previous software versions. The range has been increased to -199.9 by combining the negative sign with the figure one. This allows Setpoints, Process Variables, Alarm Setpoints and Programmers to be set to -199.9. 2408 and 2404 Controller… -
Page 80
Linear Input Scaling − The next 4 parameters only appear if a linear or sq rt input is chosen. Displayed Value inp.L Input value low VAL. H inp.H Input value high VAL.L Displayed reading low VAL. L Electrical VAL.H Input Displayed reading high inP.L inP.H 2408 and 2404 Controller… -
Page 81
Local setpoint tracks programmer SP rmP.U PSEc Setpoint rate limit units Per second Pmin Per minute Per hour Remote setpoint configuration nonE Disable Remote setpoint Loc.t Remote setpoint + local trim rmt.t Remote trim + local setpoint 6-10 2408 and 2404 Controller… -
Page 82
Evnt’ means that the alarm is used to trip an external event. If this option is selected the front panel alarm message will not appear. ‘mAn’ means that the alarm will be latched, and can only be reset after it has first cleared (called ‘manual reset mode’). 2408 and 2404 Controller 6-11… -
Page 83
Reset the program Srvo to.PV Starting setpoint of a From the Process Value (PV) to.SP program (Servo point) From the setpoint Programmable event Disabled outputs Enabled SYNC Synchronisation of programs Disabled of several programmers Enabled 6-12 2408 and 2404 Controller… -
Page 84
Standby — ALL control outputs turned OFF (alarm Outputs are not affected) PV.SL PV Select: Closed = PV1 / Open = PV2 Advance to End of Segment and to Target Setpoint PrGn Program number AmPS Current – LB only 2408 and 2404 Controller 6-13… -
Page 85
YES / no Programmer event output active, where ‘n’ = event number from 1 to 8. (Not available with 8-segment programmer.) Digital Events SEnS Output Module Figure 6-2 Combining several digital events on to one output 6-14 2408 and 2404 Controller… -
Page 86
PDS PV retransmission OP.oP PDS output power retransmission Er.OP PDS error signal retransmission SP.nH PDS setpoint retransmission — no holdback Output Scaling Displayed Value VAL.L Retransmitted value low VAL.H VAL.H Retransmitted Value High Retransmitted VAL.L Output 100% 2408 and 2404 Controller 6-15… -
Page 87
Electrical Input 100% Note: Having configured the module function as remote setpoint you must then specify the type of remote setpoint in the SP-conf list Comms 2 module config As per Comms 1 module configuration 6-16 2408 and 2404 Controller… -
Page 88
= 10V A Transducer Power Supply does not provide any calibration facility and is simply a 5 or 10V power supply. To invert a PID output, the Val. H can be set below the Val.L 2408 and 2404 Controller 6-17… -
Page 89
Remote OP power max. rOP.L Remote OP power min. VPoS Motorised valve position VAL.L Displayed value low Displayed value equivalent to 0% potentiometer position VAL.H VAL.H Displayed value high equivalent to 100% potentiometer position Potentiometer VAL.L position 100% 6-18 2408 and 2404 Controller… -
Page 90
Linear Input Scaling − The next four parameters only appear if a linear input is chosen. Displayed Value inP.L Input value low VAL.H inP.H Input value high VAL.L Displayed value low VAL.L Electrical VAL.H Displayed value high Input inP.L inP.H 2408 and 2404 Controller 6-19… -
Page 91
Linearisation Value representing in 8 Note: Custom Linearisation is only available when ‘3a-Conf’or iP- ConF list has ‘inpt’ set to ‘mV.C’, or ‘mA.C’, or ‘V.C’. 2. The values and inputs must be continuously increasing or decreasing 6-20 2408 and 2404 Controller… -
Page 92
Note. When a DC input module is installed for the first time, or there is a requirement to change one, then the microprocessor in the controller needs to read the factory calibration data stored in the module. Select ‘FACt’ as the calibration value. Step to ‘GO’ and start calibration. 2408 and 2404 Controller 6-21… -
Page 93
PASS PASS PASS Password configuration ACC.P FuLL or Edit level password cnF.P Configuration level password Note:- When passwords are changed please make a note of the new numbers Exit Exit Exit Exit no/YES Exit configuration 6-22 2408 and 2404 Controller… -
Page 94: Configuration Examples
= 5Vdc Press (twice) to SEnS read ‘Sens’ The Transducer Power supply uses existing software Press written for digital modules. A select ‘inv’ or ‘nor’ list of parameters follow which are not applicable to this module. 2408 and 2404 Controller 6-23…
-
Page 95
FuLL — the decimal point Press to read position is implied, eg 100.1 ‘rES’ is transmitted as 1001. Press FuLL ‘int’ — rounded to the select ‘FuLL’ or ‘int’ nearest integer value 6-24 2408 and 2404 Controller… -
Page 96
Addr ‘Addr’ 10. Press select the address Indicates the network status:- 11. Press to read ‘nw.St’ ‘run’ = network connected nw.St and operational ‘rdy’ = network connected but not operational ‘OFF.L’ = network not connected 2408 and 2404 Controller 6-25… -
Page 97
Configuration Installation and Operation Handbook 6-26 2408 and 2404 Controller… -
Page 98
Calibrate the controller to suit the characteristics of a particular installation. Remove long term drift in the factory set calibration. User calibration works by introducing a single point, or two-point, offset onto the factory set calibration. 2408 and 2404 Controller… -
Page 99
Press until you reach ‘UCAL’. User Calibration Enable UCAL to select: • YES: Calibration enable • Calibration disabled together to go to the Exit display. Press Exit configuration to select ‘YES’ to return to Operator level. 2408 and 2404 Controller… -
Page 100
‘CAL’ display. Calibration type • FACt: Factory Calibration • USEr: User Calibration FACt to select ‘FACt’. Selecting ‘FACt’ reinstates the factory calibration and allows the application of a single fixed offset. Press continued on the next page 2408 and 2404 Controller… -
Page 101
‘iP-LiSt’ header. To protect the calibration against unauthorised adjustment, return to Operator level and make sure that the calibration parameters are hidden. Parameters are hidden using the ‘Edit’ facility described in Chapter 3, Access Levels. 2408 and 2404 Controller… -
Page 102
‘CAL’ display. Calibration type • FACt: Factory Calibration • USEr: User Calibration to select ‘USEr’. FACt Selecting ‘USEr’ enables two-point calibration. [If two-point calibration is unsatisfactory, select ‘FACt’ to return to the factory set calibration.] Press 2408 and 2404 Controller… -
Page 103
‘ip-List’ header. To perform the High-point Calibration, repeat the above procedure, selecting ‘ip1.H’ in the ‘CAL.S’ display for adjustment. Press three times. Calibration type ‘USEr’ was selected for the Low-point Calibration, and has remained selected. USEr Press 2408 and 2404 Controller… -
Page 104
‘Edit’ facility described in Chapter 3. To perform a User Calibration on Input 2, proceed as with Input 1 above, except that when ‘CAL.S-nonE’ appears, press until ‘CAL.S-iP2.L’ is obtained, then proceed as with Input 1. Repeat the procedure for ‘iP2.H’. 2408 and 2404 Controller… -
Page 105
Offset Low for Input 2 Calculated offset, in display units. OF2.H Offset High for Input 2 Calculated offset, in display units. Note: The value of each of the parameters in the above table may also be altered by using buttons. 2408 and 2404 Controller… -
Page 106
Appendix A UNDERSTANDING THE ORDERING CODE The 2408 and 2404 controllers have a modular hardware construction, which accepts up to three plug-in Input/Output modules and two communications modules to satisfy a wide range of control requirements. Two digital inputs and an optional alarm relay form part of the fixed hardware build. -
Page 107
Valve raise and lower Logic + relay Fitted unconfigured PID heat + PID cool Mode 2 + cool Logic + triac Fitted unconfigured PID heat + PID cool Mode 2 + cool Transducer P5 5Vdc 10Vdc 2408 and 2404 Controller… -
Page 108
Table A alarm options plus: German Transducer PSU Dutch Rate of change 5Vdc Spanish PDS alarms 10Vdc Heater break detect Swedish Current monitor heater brk Italian Current monitor SSR fail Program event 7 (note 7) Program END output 2408 and 2404 Controller… -
Page 109
32 to 3650 (Hoskins) W5%Re/W26%Re 10 to 2300 50 to 4172 (Englehard) W5%Re/W26%Re 0 to 2000 32 to 3632 (Bucose) Pt10%Rh/Pt40%Rh 200 to 1800 392 to 3272 Exergen K80 I.R. -45 to 650 -50 to 1200 pyrometer 2408 and 2404 Controller… -
Page 110
CTX (mode 5) (input 2 only) The example given in the coding is for 2408 PID controller, 85 to 264 Vac, logic heating, relay cooling, low alarm relay, high alarm relay, RS485 Modbus comms, PDSIO setpoint retransmission, type K thermocouple, 0 to 1000 C, Auto/manual select, second setpoint select, manual button disabled. -
Page 111
Sensor input table. For these inputs, the values entered here are the low and high setpoint limits. For process inputs, the values are the display scaling. corresponding to the minimum and maximum input values. 2408 and 2404 Controller… -
Page 112
EN 50081-2 and EN 50082-2. For more information on product compliance refer to the Technical Construction File. SERVICE AND REPAIR This controller has no user serviceable parts. Contact your nearest Eurotherm Controls agent for repair. Caution: Charged capacitors Before removing an instrument from its sleeve, disconnect the supply and wait at least two minutes to allow capacitors to discharge. -
Page 113
Due to RFI Filtering there is an earth leakage current of less than 0.5mA. This may affect the design of an installation of multiple controllers protected by Residual Current Device, (RCD) or Ground Fault Detector, (GFD) type circuit breakers. 2408 and 2404 Controller… -
Page 114
• the controller setpoint set too high. Where damage or injury is possible, we recommend fitting a separate over-temperature protection unit, with an independent temperature sensor, which will isolate the heating circuit. 2408 and 2404 Controller… -
Page 115
To ensure compliance with the European EMC directive certain installation precautions are necessary as follows: • For general guidance refer to Eurotherm Controls EMC Installation Guide, HA025464. • When using relay or triac outputs it may be necessary to fit a filter suitable for suppressing the emissions. -
Page 116
12Vdc, 8mA per channel (isolated) Digital o/p functions As per the ordering code High current output 10Amp, 264Vac resistive. This option is not available on controller from Jan-04 Triac rating 1A, 30 to 264Vac resistive (isolated) Analogue outputs 2408 and 2404 Controller… -
Page 117
RS232,2-wire,RS 485 and 4 wire RS485 modules Baud rate 1200, 2400, 4800, 9600 and 19,200 baud Slave input (isolated) Remote setpoint input with holdback to master Master output Isolated from main PV. Retransmission of setpoint, process value or output 2408 and 2404 Controller… -
Page 118
C and 5 to 90% RH non-condensing Storage temperature -10 to +70 Panel sealing IP65 Dimensions 2408: 48mm wide x 96mm high x 150mm deep 2404: 96mm wide x 96mm high x 150mm deep Weight 250g EMC standards EN61326-1 generic standards for industrial environments… -
Page 119
Technical Specification Installation and Operation Handbook 2408 and 2404 Controller… -
Page 120
DIAGNOSTICS Current flowing in a system of electrical heating elements (the ‘Load’) can be displayed on the controller by using a Eurotherm TE10 SSR fitted with intelligent current transformer, PDCTX, or an SSR or contactor with an external PDCTX. Load current monitoring and diagnostics may be used with any time proportioned output,… -
Page 121
2. Eurotherm intelligent current transformer type PD/CTX + contactor or zero voltage switching SSR 2408 or 2404 controller configured for PDS mode 2 option using logic output. This module must be fitted in module position 1. (order code M2). Controller… -
Page 122
1. Eurotherm intelligent current transformer type PD/CTX + contactor 2. 2408 or 2404 controller configured for PDS mode 5 option using logic, relay or triac output. This module must be fitted in module position 1. Digital input LB (order code M5) must be configured to accept PDCTX input as described in the configuration section of this appendix. -
Page 123
Meter mode applies to mode 5 only. If low current alarms are not configured the current displayed is a filtered instantaneous RMS value. This behaves like a damped analogue meter. It may be used in applications where the current sensor is not linked to control, for example, telemetry, indication. 2408 and 2404 Controller… -
Page 124
Ct.OP Current Indicates that the PDS input is open circuit. Transformer Mode 5 only Open Circuit Ct.Sh Current Indicates that the PDS input is short circuit Transformer Mode 5 only Short Circuit 2408 and 2404 Controller… -
Page 125
, such as control. Any one or more alarms can be attached to an output, which will operate when an alarm occurs. Contacts are rated at 2A 264Vac for operating external beacons or audible devices. 2408 and 2404 Controller… -
Page 126
SSr1 or is set to PDS mode SSr 2 as required. This is the lower PID Press to show VAL.L demand level VAL.L To set the minimum PID signal to 0% Press to show 0.0 2408 and 2404 Controller… -
Page 127
This is the maximum 100.0 output power Press To set the max output power to 100 to show 100.0 SenS Press to show This sets the output SEnS signal to normal for heating control Press to show nor 2408 and 2404 Controller… -
Page 128
Press to select AmPs The system is designed to operate in either mode 2 or mode 5 configuration only. Selecting both simultaneously will disable the output. However, mode 1 and mode 5 can be used together. 2408 and 2404 Controller… -
Page 129
To make alarm 2 = has been accepted High Current Press to show HCr Note:- The above alarms are known as SOFT ALARMS because they are indication only. D-10 2408 and 2404 Controller… -
Page 130
YES or output will not activate Repeat the above step for every alarm to be attached to the output Alarms Connected to a Relay Output Soft SEnS Alarms Output Module 2408 and 2404 Controller D-11… -
Page 131
Scalar = 100/N Where N = Turns through PDCTX Scalar Scalar Maximum Resolvable Current TE10 Determined by the maximum range of the SSR PDCTX 100A (or 100 ampere turns) Finally Exit configuration level. See Chapter 5. D-12 2408 and 2404 Controller… -
Page 132
Appendix E: Profibus Communications Introduction The 2408f and 2404f are special versions of the 2408 and 2404 controllers designed for Profibus-DP communications. The ‘standard’ 2408 or 2404 controllers cannot be upgraded to a 2408f or 2404f as the latter uses a different version of the microprocessor board. -
Page 133: Technical Specification
2408f or 2404f controller Twisted pair Intermediate stations Last Station Not connected Shield VP (+5Vdc Voltage Potential) 390Ω B (Rx/Tx +ve) 220Ω A (Rx/Tx -ve) Last station only requires 390Ω DGND (Digital ground) terminating resistors 2408f or 2404f controller 2408 and 2404 Controller…
-
Page 134
400m 200m Type B cable 1200m 1200m 1200m 600m 200m Belden B3079A meets cable A specifications, but there are other choices. For more information refer to the ‘Profibus Product Guide’ produced by the Profibus User Group. 2408 and 2404 Controller… -
Page 135
From the HOME display, press LiSt Node address Addr Press to display the node address. Press to set the desired address. 0 -126 Comms Status Stat This is a read-only diagnostic display Ready to run Comms running 2408 and 2404 Controller… -
Page 136
How many parameters can I select? How many parameters can I select? Up to 117 per node, total of inputs and outputs. What can I run it on? What can I run it on? Windows 3.1, Windows 95, or Windows NT. 2408 and 2404 Controller… -
Page 137
Ensure that the last device (not necessarily a 2404/8) in the network segment is correctly terminated (see wiring diagram). • Ensure that no devices other than those at the end of a segment have termination networks fitted. • Verify operation with a duplicate device if possible. 2408 and 2404 Controller… -
Page 138
Eurotherm Limited pursues a policy of continuous development and product improvement. The specifications in this docu- ment may therefore be changed without notice. The information in this document is given in good faith, but is intended for guidance only. Eurotherm Limited will accept no responsibility for any losses arising from errors in this document. HA025132…
-
Contents
-
Table of Contents
-
Troubleshooting
-
Bookmarks
Quick Links
CONTROL SETPOINT
PROGRAMMER
ENG
Installation and operation
handbook
Related Manuals for Eurotherm Invensys 2408
Summary of Contents for Eurotherm Invensys 2408
-
Page 1
CONTROL SETPOINT PROGRAMMER Installation and operation handbook… -
Page 2
“This product is covered by one or more of the following US Patents: 5,484,206; Additional patents pending. PDS and INSTANT ACCURACY are trademarks of Eurotherm.” Issue 10 of this handbook applies to software version 4. Issue 10.0 Nov-04 Applies to 2408 and 2404 controller software version 4.0… -
Page 3
DeviceNet Communications Handbook part no. HA027506 which includes the parameter address map. • Profibus Communications Handbook part no. HA026290 • EMC (Electromagnetic Compatibility) Installation Guide, part no. HA025464 These are available on www. eurotherm.co.uk. Issue 10.0 Nov-04 Applies to 2408 and 2404 controller software version 4.0… -
Page 4: Chapter 1 Installation
Chapter 1 INSTALLATION Terminal covers Sleeve Ratchets Display screen Label Panel retaining clips Latching ears Panel sealing gasket Figure 1-1 2408 1/8 DIN controller Sleeve Terminal covers Ratchets Display screen Label Panel retaining clips Latching ears Panel sealing gasket Figure 1-2 2404 1/4 DIN controller…
-
Page 5
OP 1 OP2 cut-out 92 x 45mm 96mm 3.78in +0.8 +0.6 3.62×1.77in +0.03 +0.02 AUTO HOLD Figure 1-3 Outline dimensions of Model 2408 controller 10mm 38mm (0.4in) (1.5in) Recommended minimum spacing (Not to of controllers scale Outline dimensions Model 2404 150mm 96mm 5.91in… -
Page 6: Mechanical Installation
Installation INTRODUCTION Models 2408 and 2404 are high stability, temperature or process controllers with self and adaptive tuning. They have a modular hardware construction which accepts up to three plug- in Input/Output modules and two interface modules to satisfy a wide range of control requirements.
-
Page 7
Installation and Operation Handbook NEW SLEEVE DESIGN MKIII From Jan-03 an improved design of 1/8 DIN long sleeve is shipped with all new 2408 controllers and indicators. (The month and year of manufacture are shown in the last two pairs of digits of the instrument serial number). -
Page 8: Electrical Installation
− − Figure 1-5 Rear terminal layout − Model 2408 * The ground connection is provided as a return for internal EMC filters. It is not required for safety purposes, but must be connected in order to satisfy EMC requirements.
-
Page 9
20 − 29Vac/dc Low voltage supply Model 2404 rear terminal layout Ground Line 85 to 264Vac Neutral Ground* Input 1 Input 2 Common Alarm relay RTD/Pt100 − − Figure 1-6 Rear terminal layout − Model 2404 2408 and 2404 Controller… -
Page 10
PDS 1 mode uses a logic output module to control aTE10S solid state relay and provides a load failure alarm. PDS 2 mode uses a logic output module to control a TE10S solid state relay, provide load/SSR failure alarms, and read back the load current for display on the controller. 2408 and 2404 Controller… -
Page 11
(BUT NOT THE TRIAC) by breaking the PCB track that runs crosswise, adjacent to the edge connectors of the module. This can be done by inserting the blade of a small screwdriver into one of the two slots that bound it, and twisting. 2408 and 2404 Controller… -
Page 12
Triple logic input and output modules — see ratings on the next page Triple contact input Input 1 Input 2 Input 3 Common Triple logic input Input 1 Input 2 Input 3 Common Triple logic output Output 1 Output 2 Output 3 Common Program events 2408 and 2404 Controller… -
Page 13
>28KΩ input resistance OFF state voltage >14Vdc ON state <100Ω resistance ON state voltage <1.0Vdc Triple logic output (current sourcing) OFF state output 0 to 0.7Vdc. ON state output 12 to 13Vdc, at up to 8mA. 1-10 2408 and 2404 Controller… -
Page 14
Installation COMMUNICATION MODULES 1 AND 2 All 2408 and 2404 controllers can be fitted with up to two plug-in communications modules. Only one of the two modules can be for serial communications and this will normally be installed in position COMMS 1 (although it is possible to install the serial communications module in position COMMS 2. -
Page 15
All resistors are 220 ohm 1/4W carbon composition. Local grounds are at equipotential. Where equipotential is not available wire into separate zones using a galvanic isolator. Use a repeater (KD845) for more than 32 units. Figure 1-9 EIA-485 wiring 1-12 2408 and 2404 Controller… -
Page 16
• 2 fuses or circuit breakers to protect the bus from excessive current which could damage the cable and connectors. • The earth connection, HF, to be connected to the main supply earth terminal. 2408 and 2404 Controller 1-13… -
Page 17
2400 Controller Network Supply 24Vdc ( +1%) 250mV p-p Ripple (SLAVE) Address N+1 * Fit 121! resistor to last instrument in the chain Daisy chain to further instruments To configure DeviceNet Communications see Chapter 6. 1-14 2408 and 2404 Controller… -
Page 18
Controllers supplied with model numbers 2408f and 2404f are fitted with ProfiBus communications modules fitted in the H slot. Further details of ProfiBus communications is given in Appendix E and the ProfiBus Communications handbook part number HA026290. This handbook can be downloaded from www.eurotherm.co.uk. Station 1 Not connected… -
Page 19: Typical Wiring Diagram
1A(T) Logic heating output Triac cooling output Heating power fuse (load dependent) − Solid State Relay * Heater Cooling Solenoid Fig 1-10 Typical wiring diagram, Model 2408 Controller For logic drive capability see following chart:- 1-16 2408 and 2404 Controller…
-
Page 20
TC1027 TE200S TC2000 RS3D Standard Multi- Logic V Logic Logic Logic drive Logic 2S 3P 1S2P 6S 1P 3S 3P 3S 3P 3S 1P 4S 2P Triple 4S 1P 2S 1P 2S 1P logic 2408 and 2404 Controller 1-17… -
Page 21
+ + + + RTD/Pt100 + + + + Input + + + + Motor Module Feedback Potentiometer − − − − − − − − − − − − (Optional) Fig 1-11 Motorised valve connections 1-18 2408 and 2404 Controller… -
Page 22
This chapter has nine topics: • FRONT PANEL LAYOUTS • BASIC OPERATION • OPERATING MODES • AUTOMATIC MODE • MANUAL MODE • PARAMETERS AND HOW TO ACCESS THEM • NAVIGATION DIAGRAM • PARAMETER TABLES • ALARMS 2408 and 2404 Controller… -
Page 23
Run/Hold HOLD Manual mode Program in Hold Page Scroll Down Button Button Button Button Figure 2-1 Model 2408 front panel layout 2404 2404 Output 2 Output 1 OP 1 OP 2 OP 1 Upper readout Lower readout Remote setpoint/ Setpoint 2… -
Page 24
Press to select a new parameter in a list. Down button Press to decrease a value in the lower readout. Up button Press to increase a value in lower readout. Figure 2-3 Controller buttons and indicators 2408 and 2404 Controller… -
Page 25: Basic Operation
If the controller detects an alarm condition, it flashes an alarm message in the Home display. For a list of all the alarm messages, their meaning and what to do about them, see Alarms at the end of this chapter. 2408 and 2404 Controller…
-
Page 26: Operating Modes
Two other modes are also available: • Remote Setpoint mode, in which the setpoint is generated from an external source. In this mode, the REM light will be on. • Programmer mode which is explained in Chapter 5, Programmer Operation. 2408 and 2404 Controller…
-
Page 27: Automatic Mode
Output Power display may access further parameters. These may be in this scroll list if the ‘Promote’ feature has been used (see Chapter 3, Edit Level). When you reach the end of this scroll list, pressing will return you to the Home display. 2408 and 2404 Controller…
-
Page 28: Manual Mode
Output Power display may access further parameters. These may be in this scroll list if the ‘Promote’ feature has been used (see Chapter 3, Edit Level). When you reach the end of this scroll list, pressing will return you to the Home display. 2408 and 2404 Controller…
-
Page 29
When you reach the end of the list, you will return to the list header. From within a list you can return to the current list header at any time can by pressing To step to the next list header, press once again. 2408 and 2404 Controller… -
Page 30
. During adjustment, single presses change the value by one digit. Keeping the button pressed speeds up the rate of change. Two seconds after releasing either button, the display blinks to show that the controller has accepted the new value. 2408 and 2404 Controller… -
Page 31
Auto PrG.t 35.0 rEL.C Lb t rEL.2 1.00 1.00 FASt rAtE diAG FF.Pb out.n SEG.n FF.tr ti.2 SEG.n SYnc tYPE FF.dv td.2 tYPE 100.0 50.0 dwEl SEG.d tYPE dwEl Figure 2-7a Navigation diagram (Part A) 2-10 2408 and 2404 Controller… -
Page 32
The shaded boxes are normally hidden in Operator level. To see all the available parameters you must select Full level. SP H See Chapter 3, Access Levels. 100.0 Figure 2-7b Navigation diagram (Part B) For additional parameters — see tables 2408 and 2404 Controller 2-11… -
Page 33
Event output states (OFF / on) (not 8-segment programmer) SYnc SYnc SYnc SYnc Segment synchronisation (no / YES) (not 8-segment programmer) SEG.d SEG.d SEG.d SEG.d Flash active segment type in the lower readout of the home display (no / YES) 2-12 2408 and 2404 Controller… -
Page 34
Event output: OFF/on (not 8-segment programmer) Segment synchronisation: no/YES SYnc SYnc SYnc SYnc (not 8-seg progr) End of prog − dwEl, RSEt, S OP End.t End.t End.t End.t Power level in end segment 2408 and 2404 Controller 2-13… -
Page 35
One-shot autotune enable U.br Valve sensor break strategy Adaptive tune enable drA.t drA.t drA.t drA.t Adaptive tune trigger level in display units. Range = 1 to 9999 Automatic Droop Compensation (PD control only) 2-14 2408 and 2404 Controller… -
Page 36
PV = ip.2 above ‘Hi.Ip’ Derived function, (if configured) PV = (f.1 x iP1) + (f.2 x iP2). ‘F.1’ and ‘F.2’ are scalars with the range -9.99 to 10.00 PV.ip Selects ‘ip.1’ or ‘ip.2’ Continued in next column 2408 and 2404 Controller 2-15… -
Page 37
Network connected but not PID output to motorised valve operational oFF.L Network not connected ACCS ACCS ACCS ACCS Access List codE Access password Goto Goto level — OPEr, FuLL, Edit or conF ConF Configuration password 2-16 2408 and 2404 Controller… -
Page 38
_HSP* 4rAt Load Current High alarm PV Rate of change alarm _HCr* Always assigned to Alarm 4 * In place of the dash, the first character will indicate the alarm number. Table 2-1 Process alarms 2408 and 2404 Controller 2-17… -
Page 39
Indicates that the PDS input is short circuit Circuit Mode 5 only Hw.Er Hw.Er Hw.Er Hw.Er Hardware error Check that the correct modules are fitted. Indication that a module is of the wrong type, missing, or faulty. 2-18 2408 and 2404 Controller… -
Page 40
Acknowledge by pressing ‘page’ key two hours and ‘scroll’ key together P.br P.br P.br P.br Potentiometer break Check that the feedback potentiometer is correctly connected or the pot is not open circuit Table 2-2 Diagnostic alarms 2408 and 2404 Controller 2-19… -
Page 41
Operation Installation and Operation Handbook 2-20 2408 and 2404 Controller… -
Page 42
(See Edit level at the end of this chapter). conF Configuration This special level allows access to set up the fundamental characteristics of the controller. Figure 3-1 Access levels 2408 and 2404 Controller… -
Page 43
If no button is pressed for ten seconds, you will be returned to the Home display. Alternatively, pressing together takes you immediately back to the Home display. 2408 and 2404 Controller… -
Page 44
To return to operator level from either ‘FuLL’ or ‘Edit’ level, repeat entry of the password and select ‘OPEr’ on the ‘Goto’ display. In ‘Edit’ level, the controller will automatically return to operator level if no button is pressed for 45 seconds. 2408 and 2404 Controller… -
Page 45
A maximum of twelve parameters can be promoted. Promoted parameters are automatically ‘alterable’. Please note, in the ‘PrOG List’, the parameters from segment number (SEG.n) onwards cannot be promoted. 2408 and 2404 Controller… -
Page 46
Relative cool Only present if cooling has been configured and a module is fitted. Sets the cooling proportional band, which equals the Pb gain value divided by the rEL value. Table 4-1 Tuning parameters 2408 and 2404 Controller… -
Page 47
Tuning Installation and Operation Handbook AUTOMATIC TUNING Two automatic tuning methods are provided in the 2408 and 2404: • A one-shot tuner, which automatically sets up the initial values of the parameters listed in Table 4-1 on the previous page. -
Page 48
Adaptive tune should not be used: 1. Where the process is subjected to regular external disturbances that could mislead the adaptive tuner. 2. On highly interactive multiloop applications. However, moderately interactive loops, such as multi-zone extruders, should not give a problem. 2408 and 2404 Controller… -
Page 49
5. Set the Pb, ti, td parameter values according to the calculations given in Table 4-2. Type of control Proportional Integral time ‘ti’ Derivative time band ‘Pb’ ‘td’ Proportional only P + I control 2.2xB 0.8xT P + I + D control 1.7xB 0.5xT 0.12xT Table 4-2 Tuning values 2408 and 2404 Controller… -
Page 50
In example (a) increase ‘Lcb’ by the overshoot value. In example (b) reduce ‘Lcb’ by the undershoot value. Example (a) Temperature Setpoint Overshoot Example (b) Temperature Setpoint Undershoot Time Where the temperature approaches setpoint from above, you can set ‘Hcb’ in a similar manner. 2408 and 2404 Controller… -
Page 51
The display shows tU.Er — Tune Error. This alarm could occur if: 1. The process to be tuned has a very slow response time 2. The sensor has failed or is incorrectly aligned 3. The loop is broken or not responding correctly 2408 and 2404 Controller… -
Page 52
Installation and Operation Handbook Tuning MOTORISED VALVE CONTROL The 2408 and 2404 can be configured for motorised valve control as an alternative to the standard PID control algorithm. This algorithm is designed specifically for positioning motorised valves. These are ordered pre-configured as Model numbers: •… -
Page 53
1. In Operator level, press the AUTO/MAN button to put the controller in Manual mode. 2. Drive the valve to its fully open position using 3. Press until you get to ‘ip-List’. 4. Press to get to ‘PCAL-OFF’. 2408 and 2404 Controller… -
Page 54
21. Calibration is complete when the display returns to ‘GO-no’. 22. Press together to return directly to the Operator level. 23. Press the AUTO/MAN button to place the controller in AUTO and the calibration of the position feedback potentiometer is now complete. 2408 and 2404 Controller… -
Page 55
The 2408 and 2404 has two sets of PID values. You can select the active set from either a digital input, or from a parameter in the PID list, or you can transfer automatically in gain scheduling mode. -
Page 56
Programmer Operation Chapter 5 PROGRAMMER OPERATION This chapter deals with the setpoint programming option. All 2408 / 2404 instruments have a basic 8-segment programmer built-in as standard. This facility must be enabled by the user, as explained in the section, Configuring the Programmer. -
Page 57
WHAT IS SETPOINT PROGRAMMING? Many applications need to vary temperature, or process value, with time. Such applications need a controller which varies a setpoint as a function of time; all 2408 and 2404 models can do this. The setpoint is varied by using a setpoint program. Within each 2408 and 2404 controller, there is a software module called the programmer, which stores one, or more, such programs and drives the setpoint according to the selected program. -
Page 58
(see the final topic in this chapter). When the program ends, the programmer is put into either, a continuous Dwell state with all outputs staying unchanged, or the Reset state, or to a settable power level. Table 5-1 Segment Types 2408 and 2404 Controller… -
Page 59
Holdback will also occur if the PDSIO output is open circuit. This can be disabled in configuration by selecting the PdS output as SP.nH — ‘setpoint retransmission without holdback’ The program is complete. RUN light flashes Table 5-2 Program States 2408 and 2404 Controller… -
Page 60
‘hoLd’. Such changes remain active only for the duration of the segment; the segment parameters will revert to their original (stored) values whenever the segment is re-executed. 2408 and 2404 Controller… -
Page 61
There are four different Holdback types. The choice of type is made by setting a parameter when creating a program, and may be one of the following:− ‘OFF’ − Disables Holdback − therefore no action is taken. 2408 and 2404 Controller… -
Page 62
Servo to new PV level Time Time Ramp Ramp Segment Segment Dwell Segment Figure 5-2 Continue after a power fail Figure 5-3 Ramp back after a power fail If ‘rSEt’ is selected, then when power is restored the program terminates. 2408 and 2404 Controller… -
Page 63
Four stored programs • Twenty stored programs Press Holdback Strategy to select: • Holdback type to be set in each segment • ProG Holdback type to be set for the whole program Press Continued on the next page. 2408 and 2404 Controller… -
Page 64
Event Outputs (not in 8-segment programmer) to select: • Event outputs disabled • Event outputs enabled Press Synchronisation (not in 8-segment programmer) to select: • Synchronisation disabled • Synchronisation enabled Press to return the list header. 2408 and 2404 Controller… -
Page 65
— see Chapter 6, Configuration. To invoke this mode of operation, the parameter ‘bcd’ in ‘inst-Conf’ must be set to ‘PrOg’. until you reach ‘bcd’. Press Use the buttons, to select ‘PrOG’. PrOG 5-10 2408 and 2404 Controller… -
Page 66
• Deviation High Holdback • bAnd Deviation Band Holdback Press Holdback value Note! The value set in this parameter is always for the whole program. to set the value. Press Continued on the next page. 2408 and 2404 Controller 5-11… -
Page 67
The parameters that follow ‘SEG.n’ set up the characteristics of the individually-selected segment number. By defining the characteristics of each segment of the program, you define the whole program. Press Continued on the next page. 5-12 2408 and 2404 Controller… -
Page 68
• Deviation Low Holdback • Deviation High Holdback • bAnd Deviation Band Holdback Press Target setpoint Target setpoint for ‘rmP.r’, ‘rmP.t’ or ‘StEP’ segments. Set the target setpoint using Press Continued on the next page. 2408 and 2404 Controller 5-13… -
Page 69
Number of cycles of the cALLed program Only appears for ‘cALL’ segments. (multi-program controllers only) Sets the number of cycles of the cALLed program from 1 to 999, using Press Continued on the next page. 5-14 2408 and 2404 Controller… -
Page 70
Synchronisation Disabled Note: This event output, if used, occupies the position of ‘out8’. Press End segment to select: • dwEl An indefinite dwell • rSEt Reset. • S OP End Segment Output Power Level Press 2408 and 2404 Controller 5-15… -
Page 71
Note: In programmer/controller software versions 3.56 onwards this parameter has been replaced by a parameter End.P End.P which appears at the end of the Output List, see End.P End.P Chapter 2 to return to the ProG-LiSt header. Press 5-16 2408 and 2404 Controller… -
Page 72: Chapter 6 Configuration
Incorrect configuration could result in damage to the process being controlled and/or personal injury. It is the responsibility of the person commissioning the process to ensure that the configuration is correct. 2408 and 2404 Controller…
-
Page 73
‘locked’ then pressing at this point will take you to the ‘Exit’ display with ‘no’ in the lower to return to the ‘ConF’ readout. Simply press display.) You will obtain the first display of configuration. 2408 and 2404 Controller… -
Page 74
There are TWO passwords. These are stored in the Password configuration list and can be selected and changed in the same manner as any other configuration parameter. The password names are: ‘ACC.P’ which protects access to Full level and Edit level ‘cnF.P’ which protects access to Configuration level. 2408 and 2404 Controller… -
Page 75
1200 rmP.U Ltch inp.H PSEc diSA 50.0 bLoc dtYP VaL.L SYnc nonE VaL.H diSA 100.0 PwrF Ltch Fwd.t bLoc nonE Pd.tr Sbr.t Ltch Sb.OP bLoc nonE Fig 6.1a Navigation Diagram (Part A) GSch 2408 and 2404 Controller… -
Page 76
‘mV.C’, or ‘mA.C’, or ‘V.C’. The navigation diagram shows typical parameters, but is dependant upon the exact Fig 6.1b Navigation Diagram (Part B) configuration of the instrument. The following sheets show the full list of parameters. 2408 and 2404 Controller… -
Page 77
Configuration Installation and Operation Handbook NAVIGATION DIAGRAM (PART C) Calibration Password Config Config PASS Exit ConF ConF ACC.P nonE cnF.P UCAL pt1.L pt1.H OF1.L OF1.H pt2.L pt2.H OF2.L OF2.H Fig 6.1c Navigation Diagram (Part C) 2408 and 2404 Controller… -
Page 78
Manual mode Step Steps to forced output level. Value set in ‘FOP’ of ‘op-List’ in Operator Level none BCD input function Not used prog Select program number Select setpoint number gsch Gain schedule enable Disabled Enabled 2408 and 2404 Controller… -
Page 79
If a decimal point was configured, negative display and setpoint ranges were limited to -99.9 in previous software versions. The range has been increased to -199.9 by combining the negative sign with the figure one. This allows Setpoints, Process Variables, Alarm Setpoints and Programmers to be set to -199.9. 2408 and 2404 Controller… -
Page 80
Linear Input Scaling − The next 4 parameters only appear if a linear or sq rt input is chosen. Displayed Value inp.L Input value low VAL. H inp.H Input value high VAL.L Displayed reading low VAL. L Electrical VAL.H Input Displayed reading high inP.L inP.H 2408 and 2404 Controller… -
Page 81
Local setpoint tracks programmer SP rmP.U PSEc Setpoint rate limit units Per second Pmin Per minute Per hour Remote setpoint configuration nonE Disable Remote setpoint Loc.t Remote setpoint + local trim rmt.t Remote trim + local setpoint 6-10 2408 and 2404 Controller… -
Page 82
Evnt’ means that the alarm is used to trip an external event. If this option is selected the front panel alarm message will not appear. ‘mAn’ means that the alarm will be latched, and can only be reset after it has first cleared (called ‘manual reset mode’). 2408 and 2404 Controller 6-11… -
Page 83
Reset the program Srvo to.PV Starting setpoint of a From the Process Value (PV) to.SP program (Servo point) From the setpoint Programmable event Disabled outputs Enabled SYNC Synchronisation of programs Disabled of several programmers Enabled 6-12 2408 and 2404 Controller… -
Page 84
Standby — ALL control outputs turned OFF (alarm Outputs are not affected) PV.SL PV Select: Closed = PV1 / Open = PV2 Advance to End of Segment and to Target Setpoint PrGn Program number AmPS Current – LB only 2408 and 2404 Controller 6-13… -
Page 85
YES / no Programmer event output active, where ‘n’ = event number from 1 to 8. (Not available with 8-segment programmer.) Digital Events SEnS Output Module Figure 6-2 Combining several digital events on to one output 6-14 2408 and 2404 Controller… -
Page 86
PDS PV retransmission OP.oP PDS output power retransmission Er.OP PDS error signal retransmission SP.nH PDS setpoint retransmission — no holdback Output Scaling Displayed Value VAL.L Retransmitted value low VAL.H VAL.H Retransmitted Value High Retransmitted VAL.L Output 100% 2408 and 2404 Controller 6-15… -
Page 87
Electrical Input 100% Note: Having configured the module function as remote setpoint you must then specify the type of remote setpoint in the SP-conf list Comms 2 module config As per Comms 1 module configuration 6-16 2408 and 2404 Controller… -
Page 88
= 10V A Transducer Power Supply does not provide any calibration facility and is simply a 5 or 10V power supply. To invert a PID output, the Val. H can be set below the Val.L 2408 and 2404 Controller 6-17… -
Page 89
Remote OP power max. rOP.L Remote OP power min. VPoS Motorised valve position VAL.L Displayed value low Displayed value equivalent to 0% potentiometer position VAL.H VAL.H Displayed value high equivalent to 100% potentiometer position Potentiometer VAL.L position 100% 6-18 2408 and 2404 Controller… -
Page 90
Linear Input Scaling − The next four parameters only appear if a linear input is chosen. Displayed Value inP.L Input value low VAL.H inP.H Input value high VAL.L Displayed value low VAL.L Electrical VAL.H Displayed value high Input inP.L inP.H 2408 and 2404 Controller 6-19… -
Page 91
Linearisation Value representing in 8 Note: Custom Linearisation is only available when ‘3a-Conf’or iP- ConF list has ‘inpt’ set to ‘mV.C’, or ‘mA.C’, or ‘V.C’. 2. The values and inputs must be continuously increasing or decreasing 6-20 2408 and 2404 Controller… -
Page 92
Note. When a DC input module is installed for the first time, or there is a requirement to change one, then the microprocessor in the controller needs to read the factory calibration data stored in the module. Select ‘FACt’ as the calibration value. Step to ‘GO’ and start calibration. 2408 and 2404 Controller 6-21… -
Page 93
PASS PASS PASS Password configuration ACC.P FuLL or Edit level password cnF.P Configuration level password Note:- When passwords are changed please make a note of the new numbers Exit Exit Exit Exit no/YES Exit configuration 6-22 2408 and 2404 Controller… -
Page 94: Configuration Examples
= 5Vdc Press (twice) to SEnS read ‘Sens’ The Transducer Power supply uses existing software Press written for digital modules. A select ‘inv’ or ‘nor’ list of parameters follow which are not applicable to this module. 2408 and 2404 Controller 6-23…
-
Page 95
FuLL — the decimal point Press to read position is implied, eg 100.1 ‘rES’ is transmitted as 1001. Press FuLL ‘int’ — rounded to the select ‘FuLL’ or ‘int’ nearest integer value 6-24 2408 and 2404 Controller… -
Page 96
Addr ‘Addr’ 10. Press select the address Indicates the network status:- 11. Press to read ‘nw.St’ ‘run’ = network connected nw.St and operational ‘rdy’ = network connected but not operational ‘OFF.L’ = network not connected 2408 and 2404 Controller 6-25… -
Page 97
Configuration Installation and Operation Handbook 6-26 2408 and 2404 Controller… -
Page 98
Calibrate the controller to suit the characteristics of a particular installation. Remove long term drift in the factory set calibration. User calibration works by introducing a single point, or two-point, offset onto the factory set calibration. 2408 and 2404 Controller… -
Page 99
Press until you reach ‘UCAL’. User Calibration Enable UCAL to select: • YES: Calibration enable • Calibration disabled together to go to the Exit display. Press Exit configuration to select ‘YES’ to return to Operator level. 2408 and 2404 Controller… -
Page 100
‘CAL’ display. Calibration type • FACt: Factory Calibration • USEr: User Calibration FACt to select ‘FACt’. Selecting ‘FACt’ reinstates the factory calibration and allows the application of a single fixed offset. Press continued on the next page 2408 and 2404 Controller… -
Page 101
‘iP-LiSt’ header. To protect the calibration against unauthorised adjustment, return to Operator level and make sure that the calibration parameters are hidden. Parameters are hidden using the ‘Edit’ facility described in Chapter 3, Access Levels. 2408 and 2404 Controller… -
Page 102
‘CAL’ display. Calibration type • FACt: Factory Calibration • USEr: User Calibration to select ‘USEr’. FACt Selecting ‘USEr’ enables two-point calibration. [If two-point calibration is unsatisfactory, select ‘FACt’ to return to the factory set calibration.] Press 2408 and 2404 Controller… -
Page 103
‘ip-List’ header. To perform the High-point Calibration, repeat the above procedure, selecting ‘ip1.H’ in the ‘CAL.S’ display for adjustment. Press three times. Calibration type ‘USEr’ was selected for the Low-point Calibration, and has remained selected. USEr Press 2408 and 2404 Controller… -
Page 104
‘Edit’ facility described in Chapter 3. To perform a User Calibration on Input 2, proceed as with Input 1 above, except that when ‘CAL.S-nonE’ appears, press until ‘CAL.S-iP2.L’ is obtained, then proceed as with Input 1. Repeat the procedure for ‘iP2.H’. 2408 and 2404 Controller… -
Page 105
Offset Low for Input 2 Calculated offset, in display units. OF2.H Offset High for Input 2 Calculated offset, in display units. Note: The value of each of the parameters in the above table may also be altered by using buttons. 2408 and 2404 Controller… -
Page 106
Appendix A UNDERSTANDING THE ORDERING CODE The 2408 and 2404 controllers have a modular hardware construction, which accepts up to three plug-in Input/Output modules and two communications modules to satisfy a wide range of control requirements. Two digital inputs and an optional alarm relay form part of the fixed hardware build. -
Page 107
Valve raise and lower Logic + relay Fitted unconfigured PID heat + PID cool Mode 2 + cool Logic + triac Fitted unconfigured PID heat + PID cool Mode 2 + cool Transducer P5 5Vdc 10Vdc 2408 and 2404 Controller… -
Page 108
Table A alarm options plus: German Transducer PSU Dutch Rate of change 5Vdc Spanish PDS alarms 10Vdc Heater break detect Swedish Current monitor heater brk Italian Current monitor SSR fail Program event 7 (note 7) Program END output 2408 and 2404 Controller… -
Page 109
32 to 3650 (Hoskins) W5%Re/W26%Re 10 to 2300 50 to 4172 (Englehard) W5%Re/W26%Re 0 to 2000 32 to 3632 (Bucose) Pt10%Rh/Pt40%Rh 200 to 1800 392 to 3272 Exergen K80 I.R. -45 to 650 -50 to 1200 pyrometer 2408 and 2404 Controller… -
Page 110
CTX (mode 5) (input 2 only) The example given in the coding is for 2408 PID controller, 85 to 264 Vac, logic heating, relay cooling, low alarm relay, high alarm relay, RS485 Modbus comms, PDSIO setpoint retransmission, type K thermocouple, 0 to 1000 C, Auto/manual select, second setpoint select, manual button disabled. -
Page 111
Sensor input table. For these inputs, the values entered here are the low and high setpoint limits. For process inputs, the values are the display scaling. corresponding to the minimum and maximum input values. 2408 and 2404 Controller… -
Page 112
EN 50081-2 and EN 50082-2. For more information on product compliance refer to the Technical Construction File. SERVICE AND REPAIR This controller has no user serviceable parts. Contact your nearest Eurotherm Controls agent for repair. Caution: Charged capacitors Before removing an instrument from its sleeve, disconnect the supply and wait at least two minutes to allow capacitors to discharge. -
Page 113
Due to RFI Filtering there is an earth leakage current of less than 0.5mA. This may affect the design of an installation of multiple controllers protected by Residual Current Device, (RCD) or Ground Fault Detector, (GFD) type circuit breakers. 2408 and 2404 Controller… -
Page 114
• the controller setpoint set too high. Where damage or injury is possible, we recommend fitting a separate over-temperature protection unit, with an independent temperature sensor, which will isolate the heating circuit. 2408 and 2404 Controller… -
Page 115
To ensure compliance with the European EMC directive certain installation precautions are necessary as follows: • For general guidance refer to Eurotherm Controls EMC Installation Guide, HA025464. • When using relay or triac outputs it may be necessary to fit a filter suitable for suppressing the emissions. -
Page 116
12Vdc, 8mA per channel (isolated) Digital o/p functions As per the ordering code High current output 10Amp, 264Vac resistive. This option is not available on controller from Jan-04 Triac rating 1A, 30 to 264Vac resistive (isolated) Analogue outputs 2408 and 2404 Controller… -
Page 117
RS232,2-wire,RS 485 and 4 wire RS485 modules Baud rate 1200, 2400, 4800, 9600 and 19,200 baud Slave input (isolated) Remote setpoint input with holdback to master Master output Isolated from main PV. Retransmission of setpoint, process value or output 2408 and 2404 Controller… -
Page 118
C and 5 to 90% RH non-condensing Storage temperature -10 to +70 Panel sealing IP65 Dimensions 2408: 48mm wide x 96mm high x 150mm deep 2404: 96mm wide x 96mm high x 150mm deep Weight 250g EMC standards EN61326-1 generic standards for industrial environments… -
Page 119
Technical Specification Installation and Operation Handbook 2408 and 2404 Controller… -
Page 120
DIAGNOSTICS Current flowing in a system of electrical heating elements (the ‘Load’) can be displayed on the controller by using a Eurotherm TE10 SSR fitted with intelligent current transformer, PDCTX, or an SSR or contactor with an external PDCTX. Load current monitoring and diagnostics may be used with any time proportioned output,… -
Page 121
2. Eurotherm intelligent current transformer type PD/CTX + contactor or zero voltage switching SSR 2408 or 2404 controller configured for PDS mode 2 option using logic output. This module must be fitted in module position 1. (order code M2). Controller… -
Page 122
1. Eurotherm intelligent current transformer type PD/CTX + contactor 2. 2408 or 2404 controller configured for PDS mode 5 option using logic, relay or triac output. This module must be fitted in module position 1. Digital input LB (order code M5) must be configured to accept PDCTX input as described in the configuration section of this appendix. -
Page 123
Meter mode applies to mode 5 only. If low current alarms are not configured the current displayed is a filtered instantaneous RMS value. This behaves like a damped analogue meter. It may be used in applications where the current sensor is not linked to control, for example, telemetry, indication. 2408 and 2404 Controller… -
Page 124
Ct.OP Current Indicates that the PDS input is open circuit. Transformer Mode 5 only Open Circuit Ct.Sh Current Indicates that the PDS input is short circuit Transformer Mode 5 only Short Circuit 2408 and 2404 Controller… -
Page 125
, such as control. Any one or more alarms can be attached to an output, which will operate when an alarm occurs. Contacts are rated at 2A 264Vac for operating external beacons or audible devices. 2408 and 2404 Controller… -
Page 126
SSr1 or is set to PDS mode SSr 2 as required. This is the lower PID Press to show VAL.L demand level VAL.L To set the minimum PID signal to 0% Press to show 0.0 2408 and 2404 Controller… -
Page 127
This is the maximum 100.0 output power Press To set the max output power to 100 to show 100.0 SenS Press to show This sets the output SEnS signal to normal for heating control Press to show nor 2408 and 2404 Controller… -
Page 128
Press to select AmPs The system is designed to operate in either mode 2 or mode 5 configuration only. Selecting both simultaneously will disable the output. However, mode 1 and mode 5 can be used together. 2408 and 2404 Controller… -
Page 129
To make alarm 2 = has been accepted High Current Press to show HCr Note:- The above alarms are known as SOFT ALARMS because they are indication only. D-10 2408 and 2404 Controller… -
Page 130
YES or output will not activate Repeat the above step for every alarm to be attached to the output Alarms Connected to a Relay Output Soft SEnS Alarms Output Module 2408 and 2404 Controller D-11… -
Page 131
Scalar = 100/N Where N = Turns through PDCTX Scalar Scalar Maximum Resolvable Current TE10 Determined by the maximum range of the SSR PDCTX 100A (or 100 ampere turns) Finally Exit configuration level. See Chapter 5. D-12 2408 and 2404 Controller… -
Page 132
Appendix E: Profibus Communications Introduction The 2408f and 2404f are special versions of the 2408 and 2404 controllers designed for Profibus-DP communications. The ‘standard’ 2408 or 2404 controllers cannot be upgraded to a 2408f or 2404f as the latter uses a different version of the microprocessor board. -
Page 133: Technical Specification
2408f or 2404f controller Twisted pair Intermediate stations Last Station Not connected Shield VP (+5Vdc Voltage Potential) 390Ω B (Rx/Tx +ve) 220Ω A (Rx/Tx -ve) Last station only requires 390Ω DGND (Digital ground) terminating resistors 2408f or 2404f controller 2408 and 2404 Controller…
-
Page 134
400m 200m Type B cable 1200m 1200m 1200m 600m 200m Belden B3079A meets cable A specifications, but there are other choices. For more information refer to the ‘Profibus Product Guide’ produced by the Profibus User Group. 2408 and 2404 Controller… -
Page 135
From the HOME display, press LiSt Node address Addr Press to display the node address. Press to set the desired address. 0 -126 Comms Status Stat This is a read-only diagnostic display Ready to run Comms running 2408 and 2404 Controller… -
Page 136
How many parameters can I select? How many parameters can I select? Up to 117 per node, total of inputs and outputs. What can I run it on? What can I run it on? Windows 3.1, Windows 95, or Windows NT. 2408 and 2404 Controller… -
Page 137
Ensure that the last device (not necessarily a 2404/8) in the network segment is correctly terminated (see wiring diagram). • Ensure that no devices other than those at the end of a segment have termination networks fitted. • Verify operation with a duplicate device if possible. 2408 and 2404 Controller… -
Page 138
Eurotherm Limited pursues a policy of continuous development and product improvement. The specifications in this docu- ment may therefore be changed without notice. The information in this document is given in good faith, but is intended for guidance only. Eurotherm Limited will accept no responsibility for any losses arising from errors in this document. HA025132…
Operating Instructions Temperature Programmers Eurotherm 2408CP, 2408P4, 2408CM Including 2132 and 2116 Overtemperature Controller Instructions CONTENTS section 1 2 3 4 5 6 7 8 page 2408 – Description 2408 – Basic Operation 2408 – Programming 2408 – Navigation Diagram 2408 – Options 2132/2116 – Description 2132/2116 – Operation Power Limit 2 3 4 7 8 10 10 12 See also the main manual for the furnace, oven or other product to which the controller is fitted. MC05 – 1.07 2408 Controller/Programmer 1 2408 – DESCRIPTION 1.1 Controller Nomenclature and Scope of Manual In this manual the controller is called the 2408 or the 2408CP. The manual also applies to the multi-program versions 2408P4 and 2408CM. This manual accords with software version 3.06, and to any other software versions where the instrument can be configured in accordance with the navigation diagram and other instructions given in this manual. Special customer requirements may result in changes to the available parameters and the navigation diagram. It is not possible to list all the possibilities in this manual. 1.2 2408CP Controller The Eurotherm model 2408CP is a digital instrument with PID control algorithms which may be used as a simple controller or a 16-segment programmer. The 2408P4 is a four-program model in which the programs can be stored independently or can be linked by a “call” parameter to form a single long program. The 2408CM is like the 2408P4, but is a 20-program model. The 2408 features: - Easy use as a simple temperature controller, where on setting the required temperature the controller immediately attempts to reach and maintain it. Fig.1 indicates the type of temperature response when used in this way. - By using one program segment, the control can be extended to include ramp-to-setpoint. Fig.2 shows the effect. - Alternatively the 2408 may be used as a 16-segment programmer, with each segment being a Ramp, a Step, a Dwell, or End. The program can be set to cycle if required. See fig. 3. - Optional “modules” are available, in particular: - RS232 and RS432/485 digital communications modules; - Analogue communication modules; - “PDSIO” modules for communicate with other controllers of similar or higher specification, for example to allow cascade control; - Alarm modules, which can be used to drive visible or audible alarms, or to provide volt-free contacts for customer use. The 2408 does not contain a real-time calendar, and is not subject to century-end date problems. 2 MC05 2408 Controller/Programmer 2 2408 – BASIC OPERATION 2.1 Furnace or Oven Controls Most Carbolite products are fitted with an “Instrument Switch” which cuts off power to the controller and other parts of the control circuit. See the instruction manual for the furnace or oven for the overall operating instructions. To operate the 2408 there must be power to the furnace or oven, and the Instrument switch must be on. 2.2 Eurotherm 2408CP – Outline of Operation When switched on, the controller lights up, goes through a short test routine, and then displays the measured temperature and setpoint. Depending on its state when it was last switched off it may start to control to the current setpoint of program. The output light glows or flashes to indicate that the control is occurring. The buttons and indicators are used for the following purposes: Auto/Manual Run/Hold Down & Up q&p Page / Scroll Q Page+Scroll Run & Hold Output Indicator SP2 and REM 2.3 Disabled. The unit is always in Auto mode Used to start, stop or pause a program. Short presses cause it to alternate between Run and Hold, but if it is held for 2 seconds the programmer goes into Reset mode where it behaves as a simple controller. To adjust the value of a parameter. Used to change the setpoint when the unit is being used as a simple controller (Reset mode). Holding down gives an accelerated parameter change. Allows access to the parameters within the controller; most lists and parameters are hidden from the operator as they contain factory-set values which should not be altered. A single press of the page key shows the temperature units, normally °C; further presses reveal the lists indicated in the Navigation Diagram. Allows access to the parameters within a list. A single press displays the temperature units; further presses reveal the parameters in the current list. Some parameters are display-only, others may be altered by the operator. Press together to cause an immediate return to the Home List Indicate the current mode: Run, Hold, or Reset (Reset: both lights off). Run flashes at the end of a program. Hold flashes during holdback (when the program is paused to allow the temperature to catch up with a heating or cooling rate which is too fast). OP1 indicates that the programmer is calling for heat to be supplied. OP2 is not used. Not generally used; indicate Second or Remote setpoint in use. Operation as a Simple Controller Press Run/Hold for 2 seconds to go into Reset mode. Use Down q or Up p from the Home List (i.e. when the temperature is displayed) to adjust the setpoint. The unit starts to control in the way indicated in Fig. 1. Note that to use the Ramp Rate feature, as in Fig. 2, it is necessary to create a program. See the following sections. MC05 3 2408 Controller/Programmer 3 2408 – PROGRAMMING 3.1 Creating a Program Note that a currently active segment cannot be altered - put the programmer into Hold or Reset whenever it is necessary to do so to alter a parameter. Go into Reset mode (i.e. press Run/Hold for 2 seconds) before starting to create or modify a program. Press Page / until ProG LiSt is displayed. Press Scroll Q to reveal the Holdback and Loop Count parameters. See sections 3.4 and 3.5 for a description of these. Press Scroll Q to display SEG.n (segment number); use Down q or Up p to move to the segment to be adjusted or created. Press Scroll Q to see the segment type (tYPE). Use Down q or Up p to change the required segment type – see the table. Press Scroll Q to access the parameters appropriate to the type of segment chosen – see the following table – and use Down q or Up p to alter the values. The final segment should be of type End, unless all program segments are used. Segments after End are ignored. Segment type Parameter RmP.r TGt rAtE RmP.t TGt dur 3.2 Dwel dur SteP tGt CaLL PrG.n cyc.n End End.t function The target set point for this segment The ramp rate (rate of temperature change) in °/minute The target set point for this segment The duration of the segment. The controller calculates the rate of temperature rise necessary to achieve this duration. The time in minutes to remain at the previous target temperature. A new target temperature to be achieved as quickly as possible. Only applicable to 2408P4 and 2408CM. Calls another stored program given by PrG.n as a subroutine, running it the number of times given by cyc.n. Dwel holds the temperature at the last target value. RSET returns to simple controller operation; if the setpoint is set to zero then this effectively turns the heating off. SoP sets the power to 0% – use of this is not recommended. Programming Tips Make sure the basic setpoint (see section 2.3) is set to zero to avoid unexpected heating at the end of a program. If all segments are used so that there is no End segment, then on completion the program automatically goes into Dwel. Dwell segments of length zero can be included. This is a way of allowing space for future program changes. For an example of program creation, see section 3.7. 4 MC05 2408 Controller/Programmer 3.3 Multi-program models (2408P4 & 2408CM) The Program Edit list contains the extra parameter PrG.n and the Run List contains the extra parameter PrG. These features allow selection of the program to be edited or to be run. The extra segment type cALL allows one program to call another as a subroutine; use this feature to create one or more long programs. 3.4 Holdback Holdback can be used to prevent the program from running ahead of the actual heating or cooling. In the program list, Scroll Q to the Hb parameter and use Down q or Up p to set the holdback type as follows: BAnd Lo Hi Off Holdback applies to both heating and cooling Holdback applies to heating only Holdback applies to cooling only Holdback is off Set Hb.V to the value in °C beyond which holdback is to operate. Type BAnd and a value of 10°C is often a suitable combination, if holdback is required. In this case, if the actual temperature deviates outside ±10°C from the working setpoint, the holdback lamp of the front of the controller flashes and the program is held up until the temperature comes within range again. The standard setting for holdback is Off. 3.5 Program Cycling The Loop Count parameter CYC.n can be set to control the number of times the program is run. If CYC.n = 1, the program stops at the end segment. If CYC.n = 5 (for example), the program runs 5 times: at the End segment it returns to segment 1, until the 5th time through when it stops. If CYC.n = cont, the program never ends: it cycles continuously. 3.6 Running a Program Press Run/Hold to light up the Run light. The program starts to run. To view the progress of a program from the Home list, press Scroll Q to reveal the current segment (SEG) and the total program time remaining in hours (PrG.t). For a more detailed view, press Page / to access the Run List page, and Scroll Q to see its contents as shown in the Navigation Diagram below. Provided the unit is first put into Hold mode, temporary changes may be made to parameters; these apply only until the program ends or is reset. To pause a program, press Run/Hold; the Hold light comes on. To terminate a program, press Run/Hold for 2 seconds; the Run and Hold lights go out. While the program is running, the working setpoint is shown in the lower display. MC05 5 2408 Controller/Programmer 3.7 Program example The following sequence of entries creates and runs the program shown graphically below. 1. Press page key until ProG LiSt is displayed. 2. Press scroll until CYC.n is displayed and use the arrow key to select 1. 3. Press scroll until SEG.n is displayed and use the arrow key to select 1. 4. Press scroll until tYPE is displayed and use the arrow key to select rmP.r. 5. Press scroll until tGt is displayed and use the arrow key to select 600. 6. Press scroll until rAtE is displayed and use the arrow key to select 5.0. 7. Press scroll until SEG.n is displayed and use the arrow key to select 2. 8. Press scroll until tYPE is displayed and use the arrow key to select dwEl. 9. Press scroll until dur is displayed and use the arrow key to select 60.0. 10. Press scroll until SEG.n is displayed and use the arrow key to select 3. 11. Press scroll until tYPE is displayed and use the arrow key to select rmP.t. 12. Press scroll until tGt is displayed and use the arrow key to select 400. 13. Press scroll until dur is displayed and use the arrow key to select 60.0. 14. Press scroll until SEG.n is displayed and use the arrow key to select 4. 15. Press scroll until tYPE is displayed and use the arrow key to select dwEl. 16. Press scroll until dur is displayed and use the arrow key to select 30. 17. Press scroll until SEG.n is displayed and use the arrow key to select 5. 18. Press scroll until tYPE is displayed and use the arrow key to select rmP.r. 19. Press scroll until tGt is displayed and use the arrow key to select 30. 20. Press scroll until rAtE is displayed and use the arrow key to select 5.0. 21. Press scroll until SEG.n is displayed and use the arrow key to select 6. 22. Press scroll until tYPE is displayed and use the arrow key to select End. 23. Press scroll until End.t is displayed and use the arrow key to select dwEl. 24. Press the page key until you return to the main display. 25. Press the run key. The program runs. 60m in 600°C 60m in 5°C/m 30m in 400°C 5°C/m 30°C SEG.n = 1 tYPE = rmP.r tGt = 600 rAtE = 5.0 6 SEG.n = 2 tYPE = dwEll dur = 60.0 SEG.n = 3 tYPE = rmP.t tGt = 400 dur = 60.0 SEG.n = 4 tYPE = dwEll dur = 30.0 SEG.n = 5 tYPE = rmP.r tGt = 30 rAtE = 5.0 SEG.n = 6 tYPE = End End.t = dwEll MC05 2408 Controller/Programmer 4 2408 – NAVIGATION DIAGRAM Home List 20.0 2 20.0 20.0 %C Q 20.0 %C OP 100.0 C.id SEG Multiprogram models only Run List run LiSt 5.0 LiSt LiSt Q Q Q PrG 1 PrG.n 1 OP.Hi 100.0 Addr 1 codE CYC Hb SEG Hb V 0 1 5 Do not raise the power limit (if accessible) above the design level for the product CYC.n SEG.t SEG.n tGt tYPE tYPE tGt End.t 1.0 1 Used in factory configuration; not accessible to the operator 1 rmP.r 5.0 100.0 PrG.t rAtE 5.0 home list Only if RS232/RS422/ RS485 present bAnd StYP rAtE remaining time in hours; other times are in minutes LiSt Access List ACCS Comms List cms Q 1.0 PrG.t LiSt Output List oP Q End 1 Program List ProG 2.0 dur End dwel Parameters depend on segment type 1.0 MC05 7 2408 Controller/Programmer 5 2408 – OPTIONS Because options can be ordered in a variety of combinations and for a variety of purposes, exact instructions are not given here. The full Eurotherm manual may be required to determine customer parameter settings. To reveal or hide lists and parameters in the controllers it is necessary to go into Edit mode and enter a security code. Please consult Carbolite. 5.1 Digital Communications – RS232 If the RS232 option is supplied, then the furnace is fitted with one subminiature D-socket connected to the controller comms module. RS232 is suitable for direct connection to a personal computer (PC), using a “straight through” cable as follows (the linked pins at the computer end are recommended but may not be necessary). The cable is usually 25-pin at the furnace end and 9-pin at the computer, but other alternatives are shown in parentheses. Furnace end of cable female 25-pin (9-pin) Rx 2 (3) Tx 3 (2) Com 7 (5) 5.2 RS232 Cable: furnace to PC Computer end of cable 9-pin (25-pin) male 3 (2) Tx 2 (3) Rx 5 (7) Com 7,8 (4,5) Link together 1,4,6 (6,8,20) Link together Digital Communications – RD485/422 If an RS485/422 option is supplied, then the furnace is fitted with two D-sockets. Connection between products is by “straight” cable as follows: RS485 cable: furnace to furnace female 25-pin (9-pin) 2 (3) − + 3 (2) Com 7 (5) 25-pin (9-pin) female 2 (3) − 3 (2) + 7 (5) Com RS422: furnace to furnace female 25-pin Rx+ 3 16 Rx− Com 7 Tx+ 12 13 Tx− 25-pin female 3 Rx+ 16 Rx− 7 Com 12 Tx+ 13 Tx− If a boxed KD485 RS485/422 to RS232 converter is supplied, then the connection cable from furnace to KD485 should be a “straight” cable, the same as the furnace-to-furnace cable. The connection between the KD485 and the PC should be a “crossover” cable, the same as the Furnace to PC cable in section 5.1. Note that the internal wiring of the KD485 box for the 5-wire (RS422) system includes a cross-over. 5.3 Comms Address Typically the comms address is set to 1, but this can be changed. In the case of RS422/485 and multiple instruments it is necessary to set different addresses. Press Page / a few times to get to cms (comms list), Scroll Q to Addr (address), and use Down q or Up p to alter the comms address of the controller. 8 MC05 2408 Controller/Programmer 5.4 Alarm Option When an alarm board is fitted with free contacts for customer use, the contacts are taken to a panel plug on the control panel, wired as indicated: Controller n/o contacts 2A fuse supply load The purpose of the 2 amp fuse is to guard against the connection of a mains supply to the panel plug. The instrument configuration, and parameters available to the operator, depend on the customer requirements. 5.5 Program Segment Output Where the requirement is for program segment output, an extra parameter is revealed in the Prog List. For each program segment, after the segment type and settings, the parameter OuT1 appears. This has values on and off. If the value is set to on, then the relay closes during the segment. 5.6 Remote Input and Output (Analogue Communications) When analogue communications are fitted, the contacts are taken to “banana plug” sockets on the control panel. controller Controller configuration depends on customer requirements. Remote input (when specified) may be switched on and off using the Local/Remote parameter in the controller home list, if this was made available for a particular application. Remote output does not require switching on and off. MC05 9 2132/2116 Overtemperature Controller note: the following sections apply only when overtemperature control is fitted 6 2132/2116 – DESCRIPTION The 2116 is similar to the 2132, but twice the height. The operating instructions are the same. The controller features easy setting of overtemperature setpoint, and reading of current temperature at the overtemperature sensor. The controller does not contain a real-time calendar, and is not subject to century-end date problems. To operate the controller there must be power to the furnace or oven, and the Instrument switch must be on. If a time switch is included in the furnace or oven circuit, this must be in an On period. When an overtemperature condition occurs, the controller cuts the power to a contactor, which in turn cuts power to the heating elements. Power is not restored until the controller is “reset”. Other components do not generally have power to them cut on overtemperature; oven fans usually remain running, but may not do so if other options (such as a door switch) are fitted. 7 2132/2116 – OPERATION When switched on, the controller lights up, goes through a short test routine, and then displays the overtemperature setpoint. The Page key / allows access to parameter lists within the controller; most lists and parameters are hidden and cannot be accessed by the operator because they contain factory-set parameters which should not be changed. A single press of Page / displays the temperature units, normally set to °C; further presses reveal the lists indicated in the Navigation Diagram in section 7.6. The Scroll key Q allows access to the parameters within a list. Some parameters are displayonly; others may be altered by the operator. A single press of the scroll key Q in the Home list displays the temperature units; a second press reveals the present temperature as measured by the overtemperature controller. To return to the Home list at any time, press Page / and Scroll Q together, or wait for 45 seconds. The Down q and Up p keys are used to alter the setpoint or other parameter values. 10 MC05 2132/2116 Overtemperature Controller 7.1 Basic Operation Use Down q and Up p to alter the overtemperature setpoint. This should normally be set a little above the maximum working temperature (say 15°C above). The unit is supplied at 15°C above the furnace or oven maximum working temperature. Press Scroll Q to view the present temperature as seen by the overtemperature controller. Press it twice, because the first press shows the temperature units (°C). 7.2 Overtemperature Alarm If an overtemperature condition occurs, the OP2 indicator flashes, and an alarm message 2FSH also flashes, alternating with the setpoint. Power to the heating elements is disconnected. 7.3 Resetting the Overtemperature Alarm To acknowledge the alarm press Scroll Q and Page / together. If the alarm is acknowledged while there is still an overtemperature condition, the OP2 indicator stops flashing but continues to glow. The 2FSH alarm continues to flash until the overtemperature condition is cleared (by the temperature falling), when normal operation resumes. If the alarm is acknowledged when the temperature has dropped (or after the overtemperature setpoint has been raised) such that the overtemperature condition no longer exists, then the furnace or oven immediately resumes normal operation. 7.4 Sensor Break The overtemperature cut-out system also operates if the overtemperature control thermocouple breaks or becomes disconnected. The message S.br flashes instead of 2FSH. 7.5 Audible Alarm If an audible alarm is supplied for use with the overtemperature controller, then it is normally configured to sound on overtemperature condition, and to stop sounding when the alarm is acknowledged as given in section 7.3. Note that the alarm may sound during controller start-up. It is not possible to cover in this manual other possible alarm features which may be included by customer special order. 7.6 2132/2116 Navigation Diagram Home List / 20.0 *C Q *C Q PV MC05 / Overtemperature setpoint. Use q/p to access setpoint. Present temperature. Use q/p to view the temperature. / Access List ACCS Q for factory access to lists and parameters not available to the operator codE 11 2408 Controller/Programmer 8 POWER LIMIT 8.1 Overview Depending on the furnace or oven model the power limit parameter OP.Hi (Output High) may be accessible or hidden. For silicon carbide heated furnaces the parameter is accessible to allow for compensation for element ageing (see the appropriate section in the furnace manual). In wire-heated chamber or tube furnaces, reducing the power limit is a convenient method of improving control at low temperatures, as outlined below. The power limit may be set to zero to permit demonstration of the controls without heating. In many models the power limit setting depends on the supply voltage; usually the furnace or oven manual contains details: if in doubt, contact Carbolite for advice. The power limit parameter does not apply to the overtemperature controller, if present. 8.2 Altering the value Press Page / until oP (output list) is displayed. Press Scroll Q until OP.Hi (Output High) is displayed. Press Down q or Up p once to display the value of OP.Hi and write down the value. To alter the value, use Down q or Up p. Note that setting the value to zero prevents the furnace or oven from heating. Caution: Do not increase the power limit value to a value above the design level for the oven or furnace model, or to a value above that correctly calculated for Silicon Carbide elements. The heating elements could burn out, or other damage could be caused. 8.3 Control at Low Temperatures If a product is to be used at temperatures much lower than its design maximum, control stability can often be improved by reducing the power limit. Remember to make a record of the original setting before altering the power limit. Example: It is desired to run a 1200°C furnace at 300°C. The normal control settings can be expected to cause excessive overshoot as the furnace reaches temperature. If the power limit OP.Hi is normally set to 100%, try a setting of 40%. This should greatly reduce the overshoot. (There is no firm calculation rule to get this example setting of 40% – experiment may be required to achieve a good result. Avoid power limits below about 30% – control accuracy falls off at such levels.) Copyright © 2002 Carbolite Furnaces Ltd. Thank you for reading this data sheet. For pricing or for further information, please contact us at our UK Office, using the details below. UK Office Keison Products, P.O. Box 2124, Chelmsford, Essex, CM1 3UP, England. Tel: +44 (0)1245 600560 Fax: +44 (0)1245 808399 Email: [email protected] Please note - Product designs and specifications are subject to change without notice. The user is responsible for determining the suitability of this product.
i
2408
Indicator
4.6.9
The DC Input module can only be fitted in slot 3. The following parameters appear:-
Module Parameters
Option
Identity of
id
dC.iP
module
Func
Function
nonE
rSP
Hi
Lo
Ftn
SEL
tran
<
>
<
If
Func
=
nonE no further parameters are shown.
<
>
<
>
Func
≠
nonE
When
The parameters that follow are the same as those in the
option
inPt
Refer to
HiIn
CJC
Refer to
Imp
InP.L
ImP.H
VAL.L
VAL.H
tYPe
Type of
off
calibration
Shnt
Ld.C
CmP
man
Settling
bAnd
0-
band.
99.99
(Default
0.5)
The DC input module has a single input so the above parameters are shown under list
4.6.9.1
Example: Input 1 and Input 2 are Configured for Transition
An example of the use for this could be the measurement of temperature over a wide range. The lower
temperatures may be measured by a base metal thermocouple connected to Input 1 and higher temperatures
may be measured by a pyrometer or precious metal thermocouple connected to input 2. The reason for such a
combination is to provide the most accurate readings over the full temperature range where the thermocouple
cannot be used at high temperatures and the pyrometer is too insensitive at low temperatures to provide an
accurate reading.
The thermocouple may be withdrawn, to prevent damage to it, using a high alarm set around the upper limit of
the thermocouple.
PV = Input 2 ↑
Hi.iP
Lo..iP
PV = Input 1 ↓
Part Number HA027240
Meaning
DC input
No function. Input used for monitoring and alarm only
Remote setpoint input. When selected this becomes the setpoint for deviation alarms.
<
>
FuLL
In
access level, set Remote SP Enable,
Process Value = the highest of Input 1 and input 2 is displayed in normal operation. In
normal operation the display cannot be switched between ‘front’ and ‘back’ views. The
reading shows the highest or lowest value only.
Process Value = the lowest of Input 1 and input 2 is displayed in normal operation. In
normal operation the display cannot be switched between ‘front’ and ‘back’ views. The
reading shows the highest or lowest value only.
Derived value. Process Value = (
<
>
F.2
are scalars found in the
example of differential measurement.
Select input 1 or input 2 via comms, a digital input, or in the Operator
digital input is configured use the parameter
the Operator list in Full Access use the parameter
Transition region between
Operator Level. See example 4.6.7.1.
, input 2 parameters are shown in the Input List in Full access level
<
<
>
iP
list section 4.5.2. plus the following parameter
0 to 2volt high impedance input
<
>
iP
list
Off
Shunt
Load Cell
Comparison
Manual
The indicator automatically determines when the input has become
stable by continuous sampling. When the average value between
two consecutive samples is within the settling band the indicator will
then allow calibration to take place. If readings are not stable within
this period the indicator will abort the calibration
Event set at the upper limit of the thermocouple
on input 1 to signal withdrawal.
Figure 4-8: Input 1/Input 2 Transition
Issue 5.0
Feb 2015
<
L-r
<
>
F.1
x Input 1) + (
<
>
ip
list in Full Access level. Refer to section 3.3.4. for an
<
PV.SL
<
<
>
<
>
iP.1
iP.2
and
, set by
>
<
iP
configuration list plus
During the transition stage the display
reads a combination of Input 1 and input 2.
<
If
reading will switch from input 1 to input 2
Engineering Manual
Customer settings 3B
Read only
>
<
>
rmt
=
(Remote SP selected)
<
>
<
F.2
x input 2), where
<
>
ip
list. If a
>
. If the input is selected through
>
PV.iP
<
>
<
>
Lo.IP
Hi.IP
and
>
HiLn
— the high impedance input
Customer settings
<
>
3A
only
>
<
>
Hi.iP
=
Lo.iP
the displayed
>
F.1
and
in
53
- Описание
- Конструктор заказного номера
- Отправить заявку
Описание
- Контроллеры температуры серии 2404/2408
– это универсальный контроллер с высокой стабильностью температуры или технологическим процессом, с собственной и адаптивной настройкой в размерах 1/4 DIN и 1/8 DIN. Он поставляется со стандартным 8-сегментным программатором заданных значений, с опциями для одной, четырех или двадцати программ по 16 сегментов каждый.
Он имеет модульную конструкцию, в которой размещается широкий спектр вставных модулей. Он может принимать до трех модулей ввода / вывода и двух коммуникационных модулей. Два цифровых входа и дополнительное реле сигнализации включены как часть фиксированной сборки аппаратного обеспечения. Аппаратное обеспечение конфигурируется для отопления, охлаждения, сигнализации и других функций. Опция источника питания передатчика доступна, как и опция питания преобразователя 5 или 10 В. 2404/2408 полностью настраивается на месте.
Программатор с 16 сегментами может иметь до 8 программируемых выходов, которые могут быть установлены в каждом сегменте для запуска внешних событий. Два цифровых входа могут использоваться для запуска, удержания и сброса программы. Параллельная работа нескольких программистов может быть выполнена с синхронизацией, выбранной в конце любого желаемого сегмента.
Особенности
- Высокий контроль стабильности
- До двадцати программ
- 16 сегментов
- Нагревание и охлаждение
- настраиваемая хирургия
- Нагреватель дисплей тока
- Несколько тревог на один выход
- DC ретрансляция
- Цифровая связь:
- Modbus RTU
- сеть Profibus DP
- DeviceNet® сети
Точный контроль
Расширенный алгоритм управления ПИД-регулятором обеспечивает стабильное «прямолинейное» управление процессом. Для настройки начальных значений ПИД и вычисления параметров торможения перерегулирования предусмотрен тюнер с одним выстрелом. Кроме того, адаптивный тюнер будет обрабатывать процессы с постоянно меняющимися характеристиками. При нагрузках с электрическим нагревом обратная связь по мощности используется для стабилизации выходной мощности и, следовательно, для контролируемой температуры от колебаний напряжения питания. Выделенные алгоритмы охлаждения обеспечивают оптимальное управление системами вентилятора, воды и масляного охлаждения.
Универсальный вход
Универсальная входная цепь с усовершенствованным аналого-цифровым преобразователем производит выборку входного сигнала на частоте 9 Гц и постоянно корректирует ее для дрейфа. Это дает высокую стабильность и быстрое реагирование на изменения процесса. Высокая помехоустойчивость достигается за счет отказа от приемистости 50/60 Гц и других источников шума. Также предусмотрена диагностика датчиков. Вход будет принимать все стандартные термопары, термометр сопротивления Pt100 и линейные милливольты, миллиамперы или постоянный ток.
Настраиваемая операция
Пользовательский светодиодный дисплей обеспечивает яркое, четкое отображение значения процесса и заданного значения. Тактильные кнопки обеспечивают положительную работу. Выделенные кнопки обеспечивают возможность автоматического / ручного и программного запуска / удержания. Доступ к другим параметрам прост и понятен и может быть настроен для представления только тех параметров, которые необходимо просмотреть или отрегулировать. Все остальные параметры блокируются паролем.
Сигналы тревоги
На один выход могут быть объединены до четырех сигналов тревоги. Они могут быть в полном или малом масштабе, отклонения от заданного значения, скорости изменения или аварийных сигналов отказа нагрузки. Тревожные сообщения мигают на главном дисплее. Аварийные сигналы могут быть сконфигурированы как с фиксацией или без фиксации, так и с сигнализацией типа «блокировка», что означает, что они станут активными только после того, как они впервые вошли в безопасное состояние.
Цифровые коммуникации
Контроллеры 2404/2408 доступны с широким спектром возможностей связи. EIA485 2-проводный, EIA232, EIA422 4-проводный. Доступны модули связи PDS Profibus DP или Eurotherm®, поддерживающие протоколы Modbus RTU, Profibus DP (24xxf), DeviceNet, Eurotherm Bisynch или PDSIO.
Редактор конфигурации iTools
Хотя контроллеры 2404/2408 легко и полностью настраиваются через переднюю панель, программное обеспечение для настройки iTools предлагает простой в использовании инструмент настройки ПК. ITools имеет встроенную возможность сохранять или клонировать конфигурации приборов, обеспечивая полное резервное копирование любых инженерных усилий.
Область OPC
OPC Scope — это отдельная утилита, которая позволяет проводить трендинг, ведение данных и динамический обмен данными (DDE). Это программа OPC explorer, которая может подключаться к любому OPC-серверу, который находится в реестре Windows. Доступны как данные регистрации, так и тенденции, и пользователь может отслеживать и просматривать данные в реальном времени с масштабируемой временной осью от 1 минуты до 1 месяца. Эта утилита также предлагает режим исторического обзора, и данные могут быть записаны на жесткий диск ПК, откуда они могут быть извлечены и проанализированы в электронной таблице Excel.
Конструктор заказного номера (Part Number System)
- 240#(*)
- **
- V*
- **
- **
- **
- **
- **
- **
- **
- ***
-
Номер модели
2408
:
2404
:
2408f
:
2404f
:
-
Функция и комплектность
CC
Функция:
Управление PID
Комплектность:
только контроллер
CG
Функция:
Управление PID
Комплектность:
1 × 8 сегментов программирования
CP
Функция:
Управление PID
Комплектность:
1 × 16 сегментов программирования
P4
Функция:
Управление PID
Комплектность:
4 × 16 сегментов программирования
CM
Функция:
Управление PID
Комплектность:
20 × 16 сегментов программирования
NF
Функция:
Управление включением/выключением
Комплектность:
только контроллер
NG
Функция:
Управление включением/выключением
Комплектность:
1 × 8 сегментов программирования
NP
Функция:
Управление включением/выключением
Комплектность:
1 × 16 сегментов программирования
N4
Функция:
Управление включением/выключением
Комплектность:
4 × 16 сегментов программирования
NM
Функция:
Управление включением/выключением
Комплектность:
20 × 16 сегментов программирования
VC
Функция:
Управление регулирующим клапаном
Комплектность:
позиционер клапана
VG
Функция:
Управление регулирующим клапаном
Комплектность:
1 × 8 сегментов программирования
VP
Функция:
Управление регулирующим клапаном
Комплектность:
1 × 16 сегментов программирования
V4
Функция:
Управление регулирующим клапаном
Комплектность:
4 × 16 сегментов программирования
VM
Функция:
Управление регулирующим клапаном
Комплектность:
20 × 16 сегментов программирования
-
Напряжение питания
VH
Напряжение питания:
85
…
264
В перем.
Vl
Напряжение питания:
20
…
29
В перем. / пост.
-
(-)
Модуль 1, тип:
Модуль 1, описание:
R2
Модуль 1, тип:
Модуль 1, описание:
RH
Модуль 1, тип:
Модуль 1, описание:
RU
Модуль 1, тип:
Модуль 1, описание:
R4
Модуль 1, тип:
Модуль 1, описание:
YH
Модуль 1, тип:
Модуль 1, описание:
RP
Модуль 1, тип:
Модуль 1, описание:
FH
Модуль 1, тип:
Модуль 1, описание:
FL
Модуль 1, тип:
Модуль 1, описание:
DB
Модуль 1, тип:
Модуль 1, описание:
DL
Модуль 1, тип:
Модуль 1, описание:
DH
Модуль 1, тип:
Модуль 1, описание:
L2
Модуль 1, тип:
Модуль 1, описание:
LH
Модуль 1, тип:
Модуль 1, описание:
M1
Модуль 1, тип:
Модуль 1, описание:
M2
Модуль 1, тип:
Модуль 1, описание:
LO
Модуль 1, тип:
Модуль 1, описание:
T2
Модуль 1, тип:
Модуль 1, описание:
TH
Модуль 1, тип:
Модуль 1, описание:
TU
Модуль 1, тип:
Модуль 1, описание:
D4
Модуль 1, тип:
Модуль 1, описание:
H6
Модуль 1, тип:
Модуль 1, описание:
H7
Модуль 1, тип:
Модуль 1, описание:
H8
Модуль 1, тип:
Модуль 1, описание:
H9
Модуль 1, тип:
Модуль 1, описание:
HZ
Модуль 1, тип:
Модуль 1, описание:
TK
Модуль 1, тип:
Модуль 1, описание:
TL
Модуль 1, тип:
Модуль 1, описание:
TP
Модуль 1, тип:
Модуль 1, описание:
RR
Модуль 1, тип:
Модуль 1, описание:
RD
Модуль 1, тип:
Модуль 1, описание:
RM
Модуль 1, тип:
Модуль 1, описание:
TT
Модуль 1, тип:
Модуль 1, описание:
TD
Модуль 1, тип:
Модуль 1, описание:
TM
Модуль 1, тип:
Модуль 1, описание:
LR
Модуль 1, тип:
Модуль 1, описание:
LD
Модуль 1, тип:
Модуль 1, описание:
QC
Модуль 1, тип:
Модуль 1, описание:
LT
Модуль 1, тип:
Модуль 1, описание:
GD
Модуль 1, тип:
Модуль 1, описание:
QD
Модуль 1, тип:
Модуль 1, описание:
G3
Модуль 1, тип:
Модуль 1, описание:
G5
Модуль 1, тип:
Модуль 1, описание:
-
(-)
:
R2
:
RC
:
RW
:
R4
:
YC
:
RL
:
PO
:
PE
:
FH
:
FL
:
DB
:
DL
:
DH
:
RR
:
PP
:
L2
:
LC
:
LO
:
T2
:
TC
:
TW
:
D4
:
C6
:
C7
:
C8
:
C9
:
CZ
:
TK
:
TL
:
TP
:
MS
:
D6
:
V1
:
V2
:
V3
:
V4
:
V5
:
S1
:
S2
:
S3
:
S4
:
S5
:
O1
:
O2
:
O3
:
O4
:
O5
:
Z1
:
Z2
:
Z3
:
Z4
:
Z5
:
VU
:
VS
:
VR
:
G3
:
-
(-) R2 R4 PO PE FH FL DB DL DH L2 LO T2 RR PP TK TL TP MS D5 W2 W5 WP D6 V1 V2 V3 V4 V5 S1 S2 S3 S4 S5 O1 O2 O3 O4 O5 Z1 Z2 Z3 Z4 Z5 VU VS VR -
Alarm relay
(-) RF RA LF HF SF PO PE -
(-) Y2 YM YE A2 AM AE F2 FM FE M7 PT TS OT PB DN -
Comms 2
(-) M6 RS M7 PT TS OT -
Руководство
(-) FRA GER NED SPA SWE ITA
Примеры заказа:
Схема изоляции контроллера
Отправленная нашим заказчикам продукция:
Operation & User’s Manual for Eurotherm 2408i Measuring Instruments, Temperature Controller (66 pages)
Specifications:1089/1089048-2408i.pdf file (31 May 2023) |
Accompanying Data:
Eurotherm 2408i Measuring Instruments, Temperature Controller PDF Operation & User’s Manual (Updated: Wednesday 31st of May 2023 07:57:33 PM)
Rating: 4.1 (rated by 87 users)
Compatible devices: 4103C, 2132, 2116, 3116 PID, 3200, 2216L, 3116, 2216e.
Recommended Documentation:
Text Version of Operation & User’s Manual
(Ocr-Read Summary of Contents of some pages of the Eurotherm 2408i Document (Main Content), UPD: 31 May 2023)
-
58, Engineering Manual 2408 i Indicator 56 …
-
46, Eurotherm 2408i Engineering Manual 2408 i Indicator 4.5.6 Digital inputs 1 and 2 Configuration or LA Digital input 1 O…
-
43, Eurotherm 2408i 2408 i Indicator Engineering Manual 4.5.3 Alarm Configuration Alarms are used to alert an operator when the process value has exceeded a pre-set level o…
-
48, Engineering Manual 2408 i Indicator 4.5.8 Relay Output 1 Configuration The controller can be supplied so that Relay 1 will operate when a partic…
-
19, 2408 i Indicator Engineering Manual Summary A. Press to st…
-
38, Engineering Manual 2408 i Indicator 4.3 Location of Parameters – From Indicator Block Diagram The indicator consists of a number of in…
-
Eurotherm 2408i User Manual
-
Eurotherm 2408i User Guide
-
Eurotherm 2408i PDF Manual
-
Eurotherm 2408i Owner’s Manuals
Recommended: DSRV 9703C, 32E66, AE122BCAAA
-
Doepke Dupline DTS 1
3931187/2009.02/GDoepkeDuplineTemperatursensor DTS 1DTS 1 Temperature SensorBedienungsanleitungOperating InstructionsInhaltsverzeichnis1. Allgemeines………………………… 22. Wichtige Hinweise vorab………. 23. Kodierung…………………………… 24. Inbetriebnahme …………………… …
Dupline DTS 1 8
-
aci SST2630
Automation Components, Inc.2305 Pleasant View Road | Middleton, WI 53562Phone: 1-888-967-5224 | Website: workaci.comPage 1Version: 5.0I0000684The Probe sensor may be mounted using a 1/4” mounting clip (ACI Item #108169) on walls or with cable ties along pipes.PIPE MOUNTINGFor best accuracy and …
SST2630 4
-
Bodmer Ton SE 9-6
Bodmer Ton AG Holzrüti 1 CH-8840 Einsiedeln Phone +41 55 418 28 58 E-Mail [email protected] Website www.bodmer-ton.ch 1 Instruction Manual Temperature Controller SE 9-6 1. Introduction ……………………………………………………………………………………………………….. …
SE 9-6 10
-
Danfoss ECL Comfort 210
InstallationGuideECLComfort210/310,applicationA237/A3371.0TableofContents1.0TableofContents………………………………………..1� …
ECL Comfort 210 122
Operating Impressions, Questions and Answers:
- Page / 13
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
MC05 – 1.07
Operating Instructions
Temperature Programmers
Eurotherm 2408CP, 2408P4, 2408CM
Including 2132 and 2116 Overtemperature Controller Instructions
See also the main manual for the furnace, oven or other product to
which the controller is fitted.
ONTENTS
section page
1 2408 – Description 2
2 2408 – Basic Operation 3
3 2408 – Programming 4
4 2408 – Navigation Diagram 7
5 2408 – Options 8
6 2132/2116 – Description 10
7 2132/2116 – Operation 10
8 Power Limit 12
Summary of Contents
More documents for Recording Equipment Eurotherm 2408
Показаны 1 — 2 из 2 товаров
Показаны 1 — 2 из 2 товаров
Доставка eurotherm 2404 2408 manual
Оформив покупку у нас Вы 100% заберете свой заказанный товар в самые короткие сроки !
Ведь купить товар из-за рубежа не так просто, а мы с легкостью организуем почтовую пересылку по всей России и СНГ (доставка организована в Казахстан,Украину,Беларусию и т.д.) .
На этой странице указаны особенности и техническая спецификация товара, доставка бесплатна и цена (указана в рублях) на все товары на нашем сайте окончательна (доплачивать при получении посылки не нужно).
Страхование всех посылок заказанных у нас является гарантией получения товара , а грамотные специалисты помогут Вам купить eurotherm 2404 2408 manual без особых проблем и получить только радость от покупки .
Вы также можете воспользоваться нашим онлайн-каталогом для поиска других товаров (более 300 миллионов товаров со всего мира ) , которые мы тоже можем заказать для Вас . Уже более 60 000 человек оценили убоство работы с нашей компанией.
Купить eurotherm 2404 2408 manual
Если Вы ищите сайт, где можно найти много разных eurotherm 2404 2408 manual то Вы попали по адресу! У нас можно купить с доставкой по России и СНГ (мы осуществляем доставку в Беларусию,Украину,Казахстан и т.д.) .
Все посылки заказываемые через нашу компанию застрахованы и это 100% гарантия получения товара . Квалифицированная служба поддержки поможет Вам, проконсультирует по потребительским свойствам , что позволит получить только радость и хорошие эмоции от покупки.
Если Вы пролистаете страницу Выше, то найдете таблицу,где указаны все технические характеристики и особенности.
Доставка в Ваш город бесплатна, а ценовое предложение указанно в рублях (на все товары в нашем огромном онлайн-каталоге) — окончательна(доплата при получении заказа на почте не потребуется).
Мы занимаемся доставкой товаров из-за рубежа уже более 10 лет , что позволяет со 100% гарантией утверждать ,
что мы купим eurotherm 2404 2408 manual и сделаем его пересылку до Вас быстрой и безопасной, без затягивания сроков и любых проблем.
Воспользуйтесь нашим онлайн-каталогом, чтобы найти другие товары т.к. в них находится больше чем 300 000 000 лотов со всего мира,
которые мы тоже можем заказать для Вас.
Гарантия на eurotherm 2404 2408 manual
Купив у нас Вы гарантированно получите свою покупку как указано в описании и в самые короткие сроки! Мы организуем доставку по всей России и СНГ ( доставка в Беларусию,Украину,Казахстан и т.д.) .
Вы также можете воспользоваться нашим каталогом для поиска других товаров ( более 300 миллионов товаров со всего мира ) , которые мы тоже можем заказать для Вас.
Мы предлагаем супер-цену на eurotherm 2404 2408 manual, а также Вы бесплатно получаете возможность воспользоваться нашей расширенной программой защиты покупателя и бесплатной доставкой. Цена указана в рублях на все товары в этой категории окончательна .
Все заказы застрахованы на 5 000 000 (пять миллионов рублей) в СК «Гелиос».
Случайный отзыв о нашей работе
Товар качественный, пришел в срок , рекомендую.. Автор Елена. Дата 2022-04-30. Населенный пункт: Пенза
Installation and operationhandbook
2404
2408
CONTROL SETPOINTPROGRAMMER
ENG
Installation and Operation Handbook Contents
Issue 10.0 Nov-04 Applies to 2408 and 2404 controller software version 4.0 i
MODELS 2408 and 2404 PID CONTROLLERS
INSTALLATION AND OPERATION HANDBOOK
Contents Page
Chapter 1 INSTALLATION ………………………………………………………..1-1
Chapter 2 OPERATION …………………………………………………………….2-1
Chapter 3 ACCESS LEVELS……………………………………………………..3-1
Chapter 4 TUNING……………………………………………………………………4-1
Chapter 5 PROGRAMMER OPERATION ……………………………………5-1
Chapter 6 CONFIGURATION …………………………………………………….6-1
Chapter 7 USER CALIBRATION ………………………………………………..7-1
Appendix A UNDERSTANDING THE ORDERING CODE………………. A-1
Appendix B SAFETY and EMC INFORMATION……………………………. B-1
Appendix C TECHNICAL SPECIFICATION……….……………………C-1
Appendix D LOAD CURRENT MONITORING AND DIAGNOSTICS..D-1
Appendix E PROFIBUS COMMUNICATIONS….……………………….E-1
“This product is covered by one or more of the following US Patents:
5,484,206; Additional patents pending.
PDS and INSTANT ACCURACY are trademarks of Eurotherm.”
Issue 10 of this handbook applies to software version 4.
Contents Installation and Operation Handbook
ii Issue 10.0 Nov-04 Applies to 2408 and 2404 controller software version 4.0
Enhancements to Software Version 4
The following enhancements have been added to software versions 4.
• Isolated Single Logic Output Module
• Transducer Power Supply Module to provide 5 or 10Vdc to an external transducer. (Not intended for melt pressure control)
• DeviceNet communications
• Linear over range limits are +5% of high instrument range and –5% of low instrument range for all process input ranges (i.e. 0-20mA, 4-20mA, 0-10V)
• Sensor break or input open circuit faults are detected on all analogue inputs (PV1.PV2 and remote input channels)
• PV2 alarm, full scale high and low limits default to maximum and minimum display limits
• Deviation alarms are not inverted when direct acting control is selected. Alarm behaviour when using reverse acting control is unchanged
• The PD track valve positioning parameter (Pd.tr) has been removed
Controllers Affected:-
Standard controllers – which include programmers with up to 4 programs
Version 4.11 or later
Setpoint programming controllers with up to 20 programs
Version 4.61 or later
Profibus controllers – which include programmers with up to 4 programs
Version 4.32 or later
• The 10Amp output relay in module 4 is not available on controllers supplied after Jan 04
Related Information
• DeviceNet Communications Handbook part no. HA027506 which includes the parameter address map.
• Profibus Communications Handbook part no. HA026290 • EMC (Electromagnetic Compatibility) Installation Guide, part no. HA025464 These are available on www. eurotherm.co.uk.
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-1
Chapter 1 INSTALLATION
Figure 1-1 2408 1/8 DIN controller
Figure 1-2 2404 1/4 DIN controller
Panel retaining clips
Ratchets
Sleeve Terminal covers
Label
Latching ears Panel sealing gasket
Display screen
Panel retaining clips
Ratchets Sleeve Terminal covers
Label
Latching ears Panel sealing gasket
Display screen
Installation Installation and Operation Handbook
1-2 2408 and 2404 Controller
Outline dimensions Model 2408
Outline dimensions Model 2404
The electronic assembly of the controller plugs into a rigid plastic sleeve, which in turn fits into the standard DIN size panel cut-out shown in Figures 1-3 and 1-4.
2408
OP 1 OP2
SP2 REM
AUTOMAN
RUNHOLD
Figure 1-3 Outline dimensions of Model 2408 controller
150mm
5.91in
48mm
1.89in
96mm 3.78in
150mm
5.91in 96mm 3.78in
96mm 3.78in
2404
OP 1 OP2
SP2 REM
AUTOMAN
RUNHOLD
Panel cut-out
92 x 92 mm
3.62 x 3.62 in
-0 +0.8
-0 +0.03
Panel cut-out
92 x 45mm
3.62×1.77in
-0 +0.8
-0 +0.6
-0 +0.03
-0 +0.02
38mm (1.5in)
10mm (0.4in)
(Not to scale)
Recommended minimum spacing of controllers
Recommended minimum spacing of controllers
38mm (1.5in)
10mm (0.4in)
(Not to scale)
Figure 1-4 Outline dimensions Model 2404 controller
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-3
INTRODUCTION
Models 2408 and 2404 are high stability, temperature or process controllers with self and adaptive tuning. They have a modular hardware construction which accepts up to three plug-in Input/Output modules and two interface modules to satisfy a wide range of control requirements. Two digital inputs and an optional alarm relay are included as part of the fixed hardware build. The instruments are available as: • standard controllers — which include a basic 8-segment programmer Models 2408/CC and 2404/CC • setpoint programming controllers: Models 2408/CP, P4, CM and 2404/CP, P4, CM • motorised valve controllers — which include a basic 8-segment programmer Models 2408/VC and 2404/VC • setpoint programming motorised valve controllers: Models 2408/VP, V4, VM and 2404/VP, V4, VM
Before proceeding, please read the chapter called, Safety and EMC Information.
Controller labels
The labels on the sides of the controller identify the ordering code, the serial number, and the wiring connections.
Appendix A, Understanding the Ordering Code, explains the hardware and software configuration of your particular controller. MECHANICAL INSTALLATION To install the controller
1. Prepare the control panel cut-out to the size shown in Figure 1-3, or 1-4.
2. Insert the controller through the panel cut-out.
3. Spring the upper and lower panel retaining clips into place. Secure the controller in position by holding it level and pushing both retaining clips forward.
Note: If the panel retaining clips subsequently need removing, in order to extract the controller from the control panel, they can be unhooked from the side with either your fingers, or a screwdriver. Unplugging and plugging-in the controller
If required, the controller can be unplugged from its sleeve by easing the latching ears outwards and pulling it forward out of the sleeve. When plugging the controller back into its sleeve, ensure that the latching ears click into place in order to secure the IP65 sealing.
Installation Installation and Operation Handbook
1-4 2408 and 2404 Controller
NEW SLEEVE DESIGN MKIII
From Jan-03 an improved design of 1/8 DIN long sleeve is shipped with all new 2408 controllers and indicators. (The month and year of manufacture are shown in the last two pairs of digits of the instrument serial number).
Details
A new sealing gasket will be fitted onto the instrument bezel !. This gasket replaces the gasket which was moulded into the front of the sleeve of all previous instruments. The gasket previously moulded into the sleeve where it fits behind the panel is now supplied as a separate item «.
Reasons for the Change
This change is to ensure that IP65 sealing is reliably achieved and less physical effort is required to insert the instrument into the new sleeve.
Recommendations
1. An instrument delivered after Jan 03 should be used with the sleeve supplied 2. If the instrument is required to replace one already in use, the existing sleeve should
also be replaced 3. A new instrument can be fitted into an existing sleeve by carefully removing gasket
! but IP65 sealing will not be maintained 4. An existing instrument can be fitted into a new sleeve but IP65 sealing will not be
maintained It is, however, possible to achieve IP65 sealing for 3 and 4 above. A gasket kit is available by quoting Part No SUB24/GAS2408. Then:-
5. To fit a new instrument in an older sleeve carefully remove gasket !. Replace it with the thinner (1.25mm) gasket from the kit
6. To fit an existing instrument into a new sleeve fit the thicker (1.6mm) gasket from the kit between the instrument and the sleeve
The seal » supplied as a separate item with a new instrument, should be placed over the sleeve prior to mounting it through the panel cut out as shown below:-
Panel
New Instrument
Sleeve seal » (supplied as a separate item)
Instrument sleeve
New gasket ! fitted onto bezel
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-5
ELECTRICAL INSTALLATION
This section consists of five topics: • Rear terminal layouts • Fixed connections • Plug-in module connections • Typical wiring diagrams • Motorised valve connections.
WARNING You must ensure that the controller is correctly configured for your application. Incorrect configuration could result in damage to the process being controlled, and/or personal injury. It is your responsibility, as the installer, to ensure that the configuration is correct. The controller may either have been configured when ordered, or may need configuring now. See Chapter 6, Configuration.
Model 2408 rear terminal layout
Figure 1-5 Rear terminal layout − Model 2408 * The ground connection is provided as a return for internal EMC filters. It is not required for safety purposes, but must be connected in order to satisfy EMC requirements.
N
L
V+
VI
V-
Line
Neutral
Ground*
2D
2B
2A
2C
3D
3B
3A
3C
1D
1B
1A
1C
M O D U L E 1
M O D U L E
3
M O D U L E 2
JF
JD
JE
C O M M S 2
Common
Input 1
Input 2
85 to 264Vac
LC
LA
LB
AC
AA
AB Alarm relay
HF
HD
HE
C O M M S 1
HB
HA
HC
JB
JA
JC
+
−
+ PV −
RTD/Pt100
T/C
Note: The plug-in sleeve supplied with high voltage controllers are keyed to prevent a low voltage unit being inserted into them.
20 − 29Vac/dc
Ground*
24
24
Low voltage supply
Installation Installation and Operation Handbook
1-6 2408 and 2404 Controller
All electrical connections are made to the screw terminals at the rear of the controller. If you wish to use crimp connectors, the correct size is AMP part number 349262-1. They accept wire sizes from 0.5 to 1.5 mm2 (16 to 22 AWG). The terminals are protected by a clear plastic hinged cover to prevent hands, or metal, making accidental contact with live wires.
Rear terminal layouts
The rear terminal layouts are shown in Figures 1-5 and 1-6. The right-hand column carries the connections to the power supply, digital inputs 1 and 2, alarm relay and sensor input. The second and third columns from the right carry the connections to the plug-in modules. The connections depend upon the type of module installed, if any. To determine which plug-in modules are fitted, refer to the ordering code and wiring data on the controller side labels.
Model 2404 rear terminal layout
Figure 1-6 Rear terminal layout − Model 2404
RTD/Pt100
N
L
V+
VI
V-
Line
Neutral
Ground*
2D
2B
2A
2C
3D
3B
3A
3C
1D
1B
1A
1C
M O D U L E 1
M O D U L E 3
M O D U L E 2
HF
HD
HE
C O M M S 1
JF
JD
JE
C O M M S 2
Common
Input 1
Input 2
85 to 264Vac
LC
LA
LB
AC
AA
AB Alarm relay
−
+
PV −
T/C
HB
HA
HC
JB
JA
JC
+
5B
5A
4D
4B
4A
4C
20 − 29Vac/dc
Ground*
24
24
Low voltage supply
6D
6C
6B
5D
5C
6A
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-7
Sensor input connections
The connections for the various types of sensor input are shown below.
Fig 1-7 Sensor input connections
PLUG-IN MODULE CONNECTIONS
Module 1, 2 and 3
Module positions 1, 2 and 3 are plug-in modules. They can be either two terminal modules of the types shown in Figure 1-7, or four terminal modules of the types shown in Table 1-1.
The tables show the connections to each module and the functions that they can perform. Module 1 is normally used for heating and module 2 for cooling although the actual functions will depend upon how the controller has been configured.
PDS modes
Table 1-8 refers to PDS modes 1 and 2. PDS stands for ‘Pulse Density Signalling’ Input/Output. This is a proprietary technique for bi-directional transmission of analogue and digital data over a simple 2-wire connection. PDS 1 mode uses a logic output module to control aTE10S solid state relay and provides a load failure alarm. PDS 2 mode uses a logic output module to control a TE10S solid state relay, provide load/SSR failure alarms, and read back the load current for display on the controller.
VI
V+
V-
VI
V+
V-
VI
V+
V-
VI
V+
V-
Thermocouple Resistance thermometer
mA input Volts or mV inputs
+
— PV
2.49Ω current sense resistor
Installation Installation and Operation Handbook
1-8 2408 and 2404 Controller
Two terminal modules Note: Module 1 is connected to terminals 1A and 1B Module 2 is connected to terminals 2A and 2B Module 3 is connected to terminals 3A and 3B.
Terminal identity
Module type A B C D Possible functions
Relay: 2-pin
(2A, 264 Vac max.)
Unused Heating, cooling, alarm, program event, valve raise, or valve lower
Logic — non-isolated
(18Vdc at 20mA)
++++ −−−−
Unused Heating, cooling, PDSIO mode 1, PDSIO mode 2,
program event
Triac
(1A, 30 to 264Vac)
Unused Heating, cooling, program event, valve raise, or valve lower
DC output: — non-isolated
(10Vdc, 20mA max.)
++++ − Unused Heating, or cooling, or
retransmission of PV, setpoint, or control output
Table 1-1 Two terminal module connections
Snubbers
The relay and triac modules have an internal 15nF/100Ω ‘snubber’ connected across their output, which is used to prolong contact life and to suppress interference when switching inductive loads, such as mechanical contactors and solenoid valves.
WARNING When the relay contact is open, or the triac is off, the snubber circuit passes 0.6mA at 110Vac and 1.2mA at 240Vac. You must ensure that this current, passing through the snubber, will not hold on low power electrical loads. It is your responsibility as the installer to ensure that this does not happen. If the snubber circuit is not required, it can be removed from the relay module (BUT NOT THE TRIAC) by breaking the PCB track that runs crosswise, adjacent to the edge connectors of the module. This can be done by inserting the blade of a small screwdriver into one of the two slots that bound it, and twisting.
Line Load
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-9
Four terminal modules Note: Module 1 is connected to terminals 1A, 1B, 1C and 1D Module 2 is connected to terminals 2A, 2B, 2C and 2D Module 3 is connected to terminals 3A, 3B, 3C and 3D
Module type Terminal identity Possible functions
A B C D
Relay: changeover (2A, 264 Vac max.)
Heating, cooling, alarm, or program
event output
DC control: Isolated (10V, 20mA max.) ++++ −−−−
Heating, or cooling
24Vdc transmitter supply
+ − To power process inputs
Potentiometer input 100Ω to 15KΩ
+0.5Vdc 0V Motorised Valve Position feedback
DC retransmission + − Retrans. of setpoint, or process value
DC remote input or Process Value 2 (Module 3 only)
0-10Vdc RT source ±100mV 0-20mA
COM Remote Setpoint Second PV
Dual output modules
Dual relay (2A, 264 Vac max.)
Heating + cooling Dual alarms Valve raise &
lower
Dual Triac (1A, 30 to 264Vac)
Heating + cooling
Valve raise & lower
Dual logic + relay (Logic is non-isolated) + −
Heating + cooling
Dual Logic + triac (Logic is non-isolated) + −
Heating + cooling
Triple logic input and output modules — see ratings on the next page
Triple contact input Input 1 Input 2 Input 3 Common
Triple logic input Input 1 Input 2 Input 3 Common
Triple logic output Output 1 Output 2 Output 3 Common Program events
N/C N/O
Line Load Line Load
Line Load
Installation Installation and Operation Handbook
1-10 2408 and 2404 Controller
Module type Terminal identity Possible functions
A B C D
Isolated Logic Output
+ — This is a fully isolated module which can be fitted in all three module slots. It may be used for heating, cooling or events outputs up to 18Vdc at 20mA.
Transducer Power Supply
+ — This provides fully isolated 5 or 10Vdc to power external transmitters up to 20mA. It can be fitted in module slots 1 and 2.
Table 1-2 Four terminal module connections
Connections for Process Value 2 in module position 3
The diagrams below show the connections for the various types of input. The input will have been configured in accordance with the ordering code.
Triple Logic Input and output ratings
1. Triple logic input (current sinking) OFF state: −3 to 5Vdc ON state: 10.8 to 30Vdc(max), at 2 to 8mA
2. Triple contact closure or open collector transistor input
Internally generated switching Vdc & mA: 15 to 19Vdc at 10 to 14mA OFF state >28KΩ input resistance OFF state voltage >14Vdc ON state <100Ω resistance ON state voltage <1.0Vdc
3. Triple logic output (current sourcing) OFF state output 0 to 0.7Vdc. ON state output 12 to 13Vdc, at up to 8mA.
Thermocouple
3B
3C
3D
3A
+
−
Current sense
resistor 2.49Ω
mA input
3B
3C
3D
3A
+
−
Resistance thermometer
3B
3C
3D
3A
Volts or mV inputs
+
−
0-1.6Vdc High Impedance
or mVdc
3B
3C
3D
3A
10V inputs
+
−
0-10Vdc 3B
3C
3D
3A
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-11
COMMUNICATION MODULES 1 AND 2
All 2408 and 2404 controllers can be fitted with up to two plug-in communications modules. Only one of the two modules can be for serial communications and this will normally be installed in position COMMS 1 (although it is possible to install the serial communications module in position COMMS 2. Serial communications may be configured for either Modbus or EI bisynch protocol. It is also possible to fit a PDS module in one or other of these positions. Possible module types are shown in the table below.
Communications module 1 Terminal identity (COMMS 1)
Module type HA HB HC HD HE HF
2-wire EIA-485 serial communications
− − − Common A (+) B (−)
EIA-232 serial communications
− − − Common Rx Tx
4-wire EIA-485 serial communications
− A′ (Rx+)
B′ (Rx−)
Common A (Tx+)
B (Tx−)
PDS Setpoint retransmission − − − − Signal Common
Communications module 2 Terminal identity (COMMS 2)
Module type JD JE JF
PDS Setpoint retransmission − Signal Common
PDS Setpoint input − Signal Common
Table 1-3 Communication modules 1 and 2 connections
Installation Installation and Operation Handbook
1-12 2408 and 2404 Controller
Wiring of 2-wire EIA-485 serial communications link
Com
Note:All resistors are 220 ohm 1/4W carbon composition.Local grounds are at equipotential. Where equipotential is not available wire intoseparate zones using a galvanic isolator.Use a repeater (KD845) for more than 32 units.
A
B
PC
Eurotherm UniversalCommunications Interface
KD485
RXTXCom
Com TXRX
Up to 32 S2000 controllers orInterface Units maybe included on the network
232
Com B A
Com
A
BCom
A
B
Com
A
B
Local Earth
LocalGroundZone 1
LocalGroundZone 2
Area 1 Com
AB
E
F
D
LocalEarth
HE
HF
HD
Series 2000Controller
HE
HF
HD
Series 2000Controller
For reasons of safetydo not connect tolocal earth here.
LocalEarth
LocalEarth
LocalEarth
LocalEarth
LocalEarth
HE
HF
HD
Series 2000Controller
GalvanicIsolationBarrier
LocalGroundZone 1
LocalGroundZone 1
LocalGroundZone 1
Figure 1-9 EIA-485 wiring
2-wire EIA-485 is a connection which allows up to 32 controllers to be multi-dropped from a single communications link over a distance of up to 1.2Km. To ensure reliable operation of the communications link, (without data corruption due to noise or line reflections) the connections between the controller should be made using a twisted pair of wires inside a screened cable with the connections terminated with resistors in the manner shown in this diagram. This diagram also shows the use of a KD485 converter to connect the EIA-485 link into a standard EIA-232 computer port.
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-13
DeviceNet
Instruments fitted with software versions 4 onwards can be fitted with DeviceNet communications. The following shows the wiring connections for DeviceNet.
Terminal Reference
CAN
Label
Color
Chip
Description
HA V+ Red DeviceNet network power positive terminal. Connect the red wire of the DeviceNet cable here. If the DeviceNet network does not supply the power, connect to the positive terminal of an external 11-25 Vdc power supply.
HB CAN_H White DeviceNet CAN_H data bus terminal. Connect the white wire of the DeviceNet cable here.
HC SHIELD None Shield/Drain wire connection. Connect the DeviceNet cable shield here. To prevent ground loops, ground the DeviceNet network in only one location.
HD CAN_L Blue DeviceNet CAN_L data bus terminal. Connect the blue wire of the DeviceNet cable here.
HE V- Black DeviceNet network power negative terminal. Connect the black wire of the DeviceNet cable here. If the DeviceNet network does not supply the power, connect to the negative terminal of an external 11-25 Vdc power supply.
HF Connect to instrument earth
Note: Power taps are recommended to connect the DC power supply to the DeviceNet trunk line. Power taps include:
• A Schottky Diode to connect the power supply V+ and allows for multiple power supplies to be connected.
• 2 fuses or circuit breakers to protect the bus from excessive current which could damage the cable and connectors.
• The earth connection, HF, to be connected to the main supply earth terminal.
Installation Installation and Operation Handbook
1-14 2408 and 2404 Controller
Example of Devicenet Wiring
To configure DeviceNet Communications see Chapter 6.
HA
HB
HC
HD
HE
HF
2400 Controller
(SLAVE) Address 11
V+
CAN-H
CAN-L
Drain
V-
V+ 5
CAN-H 4
CAN-L 2
Drain 3
V- 1
Red
Wht
Blu
Blk
* Fit 121! resistor to last instrument in the
chain
Network Supply
24Vdc ( +1%) 250mV p-p
Ripple
HA
HB
HC
HD
HE
HF
2400 Controller
(SLAVE) Address N+1
V+
V- V-
V+
Typical Interface Card (MASTER)
Daisy chain to further
instruments
121! terminating resistor required if not
fitted internally L
N
E
L
N
E
*
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-15
ProfiBus Wiring
Controllers supplied with model numbers 2408f and 2404f are fitted with ProfiBus communications modules fitted in the H slot. Further details of ProfiBus communications is given in Appendix E and the ProfiBus Communications handbook part number HA026290. This handbook can be downloaded from www.eurotherm.co.uk.
SHIELD
Station 1HA
HB
HC
HD
HE
HF
Shield
VP (+5Vdc Voltage Potential)
B (Rx/Tx +ve)
A (Rx/Tx -ve)
DGND (Digital ground)
Not connectedB
390Ω
Last StationHA
HB
HC
HD
HE
HF
Shield
VP (+5Vdc Voltage Potential)
B (Rx/Tx +ve)
A (Rx/Tx -ve)
DGND (Digital ground)
Not connected
Intermediate stations
Last station only requiresterminating resistors
390Ω
220Ω
A
BA
BA
2408f or 2404f controller
2408f or 2404f controller
Twistedpair
Twistedpair
Installation Installation and Operation Handbook
1-16 2408 and 2404 Controller
TYPICAL WIRING DIAGRAM
Fig 1-10 Typical wiring diagram, Model 2408 Controller For logic drive capability see following chart:-
N
L
V+
VI
V-
2D
2B
2A
2C
3D
3B
3A
3C
1D
1B
1A
1C
M O D U L E 3
HF
HD
HE
C O M M S 1
JF
JD
JE
LC
LA
LB
AC
AA
AB
Cooling Power Fuse
1A(T)
Heating power fuse (load dependent)
Cooling Solenoid
Heater
T/C
+
—
+ PV —
Logic heating output
Triac cooling output
Line Neutral
Controller Fuse 2A(T)
Solid State Relay *
+
−
C O M M S 2
HB
HA
HC
Installation and Operation Handbook Installation
2408 and 2404 Controller 1-17
Logic Drive Fan Out
The logic outputs from the 2400 series controllers are capable of driving more than one solid state relay (SSR) in series or parallel. The following table shows the number of SSRs which can be driven depending on type of SSR. S = Series; P = Parallel.
Drive mA
SVDA RVDA TE10S 425S
Logic DC
Logic DC
Logic DC
Logic 10V
Logic 24V
Logic 20mA
Logic [email protected]
4S 6P 4S 3P 3S 2P 3S 3P 1S 2P 6S 1P
Triple logic
[email protected] 3S 3P 2S 1P 2S 1P 2S 1P 1 4S 1P
450 TC1027
CE TE200S TC2000
CE RS3D
A Standard TTL Multi-
drive Logic V Logic
DC Logic DC
Logic DC
Logic 2S 3P 1S2P 6S 1P 3S 3P 3S 3P 3S 1P 4S 2P Triple logic
1 1 4S 1P 2S 1P 2S 1P 0 0
Installation Installation and Operation Handbook
1-18 2408 and 2404 Controller
MOTORISED VALVE CONNECTIONS
Motorised valves will normally be wired either to dual relay, or dual triac, output modules installed in the Module 1 position, or to single channel relay and triac outputs installed in Module positions 1 and 2. In the latter case, the convention is to configure output 1 as the raise output and output 2 as the lower output. Depending on the configuration, control of the valve is achieved in one of three ways: 1. With no position feedback potentiometer. 2. With a feedback potentiometer used to monitor the valve’s position. It does not
influence the control. 3. With a feedback potentiometer, where the valve’s position is controlled in response to the
signal from it.
Fig 1-11 Motorised valve connections
N
L
V+
VI
V-
Line
Neutral
Ground
++++
−−−−
++++
PV
−−−−
2D
2B
2A
2C
3D
3B
3A
3C
1D
1B
1A
1C
M O D U L E 2
HF
HD
HE
C O M M S 1
JF
JD
JE
C O M M S 2
Common
Input 1
Input 2
85 to 264Vac
LC
LA
LB
AC
AA
AB Alarm relay
Motor supply
Motorised valve
R A I S E
L O W E R
Dual relay, or
triac, output module
RTD/Pt100
HB
HA
HC
Motor Feedback
Potentiometer (Optional)
++++
−−−−
Pot Input
Module
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-1
Chapter 2 OPERATION
This chapter has nine topics:
• FRONT PANEL LAYOUTS
• BASIC OPERATION
• OPERATING MODES
• AUTOMATIC MODE
• MANUAL MODE
• PARAMETERS AND HOW TO ACCESS THEM
• NAVIGATION DIAGRAM
• PARAMETER TABLES
• ALARMS
Operation Installation and Operation Handbook
2-2 2408 and 2404 Controller
FRONT PANEL LAYOUTS
2408
OP 1 OP2
SP2 REM
AUTOMAN
RUNHOLD
Figure 2-1 Model 2408 front panel layout
2404
OP 1 OP2
SP2 REM
AUTOMAN
RUNHOLD
Figure 2-2 Model 2404 front panel layout
Output 1
Setpoint 2
Auto/Man button
Auto mode
Manual mode
Page Button
Scroll Button
Down Button
Remote setpoint / comms (flashing)
Output 2
Upper
Lower readout
Program running
Program in Hold
Up Button
Remote setpoint/ comms(flashing)
Output 2
Upper readout
Lower readout
Program running
Run/Hold button
Program in Hold
Up Button
Output 1
Setpoint 2
Auto/Man button
Auto mode
Manual mode
Page Button
Scroll Button
Down Button
2408
2404
OP 1 OP 2
OP 1 OP 2
SP2 REM
SP2 REM
Run/Hold
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-3
Button or indicator
Name Explanation
OP1
Output 1 When lit, it indicates that the output installed in module position 1 is on. This is normally the heating output on a temperature controller.
OP2
Output 2 When lit, it indicates that the output installed in module position 2 is on. This is normally the cooling output on a temperature controller.
SP2 Setpoint 2 When lit, this indicates that setpoint 2, (or a setpoint 3-16) has been selected.
REM Remote setpoint When lit, this indicates that a remote setpoint input has been selected. ‘REM’ will also flash when communications is active.
AUTOMAN
Auto/Manual button
When pressed, this toggles between automatic and manual mode: • If the controller is in automatic mode the AUTO
light will be lit. • If the controller is in manual mode, the MAN
light will be lit. The Auto/Manual button can be disabled in configuration level.
RUN
HOLD
Run/Hold button
• Press once to start a program (RUN light on.)
• Press again to hold a program (HOLD light on)
• Press again to cancel hold and continue running (HOLD light off and RUN light ON)
• Press and hold in for two seconds to reset a program (RUN and HOLD lights off)
The RUN light will flash at the end of a program. The HOLD light will flash during holdback or when
a PDS retransmission output is open circuit.
Page button Press to select a new list of parameters.
Scroll button Press to select a new parameter in a list.
Down button Press to decrease a value in the lower readout.
Up button Press to increase a value in lower readout.
Figure 2-3 Controller buttons and indicators
Operation Installation and Operation Handbook
2-4 2408 and 2404 Controller
BASIC OPERATION
Switch on the power to the controller. It runs through a self-test sequence for about three seconds and then shows the measured temperature, or process value, in the upper readout and the target value, called the setpoint, in the lower readout. This is called the Home display.
2404
OP1 OP2
SP2 REM
AUTOMAN
RUNHOLD
Figure 2-4 Home display
You can adjust the setpoint by pressing the or buttons. Two seconds after releasing either button, the display blinks to show that the controller has accepted the new value. OP1 will light whenever output 1 is ON. This is normally the heating output when used as a temperature controller. OP2 will light whenever output 2 is ON. This is normally the cooling output when used as a temperature controller.
Note: You can get back to this display at any time by pressing and together. Alternatively, you will always be returned to this display if no button is pressed for 45 seconds, or whenever the power is turned on.
Alarms
If the controller detects an alarm condition, it flashes an alarm message in the Home display. For a list of all the alarm messages, their meaning and what to do about them, see Alarms at the end of this chapter.
Measured temperature or process value
Setpoint
SP2 REM
OP2 OP1 2404
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-5
OPERATING MODES
The controller has two basic modes of operation:
• Automatic mode in which the output is automatically adjusted to maintain the temperature or process value at the setpoint.
• Manual mode in which you can adjust the output independently of the setpoint.
You toggle between the modes by pressing the AUTO/MAN button. The displays which appear in each of these modes are explained in this chapter.
Two other modes are also available:
• Remote Setpoint mode, in which the setpoint is generated from an external source. In this mode, the REM light will be on.
• Programmer mode which is explained in Chapter 5, Programmer Operation.
Operation Installation and Operation Handbook
2-6 2408 and 2404 Controller
AUTOMATIC MODE
You will normally work with the controller in automatic mode. If the MAN light is on, press the AUTO/MAN button to select automatic mode. The AUTO light comes on. Power on
x 2
The Home display
Check that the AUTO light is on. The upper readout shows the measured temperature. The lower readout shows the setpoint. To adjust the setpoint up or down, press or . (Note: If Setpoint Rate Limit has been enabled, then the lower readout will show the active setpoint. If or is pressed, it will change to show and allow adjustment of, the target setpoint.)
Press once.
Display units A single press of will flash the display units for 0.5 seconds, after which you will be returned to the Home display. Flashing of the display units may have been disabled in configuration in which case a single press will take you straight to the display shown below.
Press twice % Output power demand
The % output power demand is displayed in the lower readout. This is a read-only value. You cannot adjust it. Press and together to return to the Home display.
Press
Pressing from the Output Power display may access further parameters. These may be in this scroll list if the ‘Promote’ feature has been used (see Chapter 3, Edit Level). When you reach the end of this scroll list, pressing will return you to the Home display.
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-7
MANUAL MODE
If the AUTO light is on, press the AUTO/MAN button to select manual mode. The MAN light comes on. Power on
x 2
The Home display
Check that the MAN light is on. The upper readout shows the measured temperature, or process value. The lower readout shows the % output. To adjust the output, press or . (Note: If Output Rate Limit has been enabled, then the lower readout will show the working output. If or is pressed, it will change to show and allow adjustment of, the target output.)
Press once.
Display units A single press of flashes the display units for 0.5 seconds, after which you are returned to the Home display. Flashing of the display units may have been disabled in configuration, in which case a single press will take you straight to the display shown below.
Press twice.
Setpoint
To adjust the setpoint value, press or .
Press .
Pressing from the Output Power display may access further parameters. These may be in this scroll list if the ‘Promote’ feature has been used (see Chapter 3, Edit Level). When you reach the end of this scroll list, pressing will return you to the Home display.
Operation Installation and Operation Handbook
2-8 2408 and 2404 Controller
PARAMETERS AND HOW TO ACCESS THEM Parameters are settings, within the controller, that determine how the controller will operate. For example, alarm setpoints are parameters that set the points at which alarms will occur. For ease of access, the parameters are arranged in lists as shown in the navigation diagram on Pages 2-10 and 2-11. The lists are: Home list Run list Programming list Alarm list Autotune list
PID list Motor list Setpoint list Input list Output list
Communications list Information list Access list.
Each list has a ‘List Header’ display.
List header displays
Figure 2-5 Typical list header display
A list header can be recognised by the fact that it always shows ‘LiSt’ in the lower readout. The upper readout is the name of the list. In the above example, ‘AL’ indicates that it is the Alarm list header. List header displays are read-only.
To step through the list headers, press . Depending upon how your controller has been configured, a single press may momentarily flash the display units. If this is the case, a double press will be necessary to take you to the first list header. Keep pressing to step through the list headers, eventually returning you to the Home display.
To step through the parameters within a particular list, press . When you reach the end of the list, you will return to the list header. From within a list you can return to the current list header at any time can by pressing . To step to the next list header, press once again.
List name
Always displays ‘LiSt’
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-9
Parameter names
In the navigation diagram, each box shows the display for a selected parameter. The Operator parameter tables, later in this chapter, list all the parameter names and their meanings. The navigation diagram shows all the parameters that can, potentially, be present in the controller. In practice, a limited number of them appear, as a result of the particular configuration. The shaded boxes in the diagram indicate parameters that are hidden in normal operation. To view all the available parameters, you must select Full access level. For more information about this, see Chapter 3, Access Levels.
Parameter displays
Figure 2-6 Typical parameter display
Parameter displays show the controller’s current settings. The layout of parameter displays is always the same: the upper readout shows the parameter name and the lower readout its value. In the above example, the parameter name is 1FSL (indicating Alarm 1, full scale low), and the parameter value is 10.0.
To change the value of a parameter
First, select the required parameter. To change the value, press either or . During adjustment, single presses change the value by one digit. Keeping the button pressed speeds up the rate of change. Two seconds after releasing either button, the display blinks to show that the controller has accepted the new value.
Parameter name
Parameter value
Operation Installation and Operation Handbook
2-10 2408 and 2404 Controller
NAVIGATION DIAGRAM (PART A) (The parameters that appear depend upon how the controller has been configured)
Figure 2-7a Navigation diagram (Part A)
Home List
Programmer List(1)
Alarm List
Autotune List
Motor List(3)
Atun LiSt
ProG LiSt
Hb OFF
PrG.n 1
Hb V 20
dwL.U Hour
rmP.U Hour
CYC.n 1
tYPE rmP.r
SEG.n 1
tGt 200
SEG.n 2
rAtE 5.0
tYPE dwEl
Pid LiSt
PID List
PrG.t 35.0
out.n OFF
20.0 20.0
OP 100.0
m-A Auto
AmPS 5
rAtE 5.0
run LiSt
dur 1.0
StAt run
PrG 1
PSP 20
CYC 1
SEG 1
SEG.t 1.0
StyP rmP.r
Run List(1)
tGt 200
tYPE End
SEG.n 3
AL LiSt
2—2 0
1—2 100
3—2 5
HY 2 1
HY 1 1
HY 3 1
Lb t OFF
HY 4 1
diAG no
4—2 5
drA OFF
tunE OFF
drA.t 0.8
Adc mAn
FF.tr 0
FF.dv 100.0
rEL.2 1.00
FF.Pb 0.0
Lcb2 Auto
Hcb2 Auto
mtr LiSt
tm 30.0
In.t OFF
bAc.t OFF
mp.t Auto
V.br dwn
20.0 oC
FASt no
tYPE dwEl
rES.2 0.0
Pb 5
SEt Pid.1
ti 300
rES 0.0
td 60.0
Hcb Auto
rEL.C 1.00
Lcb Auto
Pb2 10
td.2 50.0
ti.2 300
G.SP 500
SYnc no
SEG.d YES
C.id 1
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-11
NAVIGATION DIAGRAM (PART B)
Figure 2-7b Navigation diagram (Part B)
SP LiSt
sp3 to sp16
if configured
Setpoint List
Notes: 1. These lists are present only in controllers with the programming
feature. 2. The last three characters depend upon the type of alarm
configured. 3. This list is only present in motorised valve controllers. 4. Absolute setpoint limits are set in configuration, see Chapter 6.
The shaded boxes are normally hidden in Operator level. To see all the available parameters you must select Full level. See Chapter 3, Access Levels.
L-r Loc
SSEL SP 1
SP 1 20.0
SP 2 0.0
rm.SP 0.0
rmt.t 0.0
SP L4 0.0
rat Off
SP H4 100.0
Loc.t 0
For additional parameters — see tables
iP LiSt
oP LiSt
cmS LiSt
inFo LiSt
ACCS LiSt
Goto OPEr
codEPASS
Input List
Output List
Comms List
Information List
Access List
OP.Lo 0.0
OPrr OFF
CYC.H20.0
ont.HAuto
Addr 1
LoG.H 100.0
LoG.L 0.0
LoG.A 50.0
LoG.t 1000
rES. no
LoG. 0.0
mCt 0
hYS.H 1.0
hYS.C 1.0
HC.db 0.0
P OP19
I OP10
d OP1.
FF.OP 0
FiLtOFF
FLt.2OFF
CAL FACt
CYC.C 5.0
ont.C Auto
di SPStd
w.OP 0.0
FOP 0.0
Sb.OP 100.0
The parameters that follow depend upon the controller configuration.
Refer to the parameter table.
They cover: user calibration & the 2nd PV input fiunctions.
OP.Hi100.0
Operation Installation and Operation Handbook
2-12 2408 and 2404 Controller
PARAMETER TABLES Name Description
Home list Home Measured value and Setpoint OPOPOPOP % Output level
SPSPSPSP Target setpoint (if in Manual mode )
mmmm—-AAAA Auto-man select
AmPSAmPSAmPSAmPS Heater current (With PDSIO mode 2)
C.idC.idC.idC.id Customer defined identification number
+ Extra parameters, if the ‘Promote’ feature has been used (see Chapter 3, Edit Level).
runrunrunrun Program run list − Present only in setpoint programming controllers
PrGPrGPrGPrG Active program number (Only on 4, or 20, program versions) StAtStAtStAtStAt Program status (OFF, run, hoLd, HbAc, End)
PSPPSPPSPPSP Programmer setpoint
CYCCYCCYCCYC Number of cycles remaining in the program
SEGSEGSEGSEG Active segment number
StyPStyPStyPStyP Active segment type
SEG.tSEG.tSEG.tSEG.t Segment time remaining in the segment units
tGttGttGttGt Target setpoint
rAtErAtErAtErAtE Ramp rate (if a rate segment)
PrG.tPrG.tPrG.tPrG.t Program time remaining in hours
FAStFAStFAStFASt Fast run through program (no / YES)
out.nout.nout.nout.n Event output states (OFF / on) (not 8-segment programmer)
SYncSYncSYncSYnc Segment synchronisation (no / YES) (not 8-segment programmer)
SEG.dSEG.dSEG.dSEG.d Flash active segment type in the lower readout of the home display (no / YES)
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-13
Name Description
ProGProGProGProG Program edit list − Present only in setpoint programming controller. For a fuller explanation of these parameters refer to Chapter 5
PrG.nPrG.nPrG.nPrG.n Select program number (Only on 4, or 20, program versions)
HbHbHbHb Holdback type for the program as a whole (if configured)(OFF, Lo, Hi, or bAnd)
HbHbHbHb VVVV Holdback value (in display units)
rmP.UrmP.UrmP.UrmP.U Ramp units (SEc, min, or Hour) [for both rmP.rrmP.rrmP.rrmP.r and rmP.trmP.trmP.trmP.t type segments] dwL.UdwL.UdwL.UdwL.U Dwell units (SEc, min, or Hour) CYC.nCYC.nCYC.nCYC.n Number of program cycles (1 to 999, or ‘cont’) SEG.nSEG.nSEG.nSEG.n Segment number
tYPEtYPEtYPEtYPE Segment type:(EndEndEndEnd) (rmP.rrmP.rrmP.rrmP.r=ramp rate) (rmPrmPrmPrmP.t.t.t.t=ramp time) (dweldweldweldwel) (StEPStEPStEPStEP) (cALLcALLcALLcALL) The following parameters depend on the tYPE selected, as shown below.
End rmP.r rmP.t dwEl StEP cALL
HbHbHbHb Holdback type: OFF, Lo, Hi, or bAnd tGttGttGttGt Target setpoint for a ‘rmP’ or ‘StEP’ segment rAtErAtErAtErAtE Ramp rate for a ‘rmP.r’ segment durdurdurdur ‘dwEl’ time / Time to target for a ‘rmP.t’ segment PrG.nPrG.nPrG.nPrG.n cALLed ProGram number cYc.ncYc.ncYc.ncYc.n No. of cycles of cALLed program outnoutnoutnoutn Event output: OFF/on (not 8-segment programmer) SYncSYncSYncSYnc Segment synchronisation: no/YES (not 8-seg progr)
End.tEnd.tEnd.tEnd.t End of prog − dwEl, RSEt, S OP PwrPwrPwrPwr Power level in end segment
Operation Installation and Operation Handbook
2-14 2408 and 2404 Controller
Name Description
ALALALAL Alarm list 1111 —- —- —- Alarm 1 setpoint value
2222 —- —- —- Alarm 2 setpoint value
3333 —- —- —- Alarm 3 setpoint value
4444 —- —- —- Alarm 4 setpoint value
In place of dashes, the last three characters indicate the alarm type. See alarm types table:
HYHYHYHY 1111 Alarm 1 Hysteresis (display units)
HYHYHYHY 2222 Alarm 2 Hysteresis (display units)
HYHYHYHY 3333 Alarm 3 Hysteresis (display units)
HYHYHYHY 4444 Alarm 4 Hysteresis (display units)
LbLbLbLb tttt Loop Break Time in minutes
diAGdiAGdiAGdiAG Enable Diagnostic alarms ‘no’ / ‘YES’
Alarm types table
—-FSLFSLFSLFSL PV Full scale low alarm
—-FSHFSHFSHFSH PV Full scale high alarm
—-dEvdEvdEvdEv PV Deviation band alarm
—-dHidHidHidHi PV Deviation high alarm
—-dLodLodLodLo PV Deviation low alarm
—-LCrLCrLCrLCr Load Current low alarm
—-HCrHCrHCrHCr Load Current high alarm
—-FL2FL2FL2FL2 Input 2 Full Scale low alarm
—-FH2FH2FH2FH2 Input 2 Full Scale high alarm
—-LOPLOPLOPLOP Working Output low alarm
—-HOPHOPHOPHOP Working Output high alarm
—-LSPLSPLSPLSP Working Setpoint low alarm
—-HSPHSPHSPHSP Working Setpoint high alarm
4rAt4rAt4rAt4rAt Rate of change alarm (AL 4 only)
AtunAtunAtunAtun Autotune list
tunEtunEtunEtunE One-shot autotune enable
drAdrAdrAdrA Adaptive tune enable
drA.tdrA.tdrA.tdrA.t Adaptive tune trigger level in display units. Range = 1 to 9999
AdcAdcAdcAdc Automatic Droop Compensation (PD control only)
Name Description
PidPidPidPid PID list G.SPG.SPG.SPG.SP If Gain Scheduling has been
enabled (see Chapter 4), this parameter sets the PV below which ‘Pid.1’ is active and above which ‘Pid.2’ is active.
SEtSEtSEtSEt ‘Pid.1’ or ‘Pid.2’ selected
PbPbPbPb Proportional Band (SEt 1) (in display units)
titititi Integral Time in secs (SEt 1)
tdtdtdtd Derivative Time in secs (SEt 1)
rESrESrESrES Manual Reset (%) (SEt 1)
HcbHcbHcbHcb Cutback High (SEt 1)
LcbLcbLcbLcb Cutback Low (SEt 1)
rEL.CrEL.CrEL.CrEL.C Relative Cool Gain (SEt 1)
Pb2Pb2Pb2Pb2 Proportional Band (SEt 2) ti2ti2ti2ti2 Integral Time in secs (SEt 2) td2td2td2td2 Derivative Time in secs (SEt 2) rES.2rES.2rES.2rES.2 Manual Reset (%) (SEt 2) Hcb2Hcb2Hcb2Hcb2 Cutback High (SEt 2) Lcb2Lcb2Lcb2Lcb2 Cutback Low (SEt 2) rEL.2rEL.2rEL.2rEL.2 Relative Cool Gain (SEt 2) The following three parameters are used for cascade control. If this facility is not being used, then they can be ignored. FF.PbFF.PbFF.PbFF.Pb SP, or PV, feedforward propband FF.trFF.trFF.trFF.tr Feedforward trim % FF.dvFF.dvFF.dvFF.dv PID feedforward limits ± %
mtrmtrmtrmtr Motor list — see Table 4-3
tm Valve travel time in seconds
In.t Valve inertia time in secs
bAc.t Valve backlash time in secs
mp.t Minimum ON time of output pulse
U.br Valve sensor break strategy
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-15
Name Description
SPSPSPSP Setpoint list
SSEL Select SP 1 to SP16, depending on configuration
L-r Local (Loc) or remote (rmt) setpoint select
SP 1 Setpoint one value
SP 2 Setpoint two value
rm.SP Remote setpoint value
rmt.t Remote setpoint trim
rat Ratio setpoint
Loc.t Local setpoint trim
SP L Setpoint 1 low limit
SP H Setpoint 1 high limit
SP2.L Setpoint 2 low limit
SP2.H Setpoint 2 high limit
SPrr Setpoint Rate Limit
Hb.ty Holdback Type for setpoint rate limit (OFF, Lo, Hi, or bAnd)
Hb Holdback Value for setpoint rate limit in display units. (Hb.ty ≠ Off)
iPiPiPiP Input list
FiLt IP1 filter time constant (0.0 — 999.9 seconds).
FLt.2 IP2 filter time constant (0.0 — 999.9 seconds).
Hi.IP
Lo.Ip
Transition of control between ip.1 and ip.2. (if configured) The transition region is set by the values of ‘Lo.Ip’ and ‘Hi.Ip’. PV = ip.1 below ‘Lo.Ip’
PV = ip.2 above ‘Hi.Ip’
F.1
F.2
Derived function, (if configured) PV = (f.1 x iP1) + (f.2 x iP2). ‘F.1’ and ‘F.2’ are scalars with the range -9.99 to 10.00
PV.ip Selects ‘ip.1’ or ‘ip.2’
Continued in next column
Name Description
iPiPiPiP Input list — continued The next 3 parameters appear if User Calibration has been enabled. (Refer to Chapter 7.) By default they are hidden when in Operator level. To prevent unauthorised adjustment, we recommend that they are only made available in FuLL access level.
CAL ‘FACt’ — reinstates the factory calibration and disables User calibration. Next 2 parameters will not appear.
‘USEr’ — reinstates any previously set User calibration. All parameters below now appear.
CAL.s Selected calibration point − ‘nonE’, ’iP1.L’, ‘ip1.H’, ’iP2.L’, ‘ip2.H’
AdJ * User calibration adjust, if CAL.s = ’iP1.L’, ‘ip1.H’, ’iP2.L’, ‘ip2.H’
OFS.1 IP1 calibration offset
OFS.2 IP2 calibration offset
mV.1 IP1 measured value (at terminals)
mV.2 IP2 measured value (at terminals), if DC input in Module 3 position
CJC.1 IP1 cold junction temp. reading
CJC.2 IP2 cold junction temp. reading
Li.1 IP1 linearised value
Li.2 IP2 linearised value
PV.SL Shows the currently selected PV input — ‘ip.1’ or ‘ip.2’
* Do not make adjustments using the AdJ parameter unless you wish to change the controller calibration.
Operation Installation and Operation Handbook
2-16 2408 and 2404 Controller
Name Description
oPoPoPoP Output list Does not appear if Motorised Valve control configured. OP.Lo Low power limit (%)
OP.Hi High power limit (%)
OPrr Output Rate Limit (% per sec)
FOP Forced output level (%)
CYC.H Heat cycle time (0.2S to 999.9S)
hYS.H Heat hysteresis (display units)
ont.H Heat output min. on-time (secs) Auto (0.05S), or 0.1 — 999.9S
CYC.C Cool cycle time (0.2S to 999.9S)
hYS.C Cool hysteresis (display units)
ont.C Cool output min. on-time (secs) Auto (0.05S), or 0.1 — 999.9S
HC.db Heat/cool deadband (display units)
Sb.OP Sensor Break Output Power (%)
cmScmScmScmS Comms list
Addr Communications Address
cmScmScmScmS DeviceNet (additional
parameters) Nw.St Indicates network status run Network connected and
operational rdy Network connected but not
operational oFF.L Network not connected
inFoinFoinFoinFo Information list
diSP Configure lower readout of Home display to show: VPoS Valve position Std Standard — display setpoint AmPS Load current in amps OP Output Stat Program status PrG.t Program time remaining in hours Li 2 Process value 2 rAt Ratio setpoint PrG Selected program number rSP Remote setpoint
LoG.L PV minimum
LoG.H PV maximum
LoG.A PV mean value
Log.t Time PV above Threshold level
Log.v PV Threshold for Timer Log Continued in next column
Name Description
inFoinFoinFoinFo Information list — continued
rES.L Logging Reset — ‘YES/no’ The following set of parameters is for diagnostic purposes. w.OP Working output
FF.OP Feedforward component of output
VO PID output to motorised valve
ACCSACCSACCSACCS Access List
codE Access password
Goto Goto level — OPEr, FuLL, Edit or conF
ConF Configuration password
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-17
ALARMS
Alarm annunciation Alarms are flashed as messages in the Home display. A new alarm is displayed as a double flash followed by a pause, old (acknowledged) alarms as a single flash followed by a pause. If there is more than one alarm condition, the display cycles through all the relevant alarm messages. Table 2-1 and Table 2-2 list all of the possible alarm messages and their meanings.
Alarm acknowledgement and resetting Pressing both and at the same time will acknowledge any new alarms and reset any latched alarms.
Alarm modes Alarms will have been set up to operate in one of several modes, either: • Non-latching, which means that the alarm will reset automatically when the Process
Value is no longer in the alarm condition. • Latching, which means that the alarm message will continue to flash even if the alarm
condition no longer exists and will only clear when reset. • Blocking, which means that the alarm will only become active after it has first entered a
safe state on power-up.
Alarm types There are two types of alarm: Process alarms and Diagnostic alarms.
Process alarms These warn that there is a problem with the process which the controller is trying to control.
Alarm Display What it means
_FSL* PV Full Scale Low alarm
_FSH* PV Full Scale High alarm
_dEv* PV Deviation Band alarm
_dHi* PV Deviation High alarm
_dLo* PV Deviation Low alarm
_LCr* Load Current Low alarm
_HCr* Load Current High alarm
* In place of the dash, the first character will indicate the alarm number. Table 2-1 Process alarms
Alarm Display What it means
_FL2* Input 2 Full Scale Low alarm
_FH2* Input 2 Full Scale High alarm
_LOP* Working Output Low alarm
_HOP* Working Output High alarm
_LSP* Working Setpoint Low alarm
_HSP* Working Setpoint High alarm
4rAt PV Rate of change alarm Always assigned to Alarm 4
Operation Installation and Operation Handbook
2-18 2408 and 2404 Controller
Diagnostic alarms
These indicate that a fault exists in either the controller or the connected devices.
Display shows
What it means What to do about it
EE.ErEE.ErEE.ErEE.Er Electrically Erasable Memory Error: The value of an operator, or configuration, parameter has been corrupted.
This fault will automatically take you into Configuration level. Check all of the configuration parameters before returning to Operator level. Once in Operator level, check all of the operator parameters before resuming normal operation. If the fault persists, or occurs frequently, contact your supplier
S.brS.brS.brS.br Sensor Break: Input sensor is unreliable or the input signal is out of range.
Check that the sensor is correctly connected.
L.brL.brL.brL.br Loop Break The feedback loop is open circuit.
Check that the heating and cooling circuits are working properly.
Ld.FLd.FLd.FLd.F Load failure Indication that there is a fault in the heating circuit or the solid state relay.
This is an alarm generated by feedback from a TE10S solid state relay (SSR) operating in PDSIO mode 1 — see Chapter 1, Electrical Installation. It indicates either an open or short circuit SSR, blown fuse, missing supply or open circuit heater.
SSr.FSSr.FSSr.FSSr.F Solid state relay failure Indication that there is a fault in the solid state relay.
This is an alarm generated by feedback from a TE10S solid state relay (SSR) operating in PDSIO mode 2 — see Chapter 1, Electrical Installation. It indicates either an open or short circuit condition in the SSR.
Htr.FHtr.FHtr.FHtr.F Heater failure Indication that there is a fault in heating circuit.
This is an alarm generated by feedback from a TE10S solid state relay (SSR) operating in PDSIO mode 2 — see Chapter 1, Electrical Installation. It indicates either a blown fuse, missing supply, or open circuit heater.
Ct.OPCt.OPCt.OPCt.OP Current Transformer Open Circuit
Indicates that the PDS input is open circuit.
Mode 5 only
Ct.ShCt.ShCt.ShCt.Sh Current Transformer Short Circuit
Indicates that the PDS input is short circuit
Mode 5 only
Hw.ErHw.ErHw.ErHw.Er Hardware error Indication that a module is of the wrong type, missing, or faulty.
Check that the correct modules are fitted.
Operation Installation and Operation Handbook
2408 and 2404 Controller 2-19
no.iono.iono.iono.io No I/O None of the expected I/O modules is fitted.
This error message normally occurs when pre-configuring a controller without installing any of the required I/O modules.
rmt.Frmt.Frmt.Frmt.F Remote input failure. Either the PDSIO input, or the remote DC input, is open or short circuit
Check for open, or short circuit wiring on the PDSIO, or remote DC, input.
LLLLLLLLLLLLLLLL Out of range low reading Check the value of the input.
HHHHHHHHHHHHHHHH Out of range high reading Check the value of the input.
Err1Err1Err1Err1 Error 1: ROM self-test fail Return the controller for repair.
Err2Err2Err2Err2 Error 2: RAM self-test fail Return the controller for repair.
Err3Err3Err3Err3 Error 3: Watchdog fail Return the controller for repair.
Err4Err4Err4Err4 Error 4: Keyboard failure Stuck button, or a button was pressed during power up.
Switch the power off and then on, without touching any of the controller buttons.
Err5Err5Err5Err5 Error 5: Faulty internal communications.
Check printed circuit board interconnections. If the fault cannot be cleared, return the controller for repair.
Err6Err6Err6Err6 Digital filter chip faulty or loose board inside controller
Return the controller for repair.
Err7Err7Err7Err7 PV id failure/PSU failure Return the controller for repair.
Err8Err8Err8Err8 Module 1 id error Faulty or loose module or may be isolation problem
Err9Err9Err9Err9 Module 2 id error Faulty or loose module or may be isolation problem
ErrAErrAErrAErrA Module 3 id error Faulty or loose module or may be isolation problem
DCFDCFDCFDCF DC output fail Return the controller for repair
Tu.ErTu.ErTu.ErTu.Er Tune error – shown If any one stage of the auto-tuning process exceeds two hours
Check response time of process: check that the sensor has not failed: check that the loop is not broken. Acknowledge by pressing ‘page’ key and ‘scroll’ key together
P.brP.brP.brP.br Potentiometer break Check that the feedback potentiometer is correctly connected or the pot is not open circuit
Table 2-2 Diagnostic alarms
Operation Installation and Operation Handbook
2-20 2408 and 2404 Controller
Installation and Operation Handbook Access Levels
2408 and 2404 Controller 3-1
Chapter 3 ACCESS LEVELS
This chapter describes the different levels of access to the operating parameters within the controller. There are three topics:
• THE DIFFERENT ACCESS LEVELS
• SELECTING AN ACCESS LEVEL
• EDIT LEVEL THE DIFFERENT ACCESS LEVELS
There are four access levels:
• Operator level, which you will normally use to operate the controller.
• Full level, which is used to commission the controller.
• Edit level, which is used to set up the parameters that you want an operator to be able to see and adjust when in Operator level.
• Configuration level, which is used to set up the fundamental characteristics of the controller.
Access level
Display shows
What you can do Password Protection
Operator OPEr In this level, operators can view and adjust the value of parameters defined in Edit level (see below).
No
Full FuLL In this level, all the parameters relevant to a particular configuration are visible. All alterable parameters may be adjusted.
Yes
Edit Edit In this level, you can determine which parameters an operator is able to view and adjust in Operator level. You can hide, or reveal, complete lists, individual parameters within each list and you can make parameters read-only or alterable. (See Edit level at the end of this chapter).
Yes
Configuration conF This special level allows access to set up the fundamental characteristics of the controller.
Yes
Figure 3-1 Access levels
Access Levels Installation and Operation Handbook
3-2 2408 and 2404 Controller
SELECTING AN ACCESS LEVEL
Access to Full, Edit or Configuration levels is protected by a password to prevent unauthorised access. If you need to change the password, see Chapter 6, Configuration.
Access list header
Press until you reach the access list header ‘ACCS’.
Press
Password entry
The password is entered from the ‘codE’ display. Enter the password using or . Once the correct password has been entered, there is a two second delay after which the lower readout will change to show ‘PASS’ indicating that access is now unlocked. The pass number is set to ‘1’ when the controller is shipped from the factory. Note; A special case exists if the password has been set to ‘0’. In this case access will be permanently unlocked and the lower readout will always show ‘PASS’.
Press to proceed to the ‘Goto’ page.
(If an incorrect password has been entered and the controller is still ‘locked’ then pressing returns you to the ‘ACCS’ list header.)
Access to Read-only Configuration
From this display, pressing and together will take you into Read-Only Configuration without entering a password. This will allow you to view all of the configuration parameters, but not adjust them. If no button is pressed for ten seconds, you will be returned to the Home display. Alternatively, pressing and together takes you immediately back to the Home display.
Installation and Operation Handbook Access Levels
2408 and 2404 Controller 3-3
Level selection
The ‘Goto’ display allows you to select the required access level. Use and to select from the following display codes: OPEr: Operator level FuLL: Full level Edit: Edit level conF: Configuration level
Press
If you selected either ‘OPEr’, ‘FuLL’ or ‘Edit’ level you will be returned to the ‘ACCS’ list header in the level that you chose. If you selected ‘conF’, you will get a display showing ‘ConF’ in the upper readout (see below).
Configuration password
When the ‘ConF’ display appears, you must enter the Configuration password in order to gain access to this level. Do this by repeating the password entry procedure described in the previous section. The configuration password is set to ‘2’ when the controller is shipped from the factory. If you need to change the configuration password, see Chapter 6, Configuration.
Press
Configuration level
The first display of configuration is shown. See Chapter 6, Configuration, for details of the configuration parameters. For instructions on leaving configuration level, see Chapter 6, Configuration.
Returning to Operator Level
To return to operator level from either ‘FuLL’ or ‘Edit’ level, repeat entry of the password and select ‘OPEr’ on the ‘Goto’ display. In ‘Edit’ level, the controller will automatically return to operator level if no button is pressed for 45 seconds.
Alternative path if ‘conF’ selected
Access Levels Installation and Operation Handbook
3-4 2408 and 2404 Controller
EDIT LEVEL
Edit level is used to set which parameters you can view and adjust in Operator level. It also gives access to the ‘Promote’ feature, which allows you to select and add (‘Promote’) up to twelve parameters into the Home display list, thereby giving simple access to commonly used parameters.
Setting operator access to a parameter
First you must select Edit level, as shown on the previous page. Once in Edit level, you select a list, or a parameter within a list, in the same way as you would in Operator, or Full, level − that is to say, you move from list header to list header by pressing , and from parameter to parameter within each list using . However, in Edit level what is displayed is not the value of a selected parameter, but a code representing that parameter’s availability in Operator level. When you have selected the required parameter, use and buttons to set its availability in Operator level.
There are four codes: ALtrALtrALtrALtr Makes a parameter alterable in Operator level. PrOPrOPrOPrO Promotes a parameter into the Home display list. rEAdrEAdrEAdrEAd Makes a parameter, or list header, read-only (it can be viewed but not altered). HIdEHIdEHIdEHIdE Hides a parameter, or list header. For example:
Hiding or revealing a complete list
To hide a complete list of parameters, all you have to do is hide the list header. If a list header is selected, only two selections are available: rEAd and HIdE. (It is not possible to hide the ‘ACCS’ list, which always displays the code: ‘LiSt’.)
Promoting a parameter
Scroll through the lists to the required parameter and choose the ‘PrO’ code. The parameter is then automatically added (promoted) into the Home display list. (The parameter will also be accessible, as normal, from the standard lists.) A maximum of twelve parameters can be promoted. Promoted parameters are automatically ‘alterable’.
Please note, in the ‘PrOG List’, the parameters from segment number (SEG.n) onwards cannot be promoted.
The parameter selected is Alarm 2, Full Scale Low
It will be alterable in Operator level
Installation and Operation Handbook Tuning
2408 and 2404 Controller 4-1
Chapter 4 TUNING Before tuning, please read Chapter 2, Operation, to learn how to select and change a parameter.
This chapter has five topics: • WHAT IS TUNING?
• AUTOMATIC TUNING
• MANUAL TUNING
• COMMISSIONING OF MOTORISED VALVE CONTROLLERS
• GAIN SCHEDULING WHAT IS TUNING?
In tuning, you match the characteristics of the controller to those of the process being controlled in order to obtain good control. Good control means: • Stable, ‘straight-line’ control of the temperature at setpoint without fluctuation • No overshoot, or undershoot, of the temperature setpoint • Quick response to deviations from the setpoint caused by external disturbances, thereby
rapidly restoring the temperature to the setpoint value.
Tuning involves calculating and setting the value of the parameters listed in Table 4-1. These parameters appear in the ‘Pid’ list.
Parameter
Code
Meaning or Function
Proportional band
Pb The bandwidth, in display units, over which the output power is proportioned between minimum and maximum.
Integral time ti Determines the time taken by the controller to remove steady-state error signals.
Derivative time td Determines how strongly the controller will react to the rate-of-change of the measured value.
High Cutback Hcb The number of display units, above setpoint, at which the controller will increase the output power, in order to prevent undershoot on cool down.
Low cutback Lcb The number of display units, below setpoint, at which the controller will cutback the output power, in order to prevent overshoot on heat up.
Relative cool gain
rEL Only present if cooling has been configured and a module is fitted. Sets the cooling proportional band, which equals the Pb value divided by the rEL value.
Table 4-1 Tuning parameters
Tuning Installation and Operation Handbook
4-2 2408 and 2404 Controller
AUTOMATIC TUNING
Two automatic tuning methods are provided in the 2408 and 2404: • A one-shot tuner, which automatically sets up the initial values of the parameters listed
in Table 4-1 on the previous page. • Adaptive tuning, which continuously monitors the error from setpoint and modifies the
PID values, if necessary.
One-shot Tuning
The ‘one-shot’ tuner works by switching the output on and off to induce an oscillation in the measured value. From the amplitude and period of the oscillation, it calculates the tuning parameter values. If the process cannot tolerate full heating or cooling being applied during tuning, then the level of heating or cooling can be restricted by setting the heating and cooling power limits in the ‘oP’ list. However, the measured value must oscillate to some degree for the tuner to be able to calculate values. A One-shot Tune can be performed at any time, but normally it is performed only once during the initial commissioning of the process. However, if the process under control subsequently becomes unstable (because its characteristics have changed), you can re-tune again for the new conditions. It is best to start tuning with the process at ambient temperature. This allows the tuner to calculate more accurately the low cutback and high cutback values which restrict the amount of overshoot, or undershoot.
How to tune
1. Set the setpoint to the value at which you will normally operate the process. 2. In the ‘Atun’ list, select ‘tunE’ and set it to ‘on’. 3. Press the Page and Scroll buttons together to return to the Home display. The display will
flash ‘tunE’ to indicate that tuning is in progress. 4. The controller induces an oscillation in the temperature by first turning the heating on,
and then off. The first cycle is not complete until the measured value has reached the required setpoint.
5. After two cycles of oscillation the tuning is completed and the tuner switches itself off. 6. The controller then calculates the tuning parameters listed in Table 4-1 and resumes
normal control action. If you want ‘Proportional only’, ‘PD’, or ‘PI’ control, you should set the ‘ti’ or ‘td’ parameters to OFF before commencing the tuning cycle. The tuner will leave them off and will not calculate a value for them.
Installation and Operation Handbook Tuning
2408 and 2404 Controller 4-3
Typical automatic tuning cycle
Calculation of the cutback values
Low cutback and High cutback are values that restrict the amount of overshoot, or undershoot, that occurs during large step changes in temperature (for example, under start-up conditions). If either low cutback, or high cutback, is set to ‘Auto’ the values are fixed at three times the proportional band, and are not changed during automatic tuning.
Adaptive tune
Adaptive tuning is a background algorithm, which continuously monitors the error from setpoint and analyses the control response during process disturbances. If the algorithm recognises an oscillatory, or under-damped, response it recalculates the Pb, ti and td values. Adaptive tune is triggered whenever the error from setpoint exceeds a trigger level. This trigger level is set in the parameter ‘drA.t’, which is found in the Autotune list. The value is in display units. It is automatically set by the controller, but can also be manually re-adjusted. Adaptive tune should be used with: 1. Processes whose characteristics change as a result of changes in the load, or setpoint. 2. Processes that cannot tolerate the oscillation induced by a One-shot tune. Adaptive tune should not be used: 1. Where the process is subjected to regular external disturbances that could mislead the
adaptive tuner. 2. On highly interactive multiloop applications. However, moderately interactive loops,
such as multi-zone extruders, should not give a problem.
Time
Setpoint Temperature
Tuning Installation and Operation Handbook
4-4 2408 and 2404 Controller
MANUAL TUNING
If for any reason automatic tuning gives unsatisfactory results, you can tune the controller manually. There are a number of standard methods for manual tuning. The one described here is the Ziegler-Nichols method. With the process at its normal running temperature: 1. Set the Integral Time ‘ti’ and the Derivative Time ‘td’ to OFF. 2. Set High Cutback and Low Cutback, ‘Hcb’ and ‘Lcb’, to ‘Auto’. 3. Ignore the fact that the temperature may not settle precisely at the setpoint. 4. If the temperature is stable, reduce the proportional band ‘Pb’ so that the temperature just
starts to oscillate. If the temperature is already oscillating, increase the proportional band until it just stops oscillating. Allow enough time between each adjustment for the loop to stabilise. Make a note of the proportional band value ‘B’ and the period of oscillation ‘T’.
5. Set the Pb, ti, td parameter values according to the calculations given in Table 4-2.
Type of control
Proportional
band ‘Pb’
Integral time ‘ti’
Derivative time
‘td’
Proportional only
2xB
OFF
OFF
P + I control
2.2xB
0.8xT
OFF
P + I + D control
1.7xB
0.5xT
0.12xT
Table 4-2 Tuning values
Installation and Operation Handbook Tuning
2408 and 2404 Controller 4-5
Setting the cutback values
The above procedure sets up the parameters for optimum steady state control. If unacceptable levels of overshoot or undershoot occur during start-up, or for large step changes in temperature, then manually set the cutback parameters ‘Lcb’ and ‘Hcb’. Proceed as follows: 1. Set the low and high cutback values to three proportional bandwidths (that is to say, Lcb
= Hcb = 3 x Pb). 2. Note the level of overshoot, or undershoot, that occurs for large temperature changes (see
the diagrams below). In example (a) increase ‘Lcb’ by the overshoot value. In example (b) reduce ‘Lcb’ by the undershoot value. Example (a)
Example (b)
Where the temperature approaches setpoint from above, you can set ‘Hcb’ in a similar manner.
Temperature
Time
Setpoint
Temperature
Undershoot
Setpoint Overshoot
Tuning Installation and Operation Handbook
4-6 2408 and 2404 Controller
Integral action and manual reset
In a full three-term controller (that is, a PID controller), the integral term ‘ti’ automatically removes steady state errors from the setpoint. If the controller is set up to work in two-term mode (that is, PD mode), the integral term will be set to ‘OFF’. Under these conditions the measured value may not settle precisely at setpoint. When the integral term is set to ‘OFF’ the parameter manual reset (code ‘rES’) appears in the ‘Pid LiSt’ in ‘FuLL’ level. This parameter represents the value of the power output that will be delivered when the error is zero. You must set this value manually in order to remove the steady state error.
Automatic droop compensation (Adc)
The steady state error from the setpoint, which occurs when the integral term is set to ‘OFF’ is sometimes referred to as ‘droop’. ‘Adc’ automatically calculates the manual reset value in order to remove this droop. To use this facility, you must first allow the temperature to stabilise. Then, in the autotune parameter list, you must set ‘Adc’ to ‘cALc’. The controller will then calculate a new value for manual reset, and switch ‘Adc’ to ‘mAn’. ‘Adc’ can be repeated as often as you require, but between each adjustment you must allow time for the temperature to stabilise.
Tune Error
If any one stage of the automatic tuning process is not completed within two hours a diagnostic alarm will occur. The display shows tU.Er — Tune Error. This alarm could occur if: 1. The process to be tuned has a very slow response time 2. The sensor has failed or is incorrectly aligned 3. The loop is broken or not responding correctly
Installation and Operation Handbook Tuning
2408 and 2404 Controller 4-7
MOTORISED VALVE CONTROL
The 2408 and 2404 can be configured for motorised valve control as an alternative to the standard PID control algorithm. This algorithm is designed specifically for positioning motorised valves. These are ordered pre-configured as Model numbers:
• 2408/VC and 2404/VC motorised valve controllers
• 2408/VP and 2404/VP motorised valve controllers with a single setpoint programmer
• 2408/V4 and 2404/V4 motorised valve controllers storing four setpoint programs.
• 2408/VM and 2404/VM motorised valve controllers storing twenty setpoint programs. Figure 1-11 in Chapter 1 shows how to connect a motorised valve controller. The control is performed by delivering open, or close, pulses in response to the control demand signal. The motorised valve algorithm can operate in one of three ways: 1. The so-called boundless mode, which does not require a position feedback potentiometer
for control purposes; although one can be connected and used purely to display the valve’s position.
2. Bounded, (or position), control mode, which requires a feedback potentiometer. This is closed-loop control determined by the valve’s position.
The desired control mode is selected in the ‘inst’ list in configuration level.
The following parameter list will appear in the navigation diagram shown in Chapter 2, if your controller is configured for motorised valve control.
Name Description Values
mtrmtrmtrmtr Motor list Min Max Default
tm Valve travel time in seconds. This is the time taken for the valve to travel from its fully closed position to its fully open position.
0.1 240.0 30.0
In.t Valve inertia time in seconds. This is the time taken for the valve to stop moving after the output pulse is switched off.
OFF 20.0 OFF
bAc.t Valve backlash time in seconds. This is the minimum on-time required to reverse the direction of the valve. i.e. the time to overcome the mechanical backlash.
OFF 20.0 OFF
mp.t Output pulse minimum on-time, in seconds. Auto 100.0 Auto
U.br Valve sensor break strategy. rESt, uP, dwn rESt
Table 4-3 Motorised valve parameter list
Tuning Installation and Operation Handbook
4-8 2408 and 2404 Controller
COMMISSIONING THE MOTORISED VALVE CONTROLLER
The commissioning procedure is the same for both bounded and boundless control modes, except in bounded mode you must first calibrate the position feedback potentiometer, as described in the section below. Proceed as follows:
1. Measure the time taken for the valve to be raised from its fully closed to its fully open position and enter this as the value in seconds into the ‘tm’ parameter.
2. Set all the other parameters to the default values shown in Table 4-3.
The controller can then be tuned using any of the automatic, or manual, tuning procedures described earlier in this chapter. As before, the tuning process, either automatic or manual, involves setting the values of the parameters in Table 4-1. The only difference with boundless control is that the derivative term ‘td’, although present, will have no effect.
Adjusting the minimum on-time ‘mp.tmp.tmp.tmp.t’
The default value of 0.2 seconds is satisfactory for most processes. If, however, after tuning the process, the valve activity is excessively high, with constant oscillation between raise and lower pulses, the minimum on-time can be increased. The minimum on-time determines how accurately the valve can be positioned and therefore the control accuracy. The shorter the time, the more precise the control. However, if the time is set too short, process noise will cause an excessively busy valve.
Inertia and backlash settings
The default values are satisfactory for most processes, i.e. ‘OFF’. Inertia is the time taken for the valve to stop after the output pulse is turned off. If this causes a control problem, the inertia time needs to be determined and then entered into the parameter, ‘In.t’. The inertia time is subtracted from the raise and lower output pulse times, so that the valve moves the correct distance for each pulse. Backlash is the output pulse time required to reverse the direction of the valve, i.e. the time taken to overcome the mechanical backlash of the linkages. If the backlash is sufficient to cause a control problem, then the backlash time needs to be determined and then entered into the parameter, ‘bac.t’. The above two values are not part of the automatic tuning procedure and must be entered manually.
CALIBRATING THE POSITION FEEDBACK POTENTIOMETER
Before proceeding with the feedback potentiometer calibration, you should ensure, in configuration level, that module position 2 (2a), or 3 (3a), has its ‘id’ indicating ‘Pot.i’, (meaning Potentiometer Input). Continue to scroll down the module configuration list. ‘func’ should be set to ‘Vpos’, ‘VAL.L’ must be set to ‘0’ and ‘VAL.H’ to ‘100’. Exit from configuration and you are now ready to calibrate the position feedback potentiometer. Proceed as follows. 1. In Operator level, press the AUTO/MAN button to put the controller in Manual mode.
2. Drive the valve to its fully open position using .
3. Press until you get to ‘ip-List’.
4. Press to get to ‘PCAL-OFF’.
Installation and Operation Handbook Tuning
2408 and 2404 Controller 4-9
5. Press or to turn ‘PCAL’ to ‘on’.
6. Press and the upper readout indicates ‘Pot’.
7. Press or to get to ‘Pot-3A.Hi’. (Assuming that the Potentiometer Input Module is in module position 3.)
8. Press to go to ‘GO-no’.
9. Press or to see ‘GO-YES’, which starts the calibration procedure. 10. Calibration is complete when the display returns to ‘GO-no’.
11. Press and together to return directly to the Operator level. 12. The controller should still be in Manual mode.
13. Drive the valve to its fully closed position using .
14. Press until you get to ‘ip-List’.
15. Press to get to ‘PCAL-OFF’.
16. Press or to turn ‘PCAL’ to ‘on’.
17. Press and the upper readout indicates ‘Pot’.
18. Press or to get to ‘Pot-3A.Lo’
19. Press to go to ‘GO-no’.
20. Press or to see ‘GO-YES’, which starts the calibration procedure. 21. Calibration is complete when the display returns to ‘GO-no’.
22. Press and together to return directly to the Operator level. 23. Press the AUTO/MAN button to place the controller in AUTO and the calibration of the
position feedback potentiometer is now complete.
Tuning Installation and Operation Handbook
4-10 2408 and 2404 Controller
GAIN SCHEDULING
Gain scheduling is the automatic transfer of control between one set of PID values and another. In the case of the 2408 and 2404 controllers, this is done at a presettable process value. It is used for the more difficult to control processes which exhibit large changes in their response time or sensitivity at, for example, high and low temperatures, or when heating or cooling.
The 2408 and 2404 has two sets of PID values. You can select the active set from either a digital input, or from a parameter in the PID list, or you can transfer automatically in gain scheduling mode. The transfer is bumpless and will not disturb the process being controlled. To use gain scheduling, follow the steps below:
Step1: Enable in configuration level
Gain scheduling must first be enabled in Configuration level. Goto the Inst Conf list, select the parameter Gsch, and set it to YES.
Step 2: Set the transfer point
Once gain scheduling has been enabled, the parameter G.SP will appear at the top of the Pid list in FuLL access level. This sets the value at which transfer occurs. PID1 will be active when the process value is below this setting and PID2 when the process value is above it. The best point of transfer depends on the characteristics of the process. Set a value between the control regions that exhibit the greatest change.
Step 3: Tuning
You must now set up the two sets of PID values. The values can be manually set, or automatically tuned as described earlier in this chapter. When tuning automatically you must tune twice, once above the switching point G.SP and again below the switching point. When tuning, if the process value is below the transfer point G.SP the calculated values will automatically be inserted into PID1 set and if the process value is above G.SP, the calculated values will automatically be inserted into PID2 set.
GSchYES
G.Sp350
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-1
Chapter 5 PROGRAMMER OPERATION
This chapter deals with the setpoint programming option. All 2408 / 2404 instruments have a basic 8-segment programmer built-in as standard. This facility must be enabled by the user, as explained in the section, Configuring the Programmer.
Other programmer versions are listed below, and have 16-segments in each program.
16-segment programmer with: a single program: Models 2408/CP and 2404/CP. four stored programs: Models 2408/P4 and 2404/P4. twenty stored programs: Models 2408/CM and 2404/CM.
16-segment Motorised Valve programmer with: a single program: Models 2408/VP and 2404/VP. four stored programs: Models 2408/V4 and 2404/V4. twenty stored programs: Models 2408/VM and 2404/VM. The 8-segment programmer differs from the other programmers in that it will not provide event outputs and program synchronisation. Otherwise they all operate in the same way. There are eight topics:
• WHAT IS SETPOINT PROGRAMMING?
• PROGRAMMER STATES
• RUNNING A PROGRAM FROM THE RUN LIST
• RUNNING A PROGRAM USING THE RUN/HOLD BUTTON
• AUTOMATIC BEHAVIOUR
• CONFIGURING THE PROGRAMMER
• CONFIGURING DIGITAL INPUTS TO SELECT PROGRAM NUMBER
• CREATING A NEW PROGRAM, OR MODIFYING AN EXISTING PROGRAM. To understand how to select and change parameters in this chapter you need to have read Chapter 2, Operation and Chapter 3, Access Levels.
Programmer Operation Installation and Operation Handbook
5-2 2408 and 2404 Controller
WHAT IS SETPOINT PROGRAMMING?
Many applications need to vary temperature, or process value, with time. Such applications need a controller which varies a setpoint as a function of time; all 2408 and 2404 models can do this. The setpoint is varied by using a setpoint program. Within each 2408 and 2404 controller, there is a software module called the programmer, which stores one, or more, such programs and drives the setpoint according to the selected program. The program is stored as a series of ‘ramp’ and ‘dwell’ segments, as shown below. (If the 8-segment programmer is being used, then the information in the next paragraph does not apply.) In each segment you can define the state of up to eight (8) digital outputs, each of which can be used to trigger external events. These are called event outputs and can drive either relay, logic, or triac outputs, depending on the modules installed. A program is executed either, once, repeated a set number of times, or repeated continuously. If repeated a set number of times, then the number of cycles must be specified as part of the program.
Fig 5-1 Setpoint profile Time
Setpoint
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-3
There are five different types of segment:
Ramp The setpoint ramps linearly, from its current value to a new value, either at a set rate (called ramp-rate programming), or in a set time (called time-to-target programming). You must specify the ramp rate or the ramp time, and the target setpoint, when creating or modifying a program.
Dwell The setpoint remains constant for a specified period.
Step The setpoint steps instantaneously from its current value to a new value.
Call The main program calls another program as a subroutine. The called program then drives the setpoint until it returns control to the main program. This facility is available on those controllers with 4, or 20, stored programs.
End The program either ends in this segment, or repeats. You specify which is the case when you create, or modify, the program (see the final topic in this chapter). When the program ends, the programmer is put into either, a continuous Dwell state with all outputs staying unchanged, or the Reset state, or to a settable power level.
Table 5-1 Segment Types
Programmer Operation Installation and Operation Handbook
5-4 2408 and 2404 Controller
PROGRAMMER STATES
The programs have five states: Reset, Run, Hold, Holdback and End.
State Description Indication
Reset In Reset, the programmer is inactive and the controller behaves as a standard controller, with the setpoint determined by the value set in the lower readout.
Both the RUN and HOLD lights are OFF
Run In Run, the programmer varies the setpoint according to the active program.
RUN light on
Hold In Hold, the program is frozen at its current point. In this state you can make temporary changes to any program parameter (for example, a target setpoint, a dwell time, or the time remaining in the current segment). Such changes will only remain effective until the program is reset and run again, when they will be overwritten by the stored program values.
Note: When a program is running, you cannot alter a cALLcALLcALLcALLed program until it becomes active within that program.
HOLD light on
Holdback Holdback indicates that the measured value is lagging the setpoint by more than a preset amount and that the program is in Hold, waiting for the process to catch up. See Holdback in the section on Automatic behaviour later this chapter.
HOLD light flashes
A master controller can re-transmit a setpoint value to a number of slave units using PDSIO setpoint retransmission. Any of the slave units can generate a holdback signal which will also flash the HOLD light. Holdback will also occur if the PDSIO output is open circuit. This can be disabled in configuration by selecting the PdS output as SP.nH — ‘setpoint retransmission without holdback’
HOLD light flashes
End The program is complete. RUN light flashes
Table 5-2 Program States
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-5
RUNNING A PROGRAM FROM THE RUN LIST
The Run List
From the Home display, press until you reach the ‘run’ list header.
Press
Program number
This display only appears on programmers that can store more than one program. Use or to select the required program number, from 1 to 4, or 1 to 20, depending on the particular controller. Alternatively, the program number can be selected remotely, using digital inputs on the rear terminals. See the section on Configuring Digital Inputs to Select a Program Number for information on how this is done.
Press
Status selection
Use or to select: • runrunrunrun: Run program. • hoLdhoLdhoLdhoLd: Hold program. • OFFOFFOFFOFF: Program reset. After two seconds, the lower readout blinks and the chosen state is now active.
To return to the Home display press and together.
Other parameters
To access the other parameters in the ‘run’ list, continue to press . These parameters are shown in the ‘Program run list’ in
Chapter 2, Parameter Tables. They show the current status of the active program.
Temporary changes Temporary changes can be made to the parameters in this ‘run’ list, (for example a setpoint, ramp rate, or an unelapsed time), by first placing the programmer into ‘hoLd’. Such changes remain active only for the duration of the segment; the segment parameters will revert to their original (stored) values whenever the segment is re-executed.
Programmer Operation Installation and Operation Handbook
5-6 2408 and 2404 Controller
RUNNING A PROGRAM USING THE RUN/HOLD BUTTON
If you are using a 4, or 20, program version of the controller, you must first select the number of the program that you want to run. Do this in the ‘run’ list − see the previous topic, Running a program from the Run list. Then:
RUN
HOLD
RUN / HOLD button
Press once to run a program (RUN light on) Press again to hold a program (HOLD light on) Press again to cancel hold and continue running (HOLD light off, RUN light on) Press and hold in for two seconds to reset a program (RUN and HOLD lights off).
Note: The RUN/HOLD button can be disabled, either when ordering the controller, or subsequently in configuration. This will force you to operate the programmer from the ‘run’ list all the time. The main advantage of this method is that it will reduce the chance of accidentally changing the state of a program.
AUTOMATIC BEHAVIOUR The preceding topics explain how to operate the programmer manually. The following topics cover aspects of its automatic behaviour: Servo, Holdback and Power Failure. Servo
When a program is RUN, the setpoint can start either from the initial controller setpoint, or from the process value. Whichever it is, the starting point is called the ‘servo’ point and you set it up in configuration. When the program starts, the transition of the setpoint to its starting point is called ‘servoing’.
The normal method is to servo to the process value, because this will produce a smooth and bumpless start to the process. However, if you want to guarantee the time period of the first segment, you should set the controller to servo to its setpoint. Holdback
As the setpoint ramps up, or down (or dwells), the measured value may lag behind, or deviate from, the setpoint by an undesirable amount. ‘Holdback’ is available to freeze the program at its current state, should this occur. The action of Holdback is the same as a deviation alarm. It can be enabled, or disabled. Holdback has two parameters — a value and a type. If the error from the setpoint exceeds the set ‘holdback’ value, then the Holdback feature, if enabled, will automatically freeze the program at its current point and flash the HOLD light. When the error comes within the holdback value, the program will resume normal running.
There are four different Holdback types. The choice of type is made by setting a parameter when creating a program, and may be one of the following:− ‘OFF’ − Disables Holdback − therefore no action is taken.
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-7
‘Lo’ − Deviation Low Holdback holds the program back when the process variable deviates below the setpoint by more than the holdback value.
‘Hi’ − Deviation High Holdback holds the program back when the process variable deviates above the setpoint by more than the holdback value.
‘bAnd’ − Deviation Band Holdback is a combination of the two. It holds the program back when the process variable deviates either above, or below, the setpoint by more than the holdback value.
There is a single Holdback Value which applies to the whole program. However, the Holdback type and whether or not it is enabled, can be applied to the program as a whole, or individually in each segment.
Power failure
If power is lost and then restored, while a program is running, the behaviour of the programmer is determined by the setting of the parameter ‘Pwr.F’ Power fail strategy in Programmer configuration. This can have one of three settings:− cont (Continue), rmP.b (Ramp from PV), or rSEt (Reset).
If ‘cont’ is selected, then when power is restored the program continues from where it was interrupted when power was lost. All parameters, such as the setpoint and time remaining in the active segment, will be restored to their power-down values. For applications that need to bring the measured process value to the setpoint as soon as possible, this is the best strategy.
If ‘rmP.b’ is selected, then when power is restored the setpoint starts at (‘servos to’) the current measured value, and then ramps to the target setpoint of the active segment at the last ramp rate used by the program. This strategy provides a smoother recovery. The two diagrams below illustrate the respective responses, Fig 5-2 if power fails during a dwell segment and Fig 5-3 if it fails during a ramp segment.
Figure 5-2 Continue after a power fail
Figure 5-3 Ramp back after a power fail
If ‘rSEt’ is selected, then when power is restored the program terminates.
Setpoint
Ramp Segment Dwell Segment
Time
t1 t2
Segment dwell time = t1 + t2
Power off Power on
Setpoint
Ramp Segment
Time
Power off
Power on — Servo to new PV level
Target setpoint
Programmer Operation Installation and Operation Handbook
5-8 2408 and 2404 Controller
CONFIGURING THE PROGRAMMER When first installing a programmer you should check that the configuration conforms to your requirement. Configuration defines: • the number of stored programs (multi-programmer only) • the holdback strategy • the power fail strategy • the servo type • if event outputs are available (not 8-segment programmer) • if program synchronisation is available. (not 8-segment programmer) • selection of program number using digital inputs (multi-programmer only)
To check, or change, the configuration, select Configuration level. See Chapter 6.
Programmer list header
After selecting Configuration mode, press until the PROG ConF header is displayed.
Press
Number of programs
Use or to select: •••• nonE: Disable built-in 8-segment programmer •••• 1: Enable built-in 8-segment programmer
For 16-segment programmers: •••• nonEnonEnonEnonE: no programs •••• 1: One stored program •••• 4: Four stored programs • 20: Twenty stored programs
Press
Holdback Strategy
Use or to select: • SEG: Holdback type to be set in each segment • ProG: Holdback type to be set for the whole program
Press Continued on the next page.
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-9
Power fail strategy
Use or to select • cont: Continue from last setpoint • rmP.b: Ramp from PV to setpoint at last ramp rate • rSEt: Reset the program.
Press
Servo type
Use or to select: • to.PV: Servo to PV • to.SP: Servo to SP
Press
Event Outputs (not in 8-segment programmer)
Use or to select: • no: Event outputs disabled • YES: Event outputs enabled
Press
Synchronisation (not in 8-segment programmer) Use or to select: • no: Synchronisation disabled • YES: Synchronisation enabled
Press to return the list header.
Programmer Operation Installation and Operation Handbook
5-10 2408 and 2404 Controller
CONFIGURING DIGITAL INPUTS TO SELECT PROGRAM NUMBER
The program number can be selected by external BCD inputs from, for example, a thumbwheel switch. The appropriate number of digital inputs must be installed in the controller and be configured for this function — see Chapter 6, Configuration. To invoke this mode of operation, the parameter ‘bcd’ in ‘inst-Conf’ must be set to ‘PrOg’.
bcd
PrOG
Press until you reach ‘bcd’.
Use the or buttons, to select ‘PrOG’.
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-11
CREATING A NEW PROGRAM, OR MODIFYING AN EXISTING ONE
The only difference between creating a new program, and modifying an existing one, is that a new program starts with all its segments set to End in the tYPE parameter. The procedure for both consists of setting up the parameters in the PrOG list of the Operator Navigation Diagram shown in Chapter 2. As explained earlier under ‘Programmer states’, temporary changes can be made to these parameters while in the HOLD state but permanent changes (to the stored values) can only be made when the programmer is in the Reset state. So, before modifying a stored program first make sure that it is in Reset and then follow the procedure below.
Program edit list
From the Home display press until you reach the ProG LiSt header.
Press
Program number This display appears only on the multi-program controllers. Use or to select the number of the program which you wish to modify (from 1 to 4, or 1 to 20).
Press Holdback type [Only appears when Holdback has been selected for the whole program.] Use or to select: • OFF: Holdback disabled • Lo: Deviation Low Holdback • Hi: Deviation High Holdback • bAnd: Deviation Band Holdback
Press
Holdback value Note! The value set in this parameter is always for the whole program. Use or to set the value.
Press Continued on the next page.
Programmer Operation Installation and Operation Handbook
5-12 2408 and 2404 Controller
Ramp units
Use or to select: • Sec • min • Hour
Press
Dwell units
Use or to select: • Sec • min • Hour
Press
Number of program cycles
Use or to set the number of program cycles required from 1 to 999, or ‘cont’ for continuous cycling.
Press
Segment number
Use or to select the number, from 1 to 16. (1 to 8 in 8-segment programmers) The parameters that follow ‘SEG.n’ set up the characteristics of the individually-selected segment number. By defining the characteristics of each segment of the program, you define the whole program.
Press
Continued on the next page.
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-13
Segment type
Select the segment type using or : • rmP.r: Ramp to a new setpoint at a set rate • rmP.t: Ramp to a new setpoint in a set time • dwEl: Dwell for a set time • StEP: Step to a new setpoint • cALL: Call another program as a subroutine (only available in multi-program controllers) • End: Make this segment the end of the program.
Press
The parameters that follow ‘tYPE’ depend on the type of segment selected as shown in the table below. The function of each parameters follows the table.
Parameter Segment type selected
rmP.r rmP.t dwEl StEP cALL EndEndEndEnd
Hb ! ! ! ! tGt ! ! !
rAtE !
dur ! !
PrG.n !
cYc.n !
outn ! ! ! ! !
SYnc ! ! ! !
End.t !
Pwr !
Table 5-3 Parameters that follow segment type
Holdback type Only appears when Holdback per segment has been selected. Use or to select: • OFF: Holdback disabled • Lo: Deviation Low Holdback • Hi: Deviation High Holdback • bAnd: Deviation Band Holdback
Press
Target setpoint
Target setpoint for ‘rmP.r’, ‘rmP.t’ or ‘StEP’ segments. Set the target setpoint using or .
Press Continued on the next page.
Programmer Operation Installation and Operation Handbook
5-14 2408 and 2404 Controller
Ramp rate
Ramp rate for ‘rmP.r’ segments Using or , set a value for the ramp rate, ranging from 0.0 to 999.9. The units are the ramp units (rmP.U) set earlier in this sequence.
Press
Duration time
Time for a ‘dwEl’ segment, or time to target for a ‘rmP.t’ segment. Set the time using or . You have set the units earlier in this sequence. [‘dwL.U’ defines the units for ‘dwEl’ segments: ‘rmP.U’ defines the units for ‘rmP.t’ segments.]
Press
Called program number
Only appears for ‘cALL’ segments. (multi-program controllers only) Set a called program number from 1 to 4, or from 1 to 20, using
or .
Press
Number of cycles of the cALLed program
Only appears for ‘cALL’ segments. (multi-program controllers only) Sets the number of cycles of the cALLed program from 1 to 999, using or .
Press
Continued on the next page.
Installation and Operation Handbook Programmer Operation
2408 and 2404 Controller 5-15
Event output 1 (16-segment programmers only)
Appears in all segments, except ‘cALL’ segments. Use or to set output 1: • OFF: Off in the current segment • on: On the current segment.
Press
Further event outputs (16-segment programmers only)
Up to eight (8) event outputs may appear in this list where ‘n’ = event number. Pressing will step through all the remaining event outputs. Note: If you are not using all of the event outputs, you can step immediately to the next segment number by pressing .
Press
Synchronisation event output (only appears if configured)
Use or to select: • YES: Synchronisation Enabled • no: Synchronisation Disabled
Note: This event output, if used, occupies the position of ‘out8’.
Press
End segment
Use or to select: • dwEl: An indefinite dwell • rSEt: Reset. • S OP: End Segment Output Power Level
Press
SYnc
YES
Programmer Operation Installation and Operation Handbook
5-16 2408 and 2404 Controller
Power Value [End Segment]
Use or to set the power value in the range ±100.0%. This power level is clipped by the parameters ‘OP.Hi’ and ‘OP.Lo’ before being applied to the process. Note: In programmer/controller software versions 3.56 onwards this parameter has been replaced by a parameter End.PEnd.PEnd.PEnd.P which appears at the end of the Output List, see Chapter 2
Press to return to the ProG-LiSt header.
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-1
Chapter 6 CONFIGURATION
This chapter consists of six topics:
• SELECTING CONFIGURATION LEVEL
• LEAVING CONFIGURATION LEVEL
• SELECTING A CONFIGURATION PARAMETER
• CHANGING THE PASSWORDS
• NAVIGATION DIAGRAM
• CONFIGURATION PARAMETER TABLES. In configuration level you set up the fundamental characteristics of the controller. These are:
• The type of control (e.g. reverse or direct acting)
• The Input type and range
• The Setpoint configuration
• The Alarms configuration
• The Programmer configuration
• The Digital input configuration
• The Alarm Relay configuration
• The Communications configuration
• The Modules 1, 2 & 3 configuration
• Calibration
• The Passwords.
WARNING Configuration is protected by a password and should only be carried out by a qualified person, authorised to do so. Incorrect configuration could result in damage to the process being controlled and/or personal injury. It is the responsibility of the person commissioning the process to ensure that the configuration is correct.
Configuration Installation and Operation Handbook
6-2 2408 and 2404 Controller
SELECTING CONFIGURATION LEVEL
There are two alternative methods of selecting Configuration level: • If you have already powered up, then follow the access instructions given in Chapter 3,
Access levels.
• Alternatively, press and together when powering up the controller. This will take you directly to the ‘ConF’ password display.
Password entry
When the ‘ConF’ display appears, you must enter the Configuration password (which is a number) in order to gain access to Configuration level.
Enter the password using the or buttons. The configuration password is set to ‘2’ when the controller is shipped from the factory. Once the correct password has been entered, there is a two second delay, after which the lower readout will change to ‘PASS’ indicating that access is now unlocked. Note: A special case exists if the password has been set to ‘0’. In this situation, access is permanently unlocked and the lower readout will always show ‘PASS’. Press to enter configuration. (If an incorrect password has been entered and the controller is still ‘locked’ then pressing at this point will take you to the ‘Exit’ display with ‘no’ in the lower readout. Simply press to return to the ‘ConF’ display.) You will obtain the first display of configuration.
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-3
LEAVING CONFIGURATION LEVEL To leave the Configuration level and return to Operator level Press until the ‘Exit’ display appears.
Alternatively, pressing and together will take you directly to the ‘Exit’ display.
Use or to select ‘YES’. After a two-second delay, the display will blank and revert to the Home display in Operator level.
SELECTING A CONFIGURATION PARAMETER The configuration parameters are arranged in lists as shown in the navigation diagram in Figure 6.1.
To step through the list headers, press the Page button.
To step through the parameters within a particular list press the Scroll button. When you reach the end of the list you will return to the list header.
You can return directly to the list header at any time by pressing the Page button. Parameter names Each box in the navigation diagram shows the display for a particular parameter. The upper readout shows the name of the parameter and the lower readout its value. For a definition of each parameter, see the Configuration Parameter Tables at the end of this chapter. To change
the value of a selected parameter, use the and buttons. The navigation diagram shows all the lists headers and parameters that can, potentially, be present in the controller. In practice, those actually present will vary according to the particular configuration choices you make.
CHANGING THE PASSWORDS
There are TWO passwords. These are stored in the Password configuration list and can be selected and changed in the same manner as any other configuration parameter. The password names are: ‘ACC.P’ which protects access to Full level and Edit level ‘cnF.P’ which protects access to Configuration level.
Configuration Installation and Operation Handbook
6-4 2408 and 2404 Controller
NAVIGATION DIAGRAM (PART A) Instrument Process Value Input Setpoint Alarms Programmer Logic inputs Config Config Config Config Config Config Config
Fig 6.1a Navigation Diagram (Part A)
m-A diSA
ti.td SEc
CooL Lin
Act rEv
CtrL Pid
inSt ConF
rmt nonE
rmP.U PSEc
Pr.tr OFF
m.tr OFF
rm.tr OFF
nSP 2
SP ConF
AL ConF
AL1 FSH
Ltch no
bLoc no
AL2 FSL
Ltch no
bLoc no
AL3 OFF
Ltch no
bLoc no
AL4 OFF
Ltch no
bLoc no
PROG ConF
PtyP 20
Pwr.F cont
Srvo to.PV
out no
SYnc no
iP ConF
id LoG.i
Func mAn
LA/b ConF
inPt k.tc
CJC Auto
inp.L 0.0
VaL.H 100.0
VaL.L 0.0
inp.H 50.0
imp Auto
HbAc SEG
unit oC
dEc.P nnnn
PV ConF
rnG.H 1200
rnG.L 0
FOP no
Sbr.t Sb.OP
Pd.tr no
Fwd.t nonE
PwrF YES
r-h diSA
GSch no
bcd nonE
dtYP PV
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-5
NAVIGATION DIAGRAM (PART B) Alarm relay Comms 1 Comms 2 Module 1 Module 2 Module 3 Module 4(2) Custom(3) Config Config Config Config(1) Config(1) Config(1) Config Config
Fig 6.1b Navigation Diagram (Part B)
Note: 1. Additional headers, carrying the suffixes b
and C, will appear if dual-, or triple-, channel modules have been installed. The header denotes the labelling of the terminal to which the output function is connected.
2. Module 4 is the High Current Switch Module. This is only available in the Model 2404 controller on controllers manufactured before Jan-04.
3. 8-point custom linearisation. Only appears when either‘3a or iP-Conf’ has ‘inpt’ = ‘mV.C’, or ‘mA.C’, or ‘V.C’.
4. The navigation diagram shows typical parameters, but is dependant upon the exact configuration of the instrument. The following sheets show the full list of parameters.
See parameter tables
id dC.OP
Func HEAt
VAL.L 0
VAL.H 100
unit mA
Out.L 4.0
Out.H 20.0
rES FuLL
Prty nonE
bAud 9600
Func mod
id cmS
in 1 0.0
UAL.1 0.0
in 2 1.0
UAL.2 200.0
in 3 2..0
VAL.H 100
VAL.L 0
Func SP.oP
id PdS
id rELy
Func dIG
SEnS nor
2A ConF
1A ConF
3A ConF
HA ConF
CUSt ConF
JA ConF
AA ConF
See parameter tables
id dC.iP
Func SEL
inpt mU
imp Auto
inp.L 0.0
inp.H 50.0
VAL.L 0
VAL.H 100
4A ConF
id HCS
Func HEAt
VAL.L 0
VAL.H 100
Out.L 0.0
Out.H 100.0
UAL.3 350.0
in 8 7.0
UAL.8 800.0
deLY no
SEnS nor
Configuration Installation and Operation Handbook
6-6 2408 and 2404 Controller
NAVIGATION DIAGRAM (PART C) Calibration Password Config Config
Fig 6.1c Navigation Diagram (Part C)
ACC.P 1
cnF.P 2
Exit no
PASS ConF
cAL nonE
UCAL no
pt1.L 0
pt1.H 0
OF1.L 0.0
CAL ConF
OF1.H 0.0
pt2.L 0
pt2.H 0
OF2.L 0.0
OF2.H 0.0
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-7
CONFIGURATION PARAMETER TABLES
Name Description Values Meaning
inStinStinStinSt Instrument configuration
CtrL Control type Pid PID control On.OF On/off control VP Boundless motorised valve
control — no feedback required VP b Bounded motorised valve
control — feedback required
Act Control action rEv Reverse acting dir Direct acting CooL Type of cooling Lin Linear oiL Oil (50mS minimum on-time) H2O Water (non-linear) FAn Fan (0.5S minimum on-time) on.OF On/off cooling ti.td Integral & derivative SEc Seconds, OFF to 9999 time units min Minutes, OFF to 999.9 dtYP Derivative type pV
Err Operates on rate of change of PV Operates on rate of change of error
m-A Front panel Auto/Man button EnAb Enabled diSA Disabled r-h Front panel Run/Hold button EnAb Enabled diSA Disabled PwrF Power feedback on On OFF Off Fwd.t Feed forward type none None FEEd Normal feed forward SP.FF Setpoint feed forward PV.FF PV feed forward Pd.tr Manual/Auto transfer when no Non-bumpless transfer using PD control YES Bumpless transfer — (Pre-loads
Manual Reset value) Sbr.t Sensor break output Sb.OP Go to pre-set value HoLd Freeze output FOP Forced manual output no Bumpless Auto/Manual transfer trac Returns to the Manual value that
was set when last in Manual mode
Step Steps to forced output level. Value set in ‘FOP’ of ‘op-List’ in Operator Level
bcd BCD input function none prog sp
Not used Select program number Select setpoint number
gsch Gain schedule enable no yes
Disabled Enabled
Configuration Installation and Operation Handbook
6-8 2408 and 2404 Controller
Name Description Values Meaning
pVpVpVpV Process value config unit Instrument units 0C Celsius 0F Fahrenheit 0k
none Kelvin Display units blanked
dec.p Decimal places in the nnnn None displayed value nnn.n
nn.nn One Two
rng.L Range low Low range limit. Also setpoint limit for alarms and programmers
rng.h Range high High range limit. Also setpoint limit for alarms and programmers
Notes:
1. Pyrometer Emmisivity
Controllers which are specifically supplied for pyrometer inputs (not Exergen K80), have the curve downloaded in the Custom Input. The parameter, EmiS, Pyrometer Emmisivity, appears in the Input List on page 2-15. This parameter is also now correctly adjusted.
2. Range
If a decimal point was configured, negative display and setpoint ranges were limited to -99.9 in previous software versions. The range has been increased to -199.9 by combining the negative sign with the figure one. This allows Setpoints, Process Variables, Alarm Setpoints and Programmers to be set to -199.9.
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-9
Name Description Values Meaning
iPiPiPiP Input configuration inPt Input type J.tc J thermocouple k.tc K thermocouple L.tc L thermocouple r.tc R thermocouple (Pt/Pt13%Rh) b.tc B thermocouple (Pt30%Rh/Pt6%Rh) n.tc N thermocouple t.tc T thermocouple S.tc S thermocouple (Pt/Pt10%Rh) PL 2 PL 2 thermocouple C.tc Custom downloaded t/c (default = type C) rtd 100Ω platinum resistance thermometer mV Linear millivolt voLt Linear voltage mA Linear milliamps Sr V Square root volts Sr A Square root milliamps * see CUST List. mV.C 8-point millivolt custom linearisation* V.C 8-point Voltage custom linearisation* mA.C 8-point milliamp custom linearisation*
CJC Cold Junction Auto Automatic internal compensation Compensation 0oC 0oC external reference 45oC 45oC external reference 50oC 50oC external reference OFF No cold junction compensation
imp Sensor Break Impedance Off Disabled (applies to any input) Caution: If sensor break is disabled the controller will not detect open circuit faults
Auto Factory set (Default i.e. enabled) Hi Impedance of input > 5KΩ Hi.Hi Impedance of input > 15KΩ Linear Input Scaling − The next 4 parameters only appear if a linear or sq rt input is chosen.
inp.L Input value low
inp.H Input value high
VAL.L Displayed reading low
VAL.H Displayed reading high
inP.H inP.L
VAL. H
Displayed Value
VAL. L Electrical Input
Configuration Installation and Operation Handbook
6-10 2408 and 2404 Controller
Name Description Values Meaning
SPSPSPSP Setpoint configuration
nSP Number of setpoints 2, 4, 16 Select number of setpoints available
rm.tr Remote Tracking OFF Disable trAc Local setpoint tracks remote setpoint
m.tr Manual Track OFF Disable trAc Local setpoint tracks PV when in manual
Pr.tr Programmer Track OFF Disable trAc Local setpoint tracks programmer SP
rmP.U Setpoint rate limit units PSEc Per second Pmin Per minute PHr Per hour
rmt Remote setpoint configuration nonE Disable SP Remote setpoint Loc.t Remote setpoint + local trim rmt.t Remote trim + local setpoint
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-11
ALALALAL Alarm configuration Values
The controller contains four ‘soft’ alarms, which are configured in this list. Once configured, they can be attached to a physical output as described in the alarm relay configuration list, ‘AA Conf’.
AL1 Alarm 1 Type see Table A
Ltch Latching no/YES/Evnt/mAn*
bLoc Blocking no/YES
AL2 Alarm 2 Type see Table A
Ltch Latching no/YES/Evnt/mAn*
bLoc Blocking no/YES
AL3 Alarm 3 Type see Table A
Ltch Latching no/YES/Evnt/mAn*
bLoc Blocking no/YES
AL4 Alarm 4 Type see Table A
Ltch Latching no/YES/Evnt/mAn*
bLoc Blocking (not if ‘AL4’ = ‘rAt’) no/YES
Sbr.t Sensor break trip alarm latching type. Disable = process alarms inhibited when in sensor break Enable = process alarms shown when in sensor break
En Enable
Dis Disable
* Alarm Modes ‘no’ means that the alarm will be non-latching. ‘YES’ means that the alarm will be latched, with automatic resetting. Automatic resetting means that if a reset is actioned before the alarm has cleared, then it will automatically reset when it clears. Evnt’ means that the alarm is used to trip an external event. If this option is selected the front panel alarm message will not appear. ‘mAn’ means that the alarm will be latched, and can only be reset after it has first cleared (called ‘manual reset mode’).
Table A — Alarm types Value Alarm type
OFF No alarm
FSL PV Full scale low
FSH PV Full scale high
dEv PV Deviation band
dHi PV Deviation high
dLo PV Deviation low
LCr Load Current low
HCr Load Current high
FL2 Input 2 Full Scale low
FH2 Input 2 Full Scale high
LOP Working Output low
HOP Working Output high
LSP Working Setpoint low
HSP Working Setpoint high
rAt PV Rate of change AL4 only
Ct.OP CT open circuit
Ct.Sh CT short circuit
Configuration Installation and Operation Handbook
6-12 2408 and 2404 Controller
The following parameters apply if the standard 8-segment programmer is to be configured.
PROGPROGPROGPROG Programmer configuration Values Meaning
PtyP Programmer type nonE Programmer disabled (factory setting) 1 8-segment programmer enabled
HbAc Holdback SEG
ProG
Holdback is individually selectable in each segment. Holdback is applied across the whole Program.
Pwr.F Power fail recovery cont Continue from last setpoint (SP) rmP.b Ramp from PV to SP at last ramp rate rSEt Reset the program
Srvo Starting setpoint of a to.PV From the Process Value (PV) program (Servo point) to.SP From the setpoint
The following parameters apply if a 16-segment programmer is to be configured.
PROGPROGPROGPROG Programmer configuration Values Meaning
PtyP Programmer type nonE Programmer disabled 1 Single program
4 Four programs
20 Twenty programs
HbAc Holdback SEG
ProG
Holdback is individually selectable in each segment. Holdback is applied across the whole Program.
Pwr.F Power fail recovery cont Continue from last setpoint (SP) rmP.b Ramp from PV to SP at last ramp rate
rSEt Reset the program
Srvo Starting setpoint of a to.PV From the Process Value (PV) program (Servo point) to.SP From the setpoint
out Programmable event outputs
no YES
Disabled Enabled
SYNC Synchronisation of programs of several programmers
no YES
Disabled Enabled
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-13
Name Description Values Meaning
LALBLALBLALBLALB Digital input 1/2 configuration Action on contact closure
id Identity LoG.i Logic input
Func Function of input nonE No function The function is active mAn Manual mode select when the input has a contact rmt Remote setpoint select closure to the common SP.2 Setpoint 2 select terminal — LC Pid.2 PID set 2 select ti H Integral hold tunE One-shot self-tune enable drA Adaptive tune enable Ac.AL Acknowledge alarms AccS Select Full access level Loc.b Keylock uP Simulate pressing of the button dwn Simulate pressing of the button ScrL Simulate pressing of the button PAGE Simulate pressing of the button run Run program HoLd Hold program r-H Run program (closed) / Hold (open) rES
SkiP Reset program Skip to End of Current Segment, without changing the setpoint
HbAc Program holdback enabled These BCD inputs are used to bcd.1 Least significant BCD digit select either a program number bcd.2 2nd BCD digit or the setpoint number bcd.3 3rd BCD digit according to the setting of the bcd.4 4th BCD digit parameter ‘bcd’ in the ‘inSt’ bcd.5 5th BCD digit configuration list bcd.6 Most significant BCD digit rmP.E Setpoint Rate Limit Enable SYnc Program waits at the end of the
current segment rrES Program Run (closed) / Reset (open) rESr Program Reset (closed) / Run (open) Stby Standby — ALL control outputs turned
OFF (alarm Outputs are not affected) PV.SL PV Select:
Closed = PV1 / Open = PV2 AdV Advance to End of Segment and to
Target Setpoint PrGn Program number AmPS Current – LB only
Configuration Installation and Operation Handbook
6-14 2408 and 2404 Controller
Name Description Values Meaning
AAAAAAAA Alarm relay configuration
id Identity rELy Relay output
Func Function nonE No function dIG Digital output
SEnS Digital output sense nor Normal (output energises when TRUE, e.g. program events)
inv Inverted (output de-energises when TRUE, e.g. alarms)
The following digital events appear after ‘SEnS’. Any one, or more, of the events can be combined on to the output (see Fig. 6-2) by selecting ‘YES’ in the lower readout.
1 — — — Alarm 1 active YES / no (- — -) = alarm type (e.g. FSL).
2 — — — Alarm 2 active YES / no If an alarm has not been configured
3 — — — Alarm 3 active YES / no in ‘AL ConF’ list, then display will
4 — — — Alarm 4 active YES / no differ:- e.g. Alarm 1 = ‘AL 1’.
mAn Controller in manual mode YES / no
Sbr Sensor break YES / no
SPAn PV out of range YES / no
Lbr Loop break YES / no
Ld.F Load failure alarm YES / no
tunE Tuning in progress YES / no
dc.F Voltage output open circuit, or mA output open circuit
YES / no
rmt.F PDS module measurement connection or remote input open circuit
YES / no
iP1.F Input 1 failure YES / no
nw.AL New Alarm has occurred YES / no
End End of setpoint rate limit, or end of program
YES / no
SYnc Program Synchronisation active YES / no
PrG.n Programmer event output active, where ‘n’ = event number from 1 to 8. (Not available with 8-segment programmer.)
YES / no
Figure 6-2 Combining several digital events on to one output
dIG SEnS
nor
inv Output Module
Digital Events
OR
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-15
Name Description Values Meaning
HAHAHAHA Comms 1 module config
id Identity of the module installed cmS EIA-232, or 2-wire EIA-485, or 4-wire EIA-485 comms
PDS PDS retransmission PDS.i PDS input dnET DeviceNet
For ‘idididid’ = ‘cms’ (Digital communications) use this parameter table: Func Function mod Modbus protocol EI.bi Bisynch protocol
bAud Baud Rate 1200, 2400, 4800, 9600, 19.20(19,200) 125(K), 250(K), 500(K) for DeviceNet
dELy Delay — quiet period, required by no No delay some comms adaptors YES Delay active — 10mS
The following parameters only appear if the function chosen is Modbus protocol.
Prty Comms Parity nonE No parity EvEn Even parity Odd Odd parity
rES Comms Resolution FuLL Full resolution Int Integer resolution
For ‘idididid’ = ‘pds’ (PDS retransmission output) use this parameter table: Func Function nonE No PDS function i.e. Retransmitted output SP.oP PDS setpoint retransmission PV.oP PDS PV retransmission OP.oP PDS output power retransmission Er.OP PDS error signal retransmission SP.nH PDS setpoint retransmission — no
holdback
Output Scaling
VAL.L Retransmitted value low
VAL.H Retransmitted Value High VAL.L
100% 0%
VAL.H
Displayed Value
Retransmitted Output
Configuration Installation and Operation Handbook
6-16 2408 and 2404 Controller
Name Description Values Meaning
For ‘idididid’ = ‘Pdsi’ (PDS setpoint input) use this parameter table:
Func Function SP.iP PDS setpoint input
VAL.L Setpoint Displayed Value — Low
VAL.H Setpoint Displayed Value — High
Note: Having configured the module function as remote setpoint you must then specify the type of remote setpoint in the SP-conf list
JAJAJAJA Comms 2 module config As per Comms 1 module configuration
VAL.L 100% 0%
VAL.H
Displayed Value
Electrical Input
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-17
Name Description Values Meaning
1A1A1A1A/bbbb/CCCC(1) Module 1 configuration
id Identity of module installed nonE Module not fitted
rELy Relay output dC.OP DC output isolated and non-
isolated (1) If a dual-, or triple-, channel LoG Logic/PDS output module is installed then the list LoG.i Logic input headers 1b and 1C also appear SSr Triac output dc.rE DC retransmission (isolated) dc.OP Isolated DC output SG.SU Transducer power supply
For ‘idididid’ = ‘rELy’, ‘LoG’, or ‘SSr’ use this parameter table: Func Function nonE Function disabled
dIG Digital output function
(Only Channels 1A and 1C can be HEAt Heating output
Heating, or Cooling) COOL Cooling output
up Open motorised valve
dwn Close motorised valve
(Only if ‘id’ = ‘LoG’) SSr.1 PDS mode 1 heating
(Only if ‘id’ = ‘LoG’) SSr.2 PDS mode 2 heating
VAL.L % PID demand signal giving minimum output − ‘Out.L’
VAL.H % PID demand signal giving maximum output − ‘Out.H’
Out.L Minimum average power
Out.H Maximum average power
SEnS Sense of output (Only if ‘Func’ = ‘dIG’)
nor Normal (output energises when TRUE, e.g program events)
inv Inverted (output de-energises when TRUE, e.g. alarms)
Notes:
1. When ‘SEnS’ appears, then further parameters are available. These are identical to those in the ‘AA ConF’ list on Page 6-14.
2. If a Tranducer Power Supply is fitted, the SenS parameter selects the output voltage. nor = 5V, inv = 10V
3. A Transducer Power Supply does not provide any calibration facility and is simply a 5 or 10V power supply.
4. To invert a PID output, the Val. H can be set below the Val.L f
VAL.L Out.H Out.L
VAL.H
PID Demand Signal
ElectricalOutput
Configuration Installation and Operation Handbook
6-18 2408 and 2404 Controller
Name Description Values Meaning
For ‘idididid’ = ‘dC.OP’, ‘dc.rE’, or ‘dc.OP’ use this parameter table:
Func Function nonE Function disabled HEAt Heating output COOL Cooling output PV Retransmission of PV wSP Retransmission of setpoint Err Retransmission of error signal OP Retransmission of OP power
VAL.L % PID, or Retrans’n Value, giving minimum output
VAL.H % PID, or Retrans’n Value, giving maximum output
unit voLt = Volts, mA = milliamps
Out.L Minimum electrical output
Out.H Maximum electrical output
For ‘idididid’ = ‘LoG.i’ (i.e logic input) use the LALALALA Conf’ list on Page 6-13.
2A2A2A2A/bbbb/CCCC Module 2 configuration
As per module 1 configuration, but excluding the ‘SSr.1’, ‘SSr.2’ functions.
id Identity of module installed. As per module 2 plus: tPSU Transmitter power supply Pot.i Potentiometer input
For ‘idididid’ = ‘Pot.i (i.e. potentiometer input module) use this parameter table:
Func Function nonE Function disabled rSP Remote Setpoint
Fwd.i Feedforward input
rOP.h Remote OP power max.
rOP.L Remote OP power min.
VPoS Motorised valve position
VAL.L Displayed value low equivalent to 0% potentiometer position
VAL.H Displayed value high
equivalent to 100% potentiometer position
VAL.L Out.H Out.L
VAL.H
Electrical Output
%PID, or Retransmission Value
VAL.L 100% 0%
VAL.H
Displayed value
Potentiometer position
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-19
3A3A3A3A/bbbb/CCCC Module 3 configuration
As per module 2 configuration, plus ‘id’ = ‘dC.iP’
For ‘idididid’ = ‘dC.iP’ use this parameter table. THIS INCLUDES THE SECOND PV FUNCTIONS
Func Function nonE Function disabled rSP Remote Setpoint
Fwd.i Feedforward input
rOP.h Remote OP power max.
rOP.L Remote OP power min.
Hi PV = The highest of iP.1, or iP.2 Lo PV = The lowest of iP.1, or iP.2 Ftn Derived function, where
PV = (f.1 x iP1) + (f.2 x iP2). ‘F.1’ and ‘F.2’ are scalars which are found in ‘ip-List’ of Operator Level
SEL Select ip.1, or ip.2 via Comms, front panel buttons, or a digital input
trAn Transition of control between ip.1 and ip.2. The transition region is set by the values of ‘Lo.Ip’ and ‘Hi.Ip’, which are found in ‘ip-List’ of Operator Level. PV = ip.1 below ‘Lo.Ip’ PV = ip.2 above ‘Hi.Ip’
inpt Input type Refer to ‘ip Conf’ for all types, + the following:
HiIn High Impedance (range = 0 to 2 volt)
CJC Cold Junction OFF No cold junction compensation Compensation Auto Automatic internal compensation 0oC 0oC external reference 45oC 45oC external reference 50oC 50oC external reference
imp Sensor Break Impedance Off Disabled (applies to any input) Caution: If sensor break is disabled the controller will not detect open circuit faults
Auto Factory set Hi Impedance of input > 15KΩ Hi.Hi Impedance of input > 30KΩ Linear Input Scaling − The next four parameters only appear if a linear input is chosen.
inP.L Input value low
inP.H Input value high
VAL.L Displayed value low
VAL.H Displayed value high VAL.L
inP.H inP.L
VAL.H
Displayed Value
Electrical Input
Configuration Installation and Operation Handbook
6-20 2408 and 2404 Controller
Name Description Values Meaning
4A4A4A4A Module 4 configuration
Note: This option is not available on controllers from 01 Jan-04
id Identity of module installed HCS High Current Switch
Func Function nonE Function disabled dIG Digital output function
HEAt Heating output
COOL Cooling output
VAL.L % PID demand signal giving minimum output − ‘Out.L’
VAL.H % PID demand signal giving maximum output − ‘Out.H’
Out.L Minimum electrical output
Out.H Maximum electrical output
SEnS Sense of output (Only if ‘Func’ = ‘dIG’)
nor Normal (output energises when TRUE, e.g. program events)
inv Inverted (output de-energises when TRUE, e.g. alarms)
When ‘SEnS’ appears, then further parameters are available.
These are identical to those in the ‘AA ConF’ list on Page 6-14.
Cust 8-point Custom Linearisation (1)
in 1 Custom input 1
VAL.1 Linearisation Value representing in 1
in 8 Custom input 8
VAL.8 Linearisation Value representing in 8
VAL.L
Out.H Out.L
VAL.H
PID Demand Signal
ElectricalOutput
Note: 1. Custom Linearisation is only available when ‘3a-Conf’or iP- ConF list
has ‘inpt’ set to ‘mV.C’, or ‘mA.C’, or ‘V.C’. 2. The values and inputs must be continuously increasing or decreasing
VAL.1 VAL.3
in 8 in 1 in 3
VAL.8
Displayed Value
Electrical Input
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-21
Name Description Values Meaning
CALCALCALCAL Calibration
In this mode you can 1. Calibrate the instrument using a mV source — rcAL or ref source
cal. 2. Offset the calibration to account for errors in actual sensor
measurement and a ref sensor — UCAL or user calibration 3. Return to factory set calibration — FACT or factory set calibration.
rcAL Calibration point
nonE No calibration
PV Calibrate main Process Value input. PV.2 Calibrate DC input, or PV 2. 1A.Hi Calibrate DC output high — Module 1 1A.Lo Calibrate DC output low — Module 1 2A.Hi Calibrate DC output high — Module 2 2A.Lo Calibrate DC output low — Module 2 3A.Hi Calibrate DC output high — Module 3 3A.Lo Calibrate DC output low — Module 3
INPUT CALIBRATION For ‘CAL’ = ‘PV’, or ‘PV.2’, the following parameters apply.
PV PV Calibration Value IdLE Idle
mv.L Select 0mV as the calibration point
mv.H Select 50mV as the calibration point
V 0 Select 0Volt as the calibration point
1. Select calibration value V 10 Select 10V as the calibration point
2. Apply specified input CJC Select 0oC CJC calibration point
3. Press to step to ‘GO’ rtd Select 400Ω as the calibration point
HI 0 High impedance: 0Volt cal’n point
HI 1.0 High impedance: 1.0 Volt cal’n point
See Note below. FACt Restore factory calibration
GO Start calibration no Waiting to calibrate PV point
Select ‘YES’ with or YES Start calibration
Wait for calibration to buSy Busy calibrating complete. donE PV input calibration completed FAIL Calibration failed
Note. When a DC input module is installed for the first time, or there is a requirement to change one, then the microprocessor in the controller needs to read the factory calibration data stored in the module. Select ‘FACt’ as the calibration value. Step to ‘GO’ and start calibration.
Goto User calibration table-See also chapter 7
Go to input Calibation table
Go to DC Output Calibration table
Configuration Installation and Operation Handbook
6-22 2408 and 2404 Controller
DC Output Calibration The following parameters apply to DC output modules ie for rcAL = 1A.Hi to 3A.Lo cAL.H Output Calibration High 0 0 = Factory set calibration.
Trim value until output = 9V, or 18mA
cAL.L Output Calibration Low 0 0 = Factory set calibration. Trim value until output = 1V, or 2mA
User calibration UCAL User calibration enable Yes/no
pt1.L Low calibration point for Input 1 The factory calibration point at which the low point offset was performed.
pt1.H High calibration point for Input 1 The factory calibration point at which the high point offset was performed.
OF1.L Offset Low for Input 1 Calculated offset, in display units.
OF1.H Offset High for Input 1 Calculated offset, in display units.
pt2.L Low calibration point for Input 2 The factory calibration point at which the low point offset was performed.
pt2.H High calibration point for Input 2 The factory calibration point at which the high point offset was performed.
OF2.L Offset Low for Input 2 Calculated offset, in display units.
OF2.H Offset High for Input 2 Calculated offset, in display units.
Name Description Values Meaning
PASSPASSPASSPASS Password configuration
ACC.P FuLL or Edit level password
cnF.P Configuration level password
Note:- When passwords are changed please make a note of the new numbers
ExitExitExitExit Exit configuration no/YES
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-23
CONFIGURATION EXAMPLES
Transducer Power Supply To configure the choice of output voltage:-
Do This The Display You Should See
Additional Notes
1. Press as many times as necessary to select the slot position in which the transducer power supply is fitted
The transducer power supply can be fitted in slot positions 1 and 2.
The display will show 1A or 1b accordingly
2. Press to read the identity of the module
This is read only where:
SG.SU = Transducer Power Supply
3. Press (twice) to read ‘Sens’
4. Press and to select ‘inv’ or ‘nor’
inv = 10Vdc nor = 5Vdc
The Transducer Power supply uses existing software written for digital modules. A list of parameters follow which are not applicable to this module.
1A
ConF
id
SG.SU
SEnS
inv
Configuration Installation and Operation Handbook
6-24 2408 and 2404 Controller
DeviceNet To configure Function, Baud Rate, Resolution and Node Address:-
Do This The Display You Should See
Additional Notes
1. Press as many times as necessary to select ‘HA’
This is the position in which the DeviceNet module is fitted
2. Press to read ‘id’ If the module is present
id = ‘cms’ (digital communications) or ‘none’ if the module is not present
3. Press to read ‘Func’
If the DeviceNet module is fitted ‘Func’ = ‘dnEt’ and will be read only
4. Press to read ‘bAud’
5. Press and to select the baud rate
Baud rate can be set to 125(K), 250(K) or 500(K)
6. Press to read ‘rES’
7. Press and to select ‘FuLL’ or ‘int’
FuLL — the decimal point position is implied, eg 100.1 is transmitted as 1001.
‘int’ — rounded to the nearest integer value
HA
ConF
id
cms
Func
dnEt
bAud
500
res
FuLL
Installation and Operation Handbook Configuration
2408 and 2404 Controller 6-25
Node Address is set up in Operator or Full Access level. Select either of these levels, then:-
8. Press as many times as necessary to select ‘cms’
9. Press to read ‘Addr’
10. Press and to select the address
Valid addresses are from 0 — 63
11. Press to read ‘nw.St’
Indicates the network status:-
‘run’ = network connected and operational
‘rdy’ = network connected but not operational
‘OFF.L’ = network not connected
cms
List
Addr
5
nw.St
run
Configuration Installation and Operation Handbook
6-26 2408 and 2404 Controller
Installation and Operation Handbook User Calibration
2408 and 2404 Controller 7-1
Chapter 7 USER CALIBRATION
This chapter has five topics:
• WHAT IS THE PURPOSE OF USER CALIBRATION?
• USER CALIBRATION ENABLE
• OFFSET CALIBRATION
• TWO POINT CALIBRATION
• CALIBRATION POINTS AND CALIBRATION OFFSETS To understand how to select and change parameters in this chapter you will need to have read Chapter 2 — Operation, Chapter 3- Access Levels and Chapter 6 — Configuration. WHAT IS THE PURPOSE OF USER CALIBRATION?
The basic calibration of the controller is highly stable and set for life. User calibration allows you to offset the ‘permanent’ factory calibration to either:
1. Calibrate the controller to the your reference standards.
2. Match the calibration of the controller to that of a particular transducer or sensor input.
3. Calibrate the controller to suit the characteristics of a particular installation.
4. Remove long term drift in the factory set calibration.
User calibration works by introducing a single point, or two-point, offset onto the factory set calibration.
User Calibration Installation and Operation Handbook
7-2 2408 and 2404 Controller
USER CALIBRATION ENABLE
The User calibration facility must first be enabled in configuration level by setting the parameter ‘UCAL’ in the input conf list to ‘YES’. This will make the User calibration parameters visible in Operator ‘FuLL’ level. Select configuration level as shown in Chapter 6, Configuration.
+
The Calibration Configuration List
Press until you reach the ‘CAL-Conf’ list.
Press until you reach ‘UCAL’.
User Calibration Enable
Use or to select:
• YES: Calibration enable • no: Calibration disabled
Press and together to go to the Exit display.
Exit configuration
Use or to select ‘YES’ to return to Operator level.
CAL
UCAL
no
Installation and Operation Handbook User Calibration
2408 and 2404 Controller 7-3
OFFSET CALIBRATION
Offset calibration is used to apply a single fixed offset over the full display range of the controller.
To calibrate, proceed as follows:
1. Connect the input of the controller to the source device to which you wish to calibrate.
2. Set the source to the desired calibration value.
3. The controller will display the current measurement of the value.
4. If the displayed value is correct, then the controller is correctly calibrated and no further action is necessary. If it is incorrect, then follow the steps shown below.
Select ‘FuLL’ access level, as described in Chapter 3.
x 3
Input list header
Press until you reach the input list header.
Press until you reach the ‘CAL’ display.
Calibration type
• FACt: Factory Calibration • USEr: User Calibration
Use or to select ‘FACt’.
Selecting ‘FACt’ reinstates the factory calibration and allows the application of a single fixed offset.
Press
continued on the next page
Displayed Value
Input
Factory Calibration
Fixed Offset
CAL
FACt
User Calibration Installation and Operation Handbook
7-4 2408 and 2404 Controller
Set Offset 1
Use or to set the offset value of Process Value 1 (PV1). The offset value is in display units.
Press
Set Offset 2
Use or to set the offset value of Process Value 2 (PV2), if configured. The offset value is in display units.
Press The table below shows the parameters which appear after ‘OFS.2’. These are all read only values and are for information.
Press to step through them.
mV.1 IP1 measured value (at terminals)
mV.2 IP2 measured value (at terminals), if DC input in Module 3 position
CJC.1 IP1 Cold Junction Compensation
CJC.2 IP2 Cold Junction Compensation
Li.1 IP1 Linearised Value
Li.2 IP2 Linearised Value
PV.SL Shows the currently selected input
If you do not want to look at these parameters, then press and this returns you to the ‘iP-LiSt’ header.
To protect the calibration against unauthorised adjustment, return to Operator level and make sure that the calibration parameters are hidden. Parameters are hidden using the ‘Edit’ facility described in Chapter 3, Access Levels.
OFS.2
0
See table on the right for additional
parameters.
OFS.1
0
Installation and Operation Handbook User Calibration
2408 and 2404 Controller 7-5
TWO-POINT CALIBRATION
The previous section described how to apply a offset, or trim, calibration, which applies a fixed offset over the full display range of the controller. A two-point calibration is used to calibrate the controller at two points and applies a straight line between them. Any readings above, or below, the two calibration points will be an extension of this straight line. For this reason it is best to calibrate with the two points as far apart as possible.
Proceed as follows:
1. Decide upon the low and high points at which you wish to calibrate.
2. Perform a two point calibration in the manner described below.
x 3
Input list header
Press until you reach the input list header, ‘ip LiSt’.
Press until you reach the ‘CAL’ display.
Calibration type • FACt: Factory Calibration • USEr: User Calibration
Use or to select ‘USEr’.
Selecting ‘USEr’ enables two-point calibration. [If two-point calibration is unsatisfactory, select ‘FACt’ to return to the factory set calibration.]
Press
CAL
FACt
Displayed Value
Input
x
x
Factory Calibration
High-point calibration
Low-point calibration
Calibration high-point value
Calibration low-point value
Offset introduced
Offset introduced
User Calibration
User Calibration Installation and Operation Handbook
7-6 2408 and 2404 Controller
Select Low-point Calibration This is the Calibration Status display. This display shows that no input is selected for calibration. • nonE: No selection • ip1.L: Input 1 (PV1) calibration low-point selected • ip1.H: Input 1 (PV1) calibration high-point selected • ip2.L: Input 2 (PV2) calibration low-point selected • ip2.H: Input 2 (PV2) calibration high-point selected
Use / to select the parameter for the Low Calibration point of Input 1, ‘ip1.L’.
Press
Adjust low-point calibration
This is the display for adjusting the Low Calibration point of Input 1. The lower readout is a live reading of the process value, which changes as the input changes. Make sure that the calibration source is connected to the terminals of Input 1, switched on and feeding a signal to the controller. It should be set to the desired low-point calibration value. If the lower readout does not show this value, then use
/ to adjust the reading to the required value.
Press to return to the ‘ip-List’ header. To perform the High-point Calibration, repeat the above procedure, selecting ‘ip1.H’ in the ‘CAL.S’ display for adjustment.
Press three times.
Calibration type ‘USEr’ was selected for the Low-point Calibration, and has remained selected.
Press
CAL.S
nonE
CAL
USEr
Adj
25
x 3
Installation and Operation Handbook User Calibration
2408 and 2404 Controller 7-7
Select High-point Calibration
This is the Calibration Status display, again. Use / to select the parameter for the High-point Calibration of Input 1, ‘ip1.H’.
Press
Adjust High-point Calibration
This is the display for adjusting the High Calibration point of Input 1. The lower readout is a live reading of the process value, which changes as the input changes.
Feed the desired high-point calibration signal to the controller, from the calibration source. If the lower readout does not show this value, then use / to adjust the reading to the required value.
Press to return to the ‘ip-List’ header. To protect the calibration against unauthorised adjustment return to Operator level and make sure that the calibration parameters are hidden. Parameters are hidden using the ‘Edit’ facility described in Chapter 3. To perform a User Calibration on Input 2, proceed as with Input 1 above, except that when ‘CAL.S-nonE’ appears, press
/ until ‘CAL.S-iP2.L’ is obtained, then proceed as with Input 1. Repeat the procedure for ‘iP2.H’.
Adj
1200
CAL
ip1.L
User Calibration Installation and Operation Handbook
7-8 2408 and 2404 Controller
CALIBRATION POINTS AND CALIBRATION OFFSETS If you wish to see the points at which the User calibration was performed and the value of the offsets introduced, then these are shown in Configuration, in ‘CAL-Conf’. The parameters are:
Name Parameter description Meaning
pt1.L Low calibration point for Input 1 The factory calibration point at which the low point offset was performed.
pt1.H High calibration point for Input 1 The factory calibration point at which the high point offset was performed.
OF1.L Offset Low for Input 1 Calculated offset, in display units.
OF1.H Offset High for Input 1 Calculated offset, in display units.
pt2.L Low calibration point for Input 2 The factory calibration point at which the low point offset was performed.
pt2.H High calibration point for Input 2 The factory calibration point at which the high point offset was performed.
OF2.L Offset Low for Input 2 Calculated offset, in display units.
OF2.H Offset High for Input 2 Calculated offset, in display units.
Note: The value of each of the parameters in the above table may also be altered by using the / buttons.
Installation and Operation Handbook Understanding The Ordering Code
2408 and 2404 Controller A-1
Appendix A
UNDERSTANDING THE ORDERING CODE
The 2408 and 2404 controllers have a modular hardware construction, which accepts up to three plug-in Input/Output modules and two communications modules to satisfy a wide range of control requirements. Two digital inputs and an optional alarm relay form part of the fixed hardware build. The ordering code is in two parts. The hardware coding and an optional configuration coding. The hardware coding specifies the basic build of the controller and the plug-in modules that are fitted. Part 1:
Hardware coding
Part 2: Configuration
Basic build
2408 2404
Model Module Comms 1 Display number 1 units Function Module Comms 2 Supply 2 Sensor Logic voltage Module Manual input 1 3 Alarm Range Logic relay min input 2 Range max Options
The controller may have been ordered with just the hardware build specified, or with configuration included. This is indicated by the ordering code on the side of the controller.
Plug-in modules
Plug-in I/O modules
Understanding the Ordering Code Installation and Operation Handbook
A-2 2408 and 2404 Controller
Part 1A: Hardware coding Basic build Plug-in modules
Model number Function Supply voltage Module 1
2408 CC VH LH
Function Standard PID control CC Controller CG 1 x 8 seg prog CP 1 x 16 seg prog P4 4 x 16 seg prog CM 20 x 16 seg prog Note 1 On/Off control NF Controller only NG 1 x 8 seg prog NP 1 x 16 seg prog N4 4 x 16 seg prog NM 20 x 16 seg prog Motorised valve control VC Valve positioner (VP) VG 1 x 8 seg prog VP 1 x 16 seg prog V4 4 x 16 seg prog VM 20 x 16 seg prog Note 1
Supply voltage VH 85 to 264Vac VL 20 to 29Vac/dc
Module 1 XX Not fitted Relay: 2-pin R2 Fitted unconfigured RH PID heating RU Valve raise output Relay: change-over R4 Fitted unconfigured YH PID heating RP Valve raise (note 6) Or Alarm 1: select from table A Logic: (Non-isolated) L2 Fitted unconfigured LH Heating output M1 PDS heater break detect
(note 2) M2 PDS current monitoring
(note3) Logic: (isolated) LO Single logic output Triac T2 Fitted unconfigured TH Heating output TU Valve raise output DC control (isolated) D4 Fitted unconfigured H6 0-20mA PID heating H7 4-20mA PID heating H8 0-5V PID heating H9 1-5V PID heating HZ 0-10V PID heating Digital I/O (unconfigured) TK Triple contact input TL Triple logic input TP Triple logic output Dual relay RR Fitted unconfigured RD PID heat + PID cool RM Valve raise and lower Dual triac TT Fitted unconfigured TD PID heat + PID cool TM Valve raise and lower Logic + relay LR Fitted unconfigured LD PID heat + PID cool QC Mode 2 + cool Logic + triac LT Fitted unconfigured GD PID heat + PID cool QD Mode 2 + cool Transducer P5 G3 5Vdc G5 10Vdc
Table A : Alarm relay functions
FH High alarm FL Low alarm DB Deviation band DL Low dev. alarm DH High dev alarm
Continued next page
Model Number 2408 1/8 DIN Controller 2404 1/4 DIN Controller Profibus units 2408f 1/8 DIN Controller 2404f 1/4 DIN Controller
Table B : DC retransmission
D6 Fitted unconfigured First character V- PV retrans S- Setpoint retrans O- Output retrans Z- Error retrans Second character -1 0-20mA -2 4-20mA -3 0-5V -4 1-5V -5 0-10V
Installation and Operation Handbook Understanding The Ordering Code
2408 and 2404 Controller A-3
Part 1B: Hardware coding Plug-in modules Plug-in modules
continued Module 2
Module 3
Alarm relay
Comms 1
Comms 2
Manual
RC FL FH YM TS ENG
Module 2 XX Not fitted Relay: 2-pin R2 Fitted unconfigured RC Cooling output RW Valve lower output Relay: change-over R4 Fitted unconfigured YC Cooling Output RL Valve lower (note 6) PO Program event output 1 (note 7) PE Program END segment Or Alarm 2: select from table A Dual relay RR Fitted unconfigured PP Program events 1 & 2
(note 7) Logic (non-isolated) L2 Fitted unconfigured LC PID cooling Logic (isolated) LO Single logic output Triac T2 Fitted unconfigured TC PID cooling TW Valve lower output DC control isolated D4 Fitted unconfigured C6 0-20mA PID cooling C7 4-20mA PID cooling C8 0-5V PID cooling C9 1-5V PID cooling CZ 0-10V PID cooling Digital I/O (unconfigured) TK Triple contact input TL Triple logic input TP Triple logic output Power supply MS 24Vdc transmitter DC retran (isolated) Selct from table B Potentiometer input VU Fitted unconfigured VS Valve position feedback VR Setpoint input Transducer PSU G3 5Vdc G5 10Vdc
Comms 1 XX None 2-wire EIA-485 Y2 Fitted unconfigured YM Modbus protocol YE EI Bisynch protocol
(note 1) RS-232 A2 Fitted unconfigured AM Modbus protocol AE EI Bisynch protocol
(note 1) 4-wire RS-485 F2 Fitted unconfigured FM Modbus protocol FE EI Bisynch protocol
(note 1) PDS output M7 Fitted unconfigured PT PV retransmission TS Setpoint retrans OT Output retrans Profibus module PB High speed RS485 DeviceNet DN DeviceNet
Comms 2
XX Not fitted PDS input M6 Fitted unconfigured RS Setpoint input PDS output M7 Fitted unconfigured PT PV retransmission TS Setpoint retrans OT Output retrans
Module 3 XX Not fitted Relay: 2-pin R2 Fitted unconfigured Relay: change-over R4 Fitted unconfigured PO Program event 4 (note
7) PE Program END output Or Alarm 3 select from table A Logic (non-isolated) L2 Fitted unconfigured Logic (isolated) LO Single logic output Triac T2 Fitted unconfigured Dual relay RR Fitted unconfigured
PP Program event 4 & 5 (note 7)
Digital I/O (unconfigured) TK Triple contact input TL Triple logic input TP Triple logic output Power supply MS 24V transmitter DC remote input D5 Fitted unconfigured W2 4 to 20mA setpoint W5 0 to 10V setpoint WP Second PV input DC retran (isolated) Select from table B Potentiometer input VU Fitted unconfigured VS VP feedback VR Setpoint input Transducer PSU G3 5Vdc G5 10Vdc
Manual XXX No manual ENG English FRA French GER German NED Dutch SPA Spanish SWE Swedish ITA Italian
Alarm relay XX Not fitted Alarm 4 relay RF Fitted unconfigured Table A alarm options plus: RA Rate of change PDS alarms LF Heater break detect HF Current monitor heater brk SF Current monitor SSR fail PO Program event 7 (note 7) PE Program END output
Understanding the Ordering Code Installation and Operation Handbook
A-4 2408 and 2404 Controller
—
Hardware Part 2: Configuration coding Sensor
input Range
min Range max
Display Units
Continued next page
K 0 1000 C
See note 4
Sensor input Range min &max Standard sensor inputs °C °F
J J thermocouple -210 to 1200 -340 to 2192 K K thermocouple -200 to 1372 -325 to 2500 T T thermocouple -200 to 400 -325 to 750 L L thermocouple -200 to 900 -325 to 650 N N thermocouple -250 to 1300 -418 to 2370 R Type R — Pt13%Ph/Pt -50 to 1768 -58 to 3200 S Type S — Pt10%Rh/Pt -50 to 1768 -58 to 3200 B Type B —
Pt30%Rh/Pt6%Rh 0 to 1820 32 to 3308
P Platinel II 0 to 1369 32 to 2496 Z RTD/PT100 -200 to 850 -325 to 1562 Process inputs F +/- 100mV 0 to 9999 Y 0-20 mA Linear 0 to 9999 A 4-20 mA Linear 0 to 9999 W 0-5V DC Linear 0 to 9999 G 1-5V DC Linear 0 to 9999 V 0-10V DC Linear 0 to 9999 Factory downloaded input C *Type C
W5%Re/W26%Re (Hoskins)*
0 to 2319 32 to 4200
D Type D — W3%Re/W25%Re
0 to 2399 32 to 4350
E E thermocouple -270 to 1000 -450 to 1830 1 Ni/Ni18%Mo 0 to 1399 32 to 2550 2 Pt20%Rh/Pt40%Rh 0 to 1870 32 to 3398 3 W/W26%Re
(Englehard) 0 to 2000 32 to 3632
4 W/W26%Re (Hoskins)
0 to 2010 32 to 3650
5 W5%Re/W26%Re (Englehard)
10 to 2300 50 to 4172
6 W5%Re/W26%Re (Bucose)
0 to 2000 32 to 3632
7 Pt10%Rh/Pt40%Rh 200 to 1800 392 to 3272 8 Exergen K80 I.R.
pyrometer -45 to 650 -50 to 1200
Display Units C Celcius F Fahrenheit K Kelvin X Linear input
Installation and Operation Handbook Understanding The Ordering Code
2408 and 2404 Controller A-5
Part 2: Configuration continued Digital
input 1 Digital input 2
Control Power feedback
Cooling Buttons Program
AM S2 XX XX XX MD XX
The example given in the coding is for 2408 PID controller, 85 to 264 Vac, logic heating, relay cooling, low alarm relay, high alarm relay, RS485 Modbus comms, PDSIO setpoint retransmission, type K thermocouple, 0 to 1000oC, Auto/manual select, second setpoint select, manual button disabled.
Digital inputs 1 & 2 XX Disabled AT Adaptive tune enable AM Manual select FA Select full access level SR Remote setpoint
select RB Simulates UP button
S2 Second setpoint select
LB Simulates DOWN button
EH Integral hold SB Simulates SCROLL button
AC Alarm acknowledge PB Simulates PAGE button RP Setpoint rate limit
enable B1 Least sig. BCD dig.
RN Run program B2 2nd BCD digit HO Hold program B3 3rd BCD digit RE Reset program B4 4th BCD digit RH Run/hold program B5 5th BCD digit KL Keylock B6 Most sig. BCD digit NT Run/Reset program SY Standby — ALL ops OFF TN Reset/Run program SG Skip segment (without
changing SP) HB Prog. holdback
enable SC Program synch.
P2 PID2 select PV Select PV2 ST One-shot tune enable AG Advance to end of
segment (& step to target setpoint)
M5 CTX (mode 5) (input 2 only)
Options Control action XX Reverse acting (standard) DP Direct acting PID control Power feedback XX Enabled on logic, relay &
triac heating PD Feedback disabled Cooling options XX Linear cooling CF Fan cooling CW Water cooling CL Oil cooling CO On/off cooling Front panel buttons XX Enabled MD Auto/man button disabled MR Auto/man & run/hold
disabled RD Run/hold button disabled Programmer time units XX Dwell & ramp in minutes HD Dwell time in hours HR Ramp rate in units/hour
Understanding the Ordering Code Installation and Operation Handbook
A-6 2408 and 2404 Controller
Notes:
1. Not available with profibus controllers
2. PDS heater break detect will transmit the power demand to a TE10S solid state relay and read back a heater break alarm
3. PDS current monitoring will transmit the power demand signal to a TE10S solid state relay and read back load current and open and short circuit alarms
4. Setpoint limits: include the decimal position required in the displayed value. Up to one for temperature inputs, up to two for process inputs
5. An external 1% current sense resistor is supplied as standard. If greater accuracy is required, a 0.1% 2.49Ω can be ordered as part number SUB2K/249R.1
6. Only available with Profibus controller
7. Not available with 8 segment programmer
• PDS is a proprietary technique for bi-directional transmission of analogue and digital
data between instruments. Mode 1: provides logic heating to a TE10S (fitted with option PDS1) solid state relay with feedback of a general load fault alarm. Mode 2: provides logic heating to a TE10S (fitted with option PDS2) solid state relay with feedback of load current and two alarms: solid state relay failure and heater circuit failure.
• Range min and Range max: Thermocouple and RTD sensor inputs will always display over the full operating range shown in Sensor input table. For these inputs, the values entered here are the low and high setpoint limits. For process inputs, the values are the display scaling. corresponding to the minimum and maximum input values.
Installation and Operation Handbook Safety Information
2408 and 2404 Controller B-1
SAFETY and EMC INFORMATION
Please read this section carefully before installing the controller
This controller is intended for industrial temperature and process control applications when it will meet the requirements of the European Directives on Safety and EMC. Use in other applications, or failure to observe the installation instructions of this handbook may impair the safety or EMC protection provided by the controller. It is the responsibility of the installer to ensure the safety and EMC of any particular installation.
Safety
This controller complies with the European Low Voltage Directive 73/23/EEC, amended by 93/68/EEC, by the application of the safety standard EN 61010.
Electromagnetic compatibility
This controller conforms with the essential protection requirements of the EMC Directive 89/336/EEC, amended by 93/68/EEC, by the application of a Technical Construction File. This instrument satisfies the general requirements of an industrial environment as described by EN 50081-2 and EN 50082-2. For more information on product compliance refer to the Technical Construction File. SERVICE AND REPAIR
This controller has no user serviceable parts. Contact your nearest Eurotherm Controls agent for repair.
Caution: Charged capacitors
Before removing an instrument from its sleeve, disconnect the supply and wait at least two minutes to allow capacitors to discharge. Failure to observe this precaution will expose capacitors that may be charged with hazardous voltages. In any case, avoid touching the exposed electronics of an instrument when withdrawing it from the sleeve.
Electrostatic discharge precautions
When the controller is removed from its sleeve, some of the exposed electronic components are vulnerable to damage by electrostatic discharge from someone handling the controller. To avoid this, before handling the unplugged controller discharge yourself to ground.
Cleaning
Do not use water or water based products to clean labels or they will become illegible. Isopropyl alcohol may be used to clean labels. A mild soap solution may be used to clean other exterior surfaces of the product.
Safety Information Installation and Operation Handbook
B-2 2408 and 2404 Controller
INSTALLATION SAFETY REQUIREMENTS
Safety Symbols
Various symbols are used on the instrument, they have the following meaning:
Caution, (refer to the accompanying documents)
Functional earth (ground) terminal!
The functional earth connection is not required for safety purposes but to ground RFI filters.
Personnel
Installation must only be carried out by qualified personnel.
Enclosure of live parts
To prevent hands or metal tools touching parts that may be electrically live, the controller must be installed in an enclosure.
Caution: Live sensors
The fixed digital inputs, non-isolated dc, logic and PDSIO outputs and the logic output of dual output modules, are all electrically connected to the main process variable input. If the temperature sensor is connected directly to an electrical heating element then these non-isolated inputs and outputs will also be live. The controller is designed to operate under these conditions. However you must ensure that this will not damage other equipment connected to these inputs and outputs and that service personnel do not touch connections to these i/o while they are live. With a live sensor, all cables, connectors and switches for connecting the sensor and non-isolated inputs and outputs must be mains rated.
Wiring
It is important to connect the controller in accordance with the wiring data given in this handbook. Take particular care not to connect AC supplies to the low voltage sensor input or other low level inputs and outputs. Only use copper conductors for connections (except thermocouple inputs) and ensure that the wiring of installations comply with all local wiring regulations. For example in the in the UK use the latest version of the IEE wiring regulations, (BS7671). In the USA use NEC Class 1 wiring methods.
Power Isolation
The installation must include a power isolating switch or circuit breaker. This device should be in close proximity to the controller, within easy reach of the operator and marked as the disconnecting device for the instrument.
Earth leakage current
Due to RFI Filtering there is an earth leakage current of less than 0.5mA. This may affect the design of an installation of multiple controllers protected by Residual Current Device, (RCD) or Ground Fault Detector, (GFD) type circuit breakers.
Installation and Operation Handbook Safety Information
2408 and 2404 Controller B-3
Overcurrent protection
To protect the internal PCB tracking within the controller against excess currents, the AC power supply to the controller and power outputs must be wired through the fuse or circuit breaker specified in the technical specification. Voltage rating
The maximum continuous voltage applied between any of the following terminals must not exceed 264Vac:
• line or neutral to any other connection;
• relay or triac output to logic, dc or sensor connections;
• any connection to ground.
The controller should not be wired to a three phase supply with an unearthed star connection. Under fault conditions such a supply could rise above 264Vac with respect to ground and the product would not be safe.
Voltage transients across the power supply connections, and between the power supply and ground, must not exceed 2.5kV. Where occasional voltage transients over 2.5kV are expected or measured, the power installation to both the instrument supply and load circuits should include a transient limiting device.
These units will typically include gas discharge tubes and metal oxide varistors that limit and control voltage transients on the supply line due to lightning strikes or inductive load switching. Devices are available in a range of energy ratings and should be selected to suit conditions at the installation.
Conductive pollution
Electrically conductive pollution must be excluded from the cabinet in which the controller is mounted. For example, carbon dust is a form of electrically conductive pollution. To secure a suitable atmosphere in conditions of conductive pollution, fit an air filter to the air intake of the cabinet. Where condensation is likely, for example at low temperatures, include a thermostatically controlled heater in the cabinet.
Over-temperature protection
When designing any control system it is essential to consider what will happen if any part of the system should fail. In temperature control applications the primary danger is that the heating will remain constantly on. Apart from spoiling the product, this could damage any process machinery being controlled, or even cause a fire.
Reasons why the heating might remain constantly on include:
• the temperature sensor becoming detached from the process;
• thermocouple wiring becoming short circuit;
• the controller failing with its heating output constantly on;
• an external valve or contactor sticking in the heating condition;
• the controller setpoint set too high.
Where damage or injury is possible, we recommend fitting a separate over-temperature protection unit, with an independent temperature sensor, which will isolate the heating circuit.
Safety Information Installation and Operation Handbook
B-4 2408 and 2404 Controller
Please note that the alarm relays within the controller will not give protection under all failure conditions.
Grounding of the temperature sensor shield
In some installations it is common practice to replace the temperature sensor while the controller is still powered up. Under these conditions, as additional protection against electric shock, we recommend that the shield of the temperature sensor is grounded. Do not rely on grounding through the framework of the machine.
INSTALLATION REQUIREMENTS FOR EMC
To ensure compliance with the European EMC directive certain installation precautions are necessary as follows:
• For general guidance refer to Eurotherm Controls EMC Installation Guide, HA025464.
• When using relay or triac outputs it may be necessary to fit a filter suitable for suppressing the emissions. The filter requirements will depend on the type of load. For typical applications we recommend Schaffner FN321 or FN612.
• If the unit is used in table top equipment which is plugged into a standard power socket, then it is likely that compliance to the commercial and light industrial emissions standard is required. In this case to meet the conducted emissions requirement, a suitable mains filter should be installed. We recommend Schaffner types FN321 and FN612.
Routing of wires
To minimise the pick-up of electrical noise, the wiring for low voltage dc and particularly the sensor input should be routed away from high-current power cables. Where it is impractical to do this, use shielded cables with the shield grounded at both ends.
Installation and Operation Handbook Technical Specification
2408 and 2404 Controller C-1
TECHNICAL SPECIFICATION
Main Process Value Input and Second DC Input Low level range +100mV High level range 0 to 10Vdc or 0-20mA with external 2.49Ω current shunt. All
configurable between limits Sample Rate 9Hz (110mS) Resolution <2µV for low level range, <0.2mV for high level range Linearity Better than 0.2oC Calibration accuracy The greater of 0.25% of reading or + 1oC or +1LSD User calibration Low and high offsets can be applied Input filter Off to 999.9 secs Thermocouple types Refer to the ordering code sensor input table Cold junction compensation
>30 to 1 rejection of ambient temperature changes in automatic mode. Uses INSTANT ACCURACYTM cold junction sensing technology to eliminate warm up drift and to respond quickly to ambient temperature changes. External references 0, 45, and 50oC
RTD/PT100 input 3-wire, Pt100 DIN43750. Bulb current 0.3mA. Up to 22Ω in each lead without error
Potentiometer input 100 to 15Kohm Analogue input functions
Process value, remote setpoint, setpoint trim, external power limit, feedforward input,, valve position feedback
Second process value input functions
Select min, select max, derived value, transfer to 2nd PV
Digital inputs Isolated except for fixed digital inputs 1 & 2 Contact closure inputs
Open circuit voltage: 24 to 30 Vdc Short circuit current: 24 to 29mA Off state: < 100 ohms input resistance On state: > 28Kohm input resistance
Logic inputs (current sinking)
Off state: -3 to 5Vdc @ <-0.4mA On state: 10.8 to 30Vdc @ 2.5mA
Digital input functions
Refer to the ordering code
Digital Outputs Relay rating Min: 12V, 100mAdc. Max:2A, 264Vac resistive Single logic output 18Vdc, 20mA. This output is not isolated from the main process
value input Triple logic output 12Vdc, 8mA per channel (isolated) Digital o/p functions As per the ordering code High current output 10Amp, 264Vac resistive. This option is not available on controller
from Jan-04 Triac rating 1A, 30 to 264Vac resistive (isolated) Analogue outputs
Technical Specification Installation and Operation Handbook
C-2 2408 and 2404 Controller
Range Scaleable between 0-20mA and 0-10Vdc (isolated) Resolution 1 part in 10,000 for analogue retransmission Analogue output functions
Refer to ordering code
Transmitter supply Rating 20mA, 24Vdc Control functions Control modes On/Off, PID, or motorised valve control, with or without feedback
potentiometer Cooling algorithms Linear, water (non-linear), fan (min on time), oil Tuning One shot (automatic tune of PID and overshoot inhibition
parameters) and continuous adaptive tuning Number of PID sets Two Auto/manual control Bumpless transfer or forced manual output available Setpoint rate limit Display units per second, minutes or hour Alarms Number of alarms Four Alarm types Absolute high or low. Deviation band, deviation high, deviation
low. Rate of change Alarm modes Latching or non-latching. Blocking. Energised or de-energised in
alarm Setpoint programming Number of programs 1, 4 or 20 Segments per program
16
Event outputs Up to eight Communications (all modules are isolated) Profibus High speed, RS485. Up to 1.5Mb/s Modbus ® RS232,2-wire,RS 485 and 4 wire RS485 modules Baud rate 1200, 2400, 4800, 9600 and 19,200 baud PDS Slave input (isolated) Remote setpoint input with holdback to master Master output Isolated from main PV. Retransmission of setpoint, process value
or output
Installation and Operation Handbook Technical Specification
2408 and 2404 Controller C-3
General Display Dual, 4 digit x 7 segment LED. Up to two decimal places Supply 85 to 264Vac, 48 to 62 Hz, 10 W max OR
24Vdc or ac -15%, +20%. 10W max Operating ambient 0 to 55oC and 5 to 90% RH non-condensing Storage temperature -10 to +70oC Panel sealing IP65 Dimensions 2408: 48mm wide x 96mm high x 150mm deep
2404: 96mm wide x 96mm high x 150mm deep Weight 250g EMC standards EN61326-1 generic standards for industrial environments Safety standards Meets EN61010, installation category II (voltage transients must not
exceed 2.5kV), pollution degree 2 Atmospheres Not suitable for use above 2000m or in explosive or corrosive
atmospheres. Electrically conductive pollution must be excluded from the cabinet in which this controller is mounted
Technical Specification Installation and Operation Handbook
C-4 2408 and 2404 Controller
Installation and Operation Handbook Load Current Monitoring and Diagnostics
2408 and 2404 Controller D-1
Appendix D LOAD CURRENT MONITORING AND DIAGNOSTICS
Current flowing in a system of electrical heating elements (the ‘Load’) can be displayed on the controller by using a Eurotherm TE10 SSR fitted with intelligent current transformer, PDCTX, or an SSR or contactor with an external PDCTX. Load current monitoring and diagnostics may be used with any time proportioned output, fitted in module position 1A, and uses the logic output wires which drive the SSR to return signals back to the controller These signals represent the RMS value of the load current during the ON period, or load related alarm conditions. It is not designed for analogue outputs i.e. phase angle control. It is also designed for single phase operation only. There are three modes of operation:-
1. Mode 1 Detects if there is a break in the heater circuit. This includes heater or SSR open circuit. A single Load Failure alarm message is displayed on the lower readout of the controller.
2. Mode 2 Provides the following:-
Display of true RMS load current On the lower readout of the controller
Displays the true RMS current in the ON state to the load.
Low current alarm Analogous to Partial Load Failure (PLF) supplied in some Eurotherm SSRs
Provides advanced warning of failure of one or more heaters in parallel
High current alarm Activated when the heater exceeds a set limit
Typically used where element bunching may occur
SSR short circuit This will apply full power to the heaters which could result in an over temperature condition. This alarm provides early warning.
Heater failure Indicates open circuit load conditions
3. Mode 5 Provides the same features as mode 2 with two additional alarms. This mode is for use with contactors or other devices which do not use the PDS logic output from the controller as the drive signal. For example, a time proportioning logic, relay or triac output to operate a contactor. Mode 5, therefore, requires an additional input to the controller to display the load conditions. It uses the LB digital input terminals for this, as shown in Figure D.2.
Current Transformer Open Circuit Alarm is shown if the PDS connection to PDCTX or SSR become disconnected
Current Transformer Short Circuit Alarm is shown if the PDS connection from PDCTX or SSR are short circuited
Load Current Monitoring and Diagnostics Installation and Operation Handbook
D-2 2408 and 2404 Controller
1.
EXAMPLE WIRING DIAGRAM (FOR MODE 1 & 2 OPERATION)
Hardware Required 1. Eurotherm SSR type TE10/PDS2 OR 2. Eurotherm intelligent current transformer type PD/CTX + contactor or zero voltage
switching SSR 2408 or 2404 controller configured for PDS mode 2 option using logic output. This module must be fitted in module position 1. (order code M2).
Figure D.1 Connections for Mode 1 & 2
WARNING!
Take care that the controller is correctly wired for the mode of operation which is configured. Failure to do so may be hazardous in some situations.
Heater
Heater power fuse
(load dependent)
L N Controller Fuse 2A(T)
N
L
V+
V-
1B
1A M O D U L E 1
C O M M S 1
+ —
+ PV —
C O M M S 2
Alternative current regulator arrangements:-
The Eurotherm TE10/PDS2 contains
integral power regulator and intelligent PDCTX
The PDCTX can be supplied separately for use with any SSR or logic thyristor unit as
shown in the diagram below. The output drive capability of the PDCTX is
5V at 7mA maximum
PDCTX Intelligent Current Transformer
Logic input SSR
+
+ —
—
To Heater
To L To logic output 1A & 1B
TE10 Solid State Relay
T/C
+ —
L N
This represents a single turn through the CT
Installation and Operation Handbook Load Current Monitoring and Diagnostics
2408 and 2404 Controller D-3
EXAMPLE WIRING DIAGRAM (FOR MODE 5 OPERATION)
Hardware Required 1. Eurotherm intelligent current transformer type PD/CTX + contactor 2. 2408 or 2404 controller configured for PDS mode 5 option using logic, relay or triac
output. This module must be fitted in module position 1. Digital input LB (order code M5) must be configured to accept PDCTX input as described in the configuration section of this appendix.
The controller will have the order code M5 in the Logic Input position.
Figure D.2 Example Wiring Connections For Contactor Operation (mode 5) WARNING!
Take care that the controller is correctly wired for the mode of operation which is configured. Failure to do so may be hazardous in some situations.
Contactor + PDCTX mode 5
+ —
Contactor
Heater power fuse (load dependent)
L N
Controller Fuse 2A(T)
N
V+
V-
1B
1A M O D U L E 1
C O M M S 1
+ PV —
C O M M S 2
Heater
T/C
LB
LC
Load Current Monitoring and Diagnostics Installation and Operation Handbook
D-4 2408 and 2404 Controller
OPERATION
To Read Load Current (modes 2 and 5 only)
Do This This Is The Display You Should See Additional Notes
From the ‘InFo’ list
Press until AmPS is shown in the upper display
It will revert to the HOME display after 45 seconds or 10 seconds if an alarm is present
To Display Load Current Continuously in the Lower Readout (modes 2 and 5 only)
Do This This Is The Display You Should See Additional Notes
From the ‘HOME’ display, Figure 1.4,
Press until diSP is shown in the upper display
Press or until AmPS is displayed in the lower display
Current will be displayed in the lower readout continuously when the controller reverts to the HOME display, see also ‘Display Modes’ below.
Display Modes
SSR RMS On State Current This is the default state when high or low current alarms are configured. The load current displayed is the steady state true rms current measured during the ON period. The minimum on times are:- Mode 2 0.1second Mode 5 3 seconds
Meter Mode Meter mode applies to mode 5 only. If low current alarms are not configured the current displayed is a filtered instantaneous RMS value. This behaves like a damped analogue meter. It may be used in applications where the current sensor is not linked to control, for example, telemetry, indication.
AmPS 5
AmPS
—-
diSP AmPS
Current will be displayed in the lower readout. See also ‘Display Modes’ below.
This display will be shown if: I. The controller is unable to resolve the reading II. The controller is obtaining a reading III. The measurement has timed out i.e. current has
not flowed for 15 seconds, in mode 2.
Installation and Operation Handbook Load Current Monitoring and Diagnostics
2408 and 2404 Controller D-5
How Heater Alarms Are Displayed
Do This This Is The Display You Should See Additional Notes
If an alarm is present it will flash a four character mnemonic in the lower display
If more than one alarm is active, the display will alternate between the alarm messages and the default parameter in the lower display
The Alarm Messages are:-
Mnemonic Meaning Description
The following two messages are alarms which are produced as a result of failure within the process. In place of dashes the alarm number will appear i.e 1, 2, 3, or 4
-LCr Alarm number — Low Current
Used for partial load failure detection. To avoid nuisance tripping due to supply voltage variations set to a value at least 15% below the minimum normal operating current
-HCr Alarm number — High Current
Used for load overcurrent protection. To avoid nuisance tripping due to supply voltage variations set to a value at least 15% above the maximum normal operating current.
Note: This alarm is not intended to provide instantaneous safety protection from short circuit fault conditions
The following message is a diagnostic alarm which appears for mode 1 operation only.
LdF Load Fail This includes failure of the heater circuit or the SSR
The following four messages are diagnostic alarms produced as a result of failure within the equipment or wiring connections. They appear for modes 2 and 5 operation only. They may be enabled using the diAG parameter in the AL LiSt, see ‘SHORT CIRCUIT SSR ALARM AND HEATER FAIL ALARM’
Htr.F Heater Fail No current is being drawn while the controller output demand signal is on
SSr.F SSR Fail The load is continuously on while the controller output demand signal is off
Ct.OP Current Transformer Open Circuit
Indicates that the PDS input is open circuit.
Mode 5 only
Ct.Sh Current Transformer Short Circuit
Indicates that the PDS input is short circuit
Mode 5 only
Actual Temperature (PV)
HOME Display
20.0 1LCr
OP1 OP2
Load Current Monitoring and Diagnostics Installation and Operation Handbook
D-6 2408 and 2404 Controller
TO SET THE ALARM TRIP LEVELS
Do This This Is The Display You Should See Additional Notes
From the HOME display
press until the AL LiStAL LiStAL LiStAL LiSt is displayed
Press button
until the desired alarm number is displayed
Press or to adjust the alarm trip level
To select the Alarm List header
To select the diagnostic alarm parameter found under the Alarm List header
The alarm trip level is set to 123
SHORT CIRCUIT SSR ALARM AND HEATER FAIL ALARM
These alarms exist as Diagnostic Alarms in the controller. To make the alarm active it is only necessary to turn on the diagnostic alarm feature in the Alarm List in the Operator Level
Do This This Is The Display You Should See Reason
From the HOME
display press button until the AL LiSt is displayed
Press until DiAG is displayed
Press or to select YES
This opens the list which contains the diAG mnemonic This activates the diAG mnemonic to allow Diagnostic Alarms to be displayed in the lower readout of the HOME display
RELAY OUTPUTS
The fixed relay output connected to terminals AA to AC in a 1/8 or 1/4 DIN controller is normally used for alarm purposes. In addition, any plug in module can be used for alarms provided they are not already being used for another purpose , such as control. Any one or more alarms can be attached to an output, which will operate when an alarm occurs. Contacts are rated at 2A 264Vac for operating external beacons or audible devices.
AL LiSt
DiAG YES
AL LiSt
1— 123
1 2 3 or 4 indicates the alarm number; — indicates the alarm type:- e.g. LCr or HCr
Installation and Operation Handbook Load Current Monitoring and Diagnostics
2408 and 2404 Controller D-7
TO CONFIGURE PDS LOAD CURRENT DIAGNOSTICS
Configuration of PDS load current diagnostics is in four parts:-
1. Configure the Logic Module for PDS Mode 1 or 2 operation. If the control device is a contactor or standard SSR, configure the LA digital input for mode 5 operation.
2. Configure the Low and High Current trip alarms. 3. Attach the alarms to operate an output relay. 4. Set up the Scaling Factor. First enter Configuration Level. See Chapter 5 TO CONFIGURE THE LOGIC MODULE FOR PDS MODES 1 OR 2
Do This This Is The Display You Should See Additional Notes
Press until the 1A Conf is displayed
Press to show id
Press to show Func
Press or to show SSr1 or SSr 2 as required.
Press to show VAL.L
Press or to show 0.0
This opens the configuration list associated with module position 1A
This shows the identity of the module
The module identity is logic output
This shows the function of module
The module function is set to PDS mode 1
This is the lower PID demand level
To set the minimum PID signal to 0%
VAL.L 0.0
1AConf
id Log
Func SSr1
Load Current Monitoring and Diagnostics Installation and Operation Handbook
D-8 2408 and 2404 Controller
Press to show VAL.H)
Press or to show 100.0
Press to show OUT.L
Press or to show 0.0
Press to show OUT.H
Press or
to show 100.0
Press to show SEnS
Press or to show nor
This is the upper PID demand level
To set the maximum PID signal to 100%
This is the minimum output power
To set the min output power to 0
This is the maximum output power
To set the max output power to 100
This sets the output signal to normal for heating control
VAL.H 100.0
SenSnor
OUT.L 0.0
OUT.H 100.0
Warning! If OUT.L is set to any figure other than 0 the minimum output power will be limited to this level. You must ensure that this does not present an unsafe condition for
Installation and Operation Handbook Load Current Monitoring and Diagnostics
2408 and 2404 Controller D-9
TO CONFIGURE LOGIC INPUT B FOR PDS (MODE 5 ONLY)
Do This This Is The Display You Should See Additional Notes
Press button
until the LB Conf
is displayed
Press to show id
Press to show Func
Press or to select AmPs
This identifies the LA input as logic and is read only To configure the input for the PDCTX.
The system is designed to operate in either mode 2 or mode 5 configuration only. Selecting both simultaneously will disable the output. However, mode 1 and mode 5 can be used together.
LB Conf
id LoG.i.i.i.i
FuncAmPs
Load Current Monitoring and Diagnostics Installation and Operation Handbook
D-10 2408 and 2404 Controller
TO CONFIGURE LOW AND HIGH CURRENT TRIP ALARMS
Alarm 1 will be configured as Load Current Low (Lcr) Alarm 2 will be configured as Load Current High (Hcr)
Do This This Is The Display You Should See Additional Notes
Press button
until the AL Conf
is displayed
This opens the configuration list which contains the Alarms
Press to show AL1 (alarm 1)
Press or to show LCr
Press until AL2 (alarm 2) appears
Press or to show HCr
To select alarm 1 To make alarm 1 = Low Current To select alarm 2. To make alarm 2 = High Current
Note:- The above alarms are known as SOFT ALARMS because they are indication only.
AL Conf
AL1 LCr
After 0.5 sec the display will blink to show the alarm type has been accepted
AL2 HCr
After 0.5 sec the display will blink to show the alarm type has been accepted
Installation and Operation Handbook Load Current Monitoring and Diagnostics
2408 and 2404 Controller D-11
TO ATTACH SOFT ALARMS TO A RELAY OUTPUT
Any one alarm indicated above may be attached to an output (normally a relay). Alternatively any combination of alarms may be attached to operate a relay using the procedure below:-
Do This This Is The Display You Should See Additional Notes
Press “PAGE” key
as many times as necessary to AA ConF
Press until 1— is displayed
Press or to select YES or Repeat the above step for every alarm to be attached to the output
To select the output which you want to operate when the alarm condition occurs. You may also choose 1A, 1B, 1C, 2A, 2B, 2C, 3A, 3B, 3C or 4A depending upon the controller and the number and type of modules fitted yes means that the selected output will activate when an alarm occurs in normal operation no means the output will not activate
aA Conf
1— yes
1—- denotes alarm 1 followed by three letters which denote the alarm type e.g. LCr
Alarms Connected to a Relay Output
dIG SEnS
nor
inv Output Module
Soft Alarms OR
AA
AB
Load Current Monitoring and Diagnostics Installation and Operation Handbook
D-12 2408 and 2404 Controller
THE SCALING FACTOR
The value of the current displayed on the controller is scaled using the scaling factor. This is found in the inSt ConF list. It is set, by default, to 100 and assumes a single turn through the current transformer. If two turns are made through the current transformer it will be necessary to adjust the scaling factor to 50 to obtain the same reading. Under normal conditions you should not need to change the scaling factor. If, however, you wish to change the sensitivity of the current reading, for example, to read very low currents you may need to change the number of turns through the PDCTX and/or adjust the scaling factor to compensate. See also note 1 below. TO ADJUST THE SCALING FACTOR
Do This This Is The Display You Should See Additional Notes
Press button
until inSt Conf is
displayed
Press until LC.Hi is displayed
Press or to change the scaling factor
Note 1:- Minimum Resolvable Current TE10 4A RMS. It is not possible to read currents lower than 4A when using a TE10. PDCTX 4A RMS for a single turn through the PDCTX Should you wish to read currents lower than 4A using a PDCTX it is necessary to increase the number of turns through the PDCTX and adjust the scaling factor to compensate. For example: To read 1.0A wind 4 turns through the PDCTX and adjust the scaling factor to 25 as shown in the table below.
Scalar = 100/N Where N = Turns through PDCTX
N Scalar N Scalar 1 100 5 20 2 50 10 10 4 25
Maximum Resolvable Current TE10 Determined by the maximum range of the SSR PDCTX 100A (or 100 ampere turns) Finally Exit configuration level. See Chapter 5.
inSt Conf
LC.Hi 100
Installation and Operation Handbook Safety Information
2408 and 2404 Controller E-1
Appendix E: Profibus Communications
Introduction
The 2408f and 2404f are special versions of the 2408 and 2404 controllers designed for Profibus-DP communications. The ‘standard’ 2408 or 2404 controllers cannot be upgraded to a 2408f or 2404f as the latter uses a different version of the microprocessor board.
Profibus-DP is available with either the 85 to 264Vac or 20-29Vac/dc supply
Apart from the restrictions listed below, the operation, functions and wiring of the 2404f and 2404f are identical to that of the standard 2408 and 2404 controllers.
• Modbus communications may be configured to replace Profibus-DP if required. • This must be installed in module slot H. • EI Bisynch protocol is not supported, therefore the IPSG instrument programming
system cannot be used. • The 20 programmer option is not available. • The PDSIO input and output modules can only be installed in module slot J.
About Profibus-DP
Profibus-DP is an industry standard, open network used to connect simple devices in a machine or manufacturing plant. It is most often used to allow a central Programmable Logic Controller or PC based control system to use external ‘slave’ devices for I/O or specialised functions. One advantage is that these devices may be distributed around a machine, saving on the cost of point to point wiring. The ‘open’ nature of the network permits equipment from different manufacturers to be mixed easily so that best of breed equipment may be used. Additionally, the off-loading of specialised tasks such as PID temperature control lessens the processing load on the central PLC so that its other functions may be carried out more efficiently.
Profibus-DP is described in DIN 19245 Part 3, and is part of EN 50170.
The Profibus-DP network uses a high speed version of the RS485 standard, permitting baud rates of up to 12Mbaud. The 2408f and the 2404f support rates of up to 1.5 MBaud in order to meet electrical isolation standards. A table of network speed against line length is given in the section on wiring below.
Up to 32 Profibus stations (nodes) may be wired to a single network segment. Use of RS485 repeaters allows a total of up to 127 stations.
Other variants of Profibus that exist are Profibus FMS, which is designed to allow higher level communication such as that between PLCs and SCADA systems, and Profibus PA, which has an optional low speed, intrinsically safe, physical medium and is designed for use in the Process Industry. The 2408f and 2404f controllers can be used on a combined DP and FMS network, sharing the same physical medium, but may only be used for PA when the intrinisically safe physical medium is not used.
Safety Information Installation and Operation Handbook
E-2 2408 and 2404 Controller
Profibus-DP is a multimaster, master-slave, token passing network. The 2408f and the 2404f operate as intelligent slave units. More detailed information, including a detailed guide to products available, may be obtained from the various world wide Profibus user organisations. You will find contact information in trade magazines or by reference to http://www.profibus.com on the World Wide Web.
Technical Specification
Physical Medium 2-wire RS485
Network topology Linear bus with active termination of the bus at both ends Stub lines permitted if < 6.6m in length
Protocol Profibus-DP, intelligent slave
Baud rate Up to 1.5Mb/s Number of stations 32 per network segment. Up to 127 with repeaters
Electrical Connections
The diagram below is also shown in Chapter 1.
SHIELD
Station 1 HA
HB
HC
HD
HE
HF
Shield
VP (+5Vdc Voltage Potential)
B (Rx/Tx +ve)
A (Rx/Tx -ve)
DGND (Digital ground)
Not connected B
390Ω
Last Station HA
HB
HC
HD
HE
HF
Shield
VP (+5Vdc Voltage Potential)
B (Rx/Tx +ve)
A (Rx/Tx -ve)
DGND (Digital ground)
Not connected
Intermediate stations
Last station only requires terminating resistors
390Ω
220Ω
A
B A
B A
2408f or 2404f controller
2408f or 2404f controller
Twisted pair
Twisted pair
Installation and Operation Handbook Safety Information
2408 and 2404 Controller E-3
Cable Specifications
Either of the two cable types detailed below can be used. Please note that the cable types A and B, specified below, are NOT related to the wire numbers A and B in the above wiring diagram. Type A is recommended as it allows higher speed and longer cable length.
Type A cable Type B cable
Characteristic Impedance:
135 to 165Ω at a frequency of 3 to 20 MHz.
135 to 165Ω at a frequency of > 100 kHz
Cable capacitance: < 30 pF per Metre typ. < 60 pF per Metre
Core diameter: max. 0.34 mm², corresponds to AWG 22
max. 0.22 mm², corresponds to AWG 24
Cable type: twisted pair cable. 1×2 or 2×2 or 1×4 lines
twisted pair cable. 1×2 or 2×2 or 1×4 lines
Resistance: < 110 Ohm per km —
Shielding: Copper shielding braid or shielding braid and shielding foil
Copper shielding braid or shielding braid and shielding foil
Maximum Line Length per Segment
Baud rate (kbit/sec) 9.6 19.2 93.75 187.5 500 1500
Type A cable 1200m 1200m 1200m 1000m 400m 200m
Type B cable 1200m 1200m 1200m 600m 200m —
Belden B3079A meets cable A specifications, but there are other choices. For more information refer to the ‘Profibus Product Guide’ produced by the Profibus User Group.
Safety Information Installation and Operation Handbook
E-4 2408 and 2404 Controller
Controller Configuration and Node Address
Having connected the controller to the network, it must be configured for Profibus communications and a node address assigned. Configuration
In the HA list set Func = ProF. Note: The baud rate is automatically selected by the master. Assigning a Node Address Refer to the main handbook for instructions on how to select and change parameters.
HA ConF
id
CmS
Func
ProF
rEs
FULL
Comms configuration list — HAHAHAHA Refer to the main handbook for instructions on how to select configuration level and access the HA list
Identity of module This should be a read-only parameter displaying Cms
Resolution FuLL = Full, Int = Integer This is the only other parameter that appears in this list when ProF is selected as the function.
Function Set Func = Prof to select Profibus protocol
cmS LiSt
Addr
1
Stat
run
Comms list From the HOME display, press until you reach the cmS list
Node address Press to display the node address. Press or to set the desired address. 0 -126
Comms Status This is a read-only diagnostic display rdy Ready to run run Comms running
Installation and Operation Handbook Safety Information
2408 and 2404 Controller E-5
Network configuration
Having wired and configured the controller, the PLC or PC based supervisory package must be configured to set-up the parameters that it will be able to read and write to. This is known as ‘network configuration’
The network is configured by importing ‘GSD’ files into your Master Profibus network configuration software: Refer to the network configuration software documentation for details. ‘GSD’ is an acronym of a German phrase meaning ‘Device Database’.
GSD files for the 2408f and 2404f controllers are created using a Windows based configuration tool. This is separately supplied under ordering code PROF-ENG. A Communications Handbook (part number HA026290ENG), supplied with the configurator, gives all the required information
Two standard GSD files, are supplied on the disc:
EURO2400.GSD standard parameter mapping EURD2400.GSD standard parameter mapping with ‘demand data’, which
allows random read/write to any parameter within the controller.
It is possible to edit the above files or create new files using the Windows configurator. Details are given in the communications handbook.
The Master network configuration software uses the GSD files to produce a further file which is downloaded into your master PLC or PC supervisory package. Once the configuration file has been downloaded, you can set the network running. If all is well, the ‘REM’ beacon on the controller will start to flash, indicating that the data exchange is proceeding. The Stat parameter in the cMS list will show run. You may then write to Profibus outputs, and read from Profibus inputs as required by your control strategy.
In case of problems, a troubleshooting section is provided on the next page.
How many parameters can I select?How many parameters can I select?
Click on the tabs at the bottom ofthe device parameter window toselect a parameter page. Then usethe mouse to drag a requiredparameters into either the Profibusinput or output lists.
How do I use it?How do I use it?
Windows configuratorWindows configurator
Windows 3.1, Windows 95, orWindows NT.
What can I run it on?What can I run it on?
Up to 117 per node, total of inputs andoutputs.
What does it do?What does it do?It creates a ‘GSD’ file which definesthe inputs and outputs that the PLC orsupervisory package will be able totalk to. The GSD file is imported intoa Profibus Master configuration toolwhich in-turn produces a file that isdownloaded into the PLC orsupervisory package.
Safety Information Installation and Operation Handbook
E-6 2408 and 2404 Controller
Troubleshooting No Communications: • Check the wiring carefully, paying particular attention to the continuity of the A and B
connections to the Master. Ensure that the correct terminals have been wired to. • Access the HA list in configuration level and check that the function (Func) is set to
Prof. If not, the controller is not configured for Profibus. • Check that the Node Address (Addr) in the cMS list is correct for the network
configuration in use. • Ensure that a Profibus Comms Module is installed in slot H of the 2404/8f. It can be
identified by of the legend on the plug-in module casing, and its distinctive shape: • Ensure that the network is correctly configured and the configuration has been
transmitted correctly to the Profibus master. • Verify the GSD file in use is correct by loading it into the master GSD Configuration
tool. This will check the format. • Verify that the maximum line length for the baud rate in use is not exceeded (see table
above). Note that the 2404/8f is restricted to use at a maximum rate of 1.5 Mbaud. • Ensure that the last device (not necessarily a 2404/8f) in the network segment is
correctly terminated (see wiring diagram). • Ensure that no devices other than those at the end of a segment have termination
networks fitted. • If possible, replace faulty device with a duplicate and retest.
Intermittent failure to communicate. Intermittent flickering of status from rdyrdyrdyrdy to runrunrunrun. Diagnostic status changing but no alarms present in the controller.
• Verify wiring, paying particular attention to screening. • The I/O data length may be too long. Some Profibus DP Master implementations can
accept no more than 32 input and 32 output words per slave device. Verify by reference to documentation of the Master.
• Verify that the maximum line length for the baud rate in use is not exceeded (see cable specifications). Note that the 2404/8f is restricted to use at a maximum rate of 1.5 Mbaud.
• Ensure that the last device (not necessarily a 2404/8) in the network segment is correctly terminated (see wiring diagram).
• Ensure that no devices other than those at the end of a segment have termination networks fitted.
• Verify operation with a duplicate device if possible.
SUB24/PB PROFIBUS Iss No. AH026222 U002 DATE
INTERNATIONAL SALES AND SERVICE
HA025132
© Copyright Eurotherm Limited 2004
All rights are strictly reserved. No part of this document may be reproduced, modified, or transmitted in any form by anymeans, nor may it be stored in a retrieval system other than for the purpose to act as an aid in operating the equipment towhich the document relates, without the prior written permission of Eurotherm limited.
Eurotherm Limited pursues a policy of continuous development and product improvement. The specifications in this docu-ment may therefore be changed without notice. The information in this document is given in good faith, but is intended forguidance only. Eurotherm Limited will accept no responsibility for any losses arising from errors in this document.
http://www.eurotherm.co.uk
ENG
AUSTRALIA SydneyEurotherm Pty. Ltd.Telephone (+61 2) 9838 0099Fax (+61 2) 98389288
AUSTRIA ViennaEurotherm GmbHTelephone (+43 1) 7987601Fax (+43 1) 7987605
BELGIUM Moha &LUXEMBURG HuyEurotherm S.A./N.V.Telephone (+32 ) 85 274080Fax (+32 ) 85 274081
BRAZIL Campinas-SPEurotherm Ltda.Telephone (+55 19) 3237 3413Fax (+55 19) 3234 7050
DENMARK CopenhagenEurotherm Danmark A/STelephone (+45 70) 234670Fax (+45 70) 234660
FINLAND ABOEurotherm FinlandTelephone (+358) 22506030Fax (+358) 22503201
FRANCE LyonEurotherm Automation SATelephone (+33 478) 664500Fax (+33 478) 352490
GERMANY LimburgEurotherm Deutschland GmbHTelephone (+49 6431) 2980Fax (+49 6431) 298119Also regional offices
HONG KONG AberdeenEurotherm LimitedTelephone (+852) 28733826Fax (+852) 28700148
INDIA ChennaiEurotherm India LimitedTelephone (+9144) 24961196Fax (+9144) 2256682070
IRELAND DublinEurotherm Ireland LimitedTelephone (+353 01) 4691800Fax (+353 01) 4691300
ITALY ComoEurotherm S.r.lTelephone (+39 031) 975111Fax (+39 031) 977512
KOREA SeoulEurotherm Korea LimitedTelephone (+82 31) 2738507Fax (+82 31) 2738508
NETHERLANDS Alphen a/d RynEurotherm B.V.Telephone (+31 172) 411752Fax (+31 172) 417260
NORWAY OsloEurotherm A/STelephone (+47 67) 592170Fax (+47 67) 118301
SPAIN MadridEurotherm España SATelephone (+34 91) 6616001Fax (+34 91) 6619093
SWEDEN MalmoEurotherm ABTelephone (+46 40) 384500Fax (+46 40) 384545
SWITZERLAND FreienbachEurotherm Produkte (Schweiz) AGTelephone (+41 55) 4154400Fax (+41 55) 4154415
UNITED KINGDOM WorthingEurotherm LimitedCONTROLS & DATA MANAGEMENTTelephone (+44 1903) 695888Fax (+44 1903) 695666PROCESS AUTOMATIONTelephone (+44 1903) 205277Fax (+44 1903) 236465
U.S.A LeesburgEurotherm Inc.Telephone (+1 703) 443 0000Fax (+1 703) 669 1300Web www.eurotherm.com
ED 38