Morgana digifold инструкция на русском

Related Manuals for Morgana DigiFold Pro

DigiFold Pro

DOCUMENT

FOLDING MACHINE

OPERATORS MANUAL

Morgana Systems Limited

Telephone: ( 01908 ) 608888

United Kingdom

Facsimile: ( 01908 ) 692399

Website: www.morgana.co.uk

ISSUE 2

August 2010

174-025

INDEX

INTRODUCTION & SPECIFICATION

The Morgana DigiFold Pro

SAFETY Do’s & Don’ts

THE Digifold Pro

Labeled Photograph

THE SWITCH PANEL

Detailed diagram and description

Features on the switch panel

PAGE

OPERATING THE DigiFold Pro

Adjusting the Papergate

Setting the Suction Slot

Setting the Vacuum Bleed

Setting the Adjustable Side Lay

Setting the Back-Stop

Setting the Air Distribution

Setting the Air Separation Pressure

Setting the Positions of the Drive Wheels and Hubs

TOUCHSCREEN OPERATION

Touchscreen Layout

Paper Settings Page

Roller Gap Set & Tilt Mechanism Page

Crease Settings Pages

Creases in ‘Set By Fold’ mode

Creases in ‘Set By Position’ mode

Fold Settings Pages

Folds in ‘Set By Fold’ mode

Folds in ‘Set By Position-’ mode

Example of ‘Set By Position’ mode

Delivery Settings Page

Status Screen

Running the Job

Setting the machine to operate in manual sheet feed mode

Store Pages

Tools Menu

THE BLADE ASSEMBLY

Adjusting the blade pressure

4

5

7

8

9

37

11

11

11

12

10

10

11

11

14

15

17

20

21

29

30

31

32

35

23

24

26

27

Page 2

FOLDING

DigiFold Pro

INDEX

REPLACING CREASING BLADE SETS

Installing new blade sets

Spare Blades

PERFORATING

Equipment, Spares

Setting the machine

Recommended Position of the Drive Wheels and Hubs

REMOVING PAPER JAMS

PAGE 38

41

42

43

44

45

TROUBLE SHOOTING

Paper crease out of square

Crease Position Inaccuracy

Paper fold out of square

Paper Jamming

Machine will not start

Paper not feeding

Cracking of the printed material along the crease

Using the Correct Blade Set

ERROR SCREENS

01

Sheet did Not Arrive

02

03

04

05

Paper Crunch

Double Sheet Feed

Blade Not Home

Blade Busy

10

11

12

13

06

07

08

09

Blade Home Failure 1

Blade Home Failure 2

Flying Home Failure

Clip 1 NOT Clear

Clip 1 NOT Blocked

Clip 2 NOT Clear

Clip 2 NOT Blocked

Overlap

DISPATCH KIT

47

47

47

47

48

48

48

49

52

52

52

52

53

53

50

50

50

50

51

51

51

56

ACCESSORIES AND OPTIONS

RECOMMENDED SPARES

MACHINE CALIBRATION HISTORY SHEET

FUSE POSITIONS & RATINGS

PRODUCT RECYCLING AND DISPOSAL

57

58 — 59

60

61

62

SYSTEM

Page 3

INTRODUCTION

DigiFold Pro

INTRODUCTION AND SPECIFICATION

Digifold Pro

is a registered trade mark of Morgana systems Ltd. The unique patented creasing and folding system, makes it possible to fold most delicate stocks from 0.11mm, up to 0.4mm thick. The

DigiFold Pro

reduces the possibility of scratching, marking or cracking appearing on the substrate, as is often associated with conventional folding machine methods.

It is

IMPORTANT

to note that to prevent cracking, when using dry ink or toner based print engines, the material

must

be fully acclimatised for at least 48 hours before putting an image onto the paper.

IMPORTANT

the operating environment should be controlled to a temperature between

16° C and 27° C Maximum.

Specification

Feeding System ………………………………………… Bottom suction feed

Max. Sheet Size ………………………………………… 700mm x 385mm (27.5” x 15”) [900mm x

385mm (35.4” x 15”) with Optional extension table].

Min. Sheet Size …………………………………………. 210mm x 140mm (8.3” x 5.5”) (dependant on stiffness of paper and type of fold).

Max. Paper Thickness ……………………………..

0.40mm (varies according to hardness,

Min. Paper Thickness ………………………………… 0.11mm

type of fold, and substrate).

(varies according to hardness,

Max. No. Creases per Sheet…………………………9

Max. No. Folds per Sheet……………………………. 2

Max. No. Stored Programmes ………………………Unlimited

type of fold, and substrate).

Min. Repeat Crease Distance………………………..40mm (1.6”)

Min. Repeat Fold Distance …………………………..70

mm (2.75”) (depending on paper weight)

Min. Crease Distance from Leading Edge……….50mm (1.96”)

Min. Fold Distance from Leading Edge …………. 50mm (1.96”) (depending on paper weight)

Min. Crease Distance from Tail Edge……………..50mm (1.96”)

Min. Fold Distance from Tail Edge ……………….. 50mm (1.96”) (depending on paper weight)

Min. Fold Length ……………………………………….. 70mm (2.75”)

Speed per Hour (A4 in half)…………………………. 6000 sheets

Note: The production speed varies according to the material size and the fold type.

Dimensions ………………………………………………. L: 2020mm H: 1265mm W: 680mm

L: (79.5”) H: (49.8”) W: (26.8”)

Weight ……………………………………………………… 190Kgs (+50Kgs packing)

Power Requirement …………………………………… 1 phase 220 / 240v

*As part of our continued product improvement plan, specifications and information published in this manual are subject to change without notice.

All specifications are dependant on application, type of stock, temperature, RH and print engine used.

Specifications quoted were measured on uncoated and unprinted stock.

E & OE.

Page 4

FOLDING

DigiFold Pro

Safety Do’s & Don’ts

Safety Do’s & Don’ts

REGLES DE SECURITE : « A FAIRE » ET « A NE PAS FAIRE »

Do — read this operator manual fully before operating the machine.

Lire ce mode d’emploi avant d’utiliser la machine.

Do — operate with the designated AC current only. Use an exclusive outlet, as overloading may cause fire or an electric shock.

Respecter l’alimentation électrique indiquée. Brancher sur une prise séparée car une surcharge peut entraîner un incendie ou un choc électrique.

Do — install the power cord out of the way to avoid a tripping hazard.

Installer le cordon d’alimentation de manière à ne pas pouvoir trébucher par dessus.

Do — make sure that the mains inlet connector is always easily accessible.

Ménager un accès libre à la prise de courant.

Do not — install the machine in an unstable place such that it tilts or shakes.

Ne pas installer la machine sur une surface non plane, afin d’éviter qu’elle ne penche ou ne vibre.

Do not — unplug the plug or unplug the power cord from the outlet with a wet hand, this can cause an electric shock.

Ne pas installer la machine sur une surface non plane, afin d’éviter qu’elle ne penche ou ne vibre.

Do not — unscrew and remove any covers from the machine, as it can cause an electric shock or injury.

Ne démonter et enlever aucun carter de la machine, par crainte de décharge

électrique ou de blessure.

Do not — place receptacles containing liquids on any surface.

Ne pas placer de récipient contenant un liquide sur la machine.

Do not — adjust any part of the machine whilst rollers are running

N’effectuer aucun réglage pendant que les rouleaux fonctionnent.

Do not — operate the machine with loose or trailing clothing or loose hair.

Ne pas porter de vêtements flottants et rassembler les cheveux longs lors de l’utilisation de la machine.

Do not — under any circumstances adjust the paper gate when the machine is switched on.

En aucune circonstance, régler le séparateur de papier lorsque la machine est branchée.

SYSTEM

Page 5

Warning Labels

Do — be aware of any finger traps and rotating parts when operating the machine.

Attention au risque de se coincer les doigts, et aux pièces en mouvement lors du fonctionnement de la machine.

Do — read this operator manual fully before operating the machine.

Lire ce mode d’emploi avant d’utiliser la machine.

Do not — operate the machine with loose or trailing clothing.

Ne pas porter de vêtements flottants lors de l’utilisation de la machine

Do not — operate the machine with loose hair.

Rassembler les cheveux longs lors de l’utilisation de la machine.

Page 6

Do — be aware of any finger traps and rotating parts when operating the machine.

Attention au risque de se coincer les doigts, et aux pièces en mouvement lors du fonctionnement de la machine.

Do — be aware of sharp points and blades.

Attention aux éléments tranchants et aux couteaux.

Do — be aware of rotating rollers.

Attention aux rouleaux en fonctionnement

Do — be aware of low current anti-static shock.

Attention aux faibles chocs d’électricité statique

FOLDING

DigiFold Pro

DigiFold Pro

DOCUMENT FOLDING MACHINE

Key to photograph below

1 Delivery assembly

2 Vacuum bleed knob

3 Suction slot knob

4 Switch panel

5 Air distribution knob

6 Air Separation Knob

7 Adjustable side lay

8 Back stop

9 Fixed side lay

10 Fuses

11 Paper Gate

12 Top cover

13 Touchscreen

14 Optional Extension Table

1

12 11

6

13

7 9

8 5

3

2

SYSTEM

14

10

4

Page 7

The Switch Panel

The Switch Panel houses the Compressor switch, System switch, and an industry standard Emergency Stop switch which will stop all power going to the machine when activated.

THE SWITCH PANEL

Compressor Switch

Page 8

System Switch

Emergency Stop Switch

FOLDING

DigiFold Pro

The Switch Panel

Features on the Switch Panel

System switch

When activated the system switch will operate the motors in order to begin the creasing sequence.

Compressor switch

Allows the operator to switch off the compressor unit in order to utilise the machine to manually feed sheets.

SYSTEM

Page 9

Operating the DigiFold Pro

Adjusting the Paper Gate

Set the height of the Paper Gate to approximately two thicknesses of paper, by turning the disc j. An excessive gap is a most likely cause of double sheet feeding.

This setting is only intended as a guide, for instance, sheets with an upward curl will require this setting to be increased.

J

TWO THICKNESSES

OF PAPER

WARNING.

DO NOT ADJUST THE

PAPER GATE WHILE THE

MACHINE IS RUNNING OR

THE SUCTION DRUM MAY

BECOME DAMAGED.

Setting the Suction Slot

The suction slot is located inside the vacuum roller and can be adjusted by releasing and moving the suction knob horizontally in either direction to the required position.

For light stocks set the knob to the left and for heavier stocks set the knob to the right.

Roller Gap 3

Knob

Roller Gap 2

Knob

Air Seperation

Knob

Roller Gap 1

Knob

Page 10

Blade Tilt

Knob

Adjustable

Side Lay

Suction

Slot Knob

Vacuum

Bleed Knob

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Setting the Vacuum Bleed

Situated on the front of the feed table, the Vacuum Bleed Knob is used to allow more control of the suction on the vacuum drum.

When light weight paper is being fed through the machine turn the knob clockwise to reduce the possibility of marking, or damage to the leading edge of the paper.

Setting the Adjustable Side Lay

Place the paper stack on to the loading table and slide up to the fixed side lay and paper

Gate. Release the clamps located at each end of the side lay and slide up towards the paper stack as demonstrated in fig 10.1. Allow a gap of approximately 0.5mm (1/64 inch) between the paper and the side lay.

Setting the Back Stop

Position the backstop and slide up towards the paper stack allowing a gap (as specified in the above step).

Setting the Air Distribution

Depending on the length of the sheet to be creased, the air distribution knob can be rotated to various positions in order to supply air to different ports. Position 2 is recommended for most sheet sizes. However, a better result may be obtained by using the settings below or by experimentation.

Position 1 —

2 —

3 —

4 —

5 —

0 —

For sheets longer than A3 (17”) in order to supply air to the centre of the stack, ports 2, 3 and 4 open.

For A5 sheets or 8 inches long, ports 1 and 2 open.

For A4 sheets or 11 inches long, ports 1 and 3 open.

For A3 sheets or 17 inches long, ports 1 and 4 open.

For sheets longer than A3 (17”) in order to supply air to the ends of the stack, ports 1 and 5 open.

For sheets longer than A3 (17”) in order to supply air evenly along the stack, ports 1, 3 and 5 open.

Port 1 Port 5

Air Distribution

Knob Shown

Set To Posn. 1

Setting the Air Separation Pressure

To control the amount of air supplied to the ports, the air separation knob can be rotated clockwise to decrease the pressure or anti-clockwise to increase the pressure.

SYSTEM

Page 11

Operating the DigiFold Pro

Setting the positions of drive wheels and hubs

It is important that the drive wheels and drive hubs, on the roller shafts, are arranged across the width of the media being creased; this is done to ensure that the media is accurately driven and supported through the rollers. A suggested layout, below (see FIG 15.1). The suggested layout,

when perfing, when Folding

, is shown is different, and is shown on page 44 (see FIG 38.1).

The drive wheels and hubs are fixed to the rollers by grub screws.

FIG 15.1

Page 12

WHEEL & HUB ARRANGEMENT, (WHEN FOLDING)

FOLDING

DigiFold Pro

Operating the DigiFold Pro

BLANK

PAGE

SYSTEM

Page 13

Operating the DigiFold Pro

TOUCHSCREEN OPERATION

1. Turn the Emergency Stop button clockwise to switch the power on. After the system start up procedure the touch screen will be displayed as shown below.

IMPORTANT.

If you have not been trained to operate this machine, we strongly advise that you select the red cross icon.

We recommend that you either seek training or ask a trained operator to run the machine for you.

Select the green tick icon only if you have been trained to operate this machine.

If you have not been trained to operate this machine and you select the green tick icon,

Morgana Systems Ltd accept no responsibility for personal injury, damage to the machine or damage to materials being processed by the machine.

WARNING:-

Wait at least 10 seconds, after making any selection on the Touchscreen panel, before switching the machine OFF. Failure to do so could result in the data storage being corrupted, and the machine not operating.

The touch screen is laid out into 3 main areas as shown below:

Setting page

Status of machine & data entry area. Also used for quick links to setting pages.

Tabs to enable switching between setting pages — choose either Paper Settings, Gap settings, Crease Setting, Fold settings,

Delivery settings, Store and Tools.

Page 14

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Setting Pages.

Paper settings Page

Paper Type — As a guide choose as follows:

0 — approx 0.1 thk

1 — approx 0.2 thk

2 — approx 0.3 thk

3 — approx 0.3+ thk

See Page 25

Batch Button — Image is identical to that shown in the status area. On selection the status area is replaced with a calculator for inputting new values.

Batch sizes of 1 to

998 may be set.

Fold Selection — For quick setting of fold positions on standard size sheets.

Highlighted fold is type currently selected, other folds may be selected.

Currently selected fold is shown in the status area.

NOTE:-

Select the Ruler Icon to set Fold positions manually (’Set by Position’ mode).

Page Thickness — On selection of status area is replaced with a calculator for inputting new values

Range = 0.1 to 0.4mm

Increments of 0.01mm

Paper Length — On selection the status area is replaced with a calculator for inputting new values. Length range = 190mm — 900mm

Arrows may be selected to increase or decrease the page size in 0.1mm

increments

Paper size Selection.

Pre-set Paper sizes for quick insertion — Standard sizes for country origin would be shown.

Paper input

SYSTEM

Page 15

Operating the DigiFold Pro

Batch size Selection.

Paper Thickness Selection.

Pre-set Batch sizes for quick insertion.

Paper Thickness input

Pre-set Paper Thickness sizes for quick insertion.

Page 16

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Roller Gap Set & Tilt Mechanism Page.

To get to the roller gap setting page click the lower tab

Roller gaps may be in the range of 0.05mm to 1.5mm, with increments of 0.05mm

Current gap setting for 2nd Fold Roller

Current gap setting for 1st Fold Roller

Current gap setting for 3rd

Fold Roller

Recommended gap values based on paper thickness.

Current set Tilt Angle

Setting the Roller Gaps (Gap 1, Gap 2 & Gap 3)

The roller gaps can be adjusted to suit the thickness of the material being creased or folded; and the type of fold being produced. The roller gaps may also require adjustment if cracking of the print is noticeable. (see Fig 13.1 below).

FIG 13.1

K2

Roller Gap 3

Roller Gap 2

INFEED

K1

Roller Gap 1

SYSTEM

Page 17

Operating the DigiFold Pro

The gap settings (Gap 1, Gap 2 & Gap 3) can then be adjusted by rotating the Roller

Gap Set Knobs (see FIG 10.1 on page 10).

IMPORTANT.

When setting roller gaps, you

must

first adjust the gap to a value greater than that required and then decrease the value to the required setting. (Do not set the gap, from a value lower than that required).

PROCEDURE.

(i) Measure the thickness of the sheet using a Digital Vernier Calliper.

(ii) Set roller GAP 1 to the vernier reading.

(iii) Set roller GAP 2 and roller GAP 3, (for the type of fold being produced), using the

GAP SET GUIDE table shown below.

Half Fold on Knife 1

Half Fold on Knife 2

GAP SET GUIDE

FOLD TYPE GAP 3 GAP 2

Half K1

Half K2

Letter

Concertina

Gate

Closed Gate

Engineering

Double

3X

3X

3X

4X

2X

2X

3X

3X

X

2X

X

X

2X

X

X

X

GAP 1

X

X

X

X

X

X

X

X

Example 1:- When producing a

Half K1

fold, if GAP 1 is 0.2 (X) then set GAP 2 to 0.4

(2 x X) and set GAP 3 to 0.4 (2 x X).

Example 2:- When producing a

Gate

fold, if GAP 1 is 0.3 (X) then set GAP 2 to 0.3 (X) and set GAP 3 to 0.9 (3 x X).

FOLD TYPES

HALF

GATE

DOUBLE

LETTER

CLOSED GATE

CONCERTINA

ENGINEERING

Page 18

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Setting the Blade Tilt Mechanism

The blade tilt mechanism has been designed to compensate for when the creasing position on the sheet is not square. This could be due to an inaccuracy in the media or if the blade tilt mechanism has been incorrectly set. The mechanism will be set to zero

(square) when the machine is supplied. The Blade Tilt Mechanism can be adjusted if necessary by rotating the Blade Tilt Knob (see FIG10.1 on page 10).

SYSTEM

Page 19

Operating the DigiFold Pro

Crease Settings Pages.

To get to the crease setting page click the lower tab status area.

or from the

If you have selected a predefined standard Fold Type from the paper settings page the crease positions will be set for you. These positions can be fine tuned by

± 0.1mm

increments by pressing the arrow buttons for each crease.

Creases in ‘Set By Fold’ mode.

Crease trim — On selection the status area is replaced with a calculator for inputting new values.

Crease on/off selector green is on & red is off.

This is also indicated in the status area.

Trimming creases in ‘Set By Fold’ mode.

Creases may be trimmed by 0.1mm increments within the range of

5.0mm to +5.0mm.

Turn creasing off.

Greyed out area indicates the trim is not selectable

Page 20

Status shows creasing off icon

This button toggles creasing on & off.

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Creases in ‘Set By Position’ mode.

Arrows may be selected to increase or decrease

The page size in 0.1mm

increments

Crease position — On selection the status area is replaced with a calculator for inputting new values, a maximum of 9 creases can be added.

Number of creases — if more than 6 creases are added a scroll bar will appear for to enable viewing of all creases.

Also shown in status area.

Cross box for deletion of crease. On deletion of crease following creases will move up by one place. You will be asked to confirm deletion of the crease.

Press to remove all creases — you will be asked to confirm deletion.

Plus box for inserting additional creases. On selection following creases will move down by one place a maximum number of 6 creases can be seen at any one time further creases can be accessed by use of the scroll bar.

Additional creases added — scroll bar appears for more than six creases.

Trimming creases in ‘Set By Position’ mode.

Creases may be trimmed by 0.1mm increments within the range of

5.0mm to +5.0mm.

SYSTEM

Page 21

Operating the DigiFold Pro

Turn crease on/off.

Greyed out area indicates the trim is not selectable

Individual deletion of crease confirmation screen.

Status shows creasing off icon

This button toggles creasing on & off.

Crease 230 mm from lead edge will be deleted.

Remove all creases confirmation screen.

All creases — in this case 7 off will be deleted.

Page 22

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Fold Settings Pages.

To get to the Fold setting page click the lower tab status area.

or from the

If you have selected a predefined standard Fold Type from the paper settings page the crease positions will be set for you. These positions can be fine tuned by

± 0.1mm

increments by pressing the arrow buttons for each crease.

Folds in ‘Set By Fold’ mode.

K1 Fold trim — On selection the status area is replaced with a calculator for inputting new values.

Trim range is -5.0 to +5.0

with increments of 0.1mm

With Folding turned off the deflect positioned can be trimmed.

Trim range is -5.0 to +5.0

with increments of 0.1mm

SYSTEM

Folding can be trimmed for fine adjustments.

Trim range is -5.0 to +5.0

with increments of

0.1mm

Folding on/off selector green is on & red is off.

This is also indicated in the status area.

Page 23

Operating the DigiFold Pro

Folds in ‘Set By Position’ mode.

Fold distance from lead edge for knives (K1 & K2) increments of 0.1mm

K1 deflect button

K1 micro adjust selected

Clicking this icon switches deflect off &K1 returns to its original position.

K1 in deflect position.

This can be micro adjusted.

Trim range is -5.0 +5.0

with increments of 0.1mm

K1 & K2 in deflect position.

This can be micro adjusted.

Trim range is -5.0 +5.0

with increments of 0.1mm

Page 24

FOLDING

DigiFold Pro

Operating the DigiFold Pro

NOTES:-

If a crease position is adjusted, the fold will move with it.

If a fold position is adjusted, then only the fold will move.

Adjust a fold only if the fold appears to be giving an out of square result or cracking appears.

The fold is probably too close to the centre of the crease and will be trying to fold from one side of the crease to the opposite side of the crease (see below for explanation).

Paper Type — 0, 1, 2 and 3, is a fold compensation for variations in paper thickness, hardness and substrate.

l

Paper type

‘0’

— The crease and fold are set at exactly the same position. This may be used but beware some thin stocks will allow the fold to wander from one side of the crease to the other.

l

Paper type ‘1’ ‘2’

and

‘3’

will move the fold relative to the crease and should be tried out with the stock in use.

Generally a higher number will be best for a thicker stock, but some settings will swap the fold from one side to the other side of the crease, this enables the user to choose the side that the crease will be seen. For example, on a front cover.

.

SET BY POSITION

IMPORTANT NOTES.

1. If the fold is too near, or on the center line of the crease; the fold will try to fold diagonally across the crease profile and pull the fold out of square to the paper.

The best fold squareness is achieved when the fold is not on the center line of the crease, it should be to one side of the crease center line as shown below.

Thus for a crease setting of 100 for example, the fold should be set to a figure slightly smaller or greater than 100.

ideal fold line center line of crease ideal fold line

2. When using

Set By Position,

all dimensions are from the leading edge of the paper as shown in the example on page 26.

SYSTEM

Page 25

Operating the DigiFold Pro

Example of Set by Position.

Paper Length = 350mm (13.8”)

Feed Direction

Leading Edge

Crease 1

SETTINGS

Crease 1 = 97.0mm (3.8”)

Crease 2 = 179.0mm (7”)

Crease 3 = 260.0mm (10.2”)

Fold 1 = 179.0mm (7”)

Fold 2 = 260mm (10.2”)

Crease 2 Crease 3

Fold 1 Fold 2

All dimensions are from the leading edge of the paper

Crease 2

Fold 1

= 179.0

(7”)

Crease 3

Fold 2

= 260.0

(10.2”)

9mm

(0.35”)

Leading Edge

First Fold

Leading Edge

Second Fold

Page 26

9mm (0.35”)

Leading Edge

9mm (0.35”)

Finished Document

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Delivery Settings Page.

To get to the Delivery setting page click the lower

Roller position may be micro adjusted by clicking here.

Shingle may be micro adjusted by clicking here.

Roller adjustment calculator.

Shingle adjustment calculator.

The Delivery can be toggled On or Off by clicking here.

SYSTEM

Delivery on/off status red is off green is on.

Page 27

Operating the DigiFold Pro

Setting the Delivery Conveyor System.

WARNINGS:-

1. The Machine will not start if the delivery unit is not in its up position.

2. If the delivery is turned off the roller will feed to the far end of the belt conveyor and park there until turned on again.

3. If the delivery is turned on when using the ‘Set by Fold’ mode of operation; the Roller

Position and Shingle Length are automatically set, relative to the paper length and type of fold selected.

4. When using the ‘Set by Position’ mode of operation; the Roller Position and Shingle

Length must be adjusted manually to suit the job. (See FIG 17.1 below).

5. When the optimum settings for the roller position and shingle length are achieved they can be stored with the job.

NOTE.

When setting the machine to do a Double Fold or Engineering Fold, with a paper length of

279mm (11”) or less, the stacker roller will travel to the far end of the conveyor and stop.

This is due to the shortness of the folded paper exiting from the machine.

FIG 17.1

Page 28

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Status Screen.

Green icon indicates settings are saved — a red icon would show that settings have changed but the job has not been saved.

Paper length & Paper

Type — input from the paper setting screen.

Number of creases — this may alter automatically if a pre-defined fold is selected. Adjustments may be made in the crease setting screen.

Indicator for status of knives.

K1 & K2 On.

K1 Off & K2 On

K1 On & K2 Off

K1 & K2 Off

Clicking in this area will take you to the delivery setting page.

Clicking in this area will take you to the store page

Clicking in this area will take you to the paper setting page.

Currently selected fold type

— can be one of the following.

Clicking in this area will take you to the crease setting page.

Fold Positions & Trim settings

Clicking in this area will take you to the Fold setting page.

Batch quantity — this is input from the batch calculator on the paper setting screen — max. 999

Current job count — click to zero

A screen will appear to confirm that you want to reset the count.

Click to start machine with settings currently shown — you will receive a notification if system switch is not on. Press again to stop

Job

SYSTEM

Page 29

Run Job.

Operating the DigiFold Pro

Click to run machine.

System Switch Not On.

The machine running screen will appear.

Page 30

Click to confirm System switch is on & then click run button again

Run count

Batch Count

Job Count

Click to stop machine.

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Setting the machine to operate in manual sheet feed mode

In order to feed heavy stock, very small or very large sheets, embossed or even irregular shaped sheets, it may be necessary to feed the sheets manually.

The machine can be programmed and set up in exactly the same way as explained when operating the machine automatically. However, the paper gate must be raised to its highest position for the sheets to be fed freely.

The machine can now be started by activating the System switch to ‘on’.

the Compressor switch.

Do not activate

Select the icon on the touch screen and begin to slide the sheets individually through the paper gate until they are driven by the drive belts.

To stop feeding the sheets, select the

System Switch off.

icon on the touch screen and switch the

NOTE.

If the delay between feeding sheets is excessive, the system will time out.

SYSTEM

Page 31

Operating the DigiFold Pro

Store Pages.

To get to the Store setting page click the lower tab status area.

New Jobs.

or from the

Having set up your job you can give the job a name and save it to a store. You can also retrieve previously saved jobs, modify them or delete jobs you no longer require.

To create a new job name click in text area & keyboard will open to input job name.

Load existing job from store

Clicking to search currently stored jobs

Clicking to delete currently stored jobs

Clicking to save job shown.

Keyboard for entering job name.

Page 32

Return to Store Menu & click save icon job to store to save

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Save confirmation screen.

To confirm saving of job click here.

Search for current jobs to load or modify.

You can search for jobs by clicking the search icon search keyboard for text input.

, this will bring up the

Type in job description or first few characters

To change your mind & return to the previous screen click here.

Jobs matching characters in text box will be shown in this area — selecting job from this area will show job settings in the right hand status area. Job selected will be shown in text box.

Press search icon to start search

Toggle between search results & full list of jobs

Press to load job shown in text box.

SYSTEM

Page 33

Operating the DigiFold Pro

Loading job confirmation screen.

To cancel loading of

Job press here

To confirm loading of

Job press here

Loaded job may be modified and then re-saved as the same job name.

Overwrite job confirmation screen.

To cancel overwrite of

Job press here.

To confirm overwrite of Job press here

Delete job confirmation screen.

To cancel deletion of

Job press here

To confirm deletion of

Job press here

Page 34

FOLDING

DigiFold Pro

Operating the DigiFold Pro

Tools Menu.

To get to the Tools page click the lower tab

Inch paper in direction of arrow to clear jams

Click on Up Arrow to put Anvil into Top

Dead Centre position

(TDC)

Inch paper in direction of arrow to clear jams

Clicking this icon will show Machine programme revision &

Touch Screen software revision.

Machine main board software revision

Touch screen software revision

SYSTEM

Page 35

Operating the DigiFold Pro

BLANK

PAGE

Page 36

FOLDING

DigiFold Pro

The Blade Assembly

Adjusting the blade pressure (no paper required)

1. (i) Switch the power ‘on’ by turning the Emergency stop button clockwise to release the safety latch.

(ii) Select the Tools tab change to that shown below.

at the bottom of the touch screen, the display will

(iii) Activate the system switch to ‘ON’

(iv) Select the up arrow to move the blade to the Top Dead Centre position.

Click on Up Arrow to put Anvil into Top

Dead Centre position

(TDC)

2. Raise the exit guard

3. Using a 5mm allen key, unlock the socket head screws positioned at each end of the creasing blade.

4. Rotate the blade adjustment cams until they are just tight, and then back off slightly before tightening the socket head screws.

The diagram below demonstrates the adjustment of the blade pressure

5

SYSTEM

Page 37

Replacing Blade Sets

1. Before removing the blade assembly, ensure that the lower blade / anvil is at ‘Top Dead

Centre’, see page 37.

2. Lift the top cover.

3. Using a 5mm allen key, remove the two socket head screws, one each end of the Blade

Set, as shown in FIG 32.1 below.

FIG 32.1

4. Remove the Sheet Guide Assembly, by pulling upwards on the two flanges, one each end, as shown in FIG 32.2 and FIG 32.3 below.

Flange

Sheet Guide Assembly

FIG 32.2

FIG 32.3

5. The Blade Set can now be removed from the machine using the Blade Extractor Tools shown in FIG 32.4 below.

Blade Extractor Tools

FIG 32.4

Page 38

FOLDING

DigiFold Pro

Replacing Blade Sets

6. Insert the Blade Extractor Tools, one at each end of the Blade Set, as shown in

FIG 33.1 below.

Note The Position of The

Blade Extractor Tool

Under The Lip of The

Blade Adjuster Assembly

FIG 33.1

7. Lever the Blade Assembly in the direction shown in FIG 33.2 to unclip and release the

Blade Set.

FIG 33.2

SYSTEM

Page 39

Replacing Blade Sets

8. Slide the blade assembly out of the creasing unit and lay it on a flat surface.

9. Slide the blade adjustment cams and the blade adjustment assemblies away from the dowels located in the ends of the blades / anvils as shown in FIG 34.1 below.

FIG 34.1

10. Slide the blade adjustment assemblies and the blade adjustment cams onto the dowels of the new blade set.

11. Slide the new blade set into the slots of the creasing unit as shown in FIG. 34.2.

12. Rotate the blade adjustment cams until they are just tight, and then back off slightly.

Reset blade to ‘Top Dead Centre’ and make final adjustments.

FIG 34.2

Page 40

FOLDING

DigiFold Pro

Replacing Blade Sets

13. Refit the Sheet Guide Assembly

14. Close the top cover

15. Switch the machine on and test the crease for form.

The following Blade sets are supplied with the Digifold 5000P as standard.

Standard Blade set Part number 176-213-02

Consisting of a standard blade and anvil, pre-set for your machine.

Narrow Blade set Part number 176-213-01

Consisting of a standard blade and a narrow anvil, pre-set for your machine.

NOTE.

Blade sets are individually set for each machine at the point of manufacture.

Replacement Blade sets will therefore need to be set up by a factory trained service engineer.

Do not attempt to use a Blade set from another Digifold Pro.

SYSTEM

Page 41

Perforating

Once the machine is set-up, the Machine can be used to perforate or crease.

Notes

1. Perforating and creasing can be carried out simultaneously. However, if any adjustment is made to the roller tilt mechanism in order to compensate for the perforation line being ’out of square’, this may effect the accuracy of the crease. If this occurs creasing and perforating must be carried out as separate operations.

2. By adjusting the outfeed drive tyres relative to the drive hubs it is possible to stear the sheet, (i.e. By placing the tyre on top of the hub one side of the paper will stear faster on that side).

The components and tools required to install the perforator are contained in the despatch kit supplied with the machine, they are listed below.

1 off Set of standard perforation ‘28 tooth’ blades.

1 off Set of standard hardened anvils.

1 off 3mm bondhus wrench / allen key

1 off 2mm bondhus wrench / allen key

The perforator blades are split into two matching halves and are fitted to the drive wheels as shown in the photograph using the four screws supplied.

A hardened anvil is fitted to the drive hub as shown in the photograph also using the four screws supplied. Again the anvils are made from matching halves.

Important: The perforator blades are very sharp and care must be taken whilst handling.

Do not mix the matching pairs of blades or anvils.

Perforating ‘Spares’ kits

For perforating and other types of paper, various spares kits are available which can be assembled to the machine in the same fashion. They are listed below along with a range of scoring wheels,

Perforating blades

56 teeth Part Number

1-99-41

— Standard stock / fine perforations.

28 teeth Part Number

1-99-12

— Medium stock /

Medium perforations.

Anvils

20 teeth Part Number

1-99-10

— Heavy stock / coarse perforations.

Standard Part Number

1-99-35

— For all blade types

Page 42

FOLDING

DigiFold Pro

Perforating

All of the blades and anvils are supplied with fixings.

*Perforator stripper

Standard Part Number

177-05-01

*It is recommended that for multiple perforations, a separate perforator stripper is used for every perforating blade set fitted in the creasing unit.

Setting the machine

1. Turn the mains supply to the machine ‘off’.

2. Open the perforator assembly to get access to the drive wheels and hubs.

3. Locate and remove the blades / anvils from the despatch kit supplied with the machine.

4. Using the 2mm allen key (supplied), loosen the drive wheel that is to accommodate the blades.

5. Slide the drive wheel away from any obstructing drive wheels or hubs in order to mount the blades.

FIG 37.1

FIG 37.2

6. Using the 2.5mm allen key (supplied), take one half of the matching pair of blades and mount on to the drive wheel. Do not secure the blade.

7. Mount the other half of the blade to the drive wheel as shown (FIG 37.1). Secure the blades to the wheel ensuring not to over tighten grub screw.

8. Mark on a single sheet the desired perforating position. Feed the sheet through the machine manually until the mark can be seen. Use this mark to assist in fixing the position of the perforating drive wheel to the roller drive shaft.

9. Using the 2mm allen key, loosen the drive hub nearest the perforating drive. Slide the drive hub away from any obstructing drive wheels or hubs in order to mount the anvils.

10. Using the 2.5mm allen key, take one half of the matching pair of anvils and mount to the drive hub. Do not secure the anvil.

11. Mount the other half of the anvil to the drive hub as shown (FIG 37.2). Secure the anvils to the drive hub ensuring not to over tighten the grub screws.

SYSTEM

Page 43

Perforating

12. Slide the drive hub towards the perforating drive wheel until there is a clearance of 0.5mm (0.020”).

13. To prevent damage to the blades or the anvils, do not force the drive wheel against the hub.

14. Fix the perforator stripper adjacent to the drive wheel and blade as shown.

15. Operate the machine and test the perforations for form.

It is important that the drive hubs are arranged evenly across the width of the paper in order to reduce the risk of jamming.

For multiple perforations repeat the above procedure.

1

4

3

5

2

FIG 38.1

Fig 38.1

Demonstrates a typical set-up for perforating sheets.

1

2

3

— Perforating drive wheel with mounted blades

— Perforator stripper

— Standard drive wheel

4

5

— Drive hub with mounted anvils

— Standard drive hub

Always remove blades and anvils once the perforating operation has been completed to avoid marking on digital or delicate media.

Page 44

FOLDING

DigiFold Pro

Removing Paper Jams

Removing Paper Jams

In the event of a paper jam occurring, whilst running the machine, follow the steps described below to allow access to remove the jammed paper.

1. Unlock and lower the delivery unit, open the top cover and the perforator unit; see

FIG 39.1 below.

2. If the paper is jammed in the fold rollers; try to rotate the top fold roller, using both hands. Position the thumbs under the tie bar and spread the fingers out above the tie bar.

Tie Bar

Top Fold Roller

FIG 39.1

Top Cover

Delivery Unit

Perforator Unit

SYSTEM

Page 45

BLANK

PAGE

Page 46

FOLDING

DigiFold Pro

Trouble Shooting

Paper crease out of square

Check that the sheets are all square and exactly the same size before loading the stack on to the table.

Check that the adjustable side lay has been correctly positioned ie. No further than

0.5mm (0.020”) from the paper stack.

Check that the blade tilt mechanism is correctly set.

Crease Position Inaccuracy

Check that the crease profile has not been set too deep.

Check that the correct Blade Set is fitted. (Standard Blade Set for material thickness of 0.25mm (0.010”) and above, Narrow Blade Set for material thickness of

0.25mm (0.010”) and below).

Paper fold out of square

Note:- the best fold squareness is achieved when the fold is not on the center of the crease, but to one side or the other.

Check that the fold is to one side of the crease center line.

Check that the roller gaps are not too tight and squashing the crease.

Check that the roller gaps are not too large and allowing the paper to slide

(especially so on glossy paper).

Paper jamming

Check that the leading edge of the paper is not being damaged by the paper gate.

If this is occurring, check that the suction slot and the paper gate have been correctly set.

Check that the first crease / fold position is not too close to the leading edge of the paper. A minimum distance of 50mm (1.96”) is recommended.

If jamming is occurring in the Perforator — adjust the Hubs (see Pages 12 & 44).

SYSTEM

Page 47

Trouble Shooting

Machine will not start

Check the power supply to the machine.

Check that the emergency stop button has been released.

Check that the top cover is down.

Check that the perforator assembly is in its closed position.

Check that the delivery unit is in the up position, and located correctly, (the machine will not start if the delivery unit is not in its up position).

Paper not feeding

Check that the paper stack is not too high or too heavy for the feeder. The height of the paper stack should be defined by the weight and the size of the stock being creased.

Ensure that the adjustable side lay is not pressed against the paper stack. However, if the clearance between the adjustable side lay and the paper stack is too great, the air supply will escape instead of blowing through the paper thus making it difficult to feed.

Check that the clearance between the paper gate and the suction roller is not set too low.

On digital media, the feeding performance may be improved if the leading edge of the stack is trimmed before loading onto the Digifold.

Check that the air distribution has been correctly set.

Check that the air separation has been set high enough to feed the sheets.

For heavy stocks, very small or very large sheets, embossed or even irregular stock, it may be necessary to feed the sheets manually — see page 31.

Cracking of the Printed Material along the Crease.

Cracking of the material along the crease may be caused by the following:-

Pressure too heavy on the top blade — reduce pressure.

Cracking on one edge caused by misalignment of the anvil and blade.

When using dry ink or toner based print engines, the material must be fully acclimatised for at least 48 hours before putting an image onto the paper.

Page 48

FOLDING

DigiFold Pro

Trouble Shooting

Using the Correct Blade Set.

Two Blade sets are supplied with the machine.

The Standard Blade set is suitable for material thicknesses of 0.25mm (0.010”) and greater.

The Narrow Blade set is suitable for material thicknesses of 0.25mm (0.010”) and smaller.

If the Standard Blade Set is used to crease and fold materials less than 0.25mm

(0.010”) inaccurate results can be produced.

If the Narrow Blade Set is used to crease and fold materials greater than 0.25mm

(0.010”) cracking can occur. More importantly this could cause the main motor to temporarily stall. This probably won’t be that noticeable until you look at the results, whereby the crease position will vary.

SYSTEM

Page 49

Trouble Shooting

Error Screens

Sheet did not arrive.

If the machine stops and error message 01 is displayed on the touch screen, this indicates that the paper did not arrive at the end of the suck process; so the machine timed out. Press the green tick button and then press the start button.

Paper Crunch

If the machine stops and error message 02 is displayed on the touch screen, this indicates that a paper jam has been detected.

Press the system switch down and then select the right or left arrows, to inch the paper forwards or backwards. See page 39 that describes how to remove paper jams.

Press the green tick button and then press the start button.

Double Sheet Feed

If the machine stops and error message 03 is displayed on the touch screen, this indicates that a double sheet feed has been detected. Check that the paper gate has been set correctly. Press the green tick button and then press the start button.

Blade Not Home

If the machine stops and error message 04 is displayed on the touch screen, this indicates that the lower blade / anvil has not made contact with the HOME switch.

i.e. blade still in top position. Switch the machine off and remove the blade set and ensure that the area is free from obstructions. Return the blade set to the creasing unit and switch the machine on. Operate the machine in the normal sequence, if the display continues to read error message 04 it is advised to contact a Service Engineer immediately.

Page 50

FOLDING

DigiFold Pro

Trouble Shooting

Error Screens (Continued)

Blade Busy

If the machine stops and error message 05 is displayed on the touch screen, this indicates that the blade is busy. Try to operate the machine again, If this fails it is advised to contact a Service Engineer.

Blade Home Failure 1

If the machine stops and error message 06 is displayed on the touch screen, this indicates that there may be some creasing errors, and that the creasing pressure should be checked, (also check for a double that may have got through, causing this error).

Blade Home Failure 2

If the machine stops and error message 07 is displayed on the touch screen, this indicates that the crease blade did not get back to its home position correctly or at the correct time. Causes, can be excessive blade pressure (suspect a double), or

Some kind of jam which caused more than one sheet thickness to be creased.

SYSTEM

Page 51

Trouble Shooting

Error Screens (Continued)

Flying Home Failure

If the machine stops and error message 08 is displayed on the touch screen, this indicates that the home signal was missed during creasing. Check that the blade pressure is not too high.

Clip 1 NOT clear

(Back Sensor)

If the machine stops and error message 09 is displayed on the touch screen, this indicates that the sensor is or was blocked when it should have been clear.

i.e. A jam in the paper path or the wrong length of paper has passed through the sensor.

To correct — check if paper is present and check that the paper path is clear before restarting. See page 39 that describes how to remove paper jams.

Clip 1 NOT Blocked

(Back Sensor)

If the machine stops and error message 10 is displayed on the touch screen, this indicates that the sensor did not see the paper at the correct time.

i.e. A jam in the paper path.

To correct — Check if paper has jammed in the machine prior to the sensor.

See page 39 that describes how to remove paper jams.

Clip 2 NOT clear

(Top Sensor)

If the machine stops and error message 11 is displayed on the touch screen, this indicates that the sensor is or was blocked when it should have been clear.

i.e. A jam in the paper path or the wrong length of paper has passed through the sensor.

To correct — check if paper is present and check that the paper path is clear before restarting. See page 39 that describes how to remove paper jams.

Page 52

FOLDING

DigiFold Pro

Trouble Shooting

Error Screens (Continued)

Clip 2 NOT Blocked (Top Sensor)

If the machine stops and error message 12 is displayed on the touch screen, this indicates that the sensor did not see the paper at the correct time.

i.e. A jam in the paper path.

To correct — Check if paper has jammed in the machine prior to the sensor.

See page 39 that describes how to remove paper jams.

SENSOR POSITIONS

Clip 2

(Top Sensor)

Clip 1

(Back Sensor)

Overlap

If the machine stops and error message 13 is displayed on the touch screen, this indicates that the ‘Lead Edge Sensor’ has seen a sheet subsequent to the first one as being longer. Again this could actually be a longer sheet, OR it could be a sensor problem (if it is a recurring problem). Check that the paper gate has been set correctly.

SYSTEM

Page 53

Trouble Shooting

Recommended weekly operator maintenance

Clean all sensors.

The lead edge sensor housing is located on the layedge side of the machine between the input roller shafts. With a slim brush the sensors can be cleaned when required. Pass the brush under the ball holder and push through until it passes the infeed rollers. Alternatively it can be blown with compressed air.

The Jam Sensor is situated just after the edge sensor and is inline across the paper path with the receiver in the operator side sideplate. This is not usualy sensitive to dust but if required can be blown with compressed air.

Clip 1 sensor is situated on the lower guides beneath the delivery conveyor and can be cleaned when required using a slim brush.

Clip 2 sensor is situated on the upper guides inside the top cover and can be cleaned when required using a slim brush.

Clean in feed rollers and output drive hubs using the cleaning kit supplied

(cleaning kit part number 90-018).

Remove and clean the blade assembly.

Technician Maintenance

It is recommended that your Machine is fully serviced at least once every six months by a factory trained Service Engineer.

Page 54

FOLDING

DigiFold Pro

BLANK

PAGE

SYSTEM

Page 55

170-95-02

DISPATCH KIT

ITEM PART NUMBER QTY

1

174-025

DESCRIPTION

1 OPERATORS MANUAL DigiFold Pro

2 90-018

3 650-040

4

170-009-01

5

601-167

1 ROLLER CLEANING KIT

1 POWER CORD C19 UK 16A 2.5m

2 BLADE REMOVAL TOOL

1 DIGITAL THICKNESS GAUGE

6

7

403-01-030-006

409-01-040-004

8

9

620-007

620-020

10

11

620-026

620-027

12

13

624-025

170-002-01

14 624-018

15

16

17

18

1-99-35

1-99-12

613-229

65-104

12 SCREW — SOCKET CAP HEAD — M3 x 6 LG

1 SCREW — SKT. SET FLAT PT. — M4 x 4 LG

1 HEXAGON BALL DRIVER 2mm

1 HEXAGON BALL DRIVER 2.5mm

1 BONDUS L WRENCH 4mm

1 BONDUS L WRENCH 5mm

1 STATIONERY TUBE 330MM X 50MM

1

QUICK START CHART

1 DISPATCH BOX

1 SLITTING ANVIL SET

1 SLITTER PERF BLADE 28T

1 WRITE-ON SERIAL NO. LABEL

1 SPECIFICATION LABEL MSL/CE

Page 56

FOLDING

DigiFold Pro

ACCESSORIES AND OPTIONS

ITEM

6

7

4

5

8

9

1

2

3

PART NUMBER

172-022-01

1-99-10

1-99-12

1-99-41

1-99-35

172-03-01

172-04-01

173-169-01

176-213-03

DESCRIPTION

LOADING TABLE EXTENSION

PERFORATING BLADE SET 20T (Card)

PERFORATING BLADE SET 28T (Single Sheets)

PERFORATING BLADE SET 56T (Fine Perforations)

ANVIL SET USED WITH ABOVE BLADE SETS

DOUBLE SHEET DETECTOR KIT

NARROW SHEET KIT

ETHERNET KIT

DYNAMIC BLADE SET — ULTRA NARROW

ACCESSORIES….

….May be obtained from your dealer and fitted to your machine using the instructions supplied, or by reading your operators manual.

OPTIONS….

….May also be obtained and fitted by your dealer. You should not attempt to fit options as specialist tools and knowledge are required.

SYSTEM

Page 57

RECOMMENDED SPARES

PART NO.

DESCRIPTION

125-21-02 Dual Stepper Driver Board

125-25-01 Small Stepper Driver — High Power

174-06-01 Small Stepper Driver — Low Power

174-01-02 Controller PCB Assembly + Chip

174-19-01 RS232 Adaptor PCB Assy.

75-472-01 Mini ITX Motherboard (Configured)

126-059-02 Link — Paper Guide

128-026-03 Delivery Belt

145-093-02 Knife Driver Pin — M8

76-261 Lead — Delivery Input Connector

173-57-01 Lead — Blade Position Sensor

173-45-01 Lead — Tilt Pot

173-46-01 Lead — Gap Set 3 Pot

173-47-01 Lead — Gap Set 2 Pot

173-48-01 Lead — Gap Set 1 Pot

173-06-01 Power Supply — 48V

173-06-02 Power Supply — 24V

76-272 PSU Assembly — ATX12V — 300W

173-49-01 Stepper Motor — Dynacrease

76-240

76-257

Stepper Motor — Drive

Stepper Motor — Fold Knives

175-31-01 Input roller Assembly — Lower

175-31-04 Input Roller Assembly — Upper

175-042-01 Feed Belt

175-10-01 Edge Sensor Assembly

75-06-01 Touch Screen Assembly — 7”

175-11-01 Sensor Bar Assembly

175-11-02 Sensor Bar Assembly — Clip

175-11-03 Sensor Bar Assembly

175-12-01 1st Blade Assembly

175-12-02 2nd Blade Assembly

175-125-01 Connecting Link Assembly — Drive

175-125-02 Connecting Link Assembly — Knife Hubs

175-29-01 Fold Roller — 1st

175-29-02 Fold Roller — 2nd

175-29-03 Fold Roller — 3rd

175-29-04 Fold Roller — Fixed

Page 58

FOLDING

DigiFold Pro

RECOMMENDED SPARES

PART NO.

DESCRIPTION

172-05-01 Paper Gate Assembly

175-21-01 Vacuum Roller Assembly

176-02-01 Blade Adjuster Assembly

176-081-01 Worm Wheel — Gap Set

176-213-01 Dynamic Blade Set — Narrow

176-213-02 Dynamic Blade Set — Standard

177-01-01 Perforator Assembly

602-160 Plain Bush — Dynacrease Guide Block

604-100

604-103

Gas Spring — Perf. Unit

Gas Spring — Delivery

607-005

607-045

Belt — Vacuum Roller

Multi Beam Coupler

607-171

607-175

607-183

613-023

681-011

681-019

613-351

613-365

Timing Belt — Drive

Belt — Drive

Timing Belt — 190XL 062

Fuse 3.15A — 20 x 5mm Fast Blow Ceramic

Fuse — 315mA — 20 x 5mm Anti-surge — Ceramic

Fuse — 6.3A — 20 x 5mm — Anti-surge Ceramic

Micro Switch — Guard

Emergency Stop Switch — Double Pole

626-007

652-011

652-043

Anti-Static Sensor Bar

Switch — Low Current Coil — Black

Switch Thermal O/Load 20A Black

75-258 Anti — Static Transformer

175-28-01 Butterfly Valve — Stepper

76-262

76-258

76-259

76-266

Stepper Motor — Roller Drive

Stepper Motor — Belt Drive

Stepper Motor — Roller Position

Lead — Fold Knives Sensor

124-01-27 Lead — Delivery Roller Pot

175-072-01 Lead — Jam Detector — Emitter

175-072-02 Lead — Jam Detector — Receiver

NOTE…..

The items listed above represent parts which are subject to wear, loss, or accidental damage, and is included for your guidance only.

Replacement of parts fitted to your machine require specialist knowledge and should therefore be entrusted to your dealer.

SYSTEM

Page 59

MACHINE CALIBRATION HISTORY

Serial Number:-

Date:-

Total Count:-

Vac Suck Trim

Vac Park Trim

Stretch

Lead Edge Trim

Follow Stretch

Del. Roller Trim

Knife 1 Trim

Knife 2 Trim

K1 Deflect Trim

K2 Deflect Trim

K1 Travel

K2 Travel

Date:-

Total Count:-

Vac Suck Trim

Vac Park Trim

Stretch

Lead Edge Trim

Follow Stretch

Del. Roller Trim

Knife 1 Trim

Knife 2 Trim

K1 Deflect Trim

K2 Deflect Trim

K1 Travel

K2 Travel

Date:-

Total Count:-

Vac Suck Trim

Vac Park Trim

Stretch

Lead Edge Trim

Follow Stretch

Del. Roller Trim

Knife 1 Trim

Knife 2 Trim

K1 Deflect Trim

K2 Deflect Trim

K1 Travel

K2 Travel

Page 60

FOLDING

DigiFold Pro

FUSE POSITIONS & RATINGS

(POSITION ET CLASSIFICATION DES FUSIBLES)

PSU (5V / 24V)

(FUSIBLE PSU (5V/24 V)

F3.15AH 250 (613-023)

SPARE FUSE

POSITION

(POSITION PORTE

FUSIBLE)

SPARE FUSE

POSITION

(POSITION PORTE

FUSIBLE)

PSUs (24V & 48V)

(FUSIBLE PSUs (24 V & 48 V)

T6.3AH 250 (681-019)

ANTI-STATIC UNIT

(FUSIBLE ANTI-STATIQUE)

T315mAH 250 (681-011)

SYSTEM

Page 61

PRODUCT RECYCLING & DISPOSAL

European Union

Disposal Information for Commercial Users

Application of this symbol on your equipment is confirmation that you must dispose of this equipment in compliance with agreed national

Procedures.

In accordance with European legislation end of life electrical and electronic equipment subject to disposal must be managed within agreed procedures.

Prior to disposal please contact your local dealer or representative for end of life take back information.

Disposal Information for Domestic Users

Application of this symbol on your equipment is confirmation that you should not dispose of the equipment in the normal household waste stream.

In accordance with European legislation, end of life electrical and electronic equipment subject to disposal must be segregated from household waste.

Private households within EU Member States may return used electrical and electronic equipment to designated collection facilities free of charge. Please contact your local disposal authority for information.

In some Member States when you purchase new equipment your local retailer may be required to take back your old equipment free of charge. Please ask your retailer for information.

Other Countries

Please contact your local waste authorities and request disposal information.

Page 60

FOLDING

DigiFold Pro

SYSTEM

Page 61

10 898 торговых марок 3 788 000 инструкций	Скачайте инструкцию БЕСПЛАТНО! Diplodocs позволяет скачать несколько типов инструкций для наилучшего использования MORGANA DIGIFOLD 5000P

Вам требуется помощь по использованию изделия? Все инструкции по категориям

инструкция по эксплуатации MORGANA DIGIFOLD 5000P Diplodocs поможет скачать инструкцию MORGANA DIGIFOLD 5000P — ILLUSTRATED PARTS MANUAL . Введите модель изделия MORGANA… Предварительный просмотр первых 3 страниц инструкции У вас отключен JavaScript или устаревшая версия Adobe Flash Player Обновить Flash player

Copyright © 2005 — 2012 — Diplodocs —
Все права защищены.
Торговые марки принадлежат их соответствующим владельцам.