Кросстренер bowflex max trainer m6 инструкция

Категории

• Contents

• Table of Contents

• Troubleshooting

• Bookmarks

Summary of Contents for Bowflex Max Trainer M6

• 8 Maintenance Parts A B D U G E F G V E T I I H J K Q Q R R O O P P N L M N W S BB DD CC AA Z EE FF GG Y X L C
  

• 27 REPLACEMENT PROCEDURE SKILL LEVEL Level I : Low — very little mechanical knowledge or exposure. Level II : Intermediate — some experience with mechanical procedures Level III : Advanced — knowledgeable about mechanical procedures ! To reduce the risk of electrical shock or unsupervised usage of the equipment, always unplug the power cord from the wall outlet and wait 5 minutes before cleaning, maintainin

• 57 2. Remove the Right Stabilizer Shroud from the machine (if equipped). 3. Using a #2 Phillips screwdriver, remove the indicated (by ovals) screws and only loosen the lowest indicated screw (arrow) from the Right Fan Cover. Note: Loosen the lowest screw by at least 3 full rotations. To assist with assembly, note that the upper screw is a machine screw and not a self-tapping screw. 4. The Right Fan Cover has a tab that needs to be pushed upward to clear the

• 3 SAFETY WARNING LABELS AND SERIAL NUMBER FCC Compliance Changes or modi cations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The machine and power supply comply with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

• 55 26. Grasp the Fan Pulley where the Fan Belt is engaged on it, and forcibly rotate the Fan Pulley until the Fan Belt is fully engaged. Keep ngers out of any pinch opportunities when rotating the Fan Pulley. 27. Put on eye protection and cut the Zip-Tie without damaging the new Fan Belt or Fan Pulley. 28. Installation is the reverse procedure. 29. Final Inspection Inspect your machine to ensure

• 16 NO YES Console Does Not Light Up Completely BEGIN HERE Remove console back cover (8 screws) and check all connec- tions into console (plug and unplug). Be sure the cables are connected securely and oriented properly. The small latch on the connector should line up and snap into place. Peel off the protective plastic film on the display. If the plastic film has already been removed and the problem remains, continue with troubleshooti

• 23 Does the noise persist? Does the noise persist? Noise Issues — Squeaking, Squealing, Creaking or Chirping BEGIN HERE YES Remove the rubber end cap, where the pedal arm connects to the crank arm, on both sides of the machine. Issue resolved. Apply a drop of mineral oil to the bushings on each side of the roller wheel (No need to disassemble) one side at a time. Do NOT apply lubricant directly to the wheel. Catch any excess lubricant with a towel or cloth.

• 37 = Brake Assembly Magnets Brake Disc 18. The Brake Magnets should be aligned with the Brake Disc and cen- tered around the Brake Disc. 19. If the Brake Assembly only needs to be slightly adjusted, loosen the front screw that secures the Brake Assembly using a 10mm hex wrench. Rotate the Brake Assembly until the Magnets are aligned and of equal distance from the Brake Disc. If the Brake Assembly must be fully shif

• 28 Tools Required (not included) #2 Phillips screwdriver 10mm hex wrench 8mm open ended wrench Adjust the Brake Assembly on the Bowflex ™ Max Trainer ™ M6/M8 and M6i/M8i Skill Level: II 8020825.100118.A Replacement Procedure NOTICE: ThisdocumentprovidesinstructionsfortheadjustmentoftheBrakeAssemblyontheBowex™MaxTrainer™M6/M8andM6i/M8imachines. If you need assistance, please contact Customer Service (if purchased in US/Canada) or your local distributor (if purchased outside US/Can

• 25 NOTE: It is OK if the threads in the flange are damaged. The new hardware includes nuts to securely hold pulley in place. YES Upper (Drive) Pulley Contact Customer Care for Advanced Troubleshooting Has the Upper Pulley already been replaced recently? NO Replace the Drive Belt and install the Drive Pulley Kit. YES YES The Drive Pulley is not the cause of the problem. Go to Troubleshooting options. NO NO Begin by inspect

• 48 20. Using a #2 Phillips screwdriver, remove the screws from the Left Shroud. ( 9 screws on the Left Shroud) Remove the upper screws labeled ‘ * ’ last. 21. Using a 4mm hex wrench, remove the screw indicated by “A” from the Drive Belt Tensioner Arm. 22. Using a 8mm hex wrench, loosen the screw indicated by “B” until the Drive Belt is free enough to be removed from the Drive Pulley. Remove the Drive Belt. Keep ngers out of any pinch opportunit

• 62 6. Using a #2 Phillips screwdriver, remove the 3 indicated screws from the Brake Disc. 7. Carefully remove the Brake Disc from the machine. 8. Using a 8mm open ended wrench, loosen the Brake Cable Secur- ing Nut until the Brake Cable can be released from the Servo Motor Arm. 9. Remove the Brake Spring from the Brake Arm. 10. Disconnect the Cables from the Servo Motor. 11. Using a #2 Phillips screwdriver, remove the 4 screws that attach the Servo Motor to the Frame. 12. Attach the new Servo Motor to

• 24 NO YES Contact Heart Rate Issues BEGIN HERE Dry or heavily calloused hands may need a heart rate cream to make better contact. Search for Buh-Bump Heart Rate Cream online. Ensure hands are centered on the Heart Rate (HR) sensors with equal pressure, and as little movement as possible without touching the metal frame. Does the issue persist? Issue resolved. Replace the Cons