Инструкция maha powerex mh c9000

MH-C9000

WizardOne Charger-Analyzer

Thank you for purchasing the Powerex MH-C9000

Charger-Analyzer. Read these instructions carefully

and thoroughly before operating this unit. IMPORTANT

SAFETY INSTRUCTIONS. READ AND SAVE THESE

INSTRUCTIONS.

OPERATING THIS PRODUCT INCORRECTLY CAN

CAUSE DAMAGE TO THE BATTERIES.

READ MANUAL COMPLETELY BEFORE USE.

GENERAL PRECAUTIONS

·

Do not charge battery cells other than NiMH or NiCD. Please check

with the battery manufacturer to ensure it can accept the

programmed charging and discharging rates. Do not expose the unit

to rain or moisture due to the risk of fire.

·

Do not operate the charger if it appears damaged in any way.

·

Always place the battery cells with positive tip facing the top.

Incorrect polarity may cause fire or explosion. Observe polarity

diagrams located on the charger.

·

Do not allow the unit to be exposed to direct sunlight. Operate in a

well-ventilated area. Do not place unit on the carpet.

·

Do not allow the battery terminals to become shorted.

·

To reduce the risk of damage to the power cord, always pull by

connector rather than the cord.

·

Use only the supplied adapter or optional regional and car adapter

offered by Maha Energy. Using third party accessories voids the

product warranty.

FEATURES & SPECIFICATIONS

·

Four independent slots for AA or AAA NiMH batteries.

·

Backlit LCD display.

·

Digitally displays capacity, voltage, time and current.

·

Five modes of operation: Charge, Refresh & Analyze, Break-In,

Discharge and Cycle.

·

19 selectable charging current from 0.2A to 2.0A.

·

10 selectable discharging current from 0.1A to 1.0A.

·

Worldwide power supply.

Charging Current:

Topoff Charging Current:

Maintenance Charging

Current:

Discharge Termination:

Discharging Current:

PRINTED IN TAIWAN A03-3713420-511

Programmable from 0.2A to 2.0A in

increments of 0.1A

100mA

10mA

Voltage 0.90V

Programmable from 0.1A to 1.0A in

increments of 0.1A

Capacity Storage Memory:

Supported Capacity*:

Charger Input Power:

Adapter Input:

* Always ensure that the batteries can accept the programmed rates.

GENERAL BATTERY EDUCATION

What is 0.1C, 0.2C, etc?

«C» stands for the battery capacity and the number preceeding it is the

fraction of the battery capacity. For example, 0.1C means 0.1 times the

capacity for the battery. For a 2700mAh battery, 0.1C would be 0.1 times

2700mAh which equals 270mA.

Choosing the right charging & discharging rate

Charging at a rate below 0.3C and above 1.0C is not recommended.

Charging too slow may prevent the charger from terminating correctly.

Charging too fast may damage the battery.

Typically speaking, slower charging rate will yield better battery

performance but requires longer time. Faster charging rate may not

charge as fully and battery temperature can be higher.

As for the discharging rate, do not exceed 1.0C.

Battery Matching

In most devices, usually two or more batteries are used together. When

batteries are used in a series, the performance is limited by the worst

one. In other words, one poorly performing battery can significantly

reduce the device runtime.

Battery matching refers to grouping batteries with similar «actual»

capacity. To perform this, use the Refresh & Analyze mode to determine

the battery capacity. Group batteries with capacity within about +/- 5% of

the rated capacity.

Battery «Forming»

New batteries and those stored for extended period become chemically

deactivated. Battery forming is a charge-discharge-charge cycle which

forces a full charge into the battery at a very slow rate. This process

activates the battery. In certain cases, it needs to be repeated two or

three times.

Battery forming can be performed using the Break-In mode.

12 (Cycle mode only)

100 to 20,000mAh

12V 2.0A

100-240V 50/60Hz


Maha MH-C9000 это лучшее по мнению магазина La-Crosse.ru зарядное устройство для обслуживания аккумуляторов АА/ААА.

Сравнение с La Crosse можно прочитать здесь.

FAQ по зарядному устройству Maha MH-C9000

Основные характеристики зарядного устройства MAHA MH-C9000:

Производитель: Maha Energy Corp., США.
Совместимые аккумуляторы: Работает со всеми NiCd и NiMH аккумуляторами формата “AA”, “AAA”.
Емкость аккумуляторов: 100-20000mAh
Допустимое напряжение сети: 100-240 В.
Ток заряда: 200 mA — 2000 mA.
Ток разряда: 100 — 1000 mA.

Подробное описание:

Работает со всеми NiCd и NiMH аккумуляторами формата “AA”, “AAA”.

Четыре независимых канала

Большой ЖК экран с подсветкой

Показывает мощность, напряжение, время и емкость в цифровом виде.

Бесконечные программные возможности — более чем 10 000 вариантов!

29 уровней заряда/разряда. Зарядный ток от 0.2A до 2.0A, разрядный от 0.1A до 1.0A с шагом 0.1A.

Пять режимов работы

Charge: Заряжает аккумулятор выбранным током.

Рекомендуется для часто используемых аккумуляторов .

Refresh & Analyze: Заряжает батарею, пауза в течение одного часа, разряжает, снова пауза, затем окончательный заряд. Можно выбрать токи заряда и разряда.

Рекомендуется для аккумуляторов не используемых более двух недель, но менее 3-х месяцев, или для тех которые показывают низкую производительность.

Break-In: «Формовка аккумуляторов». Аккумулятор заряжается током 0.1C в течение 16 часов, отдых в течение одного часа, разряд током 0.2C, затем снова заряд током 0.1C в течение 16 часов.

Рекомендуется для новых элементов питания и не используемых более 3-х месяцев.

Discharge: Разряжает аккумулятор выбранным током.

Cycle: Выполняет 12 циклов заряд/разряд. Перезаряжает батарею после заключительного цикла.

Новые способы заботиться о Ваших аккумуляторах и максимизировать время работы!

Поиск плохих аккумуляторов

В большинстве устройств обычно используются вместе два и более элементов питания. Их общая производительность ограничена худшим. Другими словами одна плохо работающая батарея может значительно сократить время работы устройства.

Формовка аккумуляторов

Новые и не используемые в течение длительного периода батареи становятся химически неактивны. Формовка является циклом заряд-разряд-заряд, который восстанавливает аккумуляторы очень небольшим током. Этот процесс активирует батарею. Иногда необходимо повторить два или три раза.

Передает только правильный заряд

Контроль независимой -dV, датчики температуры (4) и таймер гарантируют безопасную зарядку аккумуляторов

Комплект поставки:

  • Зарядное устройство
  • Блок питания от сети 100-240 В, с отечественной вилкой
  • Инструкция

Версия прошивки:

На зарядном устройстве установлена последняя версия прошивки

Гарантия:

На все зарядные устройства, продаваемые в нашем магазине мы предоставляем 1 год гарантии

Инструкция пользователя на русском языке:

Инструкцию пользователя в формате PDF можно скачать по ссылке здесь

Узнать больше:

  • Зарядные устройства Maha Powerex MH
  • Скидка на Maha
  • Инструкции к зарядным устройствам
  • Ответы на часто задаваемые вопросы (FAQ) по устройствам Maha
  • La Crosse vs Maha. Какое зарядное устройство купить?
  • Гарантия на зарядные устройства и условия возврата
  • Сертификаты на продукцию
  • Основные преимущества интеллектуального зарядного устройства — краткое и понятное сравнение
  • Лучшие зарядные устройства для аккумуляторов АА и ААА — читайте наше мнение
  • Информация о доставке — работаем со всеми регионами


Мнения покупателей:

  (Воскресенье, 15 Май 2016)

Рейтинг:
5

2 в 1 — зарядное устройство + ночник как бонус :-) Хорошая машина! Удобная, добротная,
солидная и многофункциональная. Выбирал по производителю. Увидел, что Maha Energy Corp.
находится в США и купил. Понятно, что производство размещено в Тайване, но всё
равно это американское качество и товар который сделан ДЛЯ ЛЮДЕЙ.

  (Четверг, 07 Январь 2016)

Рейтинг:
5

Зарядное устройство-супер! Долго выбирал между им и La-Crosse.Выбрал MAHA Powerex MH-C9000 и ни
разу не пожалел.Как только принёс домой, поставил тэстить и восстанавливать 4
комплекта (по 4 шт.) старых аккумуляторов, которым более 5 лет.Маха не выключалась 9
дней. Из 16 шт.5 шт оказались убитыми(4-GP и 1-Philips), у остальных (Sony,Camelion и Philips) реально
удалось повысить ёмкость.Про недостатки, которые пишут, считаю это всё ерунда,
свет не такой уж и яркий, а мизинчиками я не пользуюсь, так,что ток по умолчанию в
1000мА для меня не страшен. Считаю, что данное зу на сегодняшний день-лучшее!
Рекомендую!!!

  (Воскресенье, 15 Ноябрь 2015)

Рейтинг:
5

Зарядник — супер! До этого пользовался SONY BCG-34HRMF4N — это Земля и Небо просто. Maha
обнаружил 4 сдохших аккума Sony CycleEnergy 2700 (made in Japan), наверное это те, которые в
комплекте с соневской зарядкой шли (есть и другие), судя по дате изготовления они
до покупки около 1,5 лет по складам мотались, это на них сказалось видимо.
Зарядником очень доволен, особенно нравится, что можно присоединить шнурок для
питания от прикуривателя и питать его от 12 Вольт. Всем нравится, единственное, что
немного напрягает, это то, что подсветку нельзя выключить самому или хотя бы
приглушить, а то ночью как ночник светит прямо, пол комнаты освещает. Долго
выбирал какой же купить? Но выбор остановился именно на Powerex MH-C9000. Перед покупкой
основательно прошерстил все отзывы и обзоры и выбрал именно его, кто еще
сомневается могу порекомендовать брать именно C9000. В дополнение к нему заказал
еще и Kweller X-2000, чтобы с аккумы типа С и Li-ion заряжать можно было.

  (Вторник, 21 Апрель 2015)

Рейтинг:
5

Очень доволен покупкой!!! Все, что есть, всё зарядил!)))) Тоже долго думал между LA CROSSE
BC-700 и этим зарядником. После штудирования интернета, для себя сделал правильный
выбор!

  (Суббота, 04 Апрель 2015)

Рейтинг:
5

Если вы это читаете, значит вам это надо. И я когда то перелопатил кучу отзывов об
этом магазине и зарядном устройстве MAHA Powerex MH-C9000. Отличное зарядное устройство!
Ваши сомнения рассеются, когда вы приобретёте эту зарядку в этом магазине!

  (Пятница, 31 Октябрь 2014)

Рейтинг:
5

  (Среда, 10 Сентябрь 2014)

Рейтинг:
5

Выбирал между La-Crosse и Махой, остановился на последнем. Магазин отработал
оперативно, претензий никаких нет. При заказе получил скидку, а также подарок —
сумку для аккумов (я брал 4 упаковки аккумов, коробку и саму зарядку). Сегодня буду
пробовать всякое. Удачи в работе сотрудникам магазина!

  (Среда, 30 Июль 2014)

Рейтинг:
5

Долго не мог решиться между LA CROSSE BC-700 и MAHA Powerex MH-C9000. Заказал Маху и наборы акков
ААА и АА. В Самару заказ пришел за 5 дней по почте с бесплатной доставкой. Коробка с
махой упакована была в пузырчатую пленку. На ебее получается дороже и ждать
неизвестно сколько. Достойный магазин! Скорее всего докуплю LA CROSSE BC-700. Пусть в
паре трудятся, дополняя друг друга. Цена уже не такая кусачая. Для рукастых можно
проапгрейдить аппарат сопротивлением и пригасить подсветку. Но оно вам надо? PS
программеры проверьте сайт, я замучился отзыв добавлять, все время ругается что
написал более 2000 знаков, хотя по факту было 1300.

  (Среда, 30 Июль 2014)

Рейтинг:
5

Отличное зарядное устройство!О небольших недостатках прошивки написали другие
авторы. Перезарядил десяток GP2500. Срок службы — около 3 лет. У большинства реальная
емкость оказалась не выше 80% от заявленной производителем :(.

  (Вторник, 18 Февраль 2014)

Рейтинг:
5

Когда Вы его включите , Вас будет распирать от гордости. Показать другим не то что
не стыдно , но даже хочется. Серьезное устройство по весу, виду, качеству
материалов, функционалу. Это как после китайского джипа приобрести GL500 ).

  (Воскресенье, 03 Ноябрь 2013)

Рейтинг:
5

На мой взгляд самый правильный зарядник даже из серии интеллектуальных, не говоря
про все остальное, ну наверное единственный недостаток у него, это то что
параметры зарядки нужно вводить для каждого аккума отдельно и не предусмотрен
режим памяти для пользовательских предустановок, но это все ерунда по сравнению с
тем какие возможности заложены в нем.Рекомендую, он стоит своих денег!

  (Четверг, 10 Октябрь 2013)

Рейтинг:
5

После покупки портативного рекордера я задался вопросом о покупки аккумуляторов
и так как я люблю долго покопаться на форумах, почитать различную информацию и
отзывы в магазинах, то я сразу же наткнулся на интернет магазин la-crosse.ru и был
приятно удивлён наличием всей профессиональной продукции связанной с
аккумуляторами и зарядками, там же нашёл много полезной информации о всём что
связанно с процессом зарядки, разрядки и т.д. Всем советую этот магазин! rnБыл
приятно удивлён скоростью доставки, так как посылка была отправлена 29 сентября, а
сегодня 10 октября я уже являюсь счастливым обладателем отличного зарядного
устройства MAHA Powerex MH-C9000 и аккумуляторов Sanyo Eneloop XX. Теперь я точно их постоянный
клиент! Всем удачных покупок!

  (Пятница, 12 Июль 2013)

Рейтинг:
5

Отличный зарядник! Тем у кого стоит выбор маха-лакрос нужно взять себя в руки и
решиться. Плюсы (для меня): 1. расстояния между аккумуляторами — греются они, но не
сильно, и уменьшать эти расстояния неразумно, поэтому судя по отзывам, если для
махи перегрев ситуация исключительная, то для лакроса нормальная рабочая; 2.
разные режимы для разных слотов (важно в самом начале использования зарядника,
когда есть куча аккумуляторов, и к каждому нужен индивидуальный подход). Минус (не
только для меня): после сбоя электричества режим по умолчанию — заряд током 1А, т.е.
для аккумуляторов ААА это будет очень жестоко. Поскольку использую исключительно
АА емкостью 2300-2500мА, эта особенность для меня плюс (установил аккум и не нужно
делать ничего). Конечно, можно сделать ток и побольше, если нужно срочно
зарядиться, но аккумуляторы будут недозаряжены и перегреты. Из 11 аккумов нашлась
одна паршивая овца, но после рефреша вернулась в строй. Берите, не пожалеете!
Разницу по деньгам уже через неделю не вспомните, а аппарат будет радовать.

  (Пятница, 30 Ноябрь 2012)

Рейтинг:
5

Лучшее ЗУ в мире!

  (Понедельник, 13 Февраль 2012)

Рейтинг:
5

На днях приобрёл этот чудо аппарат, даволен 100 пудово. Выберал между La-Crosse и им,
отдал предпостение Махе! Это тем кто не решится никак, как я до покупки! Магазин
хорошо сработал, молодци, да и почта на удевление, за неделю дошел! Я часто в нет
магазинах затариваюсь и надо сказать этот магаз, на высоком уровне!!! Аппарат у
меня определил уже штук 5-ть мертвых ак-ов, причем проверял потом я еще, заряжая на
обычной и разряжая на Махе, все не дотягивали даже до 10% своей ёмкости, при
мизерном токе разряда. Значит ему можно верить, отказывается заряжать, значит акк
мёртв! Вобщем штука клёвая, если бобла хватает, берите, не пожалеете, с ним я стал
понимать, как галимо заряжают обычные зарядки, даже не дешовые (за штуку, где-то). У
меня их, по мимо этой 4 шт. Акки начинают с Махой работать стабильней (разряжаются
равномерно например в сборке из 4-х акк) и дольше. Вобщем пока сам не попробуеш не
поймёш. Всем удачи!

Maha Energy MH-C9000 User Manual

MH-C9000

WizardOne Charger-Analyzer

Thank you for purchasing the Powerex MH-C9000 Charger-Analyzer. Read these instructions carefully and thoroughly before operating this unit. IMPORTANT SAFETY INSTRUCTIONS. READ AND SAVE THESE INSTRUCTIONS.

OPERATING THIS PRODUCT INCORRECTLY CAN CAUSE DAMAGE TO THE BATTERIES.

READ MANUAL COMPLETELY BEFORE USE.

GENERAL PRECAUTIONS

Do not charge battery cells other than NiMH or NiCD. Please check with the battery manufacturer to ensure it can accept the programmed charging and discharging rates. Do not expose the unit to rain or moisture due to the risk of fire.

Do not operate the charger if it appears damaged in any way.

Always place the battery cells with positive tip facing the top. Incorrect polarity may cause fire or explosion. Observe polarity diagrams located on the charger.

Do not allow the unit to be exposed to direct sunlight. Operate in well-ventilated area. Do not place unit on the carpet.

Do not allow the battery terminals to become shorted.

To reduce the risk of damage to the power cord, always pull by connector rather than the cord.

Use only the supplied adapter or optional regional and car adapter offered by Maha Energy. Using third party accessories voids the product warranty.

FEATURES & SPECIFICATIONS

Four independent slots for AA or AAA NiMH batteries.

Backlit LCD display.

Digitally displays capacity, voltage, time and current.

Five modes of operation: Charge, Refresh & Analyze, Break-In, Discharge and Cycle.

19 selectable charging current from 0.2A to 2.0A.

10 selectable discharging current from 0.1A to 1.0A.

Worldwide power supply.

Charging Current:

Programmable from 0.2A to 2.0A in

increments of 0.1A

Topoff Charging Current:

100mA

Maintenance Charging

10mA

Current:

Discharge Termination:

Voltage 1.00V

Discharging Current:

Programmable from 0.1A to 1.0A in

increments of 0.1A

Capacity Storage Memory:

12 (Cycle mode only)

Supported Capacity*:

100 to 20,000mAh

Charger Input Power:

12V 2.0A

Adapter Input:

100-240V 50/60Hz

* Always ensure that the batteries can accept the programmed rates.

GENERAL BATTERY EDUCATION

What is 0.1C, 0.2C, etc?

“C” stands for the battery capacity and the number in front of it is the fraction of the battery capacity. For example, 0.1C means 0.1 times the capacity for the battery. For a 2700mAh battery, 0.1C would be 0.1 times 2700mAh which equals 270mA.

Choosing the right charging & discharging rate

Charging at a rate below 0.33C and above 1.0C is not recommended.

Charging too slow may prevent the charger from terminating correctly. Charging too fast may damage the battery.

Typically speaking, slower charging rate will yield better battery performance but requires longer time. Faster charging rate may not charge as fully and battery temperature can be higher.

Battery Matching

In most devices, usually two or more batteries are used together. When batteries are used in a series, the performance is limited by the worst one. In other words, one poorly performing battery can significantly reduce the device runtime.

Battery matching refers to grouping batteries with similar “actual” capacity. To perform this, use the Refresh & Analyze mode to determine the battery capacity. Group batteries with capacity within about +/- 5% of the rated capacity.

Battery “Forming”

New batteries and those stored for extended period become chemically deactivated. Battery forming is a charge-discharge-charge cycle which forces a full charge into the battery at a very slow rate. This process activates the battery. In certain cases, it needs to be repeated two or three times.

Battery forming can be performed using the Break-In mode.

PRINTED IN TAIWAN A03-3713420-496

MODES OF OPERATION

This section explains various modes and when to use them. To enable each mode, refer to the “Operation” section.

Charge Mode

Recharges the battery at the selected rate.

Useful when battery needs to be recharged without determining the capacity of the battery. It should be used on batteries known to be in good condition and have been in continuous use.

Requires the least amount of time.

Refresh & Analyze Mode

First recharges the battery, rest for one hour, discharge, rest, then recharges again. Charging and discharging rates are programmable.

Reports the discharge capacity at the end of the cycle.

Useful when the battery capacity needs to be determined. Also useful for battery with degraded performance.

Recommended once every ten cycles for NiMH batteries.

Break-In Mode (IEC capacity analysis)

Applies a 16-hour 0.1C charge (0.1 times the capacity of the battery), rest of one hour, followed by a 0.2C discharge, rest again, and finally a 16-hour 0.1C recharge again.

Recommended for brand-new batteries. This process is also known as “Forming Charge.” Also recommended with batteries that cannot be rescued by the Refresh & Analyze mode.

Recommended once every 30 cycles for NiMH batteries.

Requires 39 to 45 hours to complete.

The process follows the IEC standard for determining battery capacity.

Discharge Mode

Discharges the battery at the selected rate.

Useful for analyzing the amount of charge stored in the battery. Battery not recharged at the end of the cycle.

Cycle Mode

Performs a charge-discharge cycle for the programmable number of times. Charging and discharging rates are also selectable. At the end of the cycle, a final recharge is applied.

Suitable for cycling the batteries multiple times.

The following table summarized the recommended mode for typical battery conditions:

Battery Condition

Mode

Brand-new batteries

Break-In

NiMH batteries that have been used

Charge

frequently (at least once every two weeks)

Batteries in storage for more than two

Refresh & Analyze

weeks but less than 3 month

Batteries in storage for more than 3 month

Break-In

Batteries showing poor performance

Refresh & Analyze for

one to three times.

Battery Rescue Steps

For batteries that do not perform favorably after using the mode recommended above, the following sequence can be applied.

1.Refresh & Analyze for one to three times.

2.If capacity is still low, use Break-In mode.

3.If the step 1 to step 2 shows some capacity improvement (> 10%), repeat Break-In mode for one to three times. If no significant improvement, battery probably at end of useful life.

OPERATIONS

1.Connect the power adapter DC connector to the charger.

Then, plug the power adapter into a compatible outlet (100-240VAC, 50/60Hz).

TIP: When operating the charger outside of its intended region of use, simply use a plug-changer (Maha part number MHS-TC400 worldwide plug-changer kit). Transformer is not necessary.

2.Raise the lift rod located on the backside of the charger.

3.Insert AA or AAA battery.

Inserting AA batteries

Inserting AAA batteries

TIP: If charging two batteries, inserting them in the first and fourth slot offers better cooling and lowers battery temperature.

4.When a new battery is detected, the LCD will display an arrow below the bank number and prompt for the mode by flashing “MODE”.

Use the UP and DOWN arrow keys to choose the desired mode. Press ENTER to make the selection.

If no key is pressed within five seconds, the charger will proceed to the default mode which is charging with 1000mA rate.

NOTE: the default mode may not be suitable for battery lower than 500mAh and higher than 1500mAh. See “General Battery Education” for more details.

If more than one battery is inserted at a time (without key press), the charger will prompt for programming in the order in which the batteries were inserted.

5.If CHARGE mode is selected:

The charger will prompt for the charging rate by flashing “SET CHG RATE.” Use the UP and DOWN key to choose the desired current. Press ENTER to make the selection. Refer to the “General Battery Education” section on choosing an appropriate rate.

PRINTED IN TAIWAN A03-3713420-496

Loading…

Specifications:

541/541102-mhc9000.pdf file (15 Jun 2023)

Accompanying Data:

Maha Energy MH-C9000 Battery Charger PDF Manual  (Updated: Thursday 15th of June 2023 02:45:06 PM)

Rating: 4.4 (rated by 8 users)

Compatible devices: TPL73-A32, NEMO Series, START BOOSTER 12V, CVTR2, 73399, NCU120 series, MH-C2000, 99-0001-001.

Recommended Documentation:

Manual  (Text Version):

(Ocr-Read Summary of Contents of some pages of the Maha Energy MH-C9000 Document (Main Content), UPD: 15 June 2023)

  • 1, Maha Energy MH-C9000 PRINTED IN TAIWAN A03-3713420-496 Thank you for purchasing the Powerex MH-C9000 Charger-Analyzer. Read these instructions carefully and thoroughly before operating this unit. IMPORTANT SAFETY INSTRUCTIONS. READ AND SAVE THESE INSTRUCTIONS. OPERATING THIS PRODUCT INCORRECTLY CAN CAUSE DAMAGE TO THE…

  • 2, PRINTED IN TAIWAN A03-3713420-496 MODES OF OPERATION This section explains various modes and when to use them. To enable each mode, refer to the “Operation” section. Charge Mode • Recharges the battery at the selected rate. • Useful when battery needs to be recharged without deter…

  • 3, Maha Energy MH-C9000 PRINTED IN TAIWAN A03-3713420-496 If REFRESH & ANALYZE mode is selected: The charger will prompt for the charging rate by flashing “SET CHG RATE.” Use the UP and DOWN key to choose the desired current. Press ENTER to make the selection. Then it will prompt from the discharg…

  • 4, PRINTED IN TAIWAN A03-3713420-496 Note the charging capacity is usually higher than the actual capacity of the battery owing to some energy lost as heat. Charging capacity cannot be used to judge the performance the battery. Instead, it can only be used to determine the progress of the charger. It is norma…

  • Maha Energy MH-C9000 User Manual

  • Maha Energy MH-C9000 User Guide

  • Maha Energy MH-C9000 PDF Manual

  • Maha Energy MH-C9000 Owner’s Manuals

Recommended: VIP-L16 -, KX-TC2100HK, MAP-GD35U3, Lifebook TH700

Product Types by Maha Energy:
  • Battery Charger

Operating Impressions, Questions and Answers:

PRINTED IN TAIWAN A03-3713420-496 

 
Thank you for purchasing the Powerex MH-C9000 
Charger-Analyzer. Read these instructions carefully 
and thoroughly before operating this unit. IMPORTANT 
SAFETY INSTRUCTIONS. READ AND SAVE THESE 
INSTRUCTIONS. 
 

OPERATING THIS PRODUCT INCORRECTLY CAN 

CAUSE DAMAGE TO THE BATTERIES. 

READ MANUAL COMPLETELY BEFORE USE.  

GENERAL PRECAUTIONS 

Do not charge battery cells other than NiMH or NiCD. Please check 
with the battery manufacturer to ensure it can accept the 
programmed charging and discharging rates. Do not expose the unit 
to rain or moisture due to the risk of fire. 

• 

Do not operate the charger if it appears damaged in any way. 

• 

Always place the battery cells with positive tip facing the top. 
Incorrect polarity may cause fire or explosion. Observe polarity 
diagrams located on the charger. 

• 

Do not allow the unit to be exposed to direct sunlight. Operate in 
well-ventilated area. Do not place unit on the carpet.  

• 

Do not allow the battery terminals to become shorted. 

• 

To reduce the risk of damage to the power cord, always pull by 
connector rather than the cord. 

• 

Use only the supplied adapter or optional regional and car adapter 
offered by Maha Energy. Using third party accessories voids the 
product warranty. 

FEATURES & SPECIFICATIONS 

• 

Four independent slots for AA or AAA NiMH batteries.  

• 

Backlit LCD display. 

• 

Digitally displays capacity, voltage, time and current. 

• 

Five modes of operation: Charge, Refresh & Analyze, Break-In, 
Discharge and Cycle.  

• 

19 selectable charging current from 0.2A to 2.0A. 

• 

10 selectable discharging current from 0.1A to 1.0A.  

• 

Worldwide power supply.  

Charging Current: 

Programmable from 0.2A to 2.0A in 
increments of 0.1A 
 

Topoff Charging Current: 

100mA 
 

Maintenance Charging 
Current: 

10mA 
 

Discharge Termination: 

Voltage 1.00V 
 

Discharging Current: 

Programmable from 0.1A to 1.0A in 
increments of 0.1A 
 

Capacity Storage Memory: 

12 (Cycle mode only) 

Supported Capacity*: 

100 to 20,000mAh 
 

Charger Input Power: 

12V 2.0A  
 

Adapter Input: 

100-240V 50/60Hz  
 

* Always ensure that the batteries can accept the programmed rates.  
 
 

GENERAL BATTERY EDUCATION 

 
What is 0.1C, 0.2C, etc?  

 

“C” stands for the battery capacity and the number in front of it is the 
fraction of the battery capacity. For example, 0.1C means 0.1 times the 
capacity for the battery. For a 2700mAh battery, 0.1C would be 0.1 times 
2700mAh which equals 270mA.  

 
Choosing the right charging & discharging rate 

 Charging at a rate below 0.33C and above 1.0C is not 
recommended.  

 
Charging too slow may prevent the charger from terminating correctly. 
Charging too fast may damage the battery.  

 Typically speaking, slower charging rate will yield better battery 
performance but requires longer time. Faster charging rate may not 
charge as fully and battery temperature can be higher.

 
Battery Matching 
 

In most devices, usually two or more batteries are used together. When 
batteries are used in a series, the performance is limited by the worst 
one. In other words, one poorly performing battery can significantly 
reduce the device runtime.  

 Battery matching refers to grouping batteries with similar “actual” 
capacity. To perform this, use the Refresh & Analyze mode to determine 
the battery capacity. Group batteries with capacity within about +/- 5% of 
the rated capacity.  

 
Battery “Forming” 
 

New batteries and those stored for extended period become chemically 
deactivated. Battery forming is a charge-discharge-charge cycle which 
forces a full charge into the battery at a very slow rate. This process 
activates the battery. In certain cases, it needs to be repeated two or 
three times. 

 Battery forming can be performed using the Break-In mode.  

MH-C9000 

WizardOne Charger-Analyzer 

Понравилась статья? Поделить с друзьями:
  • Инструкция logitech mx master 2s
  • Инструкция lion smile 40 ex mild
  • Инструкция lion alcolmeter sd 400
  • Инструкция ling zhi crystal blocks панда
  • Инструкция lightburn на русском языке