Радиоприемник tecsun pl 680 инструкция

• Contents

• Table of Contents

• Troubleshooting

• Bookmarks

Summary of Contents for Tecsun PL-680

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

FEATURES

FM-stereo/MW/LW/SW/SW SSB/AIR band with high sensitivity,

selectivity and user-friendliness

FM band coverage: 76 – 108 MHz

Shortware Single Side Band (SSB) with upper sideband (USB)

and lower sideband (LSB)

Equipped with Synchronous Detector and Dual Conversion

technology for MW band; this greatly enhances the receiver’s

sensitivity, selectivity, image rejection, and interference from

adjacent stations

FM/SW external antenna jack sensitivity selector: DX/Normal/

Local antenna gain

Multiple tuning methods

Store up to 2000 stations (manually, semi-automatic and fully

automatic)

Equipped with a high-sensitivity acoustic speaker with treble/bass

tone control switch (FM-stereo via earphone)

Auto Alarm-Off Timer: when the alarm goes off, the preset radio

station will play for 1-90 minutes

Sleep timer (1-120 minutes) to turn off the radio automatically

User-friendly interface

Built-in charging function

Powered by 4 x AA (R6) size batteries, DC 6V

Luxury carrying case

Dimensions: 188 x 116 x 31 mm

• 18, TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au flashing 16 PL-680 There are three tuning step speed settings: slow, fast, and intelligent (slow & fast). In Frequency Mode (VF), press & hold the [STEP] button to select your preferred setting. The intelligent tuning step notices when you rotate the…

• 8, TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au Press the [POWER] button to turn on your radio, then select your desired band by pressing [FM], [AM], SW [ ] / [ ], or [AIR] button. In case of receiving FM/AIR/SW broadcasting, fully extend the telescopic antenna for a better reception. When rec…

• 9, Tecsun PL-680 TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au METHOD 3: DIRECT KEYPAD ENTRY 1. Press the [VF/VM] button to enter the frequency mode (VF), the frequency display flashes twice. 2. Press the numeric keys [0] — [9] to enter the station frequency directly. Notes: 1. Ignore the decimal point for FM ba…

• 12, Tecsun PL-680 TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au 10 PL-680 WORKING WITH STATION MEMORIES DELETE MEMORY Press the [VF/VM] button to enter the memory mode; the memory address shows in the upper right corner of the display. METHOD 1: DELETE SINGLE MEMORY Rotate the [TUNING] knob to select the memory th…

• 22, TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au 20 PL-680 SETTING FM FREQUENCY RANGE: Press & hold the [FM SET] button until 88-108MHz, 76-108MHz or 87-108MHz appears on the display. Press the [FM SET] button to select a suitable frequency range for FM. TURN ON/OFF THE LW: To turn ON/OFF LW, press…

• 11, TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au PL-680 9 METHOD 3: ATS (AUTO TUNING STORAGE) FM ATS: 1. Fully extend the telescopic antenna and press the [FM] button to select FM band. 2. To automatically store all available stations, press & hold the [FM] button; «PRESET» will flash …

TECSUN

PL-680

TECSUN ELECTRONIC IND. LTD.

OPERATION MANUAL

PLL SYNTHESIZED RECEIVER

FM STEREO / MW / LW / SW-SSB / AIR BAND

TECSUN ELECTRONIC IND. LTD.

Address: Rm 11, 13/F, Block A, Hoi Luen Ind. Ctr.,

55 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong.

Website: www.tecsun.com.cn

TECSUN

RADIOS AUSTRALIA

TECSUN

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: +61 2 9939 4377

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au PL-680 19 When receiving AM broadcasting, if there is interference from adjacent strong signals, you improve the reception. 1. Press the [SYNC] button to select between “ ” or “ ” for optimum reception. 2. To deactivate the SYNC function, press the [SYNC] button until both » » and » » symbols are no longer on the display. Notes: If the «SYNC» symbol keeps flashing, this indicates that the r

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au 20 PL-680 SETTING FM FREQUENCY RANGE: Press & hold the [FM SET] button until 88-108MHz, 76-108MHz or 87-108MHz appears on the display. Press the [FM SET] button to select a suitable frequency range for FM. TURN ON/OFF THE LW: To turn ON/OFF LW, press & hold the [LW ON/OFF] button until «LW ON» or «LW OFF» appears on the display. SETTING MW (AM) TUNING ST

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au flashing Select the band of your desired station, then press the [VF/VM] button to enter the memory mode; the memory address shows in the upper right corner of the display. Press the [- PAGE +] button to select the memory page in which to search for stored stations using any of the below memory tuning methods. METHOD 1: MANUAL MEMORY TUNING Rotate the [TUNING] knob to tune around the stored stations. METHOD 2: AUTO BROWSE MEMO

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au 10 PL-680 WORKING WITH STATION MEMORIES DELETE MEMORY Press the [VF/VM] button to enter the memory mode; the memory address shows in the upper right corner of the display. METHOD 1: DELETE SINGLE MEMORY Rotate the [TUNING] knob to select the memory that you want to delete, press & hold the [DELETE] button with “ ” flashing; then press the [DELETE] button to remove the unwanted memory address. Note: If “

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au 1. Open the battery compartment located on the back of the unit; install 4 x UM3 AA size batteries observing the battery polarity diagram on the back of the radio. Close the battery door. Connect the unit to the regulated power supply. 2. Press the [POWER] button to turn on the radio. Not

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au LCD DISPLAY MHz A B SL EEP kHz Timer A PAGE PRESET mb SLOW Ni-MH Battery FM MW LW Shortwave BW FAST Timer B Charge 0 1 2 3 4 5 SYNC AIR 1 2 3 4 5 6 7 8 9 10 11 1213141516 18 19 17 0 1 2 3 4 5 0 1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 4 PL-680 19 Battery Consumption indicator “ ” : Full “ ” : Empty Signal Strength indicator “

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au PL-680 15 When the alarm goes off, press the [LIGHT/SNOOZE] button to temporarily turn off the alarm. The alarm will go off again after 5 minutes. Notes: 1. To turn off/on the alarm, press the [TIMER A] or [TIMER B] button; the alarm is activated when the » » or » » symbol is displayed. 2. When the alarm goes off, press the [POWER] button once to deactivate the «Alarm Off Timer»; press it twice to turn off the radio. 3. If the preset alarm is activated

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au WORKING WITH STATION MEMORIES PL-680 11 AUTO SORTING MEMORY To sort all stored stations automatically, turn the device off, then press and hold the [ ] button for 2 seconds until the memory page number in the upper right corner starts running. This function is able to: 1. Remove duplicate stations. Especially useful after storing stations manually, as you might store a station more than once. 2. Sorting the sequence of stored stations. – In page P0, select your desired band to find all stored stations in seq

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au Press the [POWER] button to turn on your radio, then select your desired band by pressing [FM], [AM], SW [ ] / [ ], or [AIR] button. In case of receiving FM/AIR/SW broadcasting, fully extend the telescopic antenna for a better reception. When receiving MW and LW broadcasting, please rotate the radio or change its location to achieve optimum reception. You can rotate the [VOLUME] knob to adjust to an appropriate volume.

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au CONTROL LOCATIONS 2 PL-680
  

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au FEATURES FM-stereo/MW/LW/SW/SW SSB/AIR band with high sensitivity, selectivity and user-friendliness FM band coverage: 76 – 108 MHz Shortware Single Side Band (SSB) with upper sideband (USB) and lower sideband (LSB) Equipped with Synchronous Detector and Dual Conversion technology for MW band; this greatly enhances the receiver’s sensitivity, selectivity, imag

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au PL-680 21 If not functioning properly, you can reset the device by sticking a pointed object (such as a straightened paper clip) into the reset hole and gently press the [RESET] button. RESET PROCEDURE 1. When the device is not powered by batteries or the adaptor for a long time, the clock setting is lost, but the stored radio stations are saved. 2. When battery power is low, the » » symbol starts flashing to alert you to charge the batteries or change to new ones. The devic

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au 24 PL-680 SPECIFICATIONS 1. Frequency Range: FM: 76~108 / 87~108 MHz Step: 0.01MHz /0.1 MHz MW: 522~1620 / 520~1710 kHz Tuning Step: 9K for North America or other countries/10K for South America LW: 100~519 kHz Step: 1 kHz/ 9 kHz SW: 1711~29999 kHz Step: 1 kHz/ 5 kHz AIR:118~137MHz Step: 1kHz / 25 kHz 2. Sensitivity FM (S/N=30dB) Less than 3uV MW (S/N

• TECSUN RADIOS AUSTRALIA www.tecsunradios.com.au PL-680 13 1. In POWER OFF mode, press & hold the [POWER] button untill the sleep timer symbol » » flashes on the display. 2. Rotate the [TUNING] knob immediately to select a sleep timer from 1 — 120 minutes or select » » for POWER ON mode (the radio will be turned on after 1 second). Note: The default setting of the sleep timer is «ON «.