Коса штиль fs 55 инструкция по эксплуатации

1. Manuals
2. Brands
3. Stihl Manuals
4. Trimmer
5. FS 55
6. Instruction manual

• Page 1
  STIHL FS 55 Instruction Manual…

• Page 3: Table Of Contents

  Minimize Wear and Avoid Damage Main Parts Specifications Maintenance and Repairs This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 4: Techniques

  Secure it against unauthorized use. Intake air: Winter operation The user is responsible for avoiding injury to third parties or damage to their property. Handle heating FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 5
  STIHL or material (e.g. leather). are technically identical. If you have any questions in this respect, consult a FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 6
  To reduce the risk of seri- good condition. the engine until leak is fixed. ous burn injuries, avoid touching hot parts of the machine, including the gearbox housing. FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 7
  / stop switch to STOP or 0. securely. The cutting attachment must be clear of the ground and all other obstructions because it may begin to run when the engine starts. FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 8
  – do not run the engine Be particularly alert and cautious when unnecessarily, accelerate the engine wearing hearing protection because only when working. your ability to hear warnings (shouts, alarms, etc.) is restricted. FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 9
  The forces that occur act on and result in serious or fatal injuries. attachment. the machine, the attachment and the material being cut. FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 10
  The force with which the handles starter with the spark plug boot or spark – are held (a tight grip restricts plug removed unless the slide control / circulation). FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 11
  STIHL Polycut Mowing Head with Polymer Blades For mowing unobstructed edges of meadows (without posts, fences, trees or similar obstacles). FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 12
  The risk of kickout is greatest when the parts. black area of the rotating cutting attachment comes into contact with a Resharpen the grass cutting blade solid object. according to instructions when it has dulled noticeably. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 13: Approved Combinations Of Cutting Attachment, Deflector, Handle And Harness

  No other STIHL AutoCut C 25-2 combinations are permitted because of STIHL AutoCut 25-2 the risk of accidents. STIHL TrimCut 31-2 STIHL DuroCut 20-2 FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 14: Mounting The Bike Handle

  18 Full harness may be used Insert screws (7) through the holes in the parts and screw them into the clamp (6) as far as they will go FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 15: Mounting The Loop Handle

  Screw in the bolt (8) and tighten up Fasten the throttle cable NOTICE Do not kink the throttle cable or run it in tight radiuses – the throttle trigger must move freely! FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 16
  Go to «Securing the Loop Handle». barrier bar is fitted – lock the nuts if necessary. The sleeve (9) (not fitted on all models) must be between the loop handle and the control handle. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 17: Fitting The Carrying Ring

  Insert the M6x14 screw (2). Mounting the deflector Line up the carrying ring. Tighten down the screw firmly. Deflectors (1) and (2) are both mounted to the gearbox in the same way. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 18: Mounting The Cutting Attachment

  Machine supplied with mounting Machine supplied without mounting hardware hardware Mowing heads and metal cutting attachments may be mounted. Only mowing heads may be used which mount directly to the shaft (2). FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 19
  Remove the tool used to block the shaft. Use a deflector that matches the cutting attachment – see «Mounting the Removing the Mowing Head Deflector». Block the shaft. Unscrew the mowing head clockwise. FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 20
  (5) will already be mounted. Securing the cutting attachment Fit the thrust washer (6) – convex side must face up. Fit the rider plate (7). FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 21: Fuel

  Gasoline Clean the fuel tank and canister from time to time. Use only high-quality brand-name gasoline with a minimum octane rating of 90 – leaded or unleaded. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 22: Fueling

  Put on the shoulder strap (1). Adjust the length of the strap so that the carabiner (2) is about a hand’s width below your right hip. Balance the machine. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 23: Balancing The Machine

  Move the carrying ring up or down the drive tube – tighten the screw moderately – let the unit go and wait until is its balanced – then check the floating position. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 24: Starting / Stopping The Engine

  START – ignition is switched on – the engine can start F – normal run position – the engine is running or can start STOP-0 – engine off – the ignition is switched off FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 25
  I – normal run position – the engine can start or is running Go to «All versions». 0 – Stop – engine off – the ignition is switched off FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 26
  Do not pull out the starter rope all the not rotate when the engine is idling. way – it might otherwise break. Do not stand or kneel on the drive tube. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 27: Transporting The Unit

  Plug». Move the slide control or stop switch to F / I. Set the choke lever to e – even if the engine is cold. Now start the engine. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 28: Operating Instructions

  For longer out-of- service periods – see «Storing the Machine». FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 29: Adjusting The Carburetor

  A different standard setting is necessary for each of these carburetors. Identifying the Carburetor Use the following illustrations to identify the carburetor installed in your machine and then adjust the carburetor as described: FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 30
  Turn the low speed screw (L) slowly runs smoothly – the cutting clockwise, no further than stop, until attachment must not rotate. the engine runs smoothly and still accelerates satisfactorily. Carburetor 2 FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 31: Spark Plug

  (1), screw the engine damage due to insufficient adapter onto the thread and tighten it lubrication and overheating. down firmly to reduce the risk of arcing and fire. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 32: Engine Running Behavior

  Store the machine in a dry and secure location – out of the reach of children and other unauthorized persons. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 33: Sharpening Metal Cutting Blades

  – and allow it to spring head. balanced as necessary – STIHL back. recommends a STIHL servicing Pull ends of the lines outward. dealer. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 34: Inspections And Maintenance By Dealer

  WARNING If there are signs of serious wear, replace the complete mowing head. The thermoplastic cutting blades are referred to as «blades» in the following. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 35: Maintenance And Care

  Cooling inlets Clean Have checked by servicing dealer Spark arrestor in muffler Have cleaned or replaced by servicing dealer All accessible screws and nuts (not adjust- Retighten ing screws) FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 36
  Visual inspection Cutting attachment Replace Check tightness Metal cutting attachment Sharpen Safety labels Replace STIHL recommends an authorized STIHL servicing dealer. not in all versions, market-specific FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 37: Minimize Wear And Avoid Damage

  Clutch – STIHL recommends that you have Filters (air, fuel) – servicing and repair work carried out exclusively by an authorized STIHL FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 38: Main Parts

  13 Choke lever 14 Air filter cover 15 Tank cap 16 Tank 17 Machine support 18 Loop handle 19 Barrier bar (country specific) 20 Drive tube 21 Stop switch Serial number FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 39: Specifications

  For further details on compliance with Cut-off speed (rated): 10,000 rpm Vibration Directive 2002/44/EC see www.stihl.com/vib. Max. output shaft speed (cutting attachment): 8,100 rpm Ignition System Electronic magneto ignition FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 40: Maintenance And Repairs

  The K-factor in accordance with Directive 2006/42/EC is 2.5 dB(A) for the sound pressure level and sound power level; the K-factor in accordance with Directive 2006/42/EC is 2.0 m/s for the vibration measurement. FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 41: Guide To Using This Manual 2 Disposal

  Directive 2000/14/EC, Annex V, using the ISO 10884 standard. Measured sound power level 108 dB(A) Guaranteed sound power level 110 dB(A) Technical documents deposited at: FS 55, FS 55 C, FS 55 R, FS 55 RC…

• Page 42
  English FS 55, FS 55 C, FS 55 R, FS 55 RC…
• Page 44
  0458-233-0121-F englisch www.stihl.com *04582330121F* 0458-233-0121-F…

Производители

Abocom

AGFA

Genius Products U.S.A.

Green House

Guangzhou Liwei

Microtek

Miranda Camera Co

Mitek

Rowe

Wolverine

Типы устройств

Шлифовальные станки

GPS-навигаторы

Электроника для фитнеса

Велосипеды

Подогрев сидений

Цепперы

Кусторезы

Электроинструменты и освещение

Сеть хранения данных

Топливные системы, терминалы и компенсаторы

Устройства

HP Data Center Environmental Edge

Ikelite Nikon 5400

Impex NS-40504U

Kenmore 7973 REV 06/07

Kicker Impulse I12

Konica Minolta DiMAGE Z2

LG 39LB5600

Moffat GSC 5061

Soleus Air DP1-30-03

Sony SFM1

freeuserguide.ru
About Us
Contacts
Disclamers
Privacy Policy