Orbis data micro 2 инструкция

DATA MICRO + / DATA MICRO 2+

OPERATING INSTRUCTIONS

Increment or move up

in menu

Circuit C2 override

(only Data Micro 2 +)

C

Move back in menu

Permanent override

(C+C1 ó C+C2)

On / Off

Programming

Circuit 2

(only Data Micro 2 +)

Day of the week

(1) Monday

AM / PM mode

Hour : Minute

Circuit 1

On / Off

DESCRIPTION

+

DATA MICRO

is a time switch designed to control any electrical installation.

Includes pulse programming from 1 to 59 seconds and up to 32 block memory

spaces. Automatic winter ! summer official time adjustment.

INSTALLATION

ATTENTION: Electrical devices must be installed and assembled by authorized

installer.

VERY IMPORTANT: This time switch is protected internally against interference by a

safety device. However, particularly strong electromagnetic fields may alter its

operation. Such interference can be avoided by adhering to the following

recommendations during installation:

— The device should not be installed near inductive loads (motors, transformers,

contactors, etc)

— A separate power line is recommended (equipped with a network filter if

necessary)

— Inductive loads should be equipped with interference suppressors (varistor, RC

filter)

If the time switch is to be used in combination with other devices in an installation, it

is necessary to verify that no parasitic disturbances will be caused by the group.

MOUNTING: Electronic control device for independent installation in distribution

cabinet fitted with symmetrical 35 mm profile in accordance with the standard EN

60715 (DIN Rail EN 60715 (Rail DIN).

CONNECTION:

Connect according with the following schema:

DATA MICRO +

L

1

2

3

N

STARTING UP AND PROGRAMMING

+

DATA MICRO

is already programmed with current date and time, and with the

official automatic winter ! summer official time adjustment activated (last Sunday in

March and last Sunday in October).

Programming is based in menus (indicated by icons):

— Programming.

— Clock setting.

— Winter / summer official time change.

— Holidays period programming.

DIGITAL TIME SWITCH

Display

Decrement or move

down in menu

Circuit C1 override

C2

C1

OK

MENU

Confirms the selection

Starts menu

Clock setting

Summer / Winter time

Holidays program

Pulse

Override

Permanent overrride

DATA MICRO 2 +

4

5

6

L

1

2

3

N

RESET

Although the clock of the device is already programmed, if a RESET is needed

(blank display, inconsistent data, etc), press at the same time the four keys during 3

seconds. In this moment, the device loses all data and goes to clock setting mode,

directly to program year, month, day, day of the week, hour and minutes.

CLOCK SETTING. FIG 1.

For clock setting, press key

select icon

and press

blinking; update the year by pressing keys

.

The same operation should be made to update month, day, day of the week, hour

and minutes. By accepting minutes with

To change the time mode (24h/12h am-pm) proceed as follows: accept year, month,

day and day of the week; while hour is blinking, press

time. After that, the time mode has change.

PROGRAMMING. FIG 2 and 3.

To program the device, press

menu

is entered and the display shows the first programmed switching. If no

switching is programmed then — — : — — is shown. To program or edit the desired

switching press

again, with keys

switching: C1 OFF, C1 ON, C1 ON

DATA MICRO 2+). Validate with

validating then with

. Then select the days of the week that the switching has to

operate. With keys

and

week that the switching has to operate and then fix it by pressing

sequence with the other days of the week when the switching has to operate. For the

days not desired, press

to go down to the next day. After programming all the

days of the week, the display will show the next switching to program.

SHORT TIME SWITCHING (PULSE) PROGRAMMING. FIG 4.

If the selected switching is a Pulse

pulse starts, use keys

and

59 seconds). This length is shown in the digits of seconds (situated at the right side

and smaller than the digits of hours and minutes). Select the day(s) of the week

when the switching has to be programmed and validate with

to come back to normal mode. If

two minutes, the device returns to normal mode.

VIEWING PROGRAMMED SWITCHING. FIG 5.

The programmed switching can be checked by entering again in menu

pressing key

all the switching are shown in display, and after the last one, the

display shows — — : — -, if there is any free space and then it shows the number of free

spaces.

EDITING OR DELETING SWITCHING

Programmed switching can be edited or deleted in menu

or

the switching to be edited or deleted. To edit it, proceed as in clause

PROGRAMMING and to delete it, keep pressing key

To delete all the switching without using RESET, go to the point where the display

shows the free spaces of memory, keep pressing key

. The display will show 32, the total free memory spaces.

MANUAL OVERRIDE. FIG 6.

In normal mode, pressing key

The same for circuit C2 by using key

If any manual override is executed, it is represented in display by symbol

The next programmed switching cancels the manual override and the symbol

disappear from the display.

PERMANENT OVERRIDE. FIG 7.

This option blocks all the programmed switching. In normal mode, keep pressing key

and then press key

(

this situation is indicated in display with symbol

can be changed by pressing key

To cancel permanent override keep pressing key

(

), symbol

disappear from display. The same for circuit C2 using key

(

) only in DATA MICRO 2+.

WINTER / SUMMER OFFICIAL TIME CHANGE. FIG 8.

Enter MENU by pressing key

validate with

. There are the three following working modes:

AUTO: The clock is automatically changed on the last Sunday in March al 02:00

and the last Sunday in October at 03:00.

PRO: Allows to choose the date and time for the time change, programming first

the winter ! summer change (

OFF: No time change will be made

HOLIDAY PROGRAM. FIG 9.

This function allows deactivating the circuits during a period of time up to 99 days.

After that, the programming continues as usual.

If user validates 0 days, the holiday period is cancelled and the device will work in a

normal way. If user validates a number of days different than 0, the device starts

immediately, so relays switch to OFF and programmed switching will not execute.

If the validated number of days is 1, the holiday period will finish at 23:59:59 of the

same day than validation. If the validation number of days is 2, the holiday period will

finish next day. And so on.

Display shows symbol

during the holiday period.

to access to the Menu and with keys

. Display shows the year with the last two figures

and

and validate it with key

, it automatically goes to normal mode.

and

to enter to the menu. By pressing again

and

select the circuit and type of

, (C2 OFF, C2 ON, C2 ON

and introduce hour and minutes desired,

place the blinking cursor on the first day of the

, after introducing hour and minutes when the

to program the length of the pulse (from 1 to

. After that, press

is not pressed, being in any mode, after

, selecting with keys

and then press key

and then press key

(

), circuit C1 is activated or deactivated.

(

) (only in DATA MICRO 2+).

) to activate the permanent position of circuit;

. After that, the state of the circuit

(

).

and then press key

; select option

using keys

) and then the summer ! winter change (

and

at the same

the

only in model

. Repeat this

and

.

.

and

,

).

• Home
• Brands
• Orbis Manuals
• Timer
• Orbis DATA MICRO 2+

4 docs – User Manuals, Help Guides and Specs – for the Orbis DATA MICRO 2+ product are present in our data base.

Tips for Finding Manuals:

This web-page provides a list of 4 accessible operating manuals and information books describing Orbis DATA MICRO 2+.
All manuals and instructions for Orbis DATA MICRO 2+ are introduced in an easy-to-use PDF format and may be gratuitously downloaded or looked through directly from the site.

The page offers the following types of manuals: Timer.

Helpful hints: While selecting a necessary guide for Orbis DATA MICRO 2+ one should pay special attention to the type of the document.
We try to supply you with the fullest possible set of papers we or our users are able to find. These may be overviews and specifications of the device, mounting and installing instructions, the unit operating rules and maintenance regulations and much more.

Haven’t found a required manual for your Orbis DATA MICRO 2+?

Check in a while. We update our guides collection and add new documents on a daily basis for you to be always able to find the very paper you need on our web-site. In case you own a directory or an instruction for Orbis DATA MICRO 2+, which is absent on our site, and you’d like to share it with the public, please send it to us as a scanned copy or a PDF file, and we’ll definitely place it on our page while providing your name as a supplier of the doc. Lots of our users will be grateful for your assistance!

612888