Lay z spa palm springs инструкция

www.bestwaycorp.com

www.bestwaycorp.com/support

Visit Bestway YouTube channel

FOR INSTRUCTION VIDEOS PLEASE VISIT

303021185665

SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic

safety precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS — READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: The spa must be supplied through an isolating transformer

or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.

The pump must be tested before each use. To test, follow the instructions in the Pump Test section of this manual.

If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.

To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.

No part of the appliance is to be located above the bath during use.

Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to a person in spa pool; Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa pool.

The plug of pump shall be more than 3.5m away from the spa.

It is necessary to have the plug accessible after installation of the spa.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on and off by the utility.

After using your spa for 3-5 years, you should contact your local qualified maintenance technician to ensure the safety and performance of the spa. The main components, such as heating element, air blower motor and non-return valves within the electric unit should be checked and replaced(if necessary) by professional persons.

Warning: Always keep plug dry, plug in with wet plug is definitely forbidden!

The plug shall be directly connected only to a socket-outlet of the fixed electrical installation.

The spa must be supplied by earthed power source. TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA

WHEN IT IS RAINING. Never wear your contact lenses when in your spa. Do not use spa during chemical maintenance. Extension cords cannot be used. Dont plug or unplug the appliance if your hands are wet. Always unplug the appliance: — on rainy days — before cleaning or other maintenance — if you leave it unattended on holidays When the appliance will be not used for a long time, such

as in the winter, the spa or pool set should be disassembled and stored indoors.

Caution: Read the instructions before using the appliance and every time you install or reassemble the appliance.

Keep the instructions safe. If the instruction is missing, please contact the manufacturer or download a copy from www.bestwaycorp.com

Warning: For electric safety, a PRCD is incorporated in the power cord. If current leakage of more than 10mA is detected, the device will operate and cut off the power supply. In such a case, please unplug and stop using the spa at once. Dont reset the product by yourself. You must contact the local service agent to check and repair the product.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

3

1. Safety Instructions …………………………………………………………………..

2. Assembly ………………………………………………………………………………….

3. Operation ………………………………………………………………………………….

4. Maintenance ……………………………………………………………………………..

5. Troubleshooting ………………………………………………………………………

P3

P9

P10

P12

P15

CONTENTS

QUESTIONS? PROBLEMS? MISSING PARTS?

For FAQ, Manuals Or Spare Parts, Please Visit www.bestwaycorp.com

TO THE STORE

they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (For market other than EU)

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. (For EU market)

Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock;

Water attracts children; always attach a spa cover after each use.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children can not use this spa unless they are supervised at all times.

RISK OF INJURY. Never operate spa if inlet / outlet pipes are broken or missing. Never attempt to replace the inlet / outlet pipes. Always consult your local Aftersales Centre.

RISK OF ELECTRIC SHOCK. Install at least 2m from all metal surfaces.

RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2m of spa.

During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.

TO REDUCE THE RISK OF INJURY: A. The water in a spa should never exceed 40C (104F).

Water temperature between 38C (100F) and 40C (104F) is considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

B. Since excessive water temperatures have a high potential for causing fetal damage during the early months of

pregnancy, pregnant or possibly pregnant women should limit spa water temperature to 38C (100F).

C. Before entering a spa, the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating device varies.

D. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.

E. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.

F. Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

TO REDUCE THE RISK OF INJURY: Never pour water with a temperature higher than 40C (104F) directly into the spa pool.

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level that is several degrees above the normal body temperature of 37C (98.6F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.

Electric installations should follow national wiring rules, consult a qualified electrician with any questions.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS. CAUTION:

The spa should not be setup or left out in temperature lower than 4C (40F).

Do not use the spa alone. People with infectious diseases should not use a spa. Do not use the spa immediately following strenuous

exercise. Always enter and exit the spa slowly and cautiously. Wet

surfaces are slippery. To avoid damage to the pump, the spa must never be

operated unless the spa is filled with water. Immediately leave spa if the user feels uncomfortable or

sleepy. Never add water to chemicals. Always add chemicals to

water to avoid strong fumes or violent reactions that may result in hazardous chemical spray.

Regarding the information pertaining to cleaning, maintenance of water, and disposal of water, please see section «MAINTENANCE».

Regarding the information pertaining to the installation, thanks to refer to the below paragraph of the manual.

NOTE: Please examine equipment before use. Notify Bestway at

the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.

This product is not intended for commercial use.

WARNING FOR ELECTRIC AIR PUMP (For Palm Springs HydroJet): The electric air pump is not a part of spa. You should refer to the user manual of electric air pump for safety. Extension cord used for the air pump when inflating the pool is strictly forbidden to be used for the spa. After inflation of the pool, the air pump, as well as extension cord must be disconnected from supply mains and stored indoor place. Motor run time should not exceed 20 minute CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO WATER OR RAIN. FOR HOUSEHOLD USE ONLY.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic

safety precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS — READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: The spa must be supplied through an isolating transformer

or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.

The pump must be tested before each use. To test, follow the instructions in the Pump Test section of this manual.

If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.

To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.

No part of the appliance is to be located above the bath during use.

Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to a person in spa pool; Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa pool.

The plug of pump shall be more than 3.5m away from the spa.

It is necessary to have the plug accessible after installation of the spa.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a

4

timer, or connected to a circuit that is regularly switched on and off by the utility.

After using your spa for 3-5 years, you should contact your local qualified maintenance technician to ensure the safety and performance of the spa. The main components, such as heating element, air blower motor and non-return valves within the electric unit should be checked and replaced(if necessary) by professional persons.

Warning: Always keep plug dry, plug in with wet plug is definitely forbidden!

The plug shall be directly connected only to a socket-outlet of the fixed electrical installation.

The spa must be supplied by earthed power source. TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA

WHEN IT IS RAINING. Never wear your contact lenses when in your spa. Do not use spa during chemical maintenance. Extension cords cannot be used. Dont plug or unplug the appliance if your hands are wet. Always unplug the appliance: — on rainy days — before cleaning or other maintenance — if you leave it unattended on holidays When the appliance will be not used for a long time, such

as in the winter, the spa or pool set should be disassembled and stored indoors.

Caution: Read the instructions before using the appliance and every time you install or reassemble the appliance.

Keep the instructions safe. If the instruction is missing, please contact the manufacturer or download a copy from www.bestwaycorp.com

Warning: For electric safety, a PRCD is incorporated in the power cord. If current leakage of more than 10mA is detected, the device will operate and cut off the power supply. In such a case, please unplug and stop using the spa at once. Dont reset the product by yourself. You must contact the local service agent to check and repair the product.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (For market other than EU)

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. (For EU market)

Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock;

Water attracts children; always attach a spa cover after each use.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children can not use this spa unless they are supervised at all times.

RISK OF INJURY. Never operate spa if inlet / outlet pipes are broken or missing. Never attempt to replace the inlet / outlet pipes. Always consult your local Aftersales Centre.

RISK OF ELECTRIC SHOCK. Install at least 2m from all metal surfaces.

RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2m of spa.

During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.

TO REDUCE THE RISK OF INJURY: A. The water in a spa should never exceed 40C (104F).

Water temperature between 38C (100F) and 40C (104F) is considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

B. Since excessive water temperatures have a high potential for causing fetal damage during the early months of

pregnancy, pregnant or possibly pregnant women should limit spa water temperature to 38C (100F).

C. Before entering a spa, the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating device varies.

D. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.

E. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.

F. Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

TO REDUCE THE RISK OF INJURY: Never pour water with a temperature higher than 40C (104F) directly into the spa pool.

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level that is several degrees above the normal body temperature of 37C (98.6F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.

Electric installations should follow national wiring rules, consult a qualified electrician with any questions.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS. CAUTION:

The spa should not be setup or left out in temperature lower than 4C (40F).

Do not use the spa alone. People with infectious diseases should not use a spa. Do not use the spa immediately following strenuous

exercise. Always enter and exit the spa slowly and cautiously. Wet

surfaces are slippery. To avoid damage to the pump, the spa must never be

operated unless the spa is filled with water. Immediately leave spa if the user feels uncomfortable or

sleepy. Never add water to chemicals. Always add chemicals to

water to avoid strong fumes or violent reactions that may result in hazardous chemical spray.

Regarding the information pertaining to cleaning, maintenance of water, and disposal of water, please see section «MAINTENANCE».

Regarding the information pertaining to the installation, thanks to refer to the below paragraph of the manual.

NOTE: Please examine equipment before use. Notify Bestway at

the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.

This product is not intended for commercial use.

WARNING FOR ELECTRIC AIR PUMP (For Palm Springs HydroJet): The electric air pump is not a part of spa. You should refer to the user manual of electric air pump for safety. Extension cord used for the air pump when inflating the pool is strictly forbidden to be used for the spa. After inflation of the pool, the air pump, as well as extension cord must be disconnected from supply mains and stored indoor place. Motor run time should not exceed 20 minute CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO WATER OR RAIN. FOR HOUSEHOLD USE ONLY.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic

safety precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS — READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: The spa must be supplied through an isolating transformer

or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.

The pump must be tested before each use. To test, follow the instructions in the Pump Test section of this manual.

If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.

To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.

No part of the appliance is to be located above the bath during use.

Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to a person in spa pool; Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa pool.

The plug of pump shall be more than 3.5m away from the spa.

It is necessary to have the plug accessible after installation of the spa.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on and off by the utility.

After using your spa for 3-5 years, you should contact your local qualified maintenance technician to ensure the safety and performance of the spa. The main components, such as heating element, air blower motor and non-return valves within the electric unit should be checked and replaced(if necessary) by professional persons.

Warning: Always keep plug dry, plug in with wet plug is definitely forbidden!

The plug shall be directly connected only to a socket-outlet of the fixed electrical installation.

The spa must be supplied by earthed power source. TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA

WHEN IT IS RAINING. Never wear your contact lenses when in your spa. Do not use spa during chemical maintenance. Extension cords cannot be used. Dont plug or unplug the appliance if your hands are wet. Always unplug the appliance: — on rainy days — before cleaning or other maintenance — if you leave it unattended on holidays When the appliance will be not used for a long time, such

as in the winter, the spa or pool set should be disassembled and stored indoors.

Caution: Read the instructions before using the appliance and every time you install or reassemble the appliance.

Keep the instructions safe. If the instruction is missing, please contact the manufacturer or download a copy from www.bestwaycorp.com

Warning: For electric safety, a PRCD is incorporated in the power cord. If current leakage of more than 10mA is detected, the device will operate and cut off the power supply. In such a case, please unplug and stop using the spa at once. Dont reset the product by yourself. You must contact the local service agent to check and repair the product.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

5

they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (For market other than EU)

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. (For EU market)

Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock;

Water attracts children; always attach a spa cover after each use.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children can not use this spa unless they are supervised at all times.

RISK OF INJURY. Never operate spa if inlet / outlet pipes are broken or missing. Never attempt to replace the inlet / outlet pipes. Always consult your local Aftersales Centre.

RISK OF ELECTRIC SHOCK. Install at least 2m from all metal surfaces.

RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2m of spa.

During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.

TO REDUCE THE RISK OF INJURY: A. The water in a spa should never exceed 40C (104F).

Water temperature between 38C (100F) and 40C (104F) is considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

B. Since excessive water temperatures have a high potential for causing fetal damage during the early months of

pregnancy, pregnant or possibly pregnant women should limit spa water temperature to 38C (100F).

C. Before entering a spa, the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating device varies.

D. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.

E. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.

F. Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

TO REDUCE THE RISK OF INJURY: Never pour water with a temperature higher than 40C (104F) directly into the spa pool.

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level that is several degrees above the normal body temperature of 37C (98.6F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.

Electric installations should follow national wiring rules, consult a qualified electrician with any questions.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS. CAUTION:

The spa should not be setup or left out in temperature lower than 4C (40F).

Do not use the spa alone. People with infectious diseases should not use a spa. Do not use the spa immediately following strenuous

exercise. Always enter and exit the spa slowly and cautiously. Wet

surfaces are slippery. To avoid damage to the pump, the spa must never be

operated unless the spa is filled with water. Immediately leave spa if the user feels uncomfortable or

sleepy. Never add water to chemicals. Always add chemicals to

water to avoid strong fumes or violent reactions that may result in hazardous chemical spray.

Regarding the information pertaining to cleaning, maintenance of water, and disposal of water, please see section «MAINTENANCE».

Regarding the information pertaining to the installation, thanks to refer to the below paragraph of the manual.

NOTE: Please examine equipment before use. Notify Bestway at

the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.

This product is not intended for commercial use.

WARNING FOR ELECTRIC AIR PUMP (For Palm Springs HydroJet): The electric air pump is not a part of spa. You should refer to the user manual of electric air pump for safety. Extension cord used for the air pump when inflating the pool is strictly forbidden to be used for the spa. After inflation of the pool, the air pump, as well as extension cord must be disconnected from supply mains and stored indoor place. Motor run time should not exceed 20 minute CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO WATER OR RAIN. FOR HOUSEHOLD USE ONLY.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic

safety precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS — READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: The spa must be supplied through an isolating transformer

or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.

The pump must be tested before each use. To test, follow the instructions in the Pump Test section of this manual.

If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.

To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.

No part of the appliance is to be located above the bath during use.

Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to a person in spa pool; Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa pool.

The plug of pump shall be more than 3.5m away from the spa.

It is necessary to have the plug accessible after installation of the spa.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on and off by the utility.

After using your spa for 3-5 years, you should contact your local qualified maintenance technician to ensure the safety and performance of the spa. The main components, such as heating element, air blower motor and non-return valves within the electric unit should be checked and replaced(if necessary) by professional persons.

Warning: Always keep plug dry, plug in with wet plug is definitely forbidden!

The plug shall be directly connected only to a socket-outlet of the fixed electrical installation.

The spa must be supplied by earthed power source. TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA

WHEN IT IS RAINING. Never wear your contact lenses when in your spa. Do not use spa during chemical maintenance. Extension cords cannot be used. Dont plug or unplug the appliance if your hands are wet. Always unplug the appliance: — on rainy days — before cleaning or other maintenance — if you leave it unattended on holidays When the appliance will be not used for a long time, such

as in the winter, the spa or pool set should be disassembled and stored indoors.

Caution: Read the instructions before using the appliance and every time you install or reassemble the appliance.

Keep the instructions safe. If the instruction is missing, please contact the manufacturer or download a copy from www.bestwaycorp.com

Warning: For electric safety, a PRCD is incorporated in the power cord. If current leakage of more than 10mA is detected, the device will operate and cut off the power supply. In such a case, please unplug and stop using the spa at once. Dont reset the product by yourself. You must contact the local service agent to check and repair the product.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (For market other than EU)

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. (For EU market)

Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock;

Water attracts children; always attach a spa cover after each use.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children can not use this spa unless they are supervised at all times.

RISK OF INJURY. Never operate spa if inlet / outlet pipes are broken or missing. Never attempt to replace the inlet / outlet pipes. Always consult your local Aftersales Centre.

RISK OF ELECTRIC SHOCK. Install at least 2m from all metal surfaces.

RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2m of spa.

During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.

TO REDUCE THE RISK OF INJURY: A. The water in a spa should never exceed 40C (104F).

Water temperature between 38C (100F) and 40C (104F) is considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

B. Since excessive water temperatures have a high potential for causing fetal damage during the early months of

6

pregnancy, pregnant or possibly pregnant women should limit spa water temperature to 38C (100F).

C. Before entering a spa, the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating device varies.

D. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.

E. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.

F. Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

TO REDUCE THE RISK OF INJURY: Never pour water with a temperature higher than 40C (104F) directly into the spa pool.

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level that is several degrees above the normal body temperature of 37C (98.6F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.

Electric installations should follow national wiring rules, consult a qualified electrician with any questions.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS. CAUTION:

The spa should not be setup or left out in temperature lower than 4C (40F).

Do not use the spa alone. People with infectious diseases should not use a spa. Do not use the spa immediately following strenuous

exercise. Always enter and exit the spa slowly and cautiously. Wet

surfaces are slippery. To avoid damage to the pump, the spa must never be

operated unless the spa is filled with water. Immediately leave spa if the user feels uncomfortable or

sleepy. Never add water to chemicals. Always add chemicals to

water to avoid strong fumes or violent reactions that may result in hazardous chemical spray.

Regarding the information pertaining to cleaning, maintenance of water, and disposal of water, please see section «MAINTENANCE».

Regarding the information pertaining to the installation, thanks to refer to the below paragraph of the manual.

NOTE: Please examine equipment before use. Notify Bestway at

the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.

This product is not intended for commercial use.

WARNING FOR ELECTRIC AIR PUMP (For Palm Springs HydroJet): The electric air pump is not a part of spa. You should refer to the user manual of electric air pump for safety. Extension cord used for the air pump when inflating the pool is strictly forbidden to be used for the spa. After inflation of the pool, the air pump, as well as extension cord must be disconnected from supply mains and stored indoor place. Motor run time should not exceed 20 minute CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO WATER OR RAIN. FOR HOUSEHOLD USE ONLY.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic

safety precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS — READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: The spa must be supplied through an isolating transformer

or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.

The pump must be tested before each use. To test, follow the instructions in the Pump Test section of this manual.

If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.

To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.

No part of the appliance is to be located above the bath during use.

Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to a person in spa pool; Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa pool.

The plug of pump shall be more than 3.5m away from the spa.

It is necessary to have the plug accessible after installation of the spa.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on and off by the utility.

After using your spa for 3-5 years, you should contact your local qualified maintenance technician to ensure the safety and performance of the spa. The main components, such as heating element, air blower motor and non-return valves within the electric unit should be checked and replaced(if necessary) by professional persons.

Warning: Always keep plug dry, plug in with wet plug is definitely forbidden!

The plug shall be directly connected only to a socket-outlet of the fixed electrical installation.

The spa must be supplied by earthed power source. TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA

WHEN IT IS RAINING. Never wear your contact lenses when in your spa. Do not use spa during chemical maintenance. Extension cords cannot be used. Dont plug or unplug the appliance if your hands are wet. Always unplug the appliance: — on rainy days — before cleaning or other maintenance — if you leave it unattended on holidays When the appliance will be not used for a long time, such

as in the winter, the spa or pool set should be disassembled and stored indoors.

Caution: Read the instructions before using the appliance and every time you install or reassemble the appliance.

Keep the instructions safe. If the instruction is missing, please contact the manufacturer or download a copy from www.bestwaycorp.com

Warning: For electric safety, a PRCD is incorporated in the power cord. If current leakage of more than 10mA is detected, the device will operate and cut off the power supply. In such a case, please unplug and stop using the spa at once. Dont reset the product by yourself. You must contact the local service agent to check and repair the product.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (For market other than EU)

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. (For EU market)

Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock;

Water attracts children; always attach a spa cover after each use.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children can not use this spa unless they are supervised at all times.

RISK OF INJURY. Never operate spa if inlet / outlet pipes are broken or missing. Never attempt to replace the inlet / outlet pipes. Always consult your local Aftersales Centre.

RISK OF ELECTRIC SHOCK. Install at least 2m from all metal surfaces.

RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2m of spa.

During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.

TO REDUCE THE RISK OF INJURY: A. The water in a spa should never exceed 40C (104F).

Water temperature between 38C (100F) and 40C (104F) is considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

B. Since excessive water temperatures have a high potential for causing fetal damage during the early months of

pregnancy, pregnant or possibly pregnant women should limit spa water temperature to 38C (100F).

C. Before entering a spa, the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating device varies.

D. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.

E. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.

F. Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

TO REDUCE THE RISK OF INJURY: Never pour water with a temperature higher than 40C (104F) directly into the spa pool.

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level that is several degrees above the normal body temperature of 37C (98.6F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.

Electric installations should follow national wiring rules, consult a qualified electrician with any questions.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS. CAUTION:

The spa should not be setup or left out in temperature lower than 4C (40F).

Do not use the spa alone. People with infectious diseases should not use a spa. Do not use the spa immediately following strenuous

7

exercise. Always enter and exit the spa slowly and cautiously. Wet

surfaces are slippery. To avoid damage to the pump, the spa must never be

operated unless the spa is filled with water. Immediately leave spa if the user feels uncomfortable or

sleepy. Never add water to chemicals. Always add chemicals to

water to avoid strong fumes or violent reactions that may result in hazardous chemical spray.

Regarding the information pertaining to cleaning, maintenance of water, and disposal of water, please see section «MAINTENANCE».

Regarding the information pertaining to the installation, thanks to refer to the below paragraph of the manual.

NOTE: Please examine equipment before use. Notify Bestway at

the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.

This product is not intended for commercial use.

WARNING FOR ELECTRIC AIR PUMP (For Palm Springs HydroJet): The electric air pump is not a part of spa. You should refer to the user manual of electric air pump for safety. Extension cord used for the air pump when inflating the pool is strictly forbidden to be used for the spa. After inflation of the pool, the air pump, as well as extension cord must be disconnected from supply mains and stored indoor place. Motor run time should not exceed 20 minute CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO WATER OR RAIN. FOR HOUSEHOLD USE ONLY.

SAVE THESE INSTRUCTIONS

IMPORTANT ! To reach 40C (104F), the heating duration required is base on the starting water temperature and ambient temperature, the data below is purely for reference. To display the current water temperature, run the filter system for at least a minute.

8

Ambient Temperature

10C(50F)

15C(59F)

20C(68F)

25C(77F)

30C(86F)

Water Temperature

10C(50F)

15C(59F)

20C(68F)

25C(77F)

30C(86F)

Set Temperature

40C(104F)

40C(104F)

40C(104F)

40C(104F)

40C(104F)

Heating Duration

18.5h-21.5h

15h-18h

11.5h-14.5h

8.5h-11h

5.5h-7.5h

Be sure to cover the spa with the spa cover whenever the heating function is activated. Leaving the spa uncovered will increase the heating duration required. Please do not use the spa when ambient temperature is lower than 4C (39F ).

HYDROJET

220-240V AC,2060W

2,000W at 20C

50W

—

1200W

10W

SPECIFICATION

Power Rate

Heat Element Power

Filter Pump Power

Massage Tube Power

Jet Pump Power

Soft Water System

HYDROJET PRO

220-240V AC,2060W

2,000W at 20C

50W

800W

1200W

10W

9

WARNING: The selected location has to be able to support of supporting the expected load. WARNING: An adequate drainage system has to be provided to deal with overflow water for both indoor and outdoor installations. NOTE: Only the Hydro-Jet Pro spa has the Lay-Z-Massage system button. When inflating, you will notice that air will be expelled from the area where the air hose connects to the pump, this is normal and prevents damage due to over-inflation. NOTE: Do not use an air compressor to inflate the pool. NOTE: Do not drag the pool on rough ground as this may cause

ASSEMBLY

SPA PUMP EQUIPOTENTIAL BONDING TERMINAL It is recommended to arrange for a qualified electrician to connect the spa pump to an equipotential bonding terminal using a minimum 2.5mm2 solid copper conductor.

Pump Test

NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale. 1. Insert the plug. 2. Press the RESET button, the indicator light turns on. 3. Press the TEST button, the indicator light turns off. 4. Press the RESET button, the indicator light turns on. 5. Press the On/Off button for 2 seconds, your pump is ready to use.

WARNING: The PRCD plug must be tested before each use to avoid risk of electric shock. WARNING: Before inserting plug into a power outlet, make sure the current rate of the power outlet is suitable for the pump. WARNING: Do not use the pump if this test fails and contact our Customer Service.

PRCD Test

RESET

TEST

2

RESET

TEST

4

RESET

TEST

1 3

RESET

TEST

Please refer to the provided Instructional page

OPERATION

Air Valve Check Always check the air valve carefully before inflation to ensure there is not an air leak. If the air valve is loose, use the provided wrench to fasten the air valve following these steps: With one hand, hold the backside of the air valve from the inner side of the spa wall and turn the wrench clockwise. NOTE: 1. Do not over tighten. 2. Do not adjust the air valve connector when the spa is in use.

10

2. 90

1.

damage to the pool liner. NOTE: Inflation time is for reference only. NOTE: Pressure gauge is for inflation purpose only, and the value shown by the pressure gauge is just for reference. It should not be used as a precision instrument.

Water Filter Button

HydroJet System Button This button turns the water pump on and off. The light above the HydroJet system button displays red when activated.

Heat Button

Power-Saving Timer Button

HYDROJET PRO HYDROJET

Note: The system will shut off automatically after 1 hour. Note: Do not dry run the HydroJet System.

NOTE: If the heating system is activated, the filtration system will automatically start. NOTE: After turning off the heating system, the filtration system will continue to operate.

NOTE: The built-in hard water treatment function works automatically.

This is a newly added function, designed to help avoid wasting power by setting the time and duration of the heating cycle for the spa. This way, you can enjoy your spa at the time you desire, without needing to leave the heater on at all times.

STEP 1: Set the heating duration 1. Press the button unit the LED starts to flash. 2. Press the or button to adjust the heating duration (From 1-48 hours). 3. Press the button again to confirm the heating duration. STEP 2: Set the number of hours FROM NOW when the heater will activate 1. After setting the heating duration, the LED starts to flash. 2. Press the or button to adjust the hours until time of activation (From 0-99 hours). 3. Press button again or simply touch nothing for 10 seconds to confirm the setting.The LED will light steadily, and the countdown to heater activation will begin. To modify the timer settings: Press the button and use the or button to adjust. Cancel the setting: Press the button for 2 seconds.

Lay-Z-Massage System Button (For Hydro-Jet Pro)

IMPORTANT: Do not run the Lay-Z-Massage system when the cover is attached. Air can accumulate inside the spa and cause irreparable damage to the cover and bodily harm. NOTE: Heat and massage system work together to create a warm massage experience.

Use this button to activate the heating system. When the light above the heat button is red, the heating system is activated. When the light is green, the water is at the set temperature and the heating system is at rest.

This button turns the filter pump on and off. The light above the Water Filter Button displays red when activated.

Temperature Adjustment Buttons

Celsius/Fahrenheit Toggle

Press this button for 2 seconds to active the control panel bottons and the light turns to green. Press this button for 2 seconds to turn off all currently activated functions.

On/Off Button

Power-Saving Timer LED

Once powered up, the LED displays the current water temperature automatically. After 72 hours of filtration (without using the power saving timer function), the pump will hibernate and flash End with the current water temperature. When the pump is hibernating both the heating and water filter functions are disabled. To re-active the pump press lock/unlock button for 3 seconds.

LED Display

NOTE: The water heat rate may change in the below conditions: When the outdoor temperature is below 15C (59F). If the cover is not in position when the heating function is activated. NOTE: To display the current water temperature, run the filter system for at least a minute. The water temperature as tested by an external thermometer may vary from the temperature as displayed on the spa panel due to the differing positions of the measurement devices.

This LED flashing means you are setting the heating duration. The light will be on when the heating function starts to work. This LED flashing means you are setting the number of hours FROM NOW when the heater will activate. When the light is on, the Power-Saving Timer function is set.

The temperature can be displayed in either Celsius or Fahrenheit.

Pressing the Temperature Increase or Decrease buttons will cause the LED to flash. When it is flashing you can adjust to the desired temperature setting. If you hold these buttons down, the values will rapidly increase or decrease. The new and desired temperature setting will remain on the LED display for 3 seconds to confirm the new value.

NOTE: The default temperature is 35C (95F). NOTE: Temperature adjustment ranges from 20C (68F) to 40C (104F).

NOTE: After setting, the screen flashes the current temperature and time alternately.

The pump has a 5-minute auto-lock. The LED light will dim out when the pump is locked (no function is activated).To lock or unlock the pump, place a finger over the lock/unlock button for 3 seconds.

Use this button to activate the massage system, which has a 30-minute auto-shutoff feature. The light above the Lay-Z-Massage system button displays red when activated.

Lock/Unlock Button

NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 48 hours; Reservation time adjustment (the number of hours FROM NOW when the heater will begin to function) may be set from 0 to 99 hours. If the timer is set at 0 hour, it means the Timer function is not set. Note that the timer is one time per use — the user sets the duration of the heating cycle, and how many hours from now the heating cycle begins. The timer does NOT repeat until reset.

11

+

—

4. Heating Reset

When using the Lay-Z-Spa for the first time, or after a long period of inactivity, be sure to press the reset button on the pump using a small and thin object.

If the temperature on the control panel (or the water temperature) has not changed 4-5 hours after activation of the heating system, use a thin object to press the RESET BUTTON and restart the heating system. IMPORTANT: The heating System will not operate if the outside temperature is above 40C (104F) or if the Lay-Z-Spa is under direct sunlight. Under these conditions, please wait until a cooler time of day before pressing the RESET BUTTON with a thin object and restart the heating System. This operation must be repeat everytime when the pump is under above conditions.

RESET BUTTON IMPORTANT INSTRUCTIONS FOR USE

RESET

3. Adjustment of Jet Nozzle

Item code

54138

54144

54173

Maldives Hydrojet Pro

Hawaii Hydrojet Pro

Plam Springs Hydrojet

130 130

146

151 151

Description Inner diameter (cm)

Filter Cartridge Maintenance NOTE: To ensure your spa water stays clean, check and clean your filter cartridges every day-follow the steps below.

NOTE: We recommend changing your filter cartridges every week. If the filter cartridges remain soiled and discolored they should be replaced. Water Maintenance To keep your SPA water clean, chemical balance is necessary. Merely cleaning the filter cartridge is not sufficient for this purpose. Please refer to either of below recommendations:

Filter Set Filter Cartridge 58323

12

MAINTENANCE NOTE: Your spa will require additional air to be added from time to time. Changes in temperature from day to night will change the pressure in the spa and may cause a certain amount of deflation. Please follow the Assembly instructions and drain the spa before inflating to the accurate pressure needed. CAUTION: YOU MUST ENSURE THE PUMP IS UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE.

1. The water flow sensor flags didnt fall back into the correct position.

2. The water flow sensors are broken.

1. You forgot to remove the 2 stopper caps from inside the pool.

2. The filter cartridges are dirty. 3. Activate the filter or heat system and put your hand

in front of the outlet pipe inside the pool to check if you can feel water. flowing out.

a. If no water flows out the water pump is broken. b. Water flows out but the alarm appears, the

water flow sensors are broken.

1. The water temperature is lower than 4C (40F). 2. If the water temperature is higher than

7C (44.6F), the pumps thermometer is broken.

1. The water temperature is over 50C (122F). 2. If the water temperature is lower than

45C (113F), the pumps thermometer is broken.

1. The pumps thermometer connectors are not working properly.

2. The pumps thermometer is broken.

The manual reset thermal cut-out has been tripped.

The fuse is disconnected.

1. Unplug the pump, strike the side of the pump firmly (but not violently), and plug it back in.

2. Contact your local Bestway Aftersales Service Center for instructions.

1. Remove the two stopper caps before starting the heating system. Refer to the Assembly section in the Users Manual.

2. Remove the filter set from inside the pool and push the filter or heat button. If no alarm appears, clean or change the filter cartridges and re-install the filter set inside the pool.

3. Contact your local Bestway Aftersales Service Center for instructions.

1. The spa is not designed to operate with water temperatures lower than 4C (40F). Unplug the pump and only re-start the pump when the water temperature reaches 6C (43F).

2. Contact your local Bestway Aftersales Service Center for instructions.

1. The spa is not designed to operate with water temperatures greater than 40C (104F). Unplug the pump and only re-start the pump when the water temperature reaches 38C (100F) or lower. IMPORTANT: Before you re-start the pump, push the pumps reset button.

2. Contact your local Bestway Aftersales Service Center for instructions.

Contact your local Bestway Aftersales Service Center for instructions.

Contact your local Bestway Aftersales Service Center for instructions.

1. Unplug the pump and push the reset button, then plug the pump back in. 2. In case the alarm still remains, check the RESET BUTTON section in manual. 3. Contact your local Bestway Aftersales Service Center for instructions.

Contact your local Bestway Aftersales Service Center for instructions.

SolutionsCauses Reasons The water flow sensors work without pressing the filter or heat button.

After starting or during the functions of filtering or/and heating, the water flow sensors do not detect water flow.

The pumps thermometer reads the water temperature below 4C (40F).

The pumps thermometer reads the water temperature over 50C (122F).

The pumps thermometer connections have issues.

The manual reset thermal cut-out has a problem.

104C (219F) Fuse fault.

Alarms

The system has detected some water leakage inside the pump.

Water leakage inside the pump.

Contact your local Bestway Aftersales Service Center for instructions.

Contact your local Bestway Aftersales Service Center for instructions.

The signal line between control panel and power board is not well connected.

1. The ground bonding of your home has some problem. 2. The pump has some problem.

Signal line disconnected.

Ground Connection Failed

Water quality will be directly related to frequency of use, number of users and overall maintenance of the spa. The water should be changed every 3 days if there is no chemical treatment being performed with the water. NOTE: We recommend you take a shower before using your Lay-Z-Spa. Cosmetic products, lotions, and other residues on the skin can quickly degrade water quality. NOTE: Remove the chemical dispenser from the spa when the spa is in use IMPORTANT: After performing chemical maintenance and before using the spa, use a test kit (not included) to test the water chemistry. We recommend maintaining your water as per the table below.

NOTE: Damage resulting from chemical imbalance is not covered by the warranty. Pool chemicals are potentially toxic and should be handled with care. There are serious health risks from chemical vapors and the incorrect labeling and storage of chemical containers. Please consult your local pool supply retailer for more information about chemical maintenance. Pay close attention to the chemical manufacturer’s instructions. Spa damage resulting from misuse of chemicals and mismanagement of spa water is not covered by the warranty.

13

pH 7.4-7.6

Total Alkalinity 80-120ppm

Free Chlorine 2-4ppm

Using chemical liquid (not included) (Refer to the instructions of the liquid chemicals purchased)

Using chemical tablets (not included)

Jet Nozzle Maintenance 1. Twist untill hearing a click sound, and

pull out the Jet Nozzle to clean the debris. 2. Insert and twist clockwise to put it back.

14

Draining the Spa NOTE: Drawings for illustration purposes only. May not reflect actual product. Not to scale.

Spa Repair For Spa inflatable cover If the spa is torn or punctured, use the provided heavy-duty repair patch. 1. Clean area to be repaired. 2. Carefully peel patch. 3. Press patch over area to be repaired. 4. Wait 30 minutes before inflation.

For Spa Liner If the spa is torn or punctured, use the provided PVC repair patch and glue (not included) following these steps: 1. Clean and dry the area to be repaired. 2. Cut the provided PVC patch to appropriate size. 3. Use glue (not included) to coat the one side of the newly cut patch. Make sure the glue is

evenly distributed. 4. Wait for 30 seconds and then place the cut patch with glue over the damaged area. 5. Smooth out any bubbles of air that may be trapped underneath, and press firmly for two

minutes. 6. Wait 30 minutes before inflation. 7. The product is once again ready for use. Repeat this process should further leaks occur.

NOTE: DO NOT use hard brushes or abrasive cleaners.

Detergent residues and dissolved solids from bathing suits and chemicals may build up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.

Cleaning the spa

DEFLATION

2. 3. 4. 5.1.

P6611

Only for Hydro-Jet Pro

P6H565

P61813

6. 7. 8. 9.

NOTE: Lift up the spa when there is only a little water left. Damages to the handles are not covered under the warranty.

NOTE: Twist and pull out the Jet Nozzle, and turn the spa upside down to dry the water pipe.

10. 11. 12.NOTE: Dry the SPA pool (only for Hydro-Jet Pro)

Only for Hydro-Jet Pro 13. NOTE: Dry the SPA pump (only for Hydro-Jet Pro)

2.

P61726 P61725 P61727

P61726

P61725HYDROJET PRO

HYDROJET

P61725

Cover

2

15

Problems Pump does not operate

Pump does not heat properly

Lay-Z-Massage System does not work

Pump adapters are not level with the spa adapters

Spa pool leakage

Water is not clean

Probable Causes

— Spa is torn or punctured — Air valve is loose

Solutions — Check power source — Contact your local Bestway Aftersales Service Center for instructions

— Elevate the pump with wood or another type of insulated material to bring the pump’s adapters level with the spa’s adapters

— Power failure — Power circuits broken

— Temperature set too low — Dirty filter cartridge — The thermal cut-out cuts off — The heating element has failed

— Air Pump is overheating — The massage system stops automatically — Air pump is broken

— One characteristic of PVC is that it changes shape, which is normal

— Insufficient filtering time — Dirty Filter Cartridge — Improper water maintenance

— Set the heating system to a higher temperature (refer to Pump Operation section) — Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning and Replacement section) — Re-start when the temperature is below 38C (100F) — Contact your local Bestway Aftersales Service Center for

instructions

— Unplug the pump and wait two hours until the pump has cooled. Insert the plug and press the massage system button

— Press the massage system button to reactivate — Contact your local Bestway Aftersales Service Center for

instructions

— Increase filtration time — Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning

and Replacement section) — Refer to the chemical manufacturers instructions

— Use provided repair patch — Using soapy water, cover the air-valve to check if air is leaking, if

so, use the provided wrench to fasten the air-valve following these steps:

1. Deflate the SPA. 2. With one hand, hold the backside of the air valve from the inner side of the spa wall and turn the wrench clockwise.

Control panel not working

What kind of chemicals should be used for water maintenance?

Please consult your local chemical supplier for information about chemical maintenance. Pay close attention to the chemical manufacturers instructions.

Water leaks from the adapters between the pump and spa

Insert the three stopper caps on to the spas ports to prevent water from escaping and disconnect the pump. Check and make sure the seals are placed correctly inside the pump adapters. If the seals are missing or not installed correctly, please contact your local Bestway Aftersales Service Center for instructions. If the seals are correctly in place, reconnect the pump to the spa and hand-tighten the adapters.

— The control panel has an auto-lock, which is activated after 5 minutes of inactivity. The LED display has one icon: If the lock icon is highlighted, the control panel is locked.

— Control panel is not activated.

— To unlock the control panel, press the button for 3 seconds. If the control panel will not unlock, restart the pump unplug and plug in the pump. — Press the on/off button for 2 seconds

If the problem persists, please contact your local Bestway Aftersales Service Center for instructions.

There is a defect in your spa Contact your local Bestway Aftersales Service Center and return the SPA.

PRCD test failed

HydroJet System does not work — Unplug the pump and wait for two hours until the pump has cooled. Plug in and try again — Contact your local Bestway Aftersales Service Center for instructions

— Water pump is overheating — Water pump is broken

TROUBLESHOOTING Bestway strives to provide the most trouble-free spas on the market. If you experience any problems whatsoever, do not hesitate to contact Bestway or your authorized dealer. Here are some helpful tips to help you to diagnose and rectify some common sources of trouble.

Lay-Z-Spa Storage Before storing, make sure the spa and pump are completely dry. This is essential to extend the life of the spa. We recommend using the pump to blow dry the spa, pump and pipes. Remove the filter sets and discard the used filter cartridges. Re-attach the two stopper caps onto the spas inlet and outlet valves. It is recommended you store the spa in its original package in a warm dry place. NOTE: Plastic becomes brittle and susceptible to breaking when exposed to subzero temperatures. Freezing can severely damage the spa. Improper winterization of your spa can void your warranty. Disposal Meaning of crossed-out wheeled dustbin symbol: Do not dispose of electrical appliances

as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.

2018 Bestway Inflatables & Material Corp. All rights reserved/Tous droits rservs/Todos los derechos reservados/Alle Rechte vorbehalten/Tutti i diritti riservati Trademarks used in some countries under license to/ Marques utilises dans certains pays sous la licence de/ Marcas comerciales utilizadas en algunos pases bajo la licencia de/ Die Warenzeichen werden in einigen Lndern verwendet unter Lizenz der/ Marchi utilizzati in alcuni paesi concessi in licenza a Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China. Manufactured,distributed and represented in the European Union by/ Fabriqus, distribus et reprsents dans lUnion Europenne par/Fabricado, distribuido y representado en la Unin Europea por/ Hergestellt, vertrieben und in der Europischen Union vertreten von/Prodotto, distribuito e rappresentato nell’Unione Europea da Bestway (Europe) S.r.l., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy Distributed in North America by/Distribus en Amrique du Nord par/Distribuido en Norteamrica por Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America Tel:1-855-838-3888 (For U.S. and Canada) Distributed in Latin America by/Distribu en Amrique latine par/Distribuido en Latinoamrica por/Distribu