Инструкция по программированию dsc 1616

DSC PC1616 Installation Manual

  • Contents

  • Table of Contents

  • Troubleshooting

  • Bookmarks

Quick Links

PC1616/PC1832/PC1864 v4.7

I n s ta l l a t i o n G u i d e

WARNING: This manual contains information on limitations regarding product use and function and

information on the limitations as to liability the manufacturer. The entire manual should be carefully read.

loading

Related Manuals for DSC PC1616

Summary of Contents for DSC PC1616

  • Page 1
    PC1616/PC1832/PC1864 v4.7 I n s ta l l a t i o n G u i d e WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability the manufacturer. The entire manual should be carefully read.
  • Page 3: Table Of Contents

    Ta b l e o f C o n t e n ts Guidelines for Locating Smoke Detectors and CO Detectors ……. ii Section 1 Installation &…

  • Page 4
    Smoke alarms should be installed outside of each sleeping area and on each level of the home. DSC recommends that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be protected include: the basement;…
  • Page 5: Section 1 Installation & Wiring

    Section 1 Installation & Wiring This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1832 and PC1864 control panels. This Product is in Conformity with EMC Directive 2004/108/EC based on results using harmonized standards in accordance with article 10(5), R&TTE Directive 1999/5/EC based on Following Annex III of the directive and LVD directive 2006/…

  • Page 6
    IMPORTANT: IMPORTANT: 7 AHr 12VDC/ 7 Ah Battery 1.This equipment, Alarm Controller PC1616/1832/1864/etc. 1.This equipment, Alarm Controller PC1616/1832/1864/etc. shall be installed and used within an environment that provides shall be installed and used within an environment that provides the pollution degree max 2 and overvoltages category II the pollution degree max 2 and overvoltages category II NON HAZARDOUS LOCATIONS, indoor only.
  • Page 7: Keybus Wiring

    Section 1 Installation & Wiring 1.1 Keybus Wiring The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules. The 4 KEY- BUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel. The following rules must be followed when wiring the Keybus: •…

  • Page 8: Aux Power Wiring

    Break the wire run to provide supervision of connections. The power supervision relay has to be powered from the last detector in the loop. SEOL RESISTOR When installing wireless CO detectors, use only DSC models ZONE (5600 ohm) INPUT WS4913 and WS8913. DSC wireless receivers models…

  • Page 9: Telephone Line Wiring

    Program Section [701] Opt [7] to ON, if 14AH or 24AH battery is used. NOTE: Replace batteries every 3-5 years, If two batteries are required to meet the standby time, use DSC Enclosure Model Power UC1. Battery capacity will deteriorate with age and number of charge/ discharge cycles.

  • Page 10: Section 2 User Commands

    PowerSeries — PC1616/PC1832/PC1864 Section 2 User Commands Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent alarm functions and status. The LCD keypad displays the description and status indicator lights represent alarm functions and status. This section describes basic keypad commands.

  • Page 11
    Section 2 User Commands [][2] Trouble Display Refer to Appendix B – Troubleshooting Guide, for troubleshooting assistance and a detailed description of all trouble conditions. Press [8] in the trouble menu on any new PowerSeries keypad to enter the time and date programming menu. This option will be available if a Loss of Clock trouble is present on the system.
  • Page 12: Function Keys

    PowerSeries — PC1616/PC1832/PC1864 [][6] User Functions Press [][6] followed by the Master Code, then press the number corresponding to the following functions. Program Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Program the time using military standard (e.g., 8:00 pm = 20:00 hours).

  • Page 13: Chapter 3 Programming

    Chapter 3 Programming Chapter 3 Programming This chapter provides the information necessary to program all the features required for a basic system, as well as common applications. 3.1 Template Programming Selecting [][8] [Installer Code] [899] displays the current 5-digit template programming code. Refer to Appendix C — Template Programming for a detailed description of available templates and corresponding 5-digit codes.

  • Page 14
    PowerSeries — PC1616/PC1832/PC1864 3.3.1 Programming Toggle Options Enter the 3-digit programming section number: • The Armed light turn OFF and Keypad Type Option ON Option OFF • The Ready light turns ON Zone Light Zone Light • The keypad indicates the ON or OFF status of the toggle…
  • Page 15: Chapter 4 Programming Descriptions

    Chapter 4 Programming Descriptions Chapter 4 Programming Descriptions The following is a brief description of the features and options available in the Power PC1616/1832/1864 control panel. Please refer to the keypad installation sheet for function key programming. Global Stay Arming If enabled by the installer, when this function key is pressed the panel will prompt the user for an access code.

  • Page 16
    [009] to [011] PGM Outputs The PC1616 and PC1832 have two on-board PGM outputs (PGM1 and PGM2). The PC1864 has four on-board PGM outputs (PGM1 to PGM4). The panel has the capacity for up to 14 PGM outputs (8 additional low-current PGM outputs with PC5208 module, 4 additional high-current PGM outputs with a PC5204 module).
  • Page 17
    Chapter 4 Programming Descriptions [10] Latched System Event (Strobe): Output will activate when a selected condition occurs on any selected partition. Note output can be programmed to follow timer [11] System Tamper: Output will activate when any tamper condition is present [12] TLM and Alarm: Output will activate if a telephone line trouble is present and then an alarm occurs [13]…
  • Page 18
    PowerSeries — PC1616/PC1832/PC1864 [013] First System Option Code Option Description ON: zones require normally-closed loops. OFF: zones require End-Of-Line resistors, as determined by option [2]. ON: zones require double End-Of-Line resistors. OFF: zones require single End-Of-Line resistors. ON: keypads will display all trouble conditions while armed. OFF: keypads will only display fire trouble when armed. This option must be OFF if LCD5500 v2.x (or older) keypads are used on the system.
  • Page 19
    Chapter 4 Programming Descriptions [016] Fourth System Option Code Option Description ON: the system supervises the AC input and displays a trouble if a failure is detected. OFF: AC Input is not supervised. ON: the trouble light will flash when an AC trouble is detected. OFF: the trouble light turns on, does not flash. ON: the keypad blanks (no indicator lights) if a key is not pressed for 30 seconds.
  • Page 20
    PowerSeries — PC1616/PC1832/PC1864 [019] Seventh System Option Code Option Description For Future Use For Future Use ON: when disarming, the keypad will display only the first alarm to occur during the last arming period. OFF: when disarming, the keypad will display all zones that were in alarm during the last arming period…
  • Page 21
    Chapter 4 Programming Descriptions ON: the user cannot switch from Away Arm mode to Stay Arm mode using the function keys. OFF: the user can switch arming modes. ON: the system disconnects a listen in/two-way session if a new event occurs. OFF: the system does NOT disconnect.
  • Page 22
    PowerSeries — PC1616/PC1832/PC1864 [165] Maximum Dialing Attempts Program the Maximum Dialing Attempts before the panel will generate a Failure to Communicate (FTC) trouble condition. Valid entries are . For UL Listed installations, 5 attempts is required. [001] to [005] [166] Post Dial Wait for Handshake Program the maximum time the panel will wait, after dialing, for a valid handshake from the central station.
  • Page 23
    Chapter 4 Programming Descriptions [190] No Activity Arming Pre-Alert Duration Program the amount of time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypads will emit a steady tone, warning the user that the system is about to arm. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255]. [191] to [198] No Activity Arm Timer Program the amount of time, in minutes, for the No Activity Arm Timer ([191] for Partition 1, [192] for Partition 2, etc.).
  • Page 24
    • Module Supervisory • Fire Zones Bypassed (Zones 1-64) • Ground Fault (PC5700) • Fire Supervisory (Wireless/AML Zones 1-32) • TLM Trouble (PC1616/PC1832/PC1864, PC5700 Line 1-2) • AC Trouble (PC1616/PC1832/PC1864, PC520X) • FTC Trouble [350] Communicator Format Program the 2-digit number for the desired Communicator Format for the First Phone Number and the Second Phone Number. When dialing the Third Phone Number, the system will use the Communicator Format programmed for Phone Number 1.
  • Page 25
    Chapter 4 Programming Descriptions Delinquency Transmission Delay: Number of hours (Activity Delinquency) or days (Arming Delinquency) the panel will delay before transmit- ting the event to the central station. Valid entries: [001] to [255]. Time, in minutes, after an alarm has occurred that the system will report a Communication Cancel reporting Communication Cancel Window: event if the system is disarmed.
  • Page 26
    PowerSeries — PC1616/PC1832/PC1864 : the keypad will display the message ‘Communications Cancelled’ (programmable LCD) or ‘CC’ (fixed-message LCD) upon successful transmission of the Communication Cancelled reporting event. : the keypad will not display these messages. : the system dials the Call Waiting Cancel String on the first attempt to dial the central station.
  • Page 27
    Chapter 4 Programming Descriptions [406] Number of Rings to Answer On Program the number of consecutive rings that panel must detect to answer for downloading. Valid entries are [000] to [010]. [499] PC-Link Communications Enter the following command to initiate downloading via PC-Link: [499] [Installer Code] [499]. Plugging in the PC-Link connector will automatically initiate the connection if DLS is initiated before connecting the PC-Link Header.
  • Page 28
    PowerSeries — PC1616/PC1832/PC1864 PGM Output Option [32] Option Description For Future Use [1]-[7] : the PGM is activated for the duration programmed in PGM Output Timer. : the PGM is activated when an Opening After Alarm occurs, and will be deactivated when a valid access code is entered.
  • Page 29
    Chapter 4 Programming Descriptions [702] Second International Option Code Option Description : the communicator uses a 33/67 make/break ratio when pulse dialing. : the system uses a 40/60 make/break ratio. : the system dials regardless of the presence of a dial tone after the first attempt. : the system dials only if a dial tone is detected.
  • Page 30
    PowerSeries — PC1616/PC1832/PC1864 [903] View Module Supervision The keypad will display the modules detected by the system by turning on the associated zone light (LED keypads), flashing the numbers (fixed-message LCD keypads), or displaying the modules detected in plain language (programmable LCD keypads). Refer to the chart…
  • Page 31
    Chapter 4 Programming Descriptions [001]-[064] Label Programming, Zone 1-64 (PK5500/RFK5500/WT5500 only) Zone and other labels in these sections can be customized. Default labels are in English and do not change when an alternate language is selected. Labels can be programmed locally or downloaded/uploaded using DLS and Connect 24 interactive software. To program a zone label: Press To Enter/Display…
  • Page 32
    PowerSeries — PC1616/PC1832/PC1864 Words Table Item # Text Item # Text Item # Text Item # Text Item # Text Item # Text Aborted Control Garage Motion Shop Date Side Access Daughter’s Glass North Siren Active Degrees Goodbye Sliding Activity…
  • Page 33: Chapter 5 Programming Worksheets

    Chapter 5 Programming Worksheets Chapter 5 Programming Worksheets 5.1 Index to Programming Worksheets Programming Option Page Programming Option Page [348] Test Transmission Reporting Codes ……….44 [000] Keypad Enrollment ……………30 [349] PC5700 Maintenance Reporting Codes ………..44 [001]-[004] Zone Definitions…………..30 [350] Communicator Format Options …………44 [005] System Times …………….31 [351]-[358] Alarm/Restore Communicator Call Directions…….44 [006] Installer Code …………….31…

  • Page 34
    PowerSeries — PC1616/PC1832/PC1864 Programming Worksheets Shaded programming sections indicate minimum programming requirements. Keypad Partition /Slot and Function Key Programming [000] Keypad Enrollment This must be done at each keypad requiring programming. [0] Slot address (For the partition, 0-8; for the slot, 1-8). For example, to enroll a keypad in partition 3, slot 1, enter (31).
  • Page 35
    Chapter 5 Programming Worksheets Section Zone Def. Section Zone Def. Section Zone Def. Section Zone Def. I___I___I I___I___I I___I___I I___I___I [001] [002] [003] [004] I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I I___I___I…
  • Page 36
    [009] PGM1 and PGM2 Output Programming (Main Panel) Program PGM Option Attributes in sections [501] — [514]. Program PGM partitions in sections [551] — [564]. PC1616 and PC1832 have 2 on-board PGMs (PGM 1 and 2). PC1864 has 4 on-board PGMs (PGM 1-4). Default…
  • Page 37
    Chapter 5 Programming Worksheets [013] First System Options   Normally Closed Loops  End-of-Line Resistors  Double End-of-Line Resistors Single End-of-Line Resistors     Panel shows all Troubles when armed  Panel shows only Fire Troubles when armed …
  • Page 38
    PowerSeries — PC1616/PC1832/PC1864 [017] Fifth System Options   WLS Key Does Not use Access Codes  WLS Key Uses Access Codes   RF Jam Log after 5 Minutes  RF Jam Log after 30 Seconds   Audible RF Jam Trouble Beeps …
  • Page 39
    Chapter 5 Programming Worksheets [021] Eighth System Options   Access Code Entry Blocked During Entry Delay  Access Code Entry Not Blocked During Entry Delay   For Future Use    For Future Use    For Future Use …
  • Page 40
    PowerSeries — PC1616/PC1832/PC1864 [101]-[164] Zone Attributes Zone Attribute Defaults (Y = Option ON; N = Option OFF) Attribute: Audible Steady Chime Bypass Force* Swing Tx. Delay Wireless Zn Cross Zn Silent Pulsed Zone Type: 00 Null Zone 01 Delay 1…
  • Page 41
    Chapter 5 Programming Worksheets Attribute: Zone Attributes 10-13 For Future Use NC Loops SEOL DEOL Config. Config. Config. 20 24hr Freeze 21 24hr Latching Tamper 22 Momentary Keyswitch 23 Maintained Keyswitch 25 Interior Delay 26 24hr Non-alarm 29 Auto Verified Fire 30 Fire Supervisory 31 Day Zone 32 Instant Stay/Away…
  • Page 42: System Timers

    PowerSeries — PC1616/PC1832/PC1864 Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn Type** Silent Pulsed [135] I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I [136] I_____I I_____I I_____I I_____I I_____I I_____I I_____I I_____I…

  • Page 43
    Chapter 5 Programming Worksheets [168] Set Clock Forward (Daylight Saving Time) Def 003 Month |_______|_______|_______| Valid Entries 001-012 Def 005 Week |_______|_______|_______| Valid Entries 000-005 Def 000 |_______|_______|_______| Valid Entries 000-031 Def 001 Hour |_______|_______|_______| Valid Entries 000-023 Def 001 Increment |_______|_______|_______| Valid Entries 001-002…
  • Page 44
    Partition 8 is enabled  Disabled For the PC1864 and PC1832, the default setting is partition 1, zones 1-16 ON. For the PC1616, the default setting is par- tition 1, zones 1-6 ON. Partition 1 Zone Assignment Partition 2 Zone Assignment…
  • Page 45
    Chapter 5 Programming Worksheets Account Codes Enter a 6-digit account number for the system account code. SIA will use this account code for all eight partitions. Only SIA supports 6-digit account codes. If the last two digits of the account code are FF, the panel will only use the first four digits. Section [FFFFFF] [310] System Account Code…
  • Page 46
    PowerSeries — PC1616/PC1832/PC1864 [328] Miscellaneous Alarm Reporting Codes Duress Alarm _______ _______ Opening After Alarm _______ _______ Recent Closing _______ _______ Zone Expander Supervisory Alarm _______ _______ Zone Expander Supervisory Restore _______ _______ Cross Zone Police Code Alarm _______ _______…
  • Page 47
    Chapter 5 Programming Worksheets [338] Miscellaneous Tamper Reporting Codes General System Tamper _______ _______ General System Tamper Rest. _______ _______ Keypad Lockout _______ _______ [339]-[340] Closing (Arming) Reporting Codes, Access Codes 1-32 Section Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7…
  • Page 48
    PowerSeries — PC1616/PC1832/PC1864 [347] Miscellaneous Maintenance Reporting Codes [348] Test Transmission Reporting Codes Telephone Number 1 FTC Restore Walk Test End _________ _________ _________ _________ Telephone Number 2 FTC Restore Walk Begin _________ _________ _________ _________ Event Buffer 75% Full Since Last Upload…
  • Page 49
    Chapter 5 Programming Worksheets [367]-[374] Opening/Closing Communicator Call Directions Option 1 Option 2 Option 3 Option 4 Option 5 Options 6,7,8 Section Partition 1st Telephone 2nd Telephone Not Used Not Used Alt Comm Future Use Number (Def OFF) Number (Def OFF) (Def OFF) (Def OFF) (Def OFF)
  • Page 50
    PowerSeries — PC1616/PC1832/PC1864 [380] First Communicator Options   Communications Enabled  Communications Disabled   Restorals on Bell Time-out Restorals Follow Zones    Pulse Dialing DTMF Dialing     Switch to Pulse Dialing on 5th Attempt DTMF Dial For All Attempts …
  • Page 51
    ___| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| _ ______| [403]-[404] DLS Downloading Access Code / Panel ID Code (Enter 6 Hexadecimal Digits) Panel Default [403] Downloading Access Code [404] Panel ID Code PC1616 161600 |_______|_______|_______|_______|_______|_______| |_______|_______|_______|_______|_______|_______| PC1832 183200…
  • Page 52
    PowerSeries — PC1616/PC1832/PC1864 [23] 24-hr Silent Input (PGM2 only) [24] 24-hr Audible Input (PGM2 only) [25] Delayed Burglary & Fire Output [26] Battery Test Output [28] Holdup Output [30] Partition Status Alarm Memory Output [33] For Future Use [34] Away Armed with no Zone Bypassed Status…
  • Page 53
    Chapter 5 Programming Worksheets PGM Output Partition Assignment Section PGM Partition: 1 Main Board [551] ________ ________ ________ ________ ________ ________ ________ ________ [552] ________ ________ ________ ________ ________ ________ ________ ________ Main Board / PC5208 [553] ________ ________ ________ ________ ________ ________…
  • Page 54
    PowerSeries — PC1616/PC1832/PC1864 [605]-[608] Opening (Disarming) Reporting Codes, Access Codes 33-95 Section Code 33 Code 34 Code 35 Code 36 Code 37 Code 38 Code 39 Code 40 [605] _______ _______ _______ _______ _______ _______ _______ _______ _______ _______ _______…
  • Page 55
    Chapter 5 Programming Worksheets [695] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7 _ _ __ _ _ _ _ _ _ __ _ _ _ _ __ _ _ _ _ _ __ _ _ _ _ __ _ _ _ _ _ __ _ _ _ _ _ __ _ _ _ _ _ _ __ _ _ _ _ _…
  • Page 56: Module Programming

    PowerSeries — PC1616/PC1832/PC1864 Module Programming [801] PC5400 Printer Module Programming Refer to the PC5400 Installation Manual for installation and programming instructions. [802] PC59xx VOX Module Programming Refer to the PC59xx Installation Manual for installation and programming instructions. [804] Wireless Expansion Programming Refer to the RF5132/RFK55xx/TR5164 Installation Manual for programming locations and instructions.

  • Page 57
    Chapter 5 Programming Worksheets For the Record Customer ___________________________________________________________________________________________________________ Address ____________________________________________________________________________________________________________ Telephone ______________________________________________ Installation Date: ___________________________________________ Installer’s Code: _____________________________________________________________________________________________________ Module Name Description Location _____________________________________________________________________________________________ PC1616/PC1832/PC1864 Main Panel ________________________________ ____________________ _____________________________________________________________________________________________ ________________________________ ____________________ _____________________________________________________________________________________________ ________________________________ ____________________ _____________________________________________________________________________________________ ________________________________ ____________________ _____________________________________________________________________________________________ ________________________________…
  • Page 58
    PowerSeries — PC1616/PC1832/PC1864 Zone Programming Summary Zone programming can be found in sections [001] — [004], [101] — [164], [020], [202] — [265]. Use this area to record a summary of your zone pro- gramming. System Zone System Zone Zone Label…
  • Page 59: Appendix A: Reporting Codes

    Special Opening Opening (disarming) using one of the following methods: keyswitch, E(4)AA-000 OP-00 maintenance code, DLS software, wireless key [345]-[346] Battery Trouble/Rest. PC1616/PC1832/PC1864 battery is low/battery restored MA/R E(3)A2-000/ YT-00/YR-00 R(3)A2-000 [345]-[346] AC Line Trouble/Rest. AC power to control panel is disconnected or interrupted/AC power…

  • Page 60
    Appendix A: Reporting Codes Automatic Dialer SIA Auto Section # Reporting Code Code Sent When… Contact ID Direction* Rep Codes** Codes [345]-[346] TLM Failure/Restore Telephone line monitoring trouble/Telephone line restored MA/R E(3)51-000/ LT-01/LR-01 R(3)51-000 [345]-[346] Gen System Trouble/Rest. “Service Required” trouble (view troubles using [*][2])/trouble restored MA/R E(3)AA-000/ YX-00/YZ-00…
  • Page 61: Appendix B: Troubleshooting Guide

    PowerSeries — PC1616/PC1832/PC1864 Appendix B: Troubleshooting Guide Testing: • Power up system • Program options as required (See Programming Section) • Violate, then restore zones • Verify correct Reporting Codes are sent to the Central Station Troubleshooting: LCD Programmable-Message Keypad •…

  • Page 62
    Appendix B: Troubleshooting Guide Trouble Cause Troubleshooting Trouble [1] Service Required Press [1] to determine specific trouble [1] Low Battery Main panel battery less than 11.1VDC NOTE: If battery is new allow 1 Hr. for battery to charge. • Verify voltage measured across AC terminals is 16-18 VAC. NOTE: This trouble condition will not Replace transformer if required.
  • Page 63
    PowerSeries — PC1616/PC1832/PC1864 Trouble Cause Troubleshooting Trouble [2] AC Failure No AC at panel AC input Verify voltage measured across AC terminals is 16-18VAC. Replace terminals transformer if required. Trouble [3] Telephone Line Trouble Phone Line Voltage at TIP, RING on •…
  • Page 64
    Appendix B: Troubleshooting Guide Trouble Cause Troubleshooting Trouble [5] Zone Fault (Cont.) One or more wireless devices have not • If the trouble occurs immediately, a conflict with a hard wired checked in within the programmed time zone exists: • The zone being used is already assigned to a PC5108 zone expander •…
  • Page 65: Appendix C: Template Programming

    PowerSeries — PC1616/PC1832/PC1864 Appendix C: Template Programming Template programming allows quick programming of the minimum functions required for basic operation. The below tables are used to determine the desired template to be used ( for information on performing template programming see Section 4 – Pro- gramming Descriptions).

  • Page 66
    Appendix C: Template Programming • Digit 4 selects reporting code configurations Common Selected Openings/ Zone DLS/Installer Option Group Troubles Closings Restorals Lead In/Out                  …
  • Page 67
    PowerSeries — PC1616/PC1832/PC1864 Openings & Closings Users CLOSINGS, Residential Dial Reporting codes Section [339] 9-16 [339] 17-24 [340] 25-32 [340] 33-40 [601] Section Users OPENINGS, Residential Dial Reporting codes [342] 9-16 [342] 17-24 [343] 25-32 [343] 33-40 [605] Enable Opening/Closings call directions for Phone 2…
  • Page 68: Appendix D: Communicator Format Options

    Appendix D: Communicator Format Options Appendix D: Communicator Format Options This section requires two 2-digit entries to set the communications • If an event’s reporting code is programmed as [00] or [FF], the format that is to be used for each phone number (1 per phone number). panel will not attempt to call central station.

  • Page 69
    PowerSeries — PC1616/PC1832/PC1864 Telephone Line Monitoring (TLM) the panel receives the handshake, it will emit an alarm tone over the telephone line for 20 seconds. If several alarms occur at the same When the TLM Enable option is selected, the panel will supervise the…
  • Page 70: Safety Instructions For Service Persons

    SAFETY INSTRUCTIONS FOR SERVICE PERSONS SAFETY INSTRUCTIONS FOR SERVICE PERSONS WARNING: When using equipment connected to the telephone network, there are basic safety instructions that should always be followed. Refer to the Safety Instructions provided with this product; save them for future reference. Instruct the end-user regarding the safety precautions that shall be observed when operating this equipment.

  • Page 71: Limited Warranty

    If the laws of such a jurisdiction apply to any claim by or against DSC, the limitations and disclaimers Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot contained here shall be to the greatest extent permitted by law.

  • Page 72
    SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT. (f) Termination — Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.

Глава 3: Программирование

Эта глава содержит информацию о программировании функций системы. Полное описание программируемых функций приведено в инструкции на PC1616/1832/1864.

4.1Как программировать

DSC рекомендует заполнить таблицы программирования необходимой информацией перед программированием системы. Это поможет уменьшить время, необходимое для программирования и поможет избежать ошибок.

Для входа в режим программирования установщика введите [ ][8] и код установщика. Индикатор Program начнет мигать (на ЖКИ появится «Введи ячейку»). При вводе неправильного кода будет выдан звуковой сигнал ошибки. Нажмите [#] и введите код снова.

Заводская установка кода: 5555

Индикаторы Armed и Ready показывают статус режима программирования

Индикатор Armed включен

Ожидание ввода 3 цифр номера ячейки программирования

В режиме программирования модуля, ожидание ввода номера ячейки модуля

Индикатор Ready включен

Ожидание ввода данных в ячейку программирования

Индикатор Ready мигает

Ожидание ввода шестнадцатеричных данных

Режим программирования недоступен, если любой из разделов на охране или в режиме тревоги.

4.2Программирование переключаемых опций

Введите три цифры номера ячейки программирования

Пульт

Опция ВКЛ

Опция ВЫКЛ

Индикатор Armed выключится

С индикаторами зон

Инд. Зоны вкл

Инд. Зоны выкл

Включится индикатор Ready

ЖКИ символьный

№ включен

№ выключен

Пульт покажет, какие опции включены, какие выключены

ЖКИ текстовый

№ отображается

Отображается —

Для переключения опций нажимайте кнопку с

соответствующим номером. Пульт отобразит статус опции.

− После установки всех опций в нужное состояние нажмите [#] для выхода из ячейки программирования. − Индикатор Ready выключится, индикатор Armed включится.

4.3 Программирование десятичных и шестнадцатеричных данных

− Введите три цифры номера ячейки программирования

− Индикатор Armed выключится, включится индикатор Ready − Введите данные из таблиц программирования

Для ячеек, требующих ввода 2 или 3 чисел, пульт выдает двойной сигнал после ввода каждого числа и переходит к ожиданию следующего. После ввода последнего числа пульт выдает 5 коротких сигналов и выходит из ячейки программирования. Индикатор Ready выключается и включается индикатор Armed.

Для ячеек, в которые не требуется ввод всех чисел, вы можете нажать [#] после ввода необходимых данных. Индикатор Ready выключается и включается индикатор Armed.

Вы можете нажать [#] в любое время, панель выйдет из ячейки программирования, сохранив все введенные данные.

Иногда требуется ввод шестнадцатеричных данных. Для ввода HEX чисел, нажмите [ ] перед вводом цифры. Индикатор Ready начнет мигать. Смотрите таблицу ввода шестнадцатеричных чисел. После ввода цифры, индикатор Ready продолжает мигать. Нажмите [ ] еще раз для перехода в десятичное программирование. Индикатор Ready включится.

Шестнадцатеричные цифры могут использоваться в номере телефона. Значение см. в таблице.

Значение

Ввод

Значение в телефоне

HEX [A]

Нажмите [ ][1][ ]

Не используется

HEX [B]

Нажмите [ ][2][ ]

Имитация кнопки [ ]

HEX [C]

Нажмите [ ][3][ ]

Имитация кнопки [#]

HEX [D]

Нажмите [ ][4][ ]

Ожидание гудка

HEX [E]

Нажмите [ ][5][ ]

Пауза 2 секунды

HEX [F]

Нажмите [ ][6][ ]

Конец номера телефона

4.4Как выйти из режима программирования установщика

Для выхода из режима программирования, нажмите [#], когда панель ожидает ввода номера ячейки программирования (индикатор

Armed включен).

PC1616/PC1832/PC1864 STANDARD INSTALLATION GUIDE

This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, 
PC1832 and PC1864 control panels.  

This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual 

which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.

NOTE: All necessary information required to meet UL Listing requirements is contained in this document.

Read the complete guide, then work through each step as indicated.

FEATURES

PC1616

PC1832

PC1864

OUT Of THE BOX

On-board Zones

8

8

Qty 1 

Qty 1 

Qty 1 

Qty 1 

Qty 2 

Qty 1

Qty 4 

Qty 16 

Qty 1

Qty 1

Qty 1 

Qty 1 

Cabinet
PC Module
Installation guide
User manual
Cabinet Label
Cabinet Door Plug
Standoffs
5.6K

Ω Resistors

2.2K

Ω Resistors

1.0K

Ω Resistors

10

Ω Resistors

Grounding Kit

Hardwired Zones

16 (1xPC5108)

32(3xPC5108)

64 (7xPC5108)

Wireless Zones

16

32

32

Keypad Zone Support

On-board PGM Outputs

PGM 1 — 50mA
PGM 2 — 300mA

PGM 1 — 50mA
PGM 2 — 300mA

PGM 1, 3, 4 — 50mA
PGM 2 — 300mA

PGM Expansion

8x50mA (PC5208)
4×500 mA (PC5204)

8x50mA (PC5208)
4×500 mA (PC5204)

8x50mA (PC5208)
4×500 mA (PC5204)

Keypads

8

8

8

Partitions

2

4

8

SPECIFICATIONS

Temp Range ……. 0°C-49°C (32°F-120°F)
Humidity (Max)……………………… 93%R.H.
Power Supply…….. 16.5V

AC

/40VA @60Hz

Current Draw (Panel) ………110mA (nom.)
Aux+ Output…………11.1-12.6V

DC

/700mA

Bell Output …………..11.1-12.6V

DC

/700mA

User Codes

32 + Master Codes

32 + Master Codes

32 + Master Codes

Event Buffer

500 Events

500 Events

500 Events

Transformer Required

16.5V

AC

/40VA

16.5V

AC

/40VA

16.5V

AC

/40VA

Battery Required

4Ah / 7Ah/14AHr

4Ah / 7Ah/14AHr

4Ah / 7Ah/14AHr

Bell Output

12V/700 mA (cont)

12V/700 mA (cont)

12V/700 mA (cont)

COMPATIBLE DEVICES

Keypads (

Backward compatible with all PowerSeries keypads)

Modules

PK5500 Keypad…………………………………………………..125mA (max.)
PK5501 Keypad…………………………………………………..125mA (max.)
PK5508 LED Keypad……………………………………………125mA (max.)
PK5516 LED Keypad……………………………………………125mA (max.)
PC5532Z LED Keypad …………………………………………125mA (max.)
LCD5511 Fixed Message LCD Keypad…………………… 85mA (max.)
LED5511Z 8-zone LED Keypad  ……………………………100mA (max.)

Cabinets

PC5003C ………………………………. 222x298x78mm (11.3×11.7×3.0in)
PC500C ………………………………….. 213x235x78mm (8.4×9.25×3.0in)

Refer to the Reference Manual for alternate control cabinets

T-Link TL-250/TL300 ……………………………………………….275/350mA
PC5100 2-wire Interface ………… 40mA plus devices to 170mA max.
PC5132-433 Wireless Receiver ………………………………………125mA
RF5108-433 Wireless Receiver  ………………………………………125mA
PC5108 Zone Expander  ………………………………………………….30mA
PC5204 Power Supply with 4 Programmable Outputs  …………30mA
PC5208 Low Current Programmable Output Module  …………..50mA
PC5400 Printer/DVAC Module ………………………………………….65mA
PC5401 Bi-Directional RS232 Module (Not UL Listed) …………65mA
Escort5580 Telephone Interface Module ………………………….130mA

Refer to the Reference Manual for additional devices.

Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)

2 9 0 0 7 1 0 9 R0 0 3

PC1616 / PC1832 / PC1864

This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.

Reference Manual

PC1616/PC1832/PC1864 v4.1

DLS2002 and higher

WWW.DIYALARMFORUM.COM

Table of Contents

Section 1: Introduction

1

1.1 About the PC1616/PC1832/PC1864 System . . . . . . .

1

1.2About the PC1616/PC1832/PC1864 Manual Set . . . . 1

Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Programming Worksheets . . . . . . . . . . . . . . . . . . . . . . 1

User Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3Control and Indicating Equipment Specifications . . . . 1

Zone Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Access Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warning Device output . . . . . . . . . . . . . . . . . . . . . . . . . 2 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Programmable Outputs (PGMs) . . . . . . . . . . . . . . . . . . 2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operating Environmental Conditions . . . . . . . . . . . . . . 2 Keypad Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 2 Alarm Transmitter Equipment (ATE) Specification . . . . 2 System Supervision Features. . . . . . . . . . . . . . . . . . . . 2 False Alarm Prevention Features . . . . . . . . . . . . . . . . . 2 Additional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.4 Additional Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PC5100 2-Wire Addressable Interface Module . . . . . . 3

PC5108 Eight Zone Expander Module . . . . . . . . . . . . . 3

PC5132 Wireless Receiver Module . . . . . . . . . . . . . . . 3

PC5200 Power Supply Output Module . . . . . . . . . . . . . 3

PC5204 Power Supply Output Module . . . . . . . . . . . . . 3

PC5208 Eight Low Current Output Module . . . . . . . . . 3

Escort5580(TC) Module . . . . . . . . . . . . . . . . . . . . . . . . 3

PC5900 Audio Verification Module . . . . . . . . . . . . . . . . 3

PC5400 Printer Module . . . . . . . . . . . . . . . . . . . . . . . . 3

PC5401 Serial Interface Module. . . . . . . . . . . . . . . . . . 3

T-Link Local Area Network Communicator . . . . . . . . . . 3

TL250/TL300 Intranet/Internet Communicators . . . . . . 3

Alternate Communicators . . . . . . . . . . . . . . . . . . . . . . . 3

PC5700/PC5720 Fire Module. . . . . . . . . . . . . . . . . . . . 4

Enclosures/Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 Battery Standby Times versus AUX Load . . . . . . . . . . 4

Section 2: Installation and Wiring

5

2.1 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Terminal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . 5

AC Power Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Battery Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Auxiliary Power Terminals — AUX+ and GND . . . . . . . . 5 Bell Output Terminals — BELL+ and BELL- . . . . . . . . . . 5 Keybus Terminals — RED, BLK, YEL, GRN. . . . . . . . . . 6 Programmable Outputs — PGM1 to PGM4 . . . . . . . . . . 6 Zone Input Terminals — Z1 to Z8 . . . . . . . . . . . . . . . . . . 6 Telephone Connection Terminals — TIP,RING,T-1,R-1. 6

2.3 Wire Routing for Power & Non-Power Limited . . . . . . . 6

2.4 Keybus Operation and Wiring . . . . . . . . . . . . . . . . . . . 6

2.5 Current Ratings — Modules & Accessories . . . . . . . . . .6

PC1616/PC1832/PC1864 Device Ratings. . . . . . . . . . 7

System Output Ratings . . . . . . . . . . . . . . . . . . . . . . . . 7

2.6 Assigning Zones to Zone Expanders . . . . . . . . . . . . . .7

2.7 Keypad Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . .7

How to Assign Keypads. . . . . . . . . . . . . . . . . . . . . . . . 7 Function Key Programming . . . . . . . . . . . . . . . . . . . . . 8

2.8 Confirming Module Supervision . . . . . . . . . . . . . . . . . .8

2.9 Removing Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2.10 Zone Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Burglary Zone Wiring Chart . . . . . . . . . . . . . . . . . . . . . 8 Normally Closed (NC) Loops . . . . . . . . . . . . . . . . . . . . 8 Single End Of Line (EOL) Resistors . . . . . . . . . . . . . . 9 Double End of Line (DEOL) Resistors . . . . . . . . . . . . . 9 Fire Zone Wiring — 4-wire Smoke Detectors. . . . . . . . . 9 Compatible 4-Wire Smoke Detectors . . . . . . . . . . . . . 9 Fire Zone Wiring — 2-wire Smoke Detectors. . . . . . . . . 9 Compatible 2-Wire Smoke Detectors . . . . . . . . . . . . 10 2-Wire Smoke Detector Initating Circuit. . . . . . . . . . . 10 Keyswitch Zone Wiring . . . . . . . . . . . . . . . . . . . . . . . 10

2.11 Keypad Zone/PGM . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Assigning Keypad Zones. . . . . . . . . . . . . . . . . . . . . . 10

2.12 Zone Activity Log . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Section 3: How to Program

11

3.1 How to Enter Installer Programming . . . . . . . . . . . . . .11

LED Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

LCD Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2 Programming Decimal Data . . . . . . . . . . . . . . . . . . . .11

3.3 Programming Hexadecimal Data . . . . . . . . . . . . . . . .11

3.4 Programming Toggle Options . . . . . . . . . . . . . . . . . . .11

3.5 Viewing Programming . . . . . . . . . . . . . . . . . . . . . . . . .11

LED and ICON Keypads . . . . . . . . . . . . . . . . . . . . . . 11

LCD Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Section 4: Keypad Commands

12

4.1 Arming and Disarming . . . . . . . . . . . . . . . . . . . . . . .

.12

Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stay and Away Arming . . . . . . . . . . . . . . . . . . . . . . . 12

Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Disarming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Event Buffer (Event Log) . . . . . . . . . . . . . . . . . . . . . . 13

Viewing the Event Buffer . . . . . . . . . . . . . . . . . . . . . . 13

4.2 [*] Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

[*][1] Zone Bypassing. . . . . . . . . . . . . . . . . . . . . . . . . 13 [*][2] Trouble Display . . . . . . . . . . . . . . . . . . . . . . . . . 13 [*][3] Alarm Memory . . . . . . . . . . . . . . . . . . . . . . . . . . 14 [*][4] Door Chime On/Off . . . . . . . . . . . . . . . . . . . . . . 14 [*][5] Programming Access Codes. . . . . . . . . . . . . . . 14

WWW.DIYALARMFORUM.COM

i

Installer’s Programming — Codes and Options . . . . . 15 [*][6] User Functions . . . . . . . . . . . . . . . . . . . . . . . . . 16 LCD Keypad User Functions . . . . . . . . . . . . . . . . . . 16 [*][7] Command Output Functions . . . . . . . . . . . . . . 16 [*][8] Installer Programming . . . . . . . . . . . . . . . . . . . 16 [*][9] Arming Without Entry Delay . . . . . . . . . . . . . . . 16 [*][0] Quick Arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 [*][0] Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.3 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.4 Global and Partition Keypad Operation . . . . . . . . . . . 18

4.5 Keypad Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Automatic Scrolling of Open Zones . . . . . . . . . . . . . 18

Automatic Scrolling of Alarms in Memory . . . . . . . . . 18

24 Hour Time Display Option . . . . . . . . . . . . . . . . . . 18

Keypad Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Viewing Troubles While Armed. . . . . . . . . . . . . . . . . 18

Backlighting Boost . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Section 5: Programming Sections

19

5.1 Keypad Programming . . . . . . . . . . . . . . . . . . . . . . . . 19

5.2 Basic Programming . . . . . . . . . . . . . . . . . . . . . . . . . . 19

[001]-[004] — Zone Definitions . . . . . . . . . . . . . . . . . . 19

[005] — System Times . . . . . . . . . . . . . . . . . . . . . . . . 21

[006] — Installer’s Code . . . . . . . . . . . . . . . . . . . . . . . 21

I[007] — Master Code . . . . . . . . . . . . . . . . . . . . . . . . . 21

[008] — Maintenance Code/Guard Code . . . . . . . . . . 21

[009]-[011] — Programmable Output Options. . . . . . . 21

[012] — Keypad Lockout Options . . . . . . . . . . . . . . . . 24

[013] — First System Option Codes . . . . . . . . . . . . . . 24

[014] — Second System Option Codes . . . . . . . . . . . 25

[015] — Third System Option Codes . . . . . . . . . . . . . 26

[016] — Fourth System Option Codes . . . . . . . . . . . . 27

[017] — Fifth System Option Codes . . . . . . . . . . . . . . 27

[018] — Sixth System Option Codes. . . . . . . . . . . . . . 28

[019] — Seventh System Option Codes . . . . . . . . . . . 29

[020] — Keypad Zone Assignment . . . . . . . . . . . . . . . 30

[021] — Eighth System Option Codes . . . . . . . . . . . . 30

[023] — Tenth System Option Codes . . . . . . . . . . . . . 32

[030] — Fast Loop Response . . . . . . . . . . . . . . . . . . . 33

5.3 Advanced Programming . . . . . . . . . . . . . . . . . . . . . . 33

[101]-[164] — Zone Attributes . . . . . . . . . . . . . . . . . . . 33 [165] — Maximum Dialing Attempts . . . . . . . . . . . . . . 33 [166] — Post Dial Wait For Handshake . . . . . . . . . . . 33 [167] — T-Link Communications Wait for Acknowledge Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 [168]-[169] — Daylight Saving Time . . . . . . . . . . . . . . 33 [170] — PGM Output Timer . . . . . . . . . . . . . . . . . . . . 34 [171] — Tamper PGM Output Timer . . . . . . . . . . . . . 34 [172] — Settle Delay Timer . . . . . . . . . . . . . . . . . . . . . 34 [173] — Bell Delay Timer . . . . . . . . . . . . . . . . . . . . . . 34 [175] — Auto-arm Postpone Timer . . . . . . . . . . . . . . . 34 [176] — Cross Zone/Police Code Timer . . . . . . . . . . . 34 [178] — For Future Use . . . . . . . . . . . . . . . . . . . . . . . 34 [181]-[188] — Auto-arm Schedules. . . . . . . . . . . . . . . 34 [190] — No Activity Arming Pre-Alert Duration . . . . . . 34 [191]-[198] — No-Activity Timer (Partition 1-8) . . . . . . 35 [199] — Auto-arming Pre-Alert Time. . . . . . . . . . . . . . 35

5.4 Partition & Zone Programming . . . . . . . . . . . . . . . . .

35

[201] — Partition Selection Mask . . . . . . . . . . . . . . . . 35

[202]-[265] — Partition Zone Assignments . . . . . . . . . 35

Partitions and Zone Assignment . . . . . . . . . . . . . . . . 35

5.5 Communicator Programming . . . . . . . . . . . . . . . . . . 35

Communicator — Telephone Numbers . . . . . . . . . . . . 35 [301] — First Telephone Number. . . . . . . . . . . . . . . . . 35 [302] — Second Telephone Number . . . . . . . . . . . . . . 35 [303] — Third Telephone Number . . . . . . . . . . . . . . . . 35 [304] — Call Waiting Cancel Dialing String . . . . . . . . . 35 Communicator — Account Codes . . . . . . . . . . . . . . . . 36 [310] — System Account Code . . . . . . . . . . . . . . . . . . 36 [311]-[318] — Partition 1-8 Account Codes . . . . . . . . . 36 Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Communicator — Reporting Codes . . . . . . . . . . . . . . . 36 [320]-[323] — Alarm Reporting Codes, Zones 1 to 64 . 36 [324]-[327] — Alarm Restoral Reporting Codes,

Zones 1 to 64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 [328] — Miscellaneous Alarm Reporting Codes . . . . . 36 [329] — Priority Alarm/Restoral Reporting Codes . . . . 36 [330]-[333] — Tamper Reporting Codes, Zones 1 to 64 36 [334]-[337] — Tamper Reporting Codes, Zones 1 to 64 37 [338] — Miscellaneous Tamper Reporting Codes . . . . 37 [339]-[340] — Closing (Arming) Reporting Codes,

Zones 1-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 [341] — Miscellaneous Closing (Arming) Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 [342]-[343] — Opening (Disarming) Reporting Codes Access Codes 1 to 32 . . . . . . . . . . . . . . . . . . . . . . . . 37 [344] — Miscellaneous Opening (Disarming) Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 [345] — Maintenance Alarm Reporting Codes. . . . . . . 37 [346] — Maintenance Alarm Reporting Codes. . . . . . . 37 [347] — Miscellaneous Maintenance Reporting Codes 38 [348] — Test Transmission Reporting Codes . . . . . . . 38 [349] — PC5700 Maintenance Reporting Codes . . . . . 38 [350] — Communicator Format Options . . . . . . . . . . . 38 Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Contact ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 SIA (Level 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Residential Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Private Line Format . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Pager Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Pulse Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Scantronics Format . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Robofon Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 200 Baud FSK (CESA) . . . . . . . . . . . . . . . . . . . . . . . 40 Telephone Line Monitoring (TLM) . . . . . . . . . . . . . . . 41 [351]-[376] — Communicator Call Directions. . . . . . . . 41 [377] — Communication Variables. . . . . . . . . . . . . . . . 41 [378] — Test Transmission Time of Day . . . . . . . . . . . 42 [379] — Periodic DLS Time of Day . . . . . . . . . . . . . . . 42 [380] — First Communicator Option Codes . . . . . . . . . 42 [381] — Second Communicator Option Codes . . . . . . 43 [382] — Third Communicator Option Codes . . . . . . . . 44

5.6 Downloading Options . . . . . . . . . . . . . . . . . . . . . . . . 45

Downloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 [401] — First Downloading Option Codes . . . . . . . . . . 45 [402] — Downloading Computer’s Phone Number . . . 46 [403] — Downloading Access Code. . . . . . . . . . . . . . . 46 [404] — Panel Identification Code . . . . . . . . . . . . . . . . 46 [405] — Double-Call Timer. . . . . . . . . . . . . . . . . . . . . . 46 [406] — Number of Rings to Answer On . . . . . . . . . . . 46 [499] — Initiate PC-Link Communications . . . . . . . . . . 46

WWW.DIYALARMFORUM.COM

ii

5.7 Programmable Output Programming . . . . . . . . . . . . 46

[501]-[514] — Programmable Output Attributes . . . . . . 46 Assigning Partitions to Programmable Outputs . . . . . 46 [551]-[564] — PGM Partition Assignment. . . . . . . . . . . 47

5.8 International Programming . . . . . . . . . . . . . . . . . . . . 47

[700] — Automatic Clock Adjust . . . . . . . . . . . . . . . . . . 47

[701] — First International Option Codes . . . . . . . . . . . 48

[702] — Second International Option Codes . . . . . . . . 48

[703] — Delay Between Dialing Attempts. . . . . . . . . . . 49

5.9 Module Programming . . . . . . . . . . . . . . . . . . . . . . . . 49

5.10 Special Installer Instructions . . . . . . . . . . . . . . . . . . . 49

[900] — Panel Version . . . . . . . . . . . . . . . . . . . . . . . . . 49 [901] — Installer Walk Test Mode Enable / Disable . . . 49 [902] — Reset Module Supervision . . . . . . . . . . . . . . . 49 [903] — Module Supervision Field . . . . . . . . . . . . . . . . 49 [904] — Module Placement Test . . . . . . . . . . . . . . . . . 50 [906] — For Future Use . . . . . . . . . . . . . . . . . . . . . . . . 50 [989][Installer Code] — Default Master Code . . . . . . . . 50 [990][Installer Code] — Installer Lockout Enable . . . . . 50 [991][Installer Code] — Installer Lockout Disable. . . . . 50 [993]-[999] — Factory Defaults. . . . . . . . . . . . . . . . . . . 50 [993][Installer Code] — Restore Alternate Comm.

Factory Default Programming . . . . . . . . . . . . . . . . . . 50 [995][Installer Code] — Restore ESCORT5580(TC) Factory Default Programming . . . . . . . . . . . . . . . . . . 50 [996][Installer Code] — Restore PC5132 Wireless Factory Default Programming . . . . . . . . . . . . . . . . . . 50 [997][Installer Code] — Restore PC5400 Factory

Default Programming . . . . . . . . . . . . . . . . . . . . . . . . . 50 [998][Installer Code] — Restore PC5900 Factory

Default Programming . . . . . . . . . . . . . . . . . . . . . . . . . 50 [999][Installer Code] — Restore Factory Default Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Section 6: Fire Monitoring

51

6.1 Partitions and Fire System Configuration . . . . . . . . . .51

Fire Configuration 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Fire Configuration 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 51

6.2 Fire Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Standard Fire Operation . . . . . . . . . . . . . . . . . . . . . . 51

Auto Verify Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Four-Wire Smoke Detector Zones. . . . . . . . . . . . . . . 51

Two-Wire Smoke Detector Zones . . . . . . . . . . . . . . . 52

Fire Supervisory Zone . . . . . . . . . . . . . . . . . . . . . . . . 52

6.3 Fire System Operation . . . . . . . . . . . . . . . . . . . . . . . .52

Manual Signal Silence . . . . . . . . . . . . . . . . . . . . . . . . 52

Automatic Signal Silence (Bell Time-out) . . . . . . . . . 52

Manual Sensor Reset ([*][7][2]) . . . . . . . . . . . . . . . . . 52

Subsequent Alarm Operation . . . . . . . . . . . . . . . . . . 52

Auto-Scroll LCD Keypad Display. . . . . . . . . . . . . . . . 52

Fire Trouble Conditions . . . . . . . . . . . . . . . . . . . . . . . 52

AC Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Fire Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . 53

Section 7: Listing Requirements

54

7.1UL Listed Commercial and Residential Installations .54

Appendix A: Reporting Codes . . . . . . . . . . . . . . . . . . . . . .56

Contact ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 SIA Format — Level 2 (Hardcoded). . . . . . . . . . . . . . . 56 Contact ID Zone Alarm/Restoral Event Codes . . . . . 57 SIA Format Automatic Zone Alarm/Restoral Codes . 57

Appendix B: Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . .58

B.1 PC1616/PC1832/PC1864 UL/ULC Wiring Diagram . . . . .58 B.2 PC1616/PC1832/PC1864 Standard Wiring Diagram . . . .59 B.3 PC1616/PC1832/PC1864 European Wiring Diagram . . . .60 B.4 PC1616/PC1832/PC1864 and PC5700 Fire Module Communications Connections . . . . . . . . . . . . . . . . . . . . . . .61 B.5 Sensor Reset for 2-Wire Smoke Detectors . . . . . . . . . . . .61 B.6 Sensor Reset for 4-wire Smoke Detectors . . . . . . . . . . . .61 B.7 Other PGM Connections . . . . . . . . . . . . . . . . . . . . . . . . .61

The below symbols are used to indicate features that are only available in a particular market. No symbol indicates the feature is available for all markets.

EN

IMQ

CP-01

UK

C

Europe

Italy

United States

United Kingdom

Scandinavia

WWW.DIYALARMFORUM.COM

iii

Section 1: Introduction

1.1 About the PC1616/PC1832/PC1864 System

This product is in conformity with EMC Directive 89/336/EEC based on results using harmonized standards in accordance with article 10(5), R&TTE Directive 1999/5/EC based on following Annex III of the directive and LVD Directive 73/23/EEC as amended by 93/68/EEC based on results using harmonized standards.

This product meets the requirements of Class II, Grade 2 equipment as per EN 50131-1:2004 Standard. This product is suitable for use in systems with the following notification options:

A (use of two warning devices and internal dialer required),

B (self powered warning device and internal dialer required),

D (use of DSC model T-Link TL250 encrypted Ethernet communicator required).

The PC1616/PC1832/PC1864 are high end security systems. Below are the list of features for each panel:

PC1616

PC1832

PC1864

On-board Zones

6

8

8

Hardwired Zones

16 (1xPC5108)

32(3xPC5108)

64 (7xPC5108)

Wireless Zones

16

32

32

Keypad Zone

8

8

8

Support

On-board PGM

PGM 1 — 50mA

PGM 1 — 50mA

PGM 1/3/4 — 50mA

Outputs

PGM 2 — 300mA

PGM 2 — 300mA

PGM 2 — 300mA

Additional PGM

PC5208 8x50mA

PC5208 8x50mA

PC5208 8x50mA

Outputs

PC5204 4x500mA

PC5204 4x500mA

PC5204 4x500mA

Keypads

8

8

8

Partitions

2

4

8

User Codes

32 + Master Codes

32 + Master Codes

32 + Master Codes

Event Buffer

500 Events

500 Events

500 Events

Transformer

16.5VAC

16.5VAC

16.5VAC

Required

40VA

40VA

40VA

Battery Required

4Ah / 7Ah / 14Ah

4Ah / 7Ah / 14Ah

4Ah / 7Ah / 14Ah

Bell Output

12V 700 mA

12V 700 mA

12V 700 mA

(continuous)

(continuous)

(continuous)

The LCD keypad guides users through their available options with easy-to-understand prompts.

The status of the PC1616/PC1832/PC1864 system can be monitored over telephone lines, or using an alternative communicating device, including Skyroute™, T-LINK, GS-3050 and DVACS.

You can program the PC1616/PC1832/PC1864 using any system keypad, or using DLS downloading software and a computer (see section 3, ‘How to Program’).

Review the complete manual set before installing the PC1616/PC1832/PC1864 security system.

1.2About the PC1616/PC1832/PC1864 Manual Set

Reference Manual

This manual provides:

An overview of the system (Section 1: “Introduction”)

How to install and wire the system and its modules (Section 2: “Installation and Wiring”)

How to program the system (Section 3: “How to Program”)

An introduction to the user interface and keypad operation (Section 4: “Keypad Commands”)

An overview of the main system programming sections (Section 5: “Programming Sections”).

Installation Guide

The Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1832 and PC1864 control panels.

Programming Worksheets

The Programming Worksheets provid a detailed list of all programming sections available in the panel and a place to record your programming. Be sure to record all your system programming in the Programming Worksheets. If adding modules to your PowerSeries Control Panel, refer to the

Installation Instructions that come with each module.

User Guide

One user guide comes with the PC1616/PC1832/PC1864 system. The User’s Guide provides easy to follow instructions for end users. Installers should also review this manual, in order to properly instruct the end-users once the installation is complete.

1.3Control and Indicating Equipment Specifications

Zone Configuration

6 Fully programmable zones (PC1616)

8 Fully programmable zones (PC1832/PC1864)

34 zone types, 9 programmable zone attributes

Zone configurations available: Normally closed, Single EOL and Double EOL zone supervision

Hardwired zone expansion (fully supervised) available using the Model PC5108 (eight Zone Expander Module) and the Model PC5700 (Fire Module)

Expandable to 16 zones (PC1616)

Expandable to 32 zones (PC1832)

Expandable to 64 zones (PC1864)

One zone input available on the keypads

Wireless zone expansion (fully supervised) available using the Model PC5132 (RF Receiver, operating at 433MHz)

NOTE: PC1616 expandable to 16 zones only.

Up to 2 partitions (PC1616)

Up to 4 partitions (PC1832)

Up to 8 partitions (PC1864)

Access Codes

39 access codes:

32 User Codes (Level 2)

1 System Master Code (Level 3)

2 Supervisor Codes

2 Duress Codes

1 Maintenance/Guard Code

1 Installer Code (Level 3)

Programmable attributes for each user code (see section 4.2 for details)

1,000,000 access code variations (using 6-digit codes)

Duress codes derived from user codes plus 1 digit are not allowed

Warning Device output

Rated 12VDC, 700mA, (current limit 2.0A) supervised (EOL resistor shall be used)

Programmable as steady, pulsed or temporal three (as per ISO 8201) output

Fire alarm notification has priority over burglary alarm notification

Memory

CMOS EEPROM memory

Retains programming and system status on AC and battery failure

Data Retention: 200 years min.

Programmable Outputs (PGMs)

Up to 14 programmable outputs (PGM) with 21 options

PGM outputs are open collector type and switched to ground

Three low current (50mA) PGM outputs on main panel (PGM1, PGM3, PGM4)

NOTE: PGM3 and PGM4 available on PC1864 only.

One high current (300mA) output with 2-wire smoke detector capability on the main control board (PGM2)

Eight additional low current outputs (50mA) available using the Model PC5208

Four high current outputs (1A) available using the Model PC5204 (one configurable as a supervised bell output)

Power Supply

1.5A regulated (1.7A for UL/ULC), supervised and integral to the control unit

Type A as per EN50131-6 Standard

Input ratings: 120V, 60Hz Class II (220V-240Vac, 50/ 60Hz, 200mA for European installations)

Transformer required, mounted in the same enclosure, permanently connected for European installations

Transformer secondary ratings: 16.5Vac, 40VA min

AUX Output Voltage: 12VDC, -15%/+10% when AC Input Voltage is 85% to +110% of rated value and output current is 500mA (700mA for UL/ULC) (550mA for IMQ)

Output ripple voltage: 270mVp-p max.

Storage device: Rechargeable battery, rated 12VDC

Battery capacity: 4Ah, 7Ah, 14Ah (2 x 7Ah) or 24 Ah (2 x 12Ah)

Battery = One 12V 4Ah battery (For burglary applications)

Battery = Two 12V 7Ah (min.) rechargeable sealed lead acid for 24-hr backup (For fire monitoring applications)

Maximum standby time 24Ah (when using 14Ah battery capacity and AUX current limited to 480mA max.).

Recharging time 48h

Programmable recharging current: Low 400mA, High 700mA

Low battery trouble indication threshold 11.5VDC

Battery deep discharge protection (cut-off at 9.5VDC)

Main board current draw: 85mA (set and unset state)

Resettable fuses (PTC) used on circuit board instead of replaceable fuses

Supervision for loss of primary power source (AC Fail), battery fail or battery low voltage (Battery Trouble) with indication provided on the keypad

Internal clock locked to AC power frequency

Operating Environmental Conditions

Temperature range: -10°C to +55°C (14°F to 131°F)

Relative humidity: 93% non condensing

Keypad Specifications

Each keypad has 5 fully programmable function keys (see Section [000] in the programming section.

“T” version keypads have tamper protection

Connect up to 8 keypads

Four wire (Quad) connection to Keybus

Built in piezoelectric buzzer

Alarm Transmitter Equipment (ATE) Specification

Digital dialer integral to the main control board

Complies with TS103 021-1, -2, -3 Telecom equipment requirements

Supports the following communications formats:

10 BPS/20 BPS

DTMF Contact ID

SIA FSK

Pager

Residential Dial

Private Line

Scantronics 4-8-1

Robofon

CESA 200

Split reporting of selected transmissions to each telephone number

3 programmable telephone numbers

1 system account number

Upto 8 partition account numbers

Supports Skyroute™ Cellemetry Communication Transceiver

GS3050 GSM Universal Wireless Alarm Communicator

DTMF and pulse dialing

DPDT line seizure

Anti-jam detection

Event-initiated personal paging

T-Link/T-Link TL250/T-Link TL300 Ethernet Communications (using PC-Link) for Intranet/Internet connectivity.

System Supervision Features

The PC1616/PC1832/PC1864 continuously monitors a number of possible trouble conditions and provides audible and visual indication at the keypad. Multiple signals are indicated using scroll buttons on the LCD keypads (no priority assigned) or by different lights on the LED’s keypads. Trouble Conditions include:

AC Power Failure

Low Battery Condition

AUX Power Supply Fault

Bell Output Trouble

Telephone Line Trouble

Failure to Communicate

Loss of Internal Clock

Module Fault (Supervisory or Tamper)

Trouble by Zone

Fire Trouble

Tamper by Zone

False Alarm Prevention Features

Audible Exit Delay

Audible Exit Fault

Urgency on Entry Delay

Quick Exit

Swinger Shutdown

Recent Closing Reporting Code

Cross Zone/Police Code Alarm

Burglary-Verified Timer

Communication Delay

Rotating Keypress Buffer

Additional Features

Automatic inhibit (swinger shutdown) for Alarm, Tamper, Trouble signals after 3 occurrences in a given set period

(see section [377]), Opt [1] alarms, [2] tampers, [3] troubles.

Programmable keypad lockout option (see section [012])

Automatic arming by partition at a specified time, each day of the week

No activity arming

Keypad activated alarm output and communicator test

Keypad lockout

Audio capability using the PC5900 Audio Verification Module and central station 2-way listen-in

All modules connect to the system via a 4-wire Keybus, up to 1000’/305m from the main panel

Event buffer can be printed using PC5400/PC5401 RS232 Serial Interface module

Supports the Escort5580(TC) Voice Prompt Module, with automation and lighting control

500 event buffer, time and date stamped

Uploading/downloading capability

Daylight savings time option

1.4Additional Devices

If a Fault or Tamper condition occurs on a zone while the system is disarmed, a trouble condition will be indicated. If a Fault or Tamper condition occurs on a zone while the system is armed, the bell will be sounded. This applies to zones and zone expander modules, and cannot be changed. This feature will be active for the following modules:

PC5108

PC5700

PC5132

PK55XX with a zone programmed

RFK55XX with a zone programmed

Keypads

A maximum of 8 keypads can be connected to the control panel. You can connect any combination of the following listed.

PK5500/RFK5500 LCD keypad

PK5501/RFK5501 ICON keypad

PK5508/RFK5508 8 Zone LED keypad

PK5516/RFK5516 16 Zone LED keypad

LCD5511 Fixed Message LCD keypad

LED5511Z 8 Zone LED keypad

PC5508Z 8 Zone LED keypad

PC5532Z 32 Zone LED keypad

PC5516Z 16 Zone LED keypad

LCD5500Z Liquid Crystal Display (LCD) keypad

LCD5501Z LCD-style keypad

PC5100 2-Wire Addressable Interface Module

The PC5100 module is used to connect 2-wire addressable devices to the system. Up to 32 2-wire addressable devices can be added to the system.

NOTE: PC5100 v1.0 and lower modules can only support the first 32 zones on the PC1616/PC1832/PC1864 system.

NOTE: PC1616 expandable to 16 zones only.

PC5108 Eight Zone Expander Module

Eight zone expander module can be used to increase the number of zones on the system. Up to 7 modules can be connected to increase the system zones to a maximum of 64

(see the PC5108 Installation Instruction Sheet.)

NOTE: PC5108 v1.0 and lower modules can only support the first 32 zones on the PC1616/PC1832/PC1864 system. PC5108 v1.0 and lower modules enroll as two modules and use up two supervisory slots.

NOTE: Do not mix PC5108 v1.x and lower modules with PC5108 v2.0 and higher modules on the same system.

NOTE: PC1616 expandable to 16 zones only. The PC1832 expandable to 32 zones only.

PC5132 Wireless Receiver Module

The PC5132 Wireless Receiver module can be used to connect up to 32 fully supervised wireless devices (see the PC5132 Installation Manual for details).

NOTE: Only the first 32 zones on the PC1616/PC1832/PC1864 system can be used as wireless zones.

NOTE: PC1616 expandable to 16 zones only.

PC5200 Power Supply Output Module

The PC5200 can provide up to 1 Amp of additional power for modules or devices connected to the control panel. Up to 4 modules can be connected to the system. Each module requires a 16.5VAC 40VA transformer and 4 AH battery (see PC5200 Installation Instructions for details).

PC5204 Power Supply Output Module

The PC5204 can provide up to 1 Amp of additional power for modules or devices connected to the control panel. The module requires a 16.5VAC 40VA transformer and 4Ah(min.) battery. In addition, the module provides 4 programmable high current outputs (see PC5204 Installation Instructions for details).

PC5208 Eight Low Current Output Module

Adds 8 programmable low current outputs (50mA) to the control (see the PC5208 Installation Instructions for details).

NOTE: If you use the main panel and the PC5208 outputs, PGM 3 will work the same as the first PC5208 output, and PGM 4 will work the same as the second PC5208 output.

Escort5580(TC) Module

This Escort5580(TC) module will turn any touch-tone telephone into a fully functional keypad. The module also includes a built-in interface to control up to 32 powerline carrier type devices for lighting and temperature control (see the Escort5580(TC) Installation Manual for details).

NOTE: An Escort5580(TC) version 3.x or higher is needed to support more than 32 zones and/or 2 partitions.

PC5900 Audio Verification Module

The PC5900 series Audio Verification Modules provide «Talk/ Listen-In» capability for audio verification of alarms. The module permits the central station to monitor up to four microphones and to communicate to the occupants through 2 separate speakers.

PC5400 Printer Module

This PC5400 Printer Module allows the panel to print all events on the system to any serial printer. All events will be printed with the partition, time, date and the event that occurred (see PC5400 Installation Manual for details).

NOTE: The PC5400 v2.x and lower only supports events on partitions 1 and 2, and zones 1-32.

PC5401 Serial Interface Module

The PC5401 Serial Interface Module can be used to communicate with 3’rd party devices (automation) through a standard RS-232 serial connection (see the PC5401 Developer’s Guide for more information on communicating with the PC5401 module).

T-Link Local Area Network Communicator

The T-Link Local Area Network Communicator provides an efficient method of communicating via a Local Area Network (LAN). See the T-Link Installation Manual for more details.

TL250/TL300 Intranet/Internet Communicators

The T-Link Ethernet Communicator provides an efficient method of communicating via Internet/Intranet. See the T- Link TL250/TL300- Installation Manual for more details.

Alternate Communicators

Refer to the associated Skyroute™ Installation Manual, or GS3050 Installation Manual for programming details.

PC5700/PC5720 Fire Module

This is a zone expansion fire module that can be used for ULC Listed non-residential fire applications. The PC5720 can be used as an interface between the control panel and either a serial printer or a DVACs communication network.

NOTE: The PC5700/PC5720 enroll as two expander modules and use two supervisory slots each.

NOTE: Do not mix PC5700 v1.x and lower modules with PC5108 v2.0 and higher modules on the same system.

Enclosures/Cabinets

The PC1616/PC1832/PC1864 main board can be installed in the following metal enclosures/cabinets:

Enclosure

Description/Dimensions

PC500C

Description: Alternate Main Control Cabinet (House-

hold Burglary).

Approximate Dimensions: 213mm x 235mm x 76mm /

8.4” x 9.25” x 3.0”

PC5002C

Description: Cabinet to house the PC5204 Power Sup-

ply Output Module.

Approximate Dimensions: 213mm x 235mm x 76mm /

8.4” x 9.25” x 3.0”

PC5003C

Description: Main Control Cabinet for the PC1616/

(Removable

PC1832/PC1864 main panel with removable door. (UL/

Door)

ULC Household Fire & ULC Commercial Burglary) Made

with 22Ga steel.

Approximate Dimensions: 287mm x 297mm x 76mm /

11.3” x 11.7” x 3.0”

PC5003C

Description: Main Control Cabinet for the PC1616/

(Hinged Door)

PC1832/PC1864 main panel with removable door. Made

with 1.2mm thick steel.

Approximate Dimensions: 287mm x 297mm x 76mm /

11.3” x 11.7” x 3.0”

PC5004C

Description: Cabinet to house the Escort5580(TC)

Module and PC5400 Printer Module.

Approximate Dimensions: 229mm x 178mm x 66mm /

9.0” x 7.0” x 2.6”

PC5001C

Description: Cabinet to house the PC5108 Zone

Expander Module and the PC5208 Eight Low Current

Output Module.

Approximate Dimensions: 152mm x 122mm x 38mm /

6.0” x 4.8” x 1.5”

PC5001CP

Description: Plastic Cabinet to house the PC5108 Zone

Expander Module and the PC5208 Eight Low Current

Output Module.

Approximate Dimensions: 146mm x 107mm x 25mm /

5.75” x 4.2” x 1.0”

PUC-1

Description: Main control cabinet for the PowerSeries

panel. Made with 18Ga steel.

Approximate Dimensions: 318mm x 318mm x 102mm

/ 12.5” x 12.5” x 4.0”

CMC-1

Description: Alternate Main Control Cabinet (Commer-

cial Burglary)

Approximate Dimensions: 287mm x 297mm x 76mm /

11.3” x 11.7” x 3.0”

Multi-3

Description: Cabinet to house the PC5937.

Approximate Dimensions: 287mm x 297mm x 76mm /

11.3” x 11.7” x 3.0”

HS-CAB1000B

Description: Structured wiring cabinet for PC1616/

PC1832/PC1864 main panel, with a wire raceway in the

center of the cabinet.

Approximate Dimensions: 362mm x 362mm x 102mm

/ 14.25” x 14.25” x 4.0”

Approximate Dimensions of Cover: 389mm x 389mm

/ 15.3” x 15.3”.

HS-CAB3000LDR

Description: Structured wiring cabinet for PC1616/

PC1832/PC1864 main panel, with a wire raceway in the

center of the cabinet.

Approxmiate Dimensions: 724mm x 362mm x 102mm

/ 28.5” x 14.25” x 4.0”

Approximate Dimensions of Cover: 752mm x 389mm

/ 29.6” x 15.3”.

HS-CAB4000LDR

Description: Structured wiring cabinet for PC1616/

PC1832/PC1864 main panel, with a wire raceway in the

center of the cabinet.

Approximate Dimensions: 1086mm x 362mm x

102mm / 42.75” x 14.25” x 4.0”

PC4050C

Description: Alternate Main Control Cabinet (UL/ULC

Household Fire & ULC Commercial Burglary) for the

PC1616/PC1832/PC1864 main panel.

Approximate Dimensions: 305mm x 376mm x 124mm

/ 12.0” x 14.8” x 4.9”

PC4050CR

Description: Alternate Main Control Cabinet (UL Com-

mercial Fire) for the PC1616/PC1832/PC1864 main

panel.

Approximate Dimensions: 305mm x 376mm x 124mm

/ 12.0” x 14.8” x 4.9”

PC4050CAR

Description: Alternate Main Control Cabinet (ULC

Commercial Burglary) for the PC1616/PC1832/PC1864

main panel.

Approximate Dimensions: 305mm x 376mm x 124mm

/ 12.0” x 14.8” x 4.9”

Accessories can be installed in separate metal enclosures as follows:

Enclosure

Description/Dimensions

PC4003C

Description: Single expander cabinet made of 18Ga

steel, painted, hinged door, weight: 1050g.

Approximate Dimensions: 229mm x 178mm x 64mm /

9.0” x 7.0” x 2.5”

PC4051C

Description: Cabinet made of 18Ga steel, painted,

hinged door, weight: 3600g.

Approximate Dimensions: 427mm x 264mm x 106mm

/ 16.8” x 10.4” x 4.18”

All cabinets are provided with means for installing tamper protection switch (door opening detection and/or removal from the mounting position).

1.5 Battery Standby Times versus AUX Load

In accordance with EN50131-1 Standard, for a Power Supply Type A rated for Grade 2 systems, the battery standby time required in case of failure of the prime power source shall be a minimum of 12 hours.

The table below indicates the maximum load values applicable to the AUX+/-, Keybus (Red, Black) and PGM 1-4 outputs that the panel (PC1616/PC1832/PC1864) will be able to support when using a certain battery size for a certain period of time as applicable for each installation.

The AUX +/-, Keybus (Red, Blk) and PGM 1-4 outputs are all sharing the same load (max. 500mA), (max. 700mA for UL/ ULC), (max. 550mA for IMQ). Please refer to the other Power Series accessories current ratings when calculating the maximum load applicable for each installation.

Battery

Standby Times

Capacity

4hrs

12hrs

24hrs

36hrs

4Ah

500mA

220mA

7Ah

500mA

480mA

150mA

14Ah

500mA

480mA

280mA

24Ah

500mA

500mA

Standard Battery Charging Current: 400mA (280mA for IMQ).To be used with 4Ah or 7Ah batteries.

High Battery Charging Current: 700mA. To be used with 14Ah or 24Ah batteries.

NOTE: Program Section [701] option 7 to ON to enable high battery charging current, if 14Ah or 24Ah battery is used.

Refer to the following table for UL/ULC Applications:

Battery

Standby Times (UL/ULC)

Capacity

4hrs

24hrs

4Ah

700mA

7Ah

700mA

180mA

14Ah (2x7Ah in parallel)

700mA

470mA

NOTE: When two batteries are required in order to meet the minimum standby times, the DSC Enclosure Model Power UC1 shall be used.

NOTE: A sealed, rechargeable, lead acid battery or gel type battery is required to meet UL requirements for power standby times.

NOTE: UL Residential/Commercial Burglary installations require 4Hrs Power Standby time.

NOTE: UL/ULC Residential Fire & Home Care installations require 24 Hr power standby. ULC Commercial Burglary and Fire monitoring installations require 24 Hr power standby.

NOTE: Replace batteries every 3-5 years.

NOTE: Battery capacity will deteriorate with age and number of charge/discharge cycles.

Section 2: Installation and Wiring

The following section provides a description of how to wire and configure devices and zones.

2.1 Installation Steps

The following steps are provided to assist with the installation of the panel. It is suggested that you read over this section briefly to get an overall understanding of the order of installation. Once this is done carefully work through each step. Working from this plan will help reduce problems and reduce the overall installation time required.

Step 1 Create a Layout

Draw a rough sketch of the building and include all alarm detection devices, zone expanders, keypads and all other modules that are required.

Step 2 Mounting the Panel

Locate the panel in a dry area, preferably located near an unswitched AC power source and the incoming telephone line. Before attaching the cabinet to the wall be sure to press the five circuit board mounting studs into the cabinet from the back.

NOTE: Complete all wiring before applying AC or connecting the battery.

Step 3 Wiring the Keybus

Wire the Keybus to each of the modules following the guidelines provided in Section 2.4.

Step 4 Assigning Zones to Zone Expanders

If zone expander modules are being used the modules must be configured so the panel knows which zones are assigned to each expander. Follow the guideline provided in Section 2.6 to assign zones to expanders.

Step 5 Zone Wiring

Power down the control panel and complete all zone wiring. Follow the guidelines provided in section 2.10 to connect zones using normally closed loops, single EOL resistor, double EOL resistors, Fire zones and Keyswitch Arming zones.

Step 6 Completing Wiring

Complete all other wiring including bells or sirens, telephone line connections, ground connections or any other wiring necessary. Follow the guidelines provided in section 2.2 “Terminal Descriptions”.

Step 7 Power up the Control Panel

Once all zone and Keybus wiring is complete, power up the control panel.

NOTE: The panel will not power up if only the battery is connected.

Step 8 Keypad Assignment

Keypads must be assigned to different slots to be properly supervised. Follow the guideline provided in section 2.7 to assign keypads.

Step 9 Confirming Module Supervision

By default, all modules are supervised upon installation. Supervision is enabled at all times so that the panel can indicate a trouble if a module is removed from the system.

To confirm that each module is properly supervised, follow the guidelines provided in section 2.8.

Step 10 Programming the System

Section 4.0 provides a complete description of how to program the panel. Section 5.0 contains complete descriptions of the various programmable features, what options are available and how the options function. The Programming

Worksheets should be filled out completely before attempting to program the system.

Step 11 Testing the System

Test the panel completely to ensure that all features and functions are operating as programmed.

2.2Terminal Descriptions

AC Power Terminals

The panel requires a 16.5V, 40VA transformer. Connect the transformer to these terminals.

The panel can be programmed to accept a power line frequency of either 50Hz AC or 60Hz AC in programming section [701], option [1].

NOTE: Do not connect the transformer until all other wiring is complete.

Battery Connection

The battery is used to provide back up power in the event of an AC power failure and to provide additional current when the panel demands exceed the power output of the transformer, such as when the panel is in alarm.

NOTE: Do not connect the battery until all other wiring is complete.

Connect the RED battery lead to the positive of the battery, the BLACK battery lead to the negative.

The High Current Charge/Standard Battery Charge option (section [701], option [7]) allows you to choose between a high current battery charge and the standard battery charge rate.

High Current/Standard Battery Charge . . . . . . . . .Section [701]: [7]

Auxiliary Power Terminals — AUX+ and GND

These terminals provide up to 500mA of current at 12 VDC (700mA of current at 12VDC for UL/ULC) (550mA of current at 12VDC for IMQ) for devices requiring power (rated 11.6- 12.6 VDC for UL residential applications). Connect the positive side of any device requiring power to the AUX+ terminal, the negative side to GND. The AUX output is protected; if too much current is drawn from these terminals (wiring short) the panel will temporarily shut off the output, until the problem is corrected.

NOTE: When using a 12V 14Ah battery, the maximum AUX capacity for 24-hour standby is 470mA.

Bell Output Terminals — BELL+ and BELL-

These terminals provide up to 2A of current at 12VDC (with standby battery; 700 mA continuous) for powering bells, sirens, strobes or other warning type equipment. Connect the positive side of any alarm warning device to BELL+, the negative side to BELL–. The BELL output is protected; if too much current is drawn from these terminals (wiring short) the BELL PTC will open.

The Bell output is supervised. If no alarm warning device is being used connect a 1KΩ resistor across BELL+ and BELL– to prevent the panel from displaying a Bell Trouble condition.

NOTE: The Bell output is current limited with a 2A PTC.

NOTE: Steady, Pulsed and Temporal Three Pattern alarms are supported.

Keybus Terminals — RED, BLK, YEL, GRN

The Keybus is used by the panel to communicate with modules and by modules to communicate with the panel. Each module has four Keybus terminals that must be connected to the four Keybus terminals on the panel.

Programmable Outputs — PGM1 to PGM4

Each PGM output is designed so that when activated by the panel, the terminal will switch to ground

PGM1, PGM3, and PGM4 can each sink up to 50 mA of current. These PGMs can be used to activate LEDs or a small buzzer. Connect the positive side of the LED or buzzer to AUX+, the negative side to the PGM.

PGM2 is a high current output (300mA) and operates similarly to PGM1. If more than 300 mA of current is required, a relay must be used. Refer to the diagram. PGM2 can also be configured as an input.

A minimum ¼” (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections.

North America Only

POWER LIMITED

PC Board

Stand Off

Cable Tie (not supplied) recommended

Cabinet

Primary:120VAC/60Hz.

UA503

DSC

PC1616/1832/1864

DSCPTD 1640U

Secondary: 16.5VDC 40VA

Class II Transformer

WARNING:

NOTE: Do not connect

High Voltage. Disconnect AC Power

transformer to receptacle

and telephone lines before servicing

controlled by a switch

PC1864

PC1864

Only

PC1832

CON1

Only

TB-2

BAT+BAT-

AUX+ BELL+

PGM1 PGM3

Z7 COM Z8 EGND

RING

R-1

AC AC

AUXBELLRED BLK YEL GRN

PGM2 PGM4 Z1 COM Z2 Z3 COM Z4 Z5 COM Z6

TIP

T-1

12V / 7 AHr

12V / 7 AHr

BLACK

RED

NON-POWER LIMITED

DSC Model BD7-12

or equivalent

Battery

StandbyTime:

24Hrs min.

NOTE: Wire entry for power limited wiring must be separated by a different entry access from non-power limited wiring.

Zone Input Terminals — Z1 to Z8

Each detection device must be connected to a zone terminal on the system. It is suggested that each zone have one detection device however it is possible to wire multiple detection devices to the same zone.

For zone wiring details, see section 2.10 ’Zone Wiring’ .

Telephone Connection Terminals — TIP,RING,T-1,R-1

If a telephone line is required for central station communication or downloading, connect an RJ-31X jack in the following manner:

Connect the PC1616/PC1832/PC1864 and modules that use the telephone line(s) in the following order:

PC1616

PC5900

PC18xx

NOTE: Ensure that all plugs and jacks meet the dimension, tolerance and metallic plating requirements of 47 C.F.R. Part 68, SubPart F. For proper operation there must be no other telephone equipment connected between the control panel and the telephone company facilities.

NOTE: Do not connect the alarm panel communicator to telephone lines intended for use with a FAX machine. These lines may incorporate a voice filter which disconnects the line if anything other than FAX signals are detected, resulting in incomplete transmissions.

2.4 Keybus Operation and Wiring

The Keybus is used by the panel to communicate with all modules connected and by the modules to talk to the panel. The RED and BLK terminals are used to provide power while YEL and GRN are clock and data.

The 4 Keybus terminals of the panel must be connected to the 4 Keybus terminals or wires of all modules.

The following conditions apply:

Keybus should be run with minimum 22 gauge quad (0.5mm), two pair twisted preferred

The modules can be home run to the panel, connected in series or can be T-tapped

Any module can be connected anywhere along the Keybus, you do not need a separate Keybus wire run for keypads, zone expanders etc.

No module can be more than 1,000’/305m (in wire length) from the panel

NOTE: Shielded wire should not be used for Keybus wiring.

Example of Keybus Wiring

Module (A) is wired correctly as it is within 1,000’/305m of

the panel, in wire distance.

Module (B) is wired correctly as it is within 1,000’/305m of the panel, in wire distance.

Module (C) is NOT wired correctly as it is further than

1,000’/305m from the panel, in wire distance.

2.5 Current Ratings — Modules & Accessories

In order for the PC1616/PC1832/PC1864 system to operate properly, the power output capabilities of the main control and expansion devices must not be exceeded. Use the data presented below to ensure that no part of the system is overloaded and cannot function properly.

2.3 Wire Routing for Power & Non-Power Limited

All wiring entry points are designated by the arrows. All circuits are classified UL installation power limited except for the battery leads which are not power limited.

WWW.DIYALARMFORUM.COM

6

PC1616/PC1832/PC1864 Device Ratings

Max

Device

Description

Rating

@12VDC

PK5500

LCD Keypad

125mA

PK5501

ICON Keypad

125mA

PK5508

8 Zone LED Keypad

125mA

PK5516

16 Zone LED Keypad

125mA

RFK5500

LCD Keypad with Wireless Module

135mA

RFK5501

ICON Keypad with Wireless Module

135mA

RFK5508

8 Zone LED Keypad With Wireless

135mA

Module

RFK5516

16 Zone LED Keypad With Wireless

135mA

Module

LCD5500Z

LCD Keypad

85mA

LCD5501Z

ICON Keypad

45mA

LCD5501Z32-433

ICON Keypad with Wireless Module

260mA

LCD5511

ICON Keypad

100mA

LED5511Z

8 Zone LED Keypad

100mA

PC5532Z

32 Zone LED Keypad

85mA

PC5516Z

16 Zone LED Keypad

85mA

PC5508Z

8 Zone LED Keypad

85mA

PC5108

Zone Module

35mA

PC5132

Wireless Module

125mA

PC5200

Output Module

20mA

PC5204

Output Module

20mA

PC5208

Output Module

50mA

PC5320

Multiple Receiver Interface Module

55mA

Escort5580(TC)

Voice Prompting Module

150mA

PC5400

Printer Module

65mA

PC5401

Data Interface Module

35mA

PC5700

Fire Module

150mA

PC5900

Audio Verification Module

50mA

PC5904

Central Station Talk/Listen Module

175mA

PC5921

Intercom Audio Station

20mA

PC5921 EXT

Door Box Audio Station

20mA

PC5921 EXT/R

Door Box Audio Station

35mA

System Output Ratings

Device

Output

Rating (12VDC)

PC1616

AUX:

500mA (700 mA for UL/ULC).

PC1832

Subtract the listed rating for each keypad,

PC1864

expansion module and accessory connected to

AUX or Keybus.

BELL:

700 mA. Continuous Rating.

2.0 A. Short Term. Available only with stand-by

battery connected.

PC5200

AUX:

1.0 A.Continuous Rating. Subtract for each

device connected.

3.0 A. Short Term. Available only with stand-by

battery connected.

PC5204

AUX:

1.0 A. Continuous Rating. Subtract for each

device connected.

3.0 A. Short Term. Available only with stand-by

battery connected.

PC5208

AUX:

250 mA. Subtract for each device connected.

Subtract the total load on this terminal from the

PC1616/PC1832/PC1864 AUX/Keybus output.

PC5108

VAUX:

100 mA. Subtract for each device connected.

Subtract the total load on this terminal from the

PC1616/PC1832/PC1864 AUX/Keybus output.

Other Devices

Read the manufacturer’s literature carefully to determine the maximum current requirement (during activation or alarm) and use this value for loading calculations. Do not allow connected devices to exceed the system capabilities during any possible operational mode.

2.6 Assigning Zones to Zone Expanders

The main panel contains zones 1 to 8. Additional zone expanders may be added to increase the number of zones on the system. Each zone expander consists of one group of 8 zones. Each module must be set to assign the specific zones to the expander. To do this, set the jumpers located on the expander to the proper settings (see chart below).

NOTE: PC5108 v1.0 and lower modules can only support the first 32 zones on the PC1616/PC1832/PC1864 system. PC5108 v1.0 and lower, PC5700 enrolls as two expander modules.

NOTE: Do not use PC5108 v1.0 and v2.0 simultaneously on the same PC1616/PC1832/PC1864 panel.

NOTE: Before a zone expander will work properly, you must set the jumpers so the panel can determine the correct zone assignment.

The following are jumper settings for different zone assignments for PC5108 v2.0 modules. If you need to enroll PC5108 v1.0 or PC5700 modules, refer to the appropriate module Installation Sheet for the correct jumper settings.

Module Jumpers

System Zones Assigned

J1

J2

J3

ON

ON

ON

Zones disabled

OFF

ON

ON

Zones 09 — 16

ON

OFF

ON

Zones 17 — 24

OFF

OFF

ON

Zones 25 — 32

ON

ON

OFF

Zones 33 — 40

OFF

ON

OFF

Zones 41 — 48

ON

OFF

OFF

Zones 49 — 56

OFF

OFF

OFF

Zones 57 — 64

The following is a diagram of the PC5108 zone expander module and where the jumper switches are located. Refer to the PC5108 Installation Instruction sheet for the module for more information.

NOTE: Only jumpers J1, J2, and J3 determine the zone assignment for the module.

2.7 Keypad Assignment

There are 8 available slots for keypads. LED and ICON keypads by default are assigned to slot 1. LCD keypads are assigned by default to slot 8. Keypads can each be assigned to a different slot (1 to 8) which offers two advantages. The panel can supervise the keypad connection to indicate a trouble condition if it is removed. Also keypads can be assigned to operate on a specific partition, or to operate as a global keypad.

How to Assign Keypads

1.Enter Installer Programming

2.Press [000] for Keypad Programming

3.Press [0] for Partition and Slot Assignment

4.Enter a two digit number to specify the partition and slot assignment.

1st digit — enter 0 for Global operation, or enter 1-8 for Partitions 1-8

2nd digit — enter 1 to 8 for Slot Assignment

5.Press the [#] key twice to exit programming.

6.Continue this procedure at each keypad until all have been assigned to the correct slot and partition (see section [902].

NOTE: All keypad assignments must be done at each keypad on the system. When using LCD keypads, one keypad must remain in slot 8 to upload/download LCD information. Do not assign more than one keypad to the same slot.

NOTE: The following keypad versions can only be used on the Partition 1 & Partition 2, and the first 8, 16, or 32 zones: PC5508(Z), PC5516(Z), PC5532(Z) versions v2.0 & lower, LCD5500(Z) versions 3.x and lower. To assign a keypad to a slot and select the partition it will operate in, enter the following:

Function Key Programming

Each of the 5 function keys on each keypad may be programmed for different operations.

1.Enter Installer Programming.

2.Press [000] for Keypad Programming.

3.Enter [1] to [5] to select function key to program.

4.Enter a 2-digit number for function key option — [00] — [32].

5.Continue from step 3 until all function keys are programmed.

6.Press [#] key twice to exit Installer Programming.

Keypad Function Keys

[00] — Null

[10] — Alarm Memory

[24] — Bypass Group Recall

[01] — Partition 1 Select

[11] — User Programming

[26] — Time & Date Program

[02] — Partition 2 Select

[12] — User Functions

[27] — Partition 3 Select

[03] — Stay Arm

[13] — Command Output 1

[28] — Partition 4 Select

[04] — Away Arm

[14] — Command Output 2

[29] — Partition 5 Select

[05] — No Entry Arm

[16] — Quick Exit

[30] — Partition 6 Select

[06] — Chime On/Off

[17] — Activate Stay/Away

[31] — Partition 7 Select

[07] — System Test

[19] — Command Output 3

[32] — Partition 8 Select

[08] — Bypass Mode

[21] — Command Output 4

[09] — Trouble Display

[23] — Bypass Recall

For details on the operation of Function Keys, see section

4.3’Function Keys’ .

2.8Confirming Module Supervision

By default, all modules are supervised upon installation. Supervision is enabled at all times so that the panel can indicate a trouble if a module is removed from the system.

To check which modules are currently connected and supervised:

1.Press [*][8][Installer Code] to enter Installer Programming.

2.Press [903] to display Module Supervision Field.

3.On an LCD keypad, use the arrow keys to scroll through the modules the panel has found on the system.

On LED/ICON keypads, zone lights will be turned on according to what modules the panel has found on the system. Refer to the following chart:

Light

Module/Device

Light

Module/Device

[1]

Keypad 1

[16]

Zones 57 to 64

[2]

Keypad 2

[17]

Wireless Receiver

[3]

Keypad 3

[18]

PC5208

[4]

Keypad 4

[19]

PC5204

[5]

Keypad 5

[20]

PC5400

[6]

Keypad 6

[21]

PC5900

[7]

Keypad 7

[22]

Alternate Communicator

[8]

Keypad 8

[23]

Future Use

[9]

Zones 9 to 16

[24]

Escort5580(TC)

[10]

Zones 17 to 24

[25]

Future Use

[11]

Zones 25 to 32

[26]

PC520X-1

[12]

Zones 33 to 40

[27]

PC520X-2

[13]

Zones 41 to 48

[28]

PC520X-3

[14]

Zones 49 to 56

[29]

PC520X-4

[15]

PC5100

If a module is connected but does not show as being present, it may be due to any of the following reasons:

it is not connected to the Keybus

there is a Keybus wiring problem

the module is more than 1,000’/305m from the panel

the module does not have enough power

the wireless receiver does not have any devices added

NOTE: Module supervision will not display correctly at an LCD5500Z v2.x and lower keypad.

2.9 Removing Modules

If a module is no longer required on the system, the panel must be told to stop supervising the module. To do this:

1.Power down the panel by removing the backup battery and AC.

2.Remove the module from the Keybus.

3.Power up the panel by connecting the backup battery and AC.

4.Press [*][8][Installer Code] to enter Installer Programming.

5.Press [902] to enable supervision. The panel will automatically search for all modules connected to the system for the next 60 seconds. Do not perform any other operations during this 60 second period.

6.Once the search is complete enter section [903] to confirm that the correct modules are supervised on the system.

2.10Zone Wiring

For a complete description of the operation of all zone types, see section 5.2 ’Basic Programming’ section [001]-[004]. The panel can be programmed to supervise normally closed, End of Line, or Double End of Line loops. Refer to the following sections to study each type of individually supervised zone wiring.

NOTE: Any zone programmed for Fire or 24 Hour Supervisory must be wired with a single End of Line (EOL) resistor regardless of the type of zone wiring supervision selected for the panel (section [013], options [1] and [2]). See Zone Definitions [001]-[004]. If you change the zone supervision options from DEOL to EOL or from NC to DEOL (section [013], options [1] or [2]), power the system down completely, and then power it back up for correct operation.

NOTE: For UL Listed Installations use SEOL or DEOL only. NOTE: Use minimum 22 AWG wire, maximum 18 AWG wire. NOTE: Do not use shielded wire.

NOTE: Wire run resistance shall not exceed 100Ω.

Burglary Zone Wiring Chart

Wire Gauge

Maximum Wire length to End of Line Resistor

24

1900 feet / 579 meters

22

3000 feet / 914 meters

20

4900 feet / 1493 meters

19

6200 feet / 1889 meters

18

7800 feet / 2377 meters

Normally Closed (NC) Loops

To enable normally closed loops, program section [013], option [1] to ON.

NOTE: Do not use Normally Closed Loops for UL Listed systems.

ANY Z ANY COM

ANY Z ANY COM

TERMINAL TERMINAL

TERMINAL TERMINAL

DSC PC1616, PC1832, PC1864 User Manual

The following chart shows zone status under certain conditions for NC Loops:

Loop Resistance

Loop Status

0Ω(shorted wire, loop shorted)

Secure

Infinite (broken wire, loop open)

Violated

Normally Closed Loops . . . . . . . . . . . . . . Section [013], Option [1]

Single End Of Line (EOL) Resistors

To enable panel detection of single end-of-line resistors, program section [013], options [1] and [2] to OFF.

NOTE: This option should be selected if either Normally Closed (NC) or Normally Open (NO) detection devices or contacts are being used.

The following chart shows zone status under certain conditions for SEOL:

Loop Resistance

Loop Status

0Ω(shorted wire, loop shorted)

Violated

5600Ω(contact closed)

Secure

Infinite (broken wire, loop open)

Violated

End of Line Resistors . . . . . . . . . . . . . . . . Section [013], Option [1] Single End of Line Resistors . . . . . . . . . . . Section [013], Option [2]

Double End of Line (DEOL) Resistors

Double End of Line resistors allow the panel to determine if the zone is in alarm, tampered or faulted.

To enable panel detection of double end of line resistors, program section [013], option [1] to OFF and option [2] to ON.

NOTE: If the Double EOL supervision option is enabled, all hardwired zones must be wired for Double EOL resistors, except for Fire and 24 Hour Supervisory zones. Do not use DEOL resistors for Fire zones or 24 Hour Supervisory zones.

NOTE: Do not wire Fire zones to keypad zone terminals if the DEOL supervision option is selected.

NOTE: This option can only be selected if Normally Closed (NC) detection devices or contacts are being used. Only one NC contact can be connected to each zone.

The following chart shows zone status under certain conditions for DEOL:

Loop Resistance

Loop Status

0Ω(shorted wire, loop shorted)

Fault

5600Ω(contact closed)

Secure

Infinite (broken wire, loop open)

Tamper

11200Ω(contact open)

Violated

End-of-Line Resistors . . . . . . . . . . . . . . . . Section [013], Option [1] Double End-of-Line Resistors . . . . . . . . . . Section [013], Option [2]

Fire Zone Wiring — 4-wire Smoke Detectors

All zones defined as Fire (see section 5.2 ’Basic Programming’ ) must be wired according to the following diagram:

For a complete description of how fire zones operate, see section 5.2 ’Basic Programming’ sections [001]-[004] option 07 and 08.

NOTE: Smoke detectors must be latching type. To reset smoke detector, enter [*][7][2].

Compatible 4-Wire Smoke Detectors

Model

Model

Model

FAS-410x

FSA-410xLST

FSA-410xRST

FSA-410xT

FSA-410xR

FSA-410xLRST

FSA-410xS

FSA-410xRT

FSA-410xST

FSA-410xRS

For model numbers above: x=A (ULC)

x=B (UL) x=C (CE)

Fire Zone Wiring — 2-wire Smoke Detectors

If PGM 2 has been programmed for 2-Wire Smoke Detector connection (see section 5.2 ’Basic Programming’ ) , the detectors must be wired according to the following diagram:

For a complete description of how fire zones operate, see section 5.2 ’Basic Programming’ section [009] option 04.

NOTE: Do not combine models from different manufacturers on the same circuit. Operation may be impaired.

NOTE: Refer to smoke detector installation sheet when positioning detectors.

Compatible 2-Wire Smoke Detectors

Model

Model

Model

FAS-210B

FSA-210BLST

FSA-210BRST

FSA-210BT

FSA-210BR

FSA-210BLRST

FSA-210BS

FSA-210BRT

FSA-210BST

FSA-210BRS

For model numbers above: x=A (ULC)

x=B (UL) x=C (CE)

2-Wire Smoke Detector Initating Circuit

Item

Specification

Style/Class, Supervised, Power Limited

Style B (Class B)

Compatibility Identifier

PC18-1

DC Output Voltage

9.8-13.8 VDC

Detector Load

2mA (MAX)

Single End of Line Resistor (SEOL)

2200Ω

Loop Resistance

24Ω(MAX)

Standby Impedance

1020Ω(NOM)

Alarm Impedance

570Ω(MAX)

Alarm Current

89mA (MAX)

Keyswitch Zone Wiring

Zones may be programmed to be used as keyswitch arming zones and must be wired according to the following diagram:

For a complete description of how keyswitch zones operate, see section 5.2 ’Basic Programming’ sections [001]-[004] option 22 and 23.

2.11 Keypad Zone/PGM

Keypads with zone inputs can be connected to devices such as door contacts. This saves you from running wires back to the control panel for every device.

To install the keypad, open the keypad plastic. Refer to the Installation Sheet that came with the keypad for instructions on how to open the keypad. Locate the terminals on the keypad circuit board. Connect the four Keybus wires from the control panel: the red wire to R, the black to B, the yellow to Y and the green to G.

LCD55XXZ

To connect the zone input on an LCD55XXZ keypad, run one wire to the Z terminal and the other to B. For powered devices, use red and black to supply power to the device. Run the red wire to the R (positive) terminal and the black wire to the B (negative) terminal.

When using end of line supervision, connect the zone according to one of the configurations outlined in section 2.10 ‘Zone Wiring‘ on page 8.

NOTE: LCD55XXZ zones do not support DEOL resistors.

LCD55XXZ

PK55XX/RFK55XX

PK55XX/RFK55XX keypad comes with a Z/P terminal. This terminal can be configured as an input (zone) or output (PGM).

To connect the zone input on a PK55XX/RFK55XX keypad, run one wire to the Z/P terminal and the other to B. For powered devices, use red and black to supply power to the device. Run the red wire to the R (positive) terminal and the black wire to the B (negative) terminal. The PK55XX/ RFK55XX keypad zone supports Normaly Closed Loops, Single End of Line and Double End of Line.

To connect the PGM output on a PK55XX/RFK55XX keypad, run one wire to the Z/P terminal and the other to R.

PK55XX/RFK55XX

PK55xx

RED

R

BLK

B

YEL

Y

GRN

G

To zone or

Z/P

PGM output

NOTE: End of line resistors must be placed on the device end of the loop, not at the keypad.

Assigning Keypad Zones

When using keypad zone inputs, each input used must be assigned a zone number in Installer’s Programming.

First, ensure that you have enrolled all installed keypads into the desired slots (see section 2.7 ’Keypad Assignment’ ) to assign the keypad to a slot.

Next, enter programming section [020] to assign the zones. There are eight programming locations in this section, one for each keypad slot. Enter a 2-digit zone number for each of the keypad zones. This number must be entered in the location corresponding to the keypad to which each zone is connected.

NOTE: If a keypad zone input is assigned to zone number 1 to 8, the corresponding zone cannot be used on the main control panel.

Once the keypad zones are assigned, you must also program zone definitions and zone attributes (see Section 5.2 Basic Programming PWS Sect 3 [001]-[004] and Section 5.3 Advanced System Programming PWS Sect 4 [101]-[164]).

2.12 Zone Activity Log

This feature stores the date stamp of each zone activation event. It stores the last day, month and year a zone was violated. This data can be retrieved during the installer’s DLS access.

NOTE: If the panel is powered down, this data will be lost.

Section 3: How to Program

The following section of the manual describes how to enter Installer Programming and how to program the various sections.

NOTE: It is extremely important that you read the following section of the manual to completely understand how to program the panel.

3.1 How to Enter Installer Programming

NOTE: It is important to watch the Ready light. If the

Installer Programming is used to program all communicator

light is flashing any number you enter will be pro-

and panel options. The Installer Code is [5555] at default,

grammed as the HEX equivalent.

but should be changed to prevent unauthorized access to

Example: To enter ‘C1’ for a closing by user 1, you would

programming.

enter [*] [3] [*], [1]

NOTE: Once the Installer’s Mode is exited, the system will

[*] to enter Hexadecimal mode (Ready light flashes)

reset. This will take 15 seconds. Do not attempt to per-

[3] to enter C

form any system function during this reset period. In addi-

[*] to return to decimal mode (Ready light is solid)

tion, all outputs will return to their normal, deactivated

[1] to enter digit 1

state (or activated if inverted).

If you enter information into a section and make a mistake,

press the [#] key to exit the section. Select that section again

NOTE:

EN

EN installations will restrict access to the Mas-

and re-enter the information correctly.

If you are using a pulse communications format, a decimal

ter code section [007] in installers programming. The

zero [0] does not transmit. Programming a zero [0] tells the

Installer may view the Master Code via DLS.

panel not to send any pulses for that digit. Decimal zero [0] is

LED Keypad

a filler digit. To make a zero [0] transmit, it must be pro-

Step 1: From any keypad enter [*][8][Installer Code].

grammed as a Hexadecimal ‘A’.

• The ‘Program’ light will flash to indicate you are in pro-

Example: for the three digit account number ‘403’, you would

gramming

enter [4], [*] [1] [*] [3], [0].

• The ‘Armed’ light will turn on to indicate the panel is

[4] to enter the digit 4

waiting for the 3 digit Section number to program

[*] to enter Hexadecimal mode (Ready light flashes)

Step 2: Enter the 3 digit Section number you want to pro-

[1] to enter A

gram.

[*] to return to decimal mode (Ready light is solid)

• The Armed light will turn off

[3] to enter the digit 3

• The Ready light will turn on to indicate the panel is ready

[0] to enter the digit 0 as a filler digit.

for the information for the selected Section

3.4 Programming Toggle Options

NOTE: If the 3 digit section number entered is not valid or

Some Sections contain several toggle options. The panel will

the module that pertains to the Section is not present, the

use zone lights 1 through 8 to indicate if the different options

keypad will sound a 2 second error tone.

are enabled or disabled. Refer to the Programming Work-

LCD Keypad

sheets to determine what each option represents and

Step 1: From any keypad enter [*][8][Installer Code].

whether the light should be ON or OFF for your application.

The Keypad will display ‘Enter Section’ followed by three

Press the number corresponding to the option to toggle the

dashes.

light ON or OFF.

Step 2: Enter the 3 digit Section number you want to pro-

Once all the toggle options have been selected correctly

gram. The keypad will now display information for the section

press the [#] key to exit the Section and save the changes.

entered.

The panel will turn off the Ready light and turn on the Armed

Installer Code

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [006]

light.

3.5 Viewing Programming

3.2 Programming Decimal Data

LED and ICON Keypads

When the Ready light is ON the panel is waiting for the infor-

Any programming section can be viewed from an LED or

mation to be programmed for the selected Section. Enter the

ICON keypad. When a programming section is entered, the

information written in the boxes for the Section found in the

keypad will immediately display the first digit of information

Programming Worksheets.

programmed in that section.

If a digit is entered for each program box in a Section the

The keypad displays the information using a binary format,

panel will automatically exit from the Section. It will turn OFF

according to the following chart:

the Ready light and turn the Armed light back ON.

See Hex data entry instructions

You can also press the [#] key to exit a Section before enter-

ing data for every box. This is handy if you only need to

change the first few program boxes. All other locations in the

Section will remain unchanged. If the [#] key is pressed the

panel will turn OFF the Ready light, turn ON the Armed light

and exit you from the Section.

3.3 Programming Hexadecimal Data

Press any of the Emergency Keys (Fire, Auxiliary or Panic)

On occasion, hexadecimal (HEX) digits may be required. To

to advance to the next digit.

program a HEX digit press the [*] key. The panel will enter

When all the digits in a section have been viewed, the panel

HEX programming and Ready light will begin to flash.

will exit the section: the Ready Light will turn OFF, and the

The following table indicates which number should be

Armed light will turn ON, waiting for the next three-digit pro-

pressed to enter the corresponding HEX digit:

gramming section number to be entered.

1 = A 2 = B 3 = C 4 = D 5 = E 6 = F

Press the [#] key to exit the section.

After the correct HEX digit is entered the Ready light will

LCD Keypad

continue to flash. If another HEX digit is required press the

corresponding number. If a decimal digit is required press

When a programming section is entered, the keypad will

the [*] key again. The Ready light will turn on solid and the

immediately display all the information programmed in that

panel will return to regular decimal programming.

section. Use the arrow keys (< >) to scroll through the data

being displayed. To exit the section, scroll past the end of the data displayed, or press the [#] key.

WWW.DIYALARMFORUM.COM

11

Section 4: Keypad Commands

Use any system keypad to enter commands, or to program the PC1616/PC1832/PC1864 security system. The LED keypad uses function and zone indicator lights to represent alarm functions and status. The LCD keypad provides a written description on the liquid crystal display and uses function indicator lights to communicate alarm status to the user. The PC1616/PC1832/PC1864 User’s Guide provides basic directions for arming and disarming the system, bypassing zones and performing user functions from the keypads. The following sections provide additional details on these functions.

4.1Arming and Disarming

Arming

The system cannot be armed unless the ‘Ready’ light is on. If the ‘Ready’ light is not on, ensure all protected doors and windows are secure and stop movement in areas covered by motion detectors.

When the ‘Ready’ light is on, enter a valid access code. As each digit is pressed the keypad will beep. If an incorrect code is entered, the keypad will emit a steady 2 second beep to indicate that the code was not correct. If the code is correct but the ‘Ready’ light was not on, the panel will beep six times rapidly followed by a long two second beep to indicate the system was not ready.

When the correct code is entered and the system is ready, the panel beeps six times rapidly, and the ‘Armed’ light turns on. The panel begins counting down the exit delay. If the Audible Exit Delay option is enabled, the keypad will beep every second until the exit delay expires. The keypad will beep rapidly for the last 10 seconds of exit delay to warn the user the system is about to arm. Exit the premises through the designated entry/exit door before the exit delay expires.

Users can restart the exit delay while it is counting down by pressing the Away key. The system will not log the user who re-started the exit delay, unless the Quick Arming Disabled/Function Keys Require Code option is turned on (section [015], option [4]).

NOTE: If the system has been Stay armed, or armed with no entry delay ([*][9]), pressing the Away key will not restart an exit delay.

NOTE: If the system is armed while an alarm is in memory, the mode cannot be changed.

Other methods of arming are available (See section “[*][0] Quick Arm”, “[*][9] Arming without Entry Delay”, and section 4.4 “Function Keys”).

NOTE: The PC1616/PC1832/PC1864 has a built-in feature called Audible Exit Fault (see Section [013], option 6 for more information).

NOTE: For SKAFOR Installations, the keypad will sound a steady tone for 5 seconds when the system is armed while a trouble is present. Exit delay should continue normally (silent or audible) after 5 seconds.

Stay and Away Arming

When a user arms the system with an access code, if any zones on the system have been programmed as Stay/Away, the panel will immediately turn on the ‘Bypass’ light. The panel will then monitor all zones programmed as Delay 1 and Delay 2. If no delay type zone is violated by the end of the exit delay (e.g. nobody leaves through the entry/exit door), the panel will bypass all Stay/Away type zones. The panel is now “Stay” armed. The ‘Bypass’ light will remain on to inform the home owner that the interior protection is bypassed. This is a convenience for users that want to arm the panel while at home. Using this method, users do not have to bypass the interior zones manually.

Users can add Stay/Away zones back into the system at any time by entering [*][1] (see section ’[*][1] Zone Bypassing’ ), or by using the Away button.

If a delay zone is violated during the exit delay (e.g. somebody leaves through the designated entry/exit door), all zones will be active after the exit delay expires. The panel is now “Away” armed. The Bypass light on the keypad will be off. Other methods of Stay and Away arming are available (see section 4.3 ’Function Keys’ ).

NOTE: The buzzer will not sound during “Stay Arming”.

Stay Arming

When a user arms the system by pressing the Stay button, if any zones on the system have been programmed as Stay/ Away, the panel will immediately turn on the ‘Bypass’ light. After the exit delay the panel will bypass all Stay/Away type zones. The panel is now “Stay” armed. The ‘Bypass’ light will remain on to inform the home owner that the interior protection is bypassed. This is a convenience for users that want to arm the panel while at home. Using this method, users do not have to bypass the interior zones manually.

Users can add Stay/Away zones back into the system at any time by entering [*][1] (see section ’[*][1] Zone Bypassing’ ), or by using the Away button.

Away Arming

When a user arms the system by pressing the Away button, the panel will begin the exit delay. All zones will be active after the exit delay expires. The panel is now “Away” armed. The Bypass light on the keypad will be off.

Using the Away Button While Stay Armed

If a partition is armed in Stay mode and a user wishes to leave the premises without having to disarm and re-arm the system, they may press the Away button. The system will begin counting the standard exit delay, allowing the user to leave without actually disarming. The panel will log “Armed in Away Mode” upon completion of the Exit Delay. This feature is useful for users with Wireless Keys with Stay/Away buttons, and who wish to have their panel armed at all times.

Using the Stay Button While Away Armed

Pressing the Stay key while a partition is Away armed will begin the Exit Delay again. The panel will log “Armed in Stay Mode”. This feature is useful for users with Wireless Keys with Stay/Away buttons, and who wish to have their panel armed at all times.

NOTE: If Function Keys require the entering of an access code, a valid access code must be entered to toggle between arming modes. The access code used to perform this function will be logged with “User Log User XX”. Swinger Shutdown will be reset if the Away button is pressed while the system is armed.

Inhibit Arming EN

All troubles on the panel will prevent the system from arming and it will force the Ready LED to shut off. Press [9] in the Trouble Menu to clear Troubles.

NOTE: With this feature disabled, Bell Trouble will still inhibit arming.

Disarming

To disarm the panel, enter the premises through the designated entry/exit door. The keypad will emit a steady beep to warn that you must disarm the system. During the last 10 seconds of entry delay the panel will pulse the keypad beeper on and off rapidly to warn the entry delay is about to expire.

Enter a valid Access Code at the keypad. If an error is made, re-enter the code correctly. When a correct code is entered the keypad will turn off the ‘Armed’ light and stop the keypad buzzer.

If an alarm occurred while the panel was armed the ‘Memory’ light and the zones which caused the alarm will be flashing. Press the [#] key to return the keypad to the Ready state.

Event Buffer (Event Log)

The panel will store the last 500 events that have occurred on the system. Each event will contain the time, date, partition and the event itself along with the zone number, access code number or any other information pertaining to the event.

If the Event Buffer Follows Swinger Shutdown feature is enabled (Section [013], option 7) the event buffer will not store events after the swinger shutdown level has been reached. This will prevent the panel from overwriting the entire buffer if a problem exists. The event buffer can be viewed three different ways. It can be viewed through an LCD keypad, printed on-site using the PC5400 printer module or it can be uploaded through the DLS software.

Viewing the Event Buffer

The following is the procedure for viewing the event buffer through the LCD keypad:

Step 1 — Enter [*] [6] [Master/Access Code]

Step 2 — Select ‘View Event Buffer’

The keypad will display the Event Number, Partition, Time and Date of the event in question. Use the [*] key to toggle between this information and the event itself. Use the arrow keys (< >) to scroll through the events in the buffer. When you have finished viewing the event buffer press the [#] key to exit.

NOTE: When viewing events for partitions 3 to 8 on an LCD5500 v2.x and lower keypad, they will show as being logged in the “System Area”.

4.2 [*] Commands

[*][1] Zone Bypassing

Users can bypass individual zones using the [*][1] keypad command. This command can be used if users want to have access to an area while the Partition is armed, or to bypass a defective zone (bad contact, damaged wiring) until service can be provided.

A bypassed zone will not cause an alarm.

When the partition is disarmed, all zones that were bypassed using [*][1] will be unbypassed, except for 24-hr zones.

If the Code Required for Bypass option is enabled, an access code will be required to enter the Bypass mode. Only access codes with the Bypass attribute enabled will be able to bypass zones (see section ’[*][5] Programming Access Codes’ ).

Bypassing Zones with an LCD keypad:

Start with disarming the system.

1.Press [*] to enter the function menu. The keypad will display “Press [*] for < > Zone Bypass”.

2.Press [1] or [*], then your [access code] (if required). The keypad will display “Zone Search < > Zone Name”.

3.Enter the two-digit number of the zone(s) to be bypassed (01-64). You can also use the < > keys to find the zone to be bypassed, and then press [*] to select the zone.

The keypad will display “Zone Search < > “Zone Name?”. “B” will appear on the display to show that the zone is bypassed. If a zone is open (e.g., door with door contact is open), the keypad will display “Zone Search < > “Zone Name” O”. If you bypass the open zone, a “B” will replace the “O”.

4.To unbypass a zone, enter the two-digit number of the zone(s) to be bypassed (01-64). You can also use the < > keys to find the zone, and then press [*] to select the zone. The “B” will disappear from the display to show that the zone is no longer bypassed.

5.To exit bypassing mode and return to the Ready state, press [#].

Bypassing Zones with a LED/ICON keypad:

Start with disarming the system

1.Press [*][1], then your [access code] (if required).

2.Enter the two-digit number of the zone(s) to be bypassed (01-64). On LED keypads, the zone light will turn on to indicate that the zone is bypassed.

3.To unbypass a zone, enter the two-digit number of the zone (01-64). On LED keypads,the zone light will turn off to indicate that the zone is not bypassed.

4.To exit bypassing mode and return to the Ready state, press [#].

Other Bypass Features:

The following features are also available on the [*][1] zone bypassing menu:

Bypass Recall: Press [99] while in the [*][1] menu to recall the last set of bypassed zones.

Clear Bypasses: Press [00] while in the [*][1] menu to clear all bypassed zones.

Bypass Groups: Users can program a group of zones to be bypassed (bypass group). Each partition can have a different bypass group. To program a bypass group, in the [*][1] menu, select the zones to be bypassed. Press

[95]to save the group. To recall the group, press [*][1] followed by [91].

If the Code Required for Bypass option is enabled, the Master code or Supervisor codes must be used to access this feature.

NOTE: The zone attribute for zone bypassing must be enabled (see Section [101]-[164] Zone Attributes, Option 4).

NOTE: Hold-up zones should not be part of Bypass Groups.

NOTE: A zone that is manually bypassed via [*][1] will bypass the alarm, fault, and tamper conditions when DEOL is used.

NOTE: If a 24-hour zone is bypassed, ensure that the zone is restored or disabled before removing the bypass.

Code required for bypass . . . . . . . . . . . . . Section [015], Option [5]

[*][2] Trouble Display

The panel constantly monitors itself for several different trouble conditions. If a trouble condition is present, the Trouble light will be ON and the keypad will beep twice every 10 seconds. The trouble beep can be silenced by pressing any key on any keypad. If Bell Squawk on Trouble is enabled (section [014], option[5]), the bell will squawk every 10 seconds when a trouble condition is present.

NOTE: If there is an AC trouble, the keypad will not beep for a General System Trouble.

To view trouble conditions from an LED or ICON keypad:

1.Press [*][2] to enter the trouble menu.

2.The keypad will flash the Trouble light. The zone indicator lights corresponding to the present trouble conditions will be ON.

.

Light

Trouble

Light [1]

Service Required: Press [1] to determine the specific trouble. Lights 1 — 8 will light up to indicate the trouble:

Light [1]

Low Battery: Main panel backup battery charge is low (below 11.5 volts under load).Trouble is restored when the battery charges over

12.5 volts.

Light [2]

Bell Circuit Trouble: The bell circuit is open (see section 2.2 ’Terminal Descriptions’ ).

Light [3]

General System Trouble: One or more of the following troubles has occurred: the PC5204 Power Supply module has an AUX failure,

PC5204 Output #1 Trouble, Home Automation Trouble on the Escort5580(TC), or a printer connected to the PC5400 Printer module has a fault and

is off-line, or T-Link Troubles. Users can view specific conditions in the Event Buffer.

Light [4]

General System Tamper: Tamper has been detected from a module.

Light [5]

General System Supervisory: The panel has lost communication with a module connected to the Keybus (See section 2.8 ‘Confirming

Module Supervision‘ on page 8). The event buffer will log the event.

Light [6]

RF Jam: Please refer to the PC5132 Installation Manual for more information.

Light [7]

PC5204 Low Battery: The PC5204 module has a low backup battery.

Light [8]

PC5204 AC Failure: The PC5204 module has lost AC power.

NOTE: If you remove and then restore power to the main panel in order to service any PC5204 module, or any module being powered by a

PC5204, you must also remove and then restore power to the PC5204 and any connected modules. This ensures that any troubles present

on the module are correctly logged and/or annunciated.

Light [2]

AC Failure: AC power is no longer being supplied to the control panel. The Trouble light will flash if an AC Failure is present, if the Trouble Light

Flashes if AC Fails option is programmed (section [016], option [2]). This trouble will not be displayed if the AC Trouble Displayed option is disabled

(section [016], option [1]).

Light [3]

Telephone Line Monitoring Trouble (TLM): There is a problem with the telephone line. If the system has an Alternate Communicator, this trouble

can be reported to the central station by programming reporting codes in sections [345] and [346].

Light [4]

Failure to Communicate (FTC): The communicator failed to communicate with any of the programmed telephone numbers (see section 5.6 ‘Com-

municator Programming’).

Light [5]

Zone Fault (including Fire Zone): A zone on the system is experiencing trouble, meaning that a zone could not provide an alarm to the panel if

required to do so (e.g. a fire zone is open, or there is a short on a DEOL zone, or a supervisory fault on a wireless zone). When a zone fault occurs,

the keypad(s) on the system will start to beep. Press [5] while in Trouble mode to view the affected zones.

NOTE: A Fire zone trouble will be generated and displayed in the armed state.

Light [6]

Zone Tamper: A zone configured for Double End Of Line resistor supervision has a tamper condition, or the tamper switch is open on a wireless

device. When a tamper condition occurs, the keypad(s) will start to beep (if the system is armed, an alarm will occur). Press [6] while in the Trouble

mode to view the affected zones. If a zone is tampered or faulted, it must be fully restored to clear the trouble.

Light [7]

Device Low Battery/RF Delinquency: A wireless device has a low battery condition. Press [7] one, two, or three times to view which devices are

experiencing battery failure. Press the [7] key an additional time to view zones in RF Delinquency trouble. An LED keypad will indicate battery failure

using zone lights. The following will occur:

Keypad beeps:

Keypad displays:

Press [7]

1

Zones with low batteries (LED keypad — zone lights 1 to 32)

Press [7] again

2

Handheld keypads with low batteries (LED keypad — zone lights 1 to 4)

Press [7] again

3

Wireless keys with low batteries (LED keypad — zone lights 1 to 16)

Press [7] again

4

Zones in RF Delinquency trouble (LED keypad — zone lights 1 to 32)

Light [8]

Loss of System Time: When the panel is powered up, the internal clock needs to be set to the correct time. This trouble is cleared when an attempt

is made to reset the clock. This is set in [*][6] [Master Code] Programming on page 16.

Trouble Menu Acknowledgement EN

Press [9] for Trouble Menu Acknowledgement. This will acknowledge and override existing troubles so the system can be armed. An override event will also be generated and logged, identifying the user. To override open zones, use the Zone Bypass feature [*][1].

If a zone fault/tamper occurs, press [*][2][9] to override the trouble, then [*][1] to override the open zone.

NOTE: When using the Trouble Menu Acknowledgement feature, Section [022] Option 3 has to be enabled.

When using an LCD keypad, the trouble conditions will be listed on the display. Users can scroll through the list of present trouble conditions using the arrow (< >) keys.

NOTE: Troubles can be viewed while armed using the LCD keypad, provided the keypad is version 2.0 or later. Older keypads will incorrectly display “Fire Trouble”. If using older LCD keypads, program section [013], option [3] as OFF to ensure that troubles are displayed correctly.

NOTE: If a trouble is present when the system is armed, the trouble LED will remain on during Exit Delay but will turn off once the exit delay timer expires.

[*][3] Alarm Memory

The ‘Memory’ light will be on if any alarm occurred during the last armed period or if an alarm occurred while the panel was disarmed (24 hour zones). Press [*][3] to view zones in alarm memory. To clear the memory, arm and disarm the system.

[*][4] Door Chime On/Off

If enabled the keypad will beep 6 times rapidly when a zone is tripped and restored. The panel will only do this for zones with the Door Chime attribute enabled and if the door chime feature is enabled. The door chime attribute for each zone is programmed in sections [101] to [164].

[*][5] Programming Access Codes

Access codes are required in order to perform various functions on the system such as arm, disarm, activate command outputs etc.

Program New Access Code

To program an access code enter [*][5][Master Code] followed by a two digit number corresponding to the access code you want to program, then enter a new access code.

The available access codes are as follows:

General Access Codes — Access Codes [01] to [32]

Each access code can be used to arm and disarm the assigned partitions. Additional access code attributes are also programmable to determine what abilities the code will have. You can program partition assignments and access code attributes by following the instructions in this section.

Supervisor Codes — Access Codes [41] and [42]

Supervisor Codes can program additional access codes. By default, Supervisor codes have the same partition and attribute programming as the Master code. You can change the partition and attribute programming for these codes by following the instructions in this section.

System Master Code — Access Code [40]

By default the System Master Code is enabled to operate on all partitions and can perform any keypad function. This code can be used to program all access codes, including the Supervisor Codes and Duress Codes.

If the Master Code Not Changeable option is enabled the System Master Code can only be changed using Installer Programming.

NOTE: EN For EN installations the installer will not have

access to Master Code Programming. In order to return the master code to the factory default setting enter the Special Installer Function [989][Installer’s Code][989] (Master Code Factory Default Programming). This will allow the installer to default the Master Code.

Duress Codes — Access Codes [33] and [34]

Duress codes are standard user codes that will transmit the Duress Reporting Code whenever the code is entered to perform any function on the system.

NOTE: Duress codes are not valid when entering [*][5], [*][6] or [*][8] sections.

NOTE: Duress codes cannot be programmed as a duplicate of another code or as a “Code + 1”.

Maintenance Code

The maintenance code can only be used to arm and disarm the system. It cannot be used to bypass zones, to access the Escort5580(TC), or to cancel or postpone automatic arming. The code can only be programmed in Installer’s Programming. The Maintenance code cannot bypass zones, use [*][9] to arm the system, cancel auto-arming, or perform [*][7] command functions. There will be no arm/disarm bell squawks when the Maintenance code is used.

Guard Code C

The Guard Code can arm the panel at any time. However, the Guard code can only disarm the system after an alarm, tamper, fault or trouble condition has occurred. It can also be used to bypass zones and activate Command Outputs. The Guard Code may be programmed in Section [008].

Arming and disarming using the Guard Code will log as «Closing (Opening) by Maintenance Code». If a Command Output that requires a code is activated with the Guard Code, no User Log will be made. When zones are bypassed with the Guard Code, the panel will log «[*][1] Access by User».

NOTE: The Latching Trouble feature should be used with the Guard Code feature in order disarm with Trouble Present.

Partition Assignments and Access Code Attributes

You can enable or disable each access code to work on each partition. Additional access code attributes are also programmable. Attributes determine what abilities the code will have.

By default, each code has the attributes of the code used to program it. For example, if you use the Master code to program other access codes, the new codes will have the same attributes as the Master code. You can change the partition and attribute programming by following the instructions described below.

You cannot change Master code partition or attribute programming. The Master code has all partitions and all attributes turned on, except for the Bell Squawk on Arming/ Disarming and One Time Use Code Attributes.

Access Code Partition Assignment

To program which partition(s) each code will work on:

1.Enter [*][5][Master Code][8] for partition programming.

2.Enter the 2-digit number of the access code you want to edit.

3. Enter the partition number (1-8) to toggle it on or off.

NOTE: Partition programming is NOT supported by the following keypads: PC5508(Z), PC5516(Z), PC5532(Z) versions v2.00 and lower; LCD5500(Z) version 2.x and lower; LCD5501Z version 1.x and lower.

Access Code Attributes

To program each attribute:

1.Enter [*][5][Master Code][9] for attribute programming.

2.Enter the 2-digit number of the access code you want to edit.

3.Enter the attribute number to toggle it on or off.

Programmable Attributes

Attribute Description

[1]For Future Use

[2]For Future Use

[3]Zone Bypass enabled.

This attribute allows the user to bypass zones.

[4]Escort5580(TC) Remote Access

This attribute allows the user to access the security system via the Escort, if installed.

[5]For Future Use

[6]For Future Use

[7]Bell Squawk on Arming/Disarming. When this attribute is ON, the bell will squawk when the access code is entered to arm or disarm the system. For example, you can use the arm/disarm bell squawk attribute to have wireless key access codes squawk the bell, while other codes are silent. To do this, enable attribute [7] on all access codes associated with wireless keys.

[8]One Time Use Code. This attribute will only affect Access Codes 01-16. If the panel is disarmed with this code, the code will be erased at the end of the Exit Delay the next time that the panel is armed, regardless of which code is used to arm the system. The code will also be erased at the end of the Exit Delay when used to arm the panel. If the panel is disarmed during the Exit Delay when armed with a One Time Use Code, it will still be valid after the next time the panel is armed (unless the same One Time Code is used to arm the second time).

NOTE: If you enable the Bell Squawk on Arming/Disarming option (section [014], option [1]), the bell will sound arm/ disarm bell squawks for all access codes, regardless of the programming for attribute [7] (see Section 5.3 Basic Programming PWS Sect 3 [001]-[004] (see Section 5.4 ‘Advanced Programming’).

Installer’s Programming — Codes and Options

There are three codes which can be programmed by the installer in Installer’s Programming: the Installer’s code,

Master Code and a Maintenance Code/Guard Code. All other access codes can be programmed through the [*][5] command, as described previously in this section.

The master code can also be programmed by the user as access code (40). However, if the Master Code Not Changeable option is enabled, the master code can only be accessed in Installer’s Programming.

General access codes can arm and disarm the system. When the Code Required for Bypassing option is enabled, users will need to enter a valid access code in order to bypass zones. Individual access codes can have the Zone Bypassing attribute disabled under Access Code Attribute programming, as described previously in this section.

If the 6-Digit User Access Codes option is enabled, all the access codes are programmed with six digits instead of four. The Installer’s Code will become [555555]. If 4-digit codes are already programmed and this option is selected, the first four digits of the programmed codes will remain as programmed and the last two digits will be [00].

If the 4-Digit User Access Codes is selected, all codes will be 4-Digits in length, with the exception of the Panel ID code and the Downloading Access Code. If 6-digit codes were

previously programmed and this option is enabled, the first four digits of each code will be used.

Installer’s Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [006] Maintenance Code . . . . . . . . . . . . . . . . . . . . . . . . . . Section [008] Master Code Not Changeable . . . . . . . . . . . . . . . Section [015]: [6] Code Required for Bypassing . . . . . . . . . . . . . . . Section [015]: [5] 6-digit User Access Codes . . . . . . . . . . . . . . . . . . Section [701]: [5]

NOTE: Only one keypad at a time can use [*][5] programming.

[*][6] User Functions

NOTE: Only one keypad at a time can use [*][6] programming.

To program user functions, perform the following:

1.Press [*][6][Master Code]. The keypad will flash the ‘Program’ light.

2.Press the number [1] to [8] for the item to be programmed.

[1] — Time and Date

Enter 4 digits for 24 Hour System Time (HH-MM). Valid entries are 00-23 for the hour and 00-59 for minutes. Enter 6 digits for the Month, Day and Year (MM-DD-YY)

[2] — Auto-arm Enable/Disable

Pressing [2] while in the User Function menu will enable auto-arm (3 beeps) or disable auto-arm (one long beep). The auto-arm feature needs to be enabled on each partition individualy. With this feature enabled, the panel will automatically arm in the Away mode (Stay Away zones active) at the scheduled time. The auto-arm time is programmed with the [*][6][Master Code][3] command.

[3] — Auto-arm Schedule

Enter [3] to change the Auto-arm time for each day of the week. Scroll to the day of the week you want to change, or enter the number of the day (1-7 for Sunday to Saturday). On an LED keypad, zone lights 1-7 will represent Sunday to Saturday.

When you have selected a day, enter the Auto-arm time in 24-hour format (i.e. enter a 4-digit number in [hhmm] format).

The system will return you to the day selection menu. Scroll to the next day you want to program, or to exit auto-arm programming, press [#].

NOTE: To change the auto-arm schedule at another partition, users with access to that partition will have to select the partition on the keypad before entering the auto-arm schedule menu.

NOTE: Only LCD5500 v2.0 or greater keypads support the [*][6][3] menu option.

[4] — System Test

When System test is initiated the panel will perform the following.

Sound the alarm output for two seconds

Light all lights and display pixels on the keypad

Sound the keypad buzzer for two seconds

Test the main panel/PC5200/PC5204 battery

Send a System Test Reporting code, if programmed.

[5] — Enable DLS / Allow System Service

If enabled, the installer will be able to access Installer Programming by DLS. In case of DLS access this provides a window where rings will be detected by the panel. The DLS window will remain open for 6hrs, during which time the installer will be able to enter DLS an unlimited number of times. After the 6-hr window has expired, Installer’s Programming will be unavailable again until the window is re-opened.

[6] — User Initiated Call-Up

When [6] is pressed, the panel will initiate a call to the

downloading computer. The panel will make 1 attempt to call the downloading computer.

NOTE: The downloading computer must be waiting for the panel to call before downloading can be performed.

[7] — For Future Use

[8] — User Walk Test EN

[*][6] User Functions allows the user to enable/disable the User Walk Test mode. The User Walk Test functionality and operation are based on the Installer Walk Test however there are some relevant differences between them regarding fire zone violation handling or communication during the test. Fire zones, [F] Key and 2-wire Smoke Detectors are excluded from User Walk Test. If any of these zones is violated or activated during User Walk Test, the system will exit from Walk Test mode and generate an alarm condition for the violated fire zone. To provide support for event communication new Programming Sections are added for the Walk Test Begin/End reporting codes.

The User Walk Test mode operates with a 15 minute time out. If there is no zone violation for 15 minutes, the system restores from User Walk Test mode.

The Bell will sound a squawk instead of a 2-second pulse.

LCD Keypad User Functions

Additional features are available using on the LCD keypad. These features do not have numbers assigned. Use the arrow keys (< >) to scroll through the [ ][6] menu and press the [ ] key to select the following commands.

View Event Buffer: The 500 Event Buffer can be viewed through any LCD keypad.

Brightness Control: When this option is selected the keypad will allow you to scroll through 10 different backlight level options. Use the arrow keys (<>) to scroll to the desired backlight level and press the [#] key to exit.

Contrast Control: When this option is selected the keypad will allow you to scroll through 10 different contrast level options. Use the arrow keys (< >) to scroll to the desired contrast level and press the [#] key to exit.

Keypad Buzzer Control: When this option is selected the keypad will allow you to scroll through 21 different keypad sounder tone options. Use the arrow keys (< >) to scroll to the desired keypad beeper level and press the [#] key to exit. This function can be achieved on LED keypads by holding the [*] key.

[*][7] Command Output Functions

There are four output functions available to the user. Entering [*][7] [1-4] [Access Code, if required] will activate any output programmed as [19]-[22] (respectively). Each function can be performed when the system is either armed or disarmed.

[*][8] Installer Programming

Enter [*][8] followed by the Installer Code to enter Installer Programming.

[*][9] Arming Without Entry Delay

When a partition is armed with the [*][9] command the panel will remove the entry delay from the partition. After the exit delay, Delay 1 and Delay 2 type zones will behave as instant and Stay/Away zones will remain bypassed. The entry delay can be activated or deactivated at any time while the system is armed by pressing [*][9].

NOTE: If the panel is armed using [*][9], disarming will only be possible from the keypad inside the premises.

NOTE: Global Delay zones will always have an entry delay, even if the system is armed using [*][9].

[*][0] Quick Arm

If the Quick Arm Enable option is enabled the panel can be armed by entering [*][0]. This is a useful method of arming a Partition when someone without a access code will be required to arm a Partition.

NOTE: The Quick Arm feature must be enabled in order for the Stay/Away function keys to operate as intended. If the feature is not enabled, the user will be required to enter their access code after pressing the Stay or Away function key in order to arm the system in the stay or away mode.

[*][0] Quick Exit

Quick Exit will allow someone to leave an armed premise through a Delay type zone without having to disarm and rearm the system.

When [*][0] is entered, if the Quick Exit Enabled option is enabled, the panel will provide a two minute window to exit. During this time the panel will ignore the first activation of a Delay type zone. When the Delay zone is secured the panel will end the two minute time period.

If a second Delay zone is tripped, or if the zone is not restored after two minutes, the panel will start entry delay.

NOTE: If Quick Exit is used on a partitioned system, Keypad Blanking and Access Code Required to Remove Blanking should be enabled.

Quick Arm Enable . . . . . . . . . . . . . . . . . . Section [015], Option [4] Quick Exit Enable. . . . . . . . . . . . . . . . . . . Section [015], Option [3]

4.3 Function Keys

There are 5 function keys on the PC1616/PC1832/PC1864 keypads. The function is activated by pressing and holding the key for 2 seconds. The programming of any function key on any keypad may be changed to one of the options listed below. (See section 2.7 ‘Keypad Assignment‘ on page 7 for instructions on changing function key programming.)

[00] — Null Key

The key is not used and will perform no function when pressed.

[01] — Select Partition 1

Provides an easy way to select Partition 1. This is the same as pressing and holding the [#] key then pressing and holding the [1] key to select Partition 1 (see section 4.4 ’Global and Partition Keypad Operation’ ).

[02] — Select Partition 2

Provides an easy way to select Partition 2. This is the same as pressing and holding the [#] key then pressing and holding the [2] key to select Partition 2 (see section 4.4 ’Global and Partition Keypad Operation’ ).

[03] — Stay Arm

Arms the partition to which the keypad is assigned. All Stay/ Away type zones will be automatically bypassed. Delay type zones will provide entry and exit delay. The Quick Arm feature must be enabled for this key to function (Section [015], Option [4]). If Quick Arming is not enabled, the user must enter their access code after pressing the function key in order to arm the system in the Stay mode.

[04] — Away Arm

Arms the partition to which the keypad is assigned. All Stay/ Away type zones will be active at the end of the exit delay. Delay type zones will provide entry and exit delay. The Quick Arm feature must be enabled for this key to function (Section [015], Option [4]). If Quick Arming is not enabled, the user must enter their access code after pressing the function key in order to arm the system in the Away mode.

[05] — [*]+[9] No-Entry Delay Arm

After this function key is pressed the user must enter a valid access code. The Partition will arm and remove entry delay

from the partition when the exit delay expires (see section ’[*][9] Arming Without Entry Delay’ ).

[06] — [*]+[4] Door Chime On/Off

Pressing the key will toggle the Door Chime feature ON or OFF. One solid beep means the feature has been disabled, three short beeps means it has been enabled.

[07] — [*]+[6]…[4] System Test

This function key provides the user with a simple method for testing the system (see section ’[*][6] User Functions’ ). A valid Master Code is required to perform this command.

[08] — [*]+[1] Bypass Mode

This function key provides the user with a simple method for entering the Bypass Mode. If a access code is required it must be entered before bypassing can be performed (see section ’[*][1] Zone Bypassing’ ).

[09] — [*]+[2] Trouble Display

This function key provides the user with a simple method for entering the Trouble Display Mode (see section ’[*][2] Trouble Display’ ).

[10] — [*]+[3] Alarm Memory

This function key provides the user with a simple method for entering the Alarm Memory Display Mode (see section ’[*][3] Alarm Memory’ ).

[11] — [*]+[5] Programming Access Codes

This function key provides the user with a simple method for programming access codes. After this key is pressed a valid System Master or Supervisor Code will have to be entered before the panel will allow programming to be performed (see section ’[*][5] Programming Access Codes’ ).

[12] — [*]+[6] User Functions

This function key provides the user with an easy method for programming user functions. After keys are pressed a valid System Master or Partition Master must be entered before the panel will allow user functions to be performed (see section ’[*][6] User Functions’ ).

[13] — [*]+[7]+[1] Command Output Option 1

This function key provides the user with a simple method for activating a PGM Output programmed as Command Output Option 1 (See Section 5.8 Programmable Output Programming PWS Sect 8). By default, after this key is pressed a valid access code must be entered (see section ’[*][7] Command Output Functions’ ).

[14] — [*]+[7]+[2] Smoke Detector Reset

Pressing this key will cause the panel to activate for 5 seconds any output programmed as Sensor Reset. (see section ’[*][7] Command Output Functions’ ).

[15]— For Future Use

[16]— [*]+[0] Quick Exit

Pressing this key will cause the panel to activate the Quick Exit feature (see section ’[*][0] Quick Exit’ ).

[17] — [*]+[1] Reactivate Stay/Away Zones

This function key provides the user with a simple method for adding Stay/Away zones back into the system (see section ’[*][1] Zone Bypassing’ ).

[18]— For Future Use

[19]— [*]+[7]+[3] Command Output 3

This function key provides the user with a simple method for activating a PGM Output programmed as Command Output Option 3

Loading…

DSC PowerSeries PC1616 User Manual

  • Contents

  • Table of Contents

  • Bookmarks

Quick Links

WARNING: This manual contains information on limitations regarding

product use and function and information on the limitations as to liability of

the manufacturer. The entire manual should be carefully read.

PC1616/PC1832/PC1864

User Manual

v4.6 and higher

loading

Related Manuals for DSC PowerSeries PC1616

Summary of Contents for DSC PowerSeries PC1616

  • Page 1
    WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. PC1616/PC1832/PC1864 User Manual v4.6 and higher…
  • Page 3: Table Of Contents

    Table of Contents About Your Security System ……….1 PowerSeries System Keypads .

  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electric shock and/or injury, observe the following: Do not spill any type of liquid on the equipment. • Do not attempt to service this product yourself. Opening or removing the cover may expose •…

  • Page 5: About Your Security System

    General System Operation Your security system is made up of a DSC control panel, one or more keypads and various sensors and detectors. The control panel will be mounted out of the way in a utility closet or in a basement.

  • Page 6: Powerseries System Keypads

    PowerSeries System Keypads PK5508/PK5516/RFK5508/RFK5516 PC1555RKZ Status Lights Number Zone Lights PK5500/PK5501/RFK5500/RFK5501/RFK5564 Emergency Keys Stay Away Chime Reset Quick Exit LED5511 LCD5511 Display System Lights Number…

  • Page 7: Keypad Display Symbols

    Keypad Display Symbols LCD5501 Fixed Message LCD5501 ICON PK5501/RFK5501 LCD5511 PK5508/5516/RFK5508/5516 LED5511 Clock Digits 1, 2 – These two 7 segment clock digits indicate the hour digits when the local clock is active, and identify the zone when the OPEN or ALARM icons are active. These two dig- its scroll one zone per second from the lowest zone number to the highest when scrolling through zones.

  • Page 8: Pk5500/Rfk5500/Rfk5564 Language Selection

    IMPORTANT NOTICE A security system cannot prevent emergencies. It is only intended to alert you and, if included, your central station of an emergency situation. Security systems are very reliable but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance.

  • Page 9: Stay Arming (Partially Turning On / Part Setting)

    Disarming Error If your code is invalid, the system will not disarm and a 2-second error tone will sound. If this hap- pens, press [#] and try again. Stay Arming (Partially Turning On / Part Setting) Ask your alarm company if this function is available on your system. Stay arming will bypass the interior protection (i.e.

  • Page 10: When Alarm Sounds

    When Alarm Sounds The system can generate 4 different alarm sounds: • Temporal / Pulsed Siren = Fire Alarm • 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide Alarm • Continuous Siren = Intrusion (Burglary Alarm) NOTE: The priority of signals is fire alarm, carbon monoxide alarm then burglary alarm. Intrusion (Burglary) Alarm Continuous Siren f you are unsure of the source of the alarm approach with caution! If the alarm was acciden- tal, enter your Access Code to silence the alarm.

  • Page 11
    Bypassing Zones with a PK5500/RFK5500/RFK5564 Start with disarming the system. 1. Press [,] to enter the function menu. The keypad will display “Press , for < > Zone Bypass”. 2. Press [1] or [,], then your [access code] (if required). The keypad will display “Zone Search < > Zone Name”.
  • Page 12: Trouble Conditions

    Trouble Conditions When a trouble condition is detected, the Trouble ( ) or System indicator will turn on, and the key- pad will beep every 10 seconds. Press the key to silence the beeps. Press [,][2] to view the trouble condition.

  • Page 13: Access Codes

    When using the PK5500/RFK5500/RFK5564, use the [<][>] keys to find the specific code and press [,] to select. Enter the new 4 or 6-digit access code, or press [,] to erase it. When programming is complete, enter another 2-digit code to program or press to exit.

  • Page 14: Bell Squawk Attribute

    Bell Squawk Attribute This attribute is used to determine whether an access code should generate an arming/disarming Bell Squawk upon entry of the code for Away arming. The wireless keys with access codes associated with them may generate Arming/Disarming Bell squawks. If desired, this option may be used with codes that are manually entered.

  • Page 15: Changing Brightness/Contrast

    At the selected auto-arm time, the keypad buzzers will sound for a programmed amount of time (programmable by the installer only) to warn that an auto-arm is in progress. The bell can also be programmed to squawk once every 10 seconds during this warning period. When the warning period is complete, the system will arm with no exit delay and in the Away Mode.

  • Page 16: Changing The Buzzer Level

    PK5501/PK5508/PK5516/RFK5501/RFK5508/RFK5516 keypads When this option is selected, the keypad will allow you to scroll through 4 different backlighting lev- els. A level of 0 disables the backlighting. 1. Press [,][6][Master Code]. 2. Use the [>] right scroll key to move through the 4 different backlighting levels. 3.

  • Page 17: Testing Your Keypad Sounder And Siren

    Testing Your Keypad Sounder and Siren The System Test provides several system tests, and a two-second check of the keypad sounder and bell or siren. 1. Press [,][6][Master Code][4]. 2. The following will occur: — The system activates all keypad sounders and bells or sirens for 2 seconds. All keypad lights turn ON. — PK5500/RFK5500/RFK5564 keypads will light all pixels — The Ready, Armed, and Trouble LED’s will flash for the duration of the test 3.

  • Page 18: Reference Sheets

    Reference Sheets Fill out the following information for future reference and store this guide in a safe place. System Information Enabled? FIRE AUXILIARY PANIC The Exit Delay Time is _______ seconds. The Entry Delay Time is _______ seconds. For Service Central Station Information Account#: ___________________ Telephone#: __________________ Installer Information :…

  • Page 19
    PC1832/PC1864 Code Access Code Code Access Code Code Access Code Code Access Code PC1864 Code Access Code Code Access Code Code Access Code Code Access Code Sensor / Zone Information Sensor Protected Area Sensor Type Sensor Protected Area Sensor Type…
  • Page 20: Guidelines For Locating Smoke Detectors And Co Detectors

    Sensor Protected Area Sensor Type Sensor Protected Area Sensor Type Guidelines for Locating Smoke Detectors and CO Detectors The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke and CO alarms. Smoke Detectors Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.

  • Page 21: Carbon Monoxide Detectors

    Where required by applicable laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms shall be installed as follows: (1) In all sleeping rooms and guest rooms. (2) Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a sleeping room, the distance measured along a path of travel.

  • Page 22: Household Fire Safety Audit

    Household Fire Safety Audit Read this section carefully for important information about fire safety. Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit be conducted and a fire escape plan be developed. 1.

  • Page 23: Keypad Quick Guide

    Keypad Quick Guide The following table summarizes the keys, indicators, and most often used commands of the keypad. Status Lights Ready — Must be on to arm system. All zones must be secured or bypassed and the system disarmed for this light to activate. Armed — Indicates system is armed.

  • Page 24
    Press [<][>]buttons to scroll to user code. Enter [Master Code][9][xx] to enter the user code (xx = 1-16). [1] Supervisor’s Code [2] Duress Code Program User Codes [3] Zone Bypassing Change Attributes [4] Remote Access [5]-[6] Future Use [7] Bell/Siren Squawk Output [8] One Time Use Code User Commands Event Buffer…
  • Page 25: Warning Please Read Carefully

    WARNING Please Read Carefully N o te t o Insta llers positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other This warning contains vital information. As the only individual in side of closed doors.

  • Page 26: Important Information

    DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122 — Re-orient the receiving antenna. Additional Information — Increase the separation between the equipment and receiver.

  • Page 27: New Zealand Telecom Network

    Decadic signalling should not be used as it is being progressively phased out of (f) Termination — Without prejudice to any other rights, DSC may terminate this EULA if You fail to the network. DTMF dialling is 100% available and it should always be used.

  • Page 28
    Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative. © 2012 Tyco International Ltd. and its Respective Companies. All Rights Reserved Toronto, Canada www.dsc.com   Printed in Canada…

Понравилась статья? Поделить с друзьями:
  • Инструкция по работе в битрикс 24 для сотрудников
  • Инструкция по прокачке амортизаторов kyb
  • Инструкция по противопожарной защите угольных шахт 2021
  • Инструкция по программированию брелков дорхан
  • Инструкция по работе в ацк госзаказ нижегородская область