Nero radio 8113 ip55 инструкция

Single-channel radio receiver

to connect an optocentor, photo cells and other safety sensors

Description

1.1 Usage

The radio receiver Radio 8113 IP is designed to operate

motors of gates, garage doors, awnings, blinds, roller shutters

as well as light and other electric devices.

1.2. Technical characteristics

Supply voltage, V/ Hz ………………………………………………………………………~230 (+10%, -15%) / 50

Max switched current, A …………………………………………………………………………………………………..3

Switched voltage, V ……………………………………………………………………………………………~250 / =30

Number of operated motors ………………………………………………………………………………………………1

Working frequency, MHz ……………………………………………………………………………….434,42 ± 0,37

Working distance in open space, m …………………………………………………………………………………100

Memory …………………………………………………………………………………………………36 remote controls

Dimensions, mm ………………………………………………………………………………………………..80? 80? 55

Ambient temperature, °Ñ ……………………………………………………………………………….. îò -20 äî +65

Working conditions ………………………………………………………………………………….indoors, outdoors

IP protection class ……………………………………………………………………………………………………….IP65

Protection class under GOST 27570 …………………………………………………………………………………II

Conformity ………………………………………………………………………………………………………………….CE

1.3. Working modes of Radio 8113 IP

1) «Other automation units»: the mode is used to connect a Radio 8113 IP to another automation

device that operates roller shutters, gates, or garage doors. The signal is transmitted 1,5 seconds

(i.e. voltage is supplied to the automation device for 1,5 sec).

2) «Roller shutters»: the mode is used to connect a Radio 8113 IP directly to a roller shutter motor.

The signal can be programmed from 0,2 to 180 seconds. The factory preset is 60 seconds.

3) «Outdoor blinds»: the mode is used to connect a Radio 8113 IP directly to a blinds motor to

open/close blinds and turn their lamellas horizontally. he signal can be programmed from 0,2 to 180

seconds. The factory preset is 120 seconds.

4) «Light and other electric devices»: the mode is used to connect a Radio 8113 IP directrly to a

lighting unit or any other electric device. The signal is transmitted until the «stop» signal has been

activated with a remote control or a switch (needs to be connected to the Radio 8113 IP).

The following contacts are used to:

1 —

connect to N of ~230 V supply main

2 — connect to L of

~230 V supply main

3 —

connect the «N » cable of the motor

4 — connect the «up» cable of a motor (black or

brown).

5 — connect the «down» cable of a motor.

6, 7 — bridge A to connect L of supply main to

executive relays in the receiver.

8 — safety sensor.

9 — connect to «up» output of the switch.

10 — connect to «down» output of the switch.

11 — connect to «common» output of the switch

and sensor.

12- common contact for antenna connection.

13 — input of antenna.

Fig. 1. Connection scheme for Radio 8113 IP

Bridge

contacts

4 and 5

Button

Remove bridge

from contacts

6 and 7

Connect to the button input of control block

for gates, garage doors, barriers

Fig. 2. Scheme that shows how to connect

Radio 8113 IP to a step-by-step input (open-

stop-close) of a control block for operation

of gates, barrier arm gates or of a garage

door motor.

* View how to connect an optosensor on page 2.

(no ground connection required)

Switcher of safety

Antenna

sensor modes

.

.

.

Safety

fuse

Motor

Bridge

Safety sensor*

Button

Incandescent

220/230V lamp

Electric load

up to 690W

Fig. 3. Scheme that shows how to connect

Radio 8113 IP to a lighting unit or other

electric devices.

Radio 8113 IP

2. Programming

2.1. Programming modes:

1) programming remote controls;

2) programming scenario switches;

3) setting working modes of Radio 8113 IP.

2.1.1. Programming remote controls mode

a) Programming remote controls into the memory of Radio 8113 IP:

Press and hold the programming button more until the LEDs flash red and green.

The LED will continue to blink red during the entire process of remote controls programming.

Press the button of the remote control you want to programme. The LED will flash green three

times to signal that the button of the remote control has been programmed.

Note: if the LED flashes green only one time, it signals that the button has been previously

programmed into the memory of the receiver Radio 8113 IP. If the LED blinks red and green, it

signals that the memory of Radio 8113 IP is full, and the button can not be programmed..

In case you need to programme several buttons, press the desired buttons one by one.

To finish programming, press the programming button one time. The LED signals the end of

programming with two red and green flashes.

b) Deleting ALL remote control from the memory of Radio 8113 IP:

Press and hold the programming button until t

Again press and hold the programming button more than 4 seconds until LED 2 flashes red

twice. Release the programming button.

To come back to the standby mode, press the programming button one time.

c) Deleteing the desired button(s)/remote control(s) from the memory of Radio 8113 IP:

Press and hold the programming button until the LEDs flash red and green.

The LED will continue to blink red during the entire process of remote controls deleting.

Press and hold the button of the remote control you want to delete more than one second. When

LED 2 flashes red, release the button.

In case you need to delete several buttons, press and hold the desired buttons more than one

seconds one by one.

To finish deleting, press the programming button one timer. The LED signals the end of

programming with two red and green flashes.

2.1.2. Programming scenario switches mode

Press and hold the programming button until the LEDs flash red and green.

Press the button of the scenario switch you want to programme. The LED will flash green and

red and then continue to blink red during the programming session.

For further steps, please, see the corresponding manual on Radio 8105-50-4, Radio 8105-50-6,

Radio 8105-50-8.

2.1.3. Setting working modes of Radio 8113 IP

Press and hold the programming button until the LEDs flash red and green.

Press the programming button. The LED flashes red and green to indicate that Radio 8113 IP

has entered the mode, where you can set the necessary working regime (mode) of the receiver

(see the modes description in point 1.3).

Count how many times the LED blinks green to determine the current working mode. The

LED 1

number of green blinks indicates the chosen working mode (see the table below). The factory

preset is roller shutters mode with the 60-second signal.

LED 2

Programming

No.

Working mode

button

Switch

Other automation units

Roller shutters

Outdoor blinds

Light and other electric

devices

To finish setting the working mode of Radio 8113 IP, select one of the two options:

a) to remember the selected working mode and signal duration: press the programming button one

time. The LED signals the end of programming with two red and green flashes.

b) to ignore the selected working mode and signal duration: wait for 32 seconds until Radio 8113 IP

leaves the programming mode itself. The LED signals the return to the standby mode with two

green and red flashes.

2.2. Setting signal duration for roller shutters mode or for outdoor blinds mode

Switch off the Radio 8113 IP power.

Connect a switch (see fig. 1).

Switch on the power.

Follow the first three steps of point 2.1.3.

Select the desired working mode if necessary (see the table above).

Close the roller shutter or blinds with the connected switch.

Open the roller shutter or blinds with the connected switch.

In five seconds after the roller shutter or blinds reach the upper position, stop the object by

pressing shortly the DOWN button of the switch.

Press the programming button one time. The LED signals the end of setting signal duration

with two green and red flashes.

with a possibility

he LEDs flash red and green

How to switch to

How LED signals

the next mode

switching to

the next mode

Press and hold the programming

button more than 1 second

Press and hold the programming

button more than 1 second

Press and hold the programming

button more than 1 second

Press and hold the programming

button more than 1 second

.

Indication

How Led signals

the chosen

working mode

Предложите, как улучшить StudyLib

(Для жалоб на нарушения авторских прав, используйте

другую форму
)