Faac e124 инструкция на русском

• Important! For the safety of people, it is important that all the instructions be carefully observed.

• Incorrect installation or incorrect use of the product could cause serious harm to people.

• Carefully read the instructions before beginning to install the product and keep them for future reference.

•

The symbol

indicates notes that are important for the safety of persons and for the good condition of the automated system.

• The symbol

draws your attention to the notes on the characteristics and operation of the product.

•

Before attempting any work on the control unit (connections, maintenance), always turn off power.

•

Install, upstream of the system, a differential thermal breaker with adequate tripping threshold,

•

Connect the earth cable to the relevant terminal (see fig.5).

•

Always separate power cables from control and safety cables (push-button, receiver, photocells, etc.). To avoid any electrical disturbance, use separate

sheaths or a screened cable (with the screen earthed).

Manufacturer: FAAC S.p.A.

Address:

Via Benini,  — 40069 Zola Predosa BOLOGNA — ITALY

Declares that: The E24 control unit

• ·conforms to the essential safety requirements of the following EEC directives

2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic Compatibility Directive

Additional note:

Bologna, 01 March 2008

4

TECHNICAL SPECIFICATIONS

Primary power feed

from mains

Secondary power

feed

Power absorbed

from mains

Max. load

for motor

Power feed

for accessories

Accessories

max. current

Battery charge

current

Operating ambient

tempeature

Protective fuses

Function logics

«step-by-step» Semiautomatic, Automatic

with reverse during pause, Automatic

step-by-step, Safety devices automatic,

Safety devices step-by-step automatic,

«b» Semiautomatic, mixed logic «bC»,

Dead-man, Automatic with timer function

Work time

Programmable (from 0 to 4 minutes)

Pause time

Programmable (from 0 to 4 minutes)

Motor power

Motor speed

E124 control unit – rapid guide

CE DECLARATION OF CONFORMITY

This product underwent tests in a typical uniform configuration

(all products manufactured by FAAC S.p.A.).

with switching power feed

230/5 V~ — 50/60 Hz

24 Vdc — 6 A max.

(min. 20 Vdc. — max. 28 Vdc.)

stand-by = 4W

max. ~ 400 W

7 A

24 Vdc

24Vdc max. 500 mA

BUS-2EASY max. 500 mA

80 mA

(-20 — +55) °C

All self resetting

Semiautomatic, Automatic,

Programmable on 50 levels

Programmable on 0 levels

WARNINGS

The Managing Director

A.Marcellan

Connector inputs

Terminal board inputs

Terminal board outputs

Programming

These instructions are to be considered

as a rapid guide for installation. The complete

instructions can be downloaded at the following

address: www.faacgroup.it

To access PROGRAMMING FROM PC, use the

X-COM module or connect the USB cable to the

dedicated connector and consult the dedicated

instructions.



Switching feeder, Battery,

Decoder/Minidec/RP , X-COM, module

XF433/868, USB

BUS-2EASY, Inputs from IN to IN5 (see

par. 5), Travel limit device, Encoder.

Flashing lamp, Motors, Electrical lock,

OUT, OUT2 (programmable), power feed

to accessories

st and 2° lev. with 3 keys (+, -, F) and LCD

display.

3rd lev. with P .C. connected via USB or with

X-COM module.

FAAC E124 — Инструкция по установке и эксплуатации (RU) в формате pdf. Руководства по установке, настройке и эксплуатации оборудования.

Отзывы и комментарии

Отзывы и комментарии к материалу «FAAC E124 — Инструкция по установке и эксплуатации (RU)».