Sailor 6120 ssa lrit system инструкция на русском

Related Manuals for COBHAM SAILOR 6120

USER MANUAL

SAILOR 6120/30/40/50 System

Посмотреть товар в Интернет-магазине seacomm.ru

SAILOR 6120/30/40/50 System

User manual

Document number: 98-131590-A

Release date: May 25, 2011

Disclaimer

Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information purposes only, is subject to change without notice and may contain errors or inaccuracies.

Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g. from http://www.thrane.com

or from the distributor .

Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.

Copyright

© 2011 Thrane & Thrane A/S. All rights reserved.

GPL notification

The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. A copy of those licenses is included in this document in the last appendix. You may obtain the complete corresponding source code from us for a period of three years after our last shipment of this product, which will be no earlier than

December 2015, by sending a money order or check for DKK 50 to:

SW Technology/GPL Compliance,

Thrane & Thrane A/S,

Lundtoftegaardsvej 93D

2800 Lyngby

DENMARK

Please write “source for product <product name>” in the memo line of your payment

(replace <product name> with e.g. SAILOR 3027 SSA Terminal).

You may also find a copy of the source at http://www.thrane.com/foss .

This offer is valid to anyone in receipt of this information.

Warranties

Any attempt to install or execute software not supplied by Thrane & Thrane on the devices in this system will result in the warranty being void. Any attempt to modify the software on these devices in a way not specified by Thrane & Thrane will result in the warranty being void.

Trademark Acknowledgements

•

Thrane & Thrane is a registered trademark of Thrane & Thrane A/S in the European

Union and the United States.

•

Inmarsat is a registered trademark of the International Maritime Satellite

Organisation (IMSO) and is licensed by IMSO to Inmarsat Limited and Inmarsat

Ventures plc.

•

SAILOR is a registered trademark of Thrane & Thrane A/S in the European Union, the

United States and other countries.

• Other product and company names mentioned in this manual may be trademarks or trade names of their respective owners.

iv

Safety summary

The following general safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the equipment. Thrane & Thrane assumes no liability for the customer’s failure to comply with these requirements.

Observe marked areas

Under extreme heat conditions do not touch areas of the units that are marked with this symbol, as it may result in injury.

Microwave radiation hazards

During transmission the antenna in this system radiates Microwave

Power.This radiation may be hazardous to humans close to the antenna.

When the system is powered, make sure that nobody gets closer than the recommended minimum safety distance of 0.3 m (1 ft.).

Keep away from live circuits

Operating personnel must not remove equipment covers. Only qualified maintenance personal must make component replacement and internal adjustment. Under certain conditions, dangerous voltages may exist even with the cable removed. To avoid injuries, always disconnect power and discharge circuits before touching them.

Compass safe distance

Minimum safety distance: 5 m from the Mini-C Terminal.

1

About the manual

Naming conventions

This manual covers four different types of system. For information that applies to all four types, the following naming conventions are used:

Common name Used for

2

Mini-C System

Mini-C Terminal

SAILOR 6120 SSA System

SAILOR 6130 LRIT System

SAILOR 6140 Maritime System

SAILOR 6150 Non-SOLAS System

SAILOR 3027 SSA Terminal

SAILOR 3027 LRIT Terminal

SAILOR 3027 Maritime Terminal

SAILOR 3027 Non-SOLAS Terminal

Intended readers

This manual is a user manual for the SAILOR 6120/30/40/50 Mini-C

Systems. The manual is intended for anyone who is using or intends to use any of these four systems. No specific skills are required to operate the SAILOR 6120/30/40/50. However, it is important that you observe all safety requirements listed in the beginning of this manual, and operate the system according to the guidelines in this manual.

v

Manual overview

Note that this manual does not cover installation of the system. For information on installation and initial configuration, refer to

SAILOR 6120/30/40/50 System, Installation manual [1]. Part

numbers for related manuals are listed in the next section.

This manual has the following chapters:

•

Introduction contains an overview of the SAILOR 6120/30/40/50

and a brief description of each unit in the system.

•

Getting started explains how start up the system. It also

contains a short guide to the most important functions.

•

Using easyMail explains how to set up and use the system with

the easyMail application from a connected computer or

SAILOR 6007 Message Terminal.

•

Using Distress and SSA buttons explains how to use connected

Distress buttons and SSA buttons.

•

Troubleshooting contains a short troubleshooting guide and

explains how to check the status of the system.

vi

Related documents

The below list shows the documents related to this manual and to the SAILOR 6120/30/40/50.

Ref Title and description

Document number

[1] SAILOR 6120/30/40/50 System,

Installation manual

[2] SAILOR 6006 and SAILOR 6007

Message Terminal,

Installation manual

98-131589

98-130088

[3] THRANE 6194 Terminal Control Unit,

Installation and user manual

98-131593

Typography

In this manual, typography is used as indicated below:

Bold is used for the following purposes:

• To emphasize words.

Example: “Do not touch the antenna”.

• To indicate what the user should select in the user interface.

Example: “Select SETTINGS > LAN”.

Italic is used to emphasize the paragraph title in cross-references.

Example: “For further information, see Connecting Cables on page…”.

vii

viii

Chapter 1

Chapter 2

Chapter 3

Contents

Introduction

Welcome …………………………………………………………………. 1

System overview ………………………………………………………..2

System units ……………………………………………………………..3

User interface ……………………………………………………………4

The Inmarsat C services ………………………………………………5

Getting started

Registration ……………………………………………………………..9

Starting up the system ……………………………………………… 10

User interfaces ……………………………………………………….. 10

Using easyMail

Overview of easyMail …………………………………………………14

Distress functions (only SAILOR 6150) …………………………..17

Working with messages …………………………………………… 22

Position reporting …………………………………………………… 34

Receiving EGCs ……………………………………………………….36

Network status and settings ………………………………………38

Viewing system details ……………………………………………..40

Viewing or changing position information …………………….41

Viewing status ………………………………………………………… 42

Viewing the Info log ………………………………………………… 42

Setting up the default ISP …………………………………………. 43

ix

x

Contents

Chapter 4

Chapter 5

App. A

App. B

Setting up the default LESes ………………………………………43

Setting up reception of EGCs ……………………………………..44

Setting up ENIDs ……………………………………………………..45

Setting up the Land Earth Stations (LES) ………………………46

Setting up the Inmarsat Service Providers (ISP) …………….48

Entering the mobile number …………………………………….. 50

Setting the local time ……………………………………………….. 51

Setting up password protection ………………………………….52

Setting the language ………………………………………………..52

Setting up PC communication with the Mini-C Terminal …53

Setting up easyMail ………………………………………………….56

Using Distress and SSA buttons

Sending a Distress Alert (SAILOR 6150 only) ……………….. 60

Using SSA buttons (SAILOR 6120 only) …………………………62

Troubleshooting

Getting support ……………………………………………………….63

Updating software ……………………………………………………64

Troubleshooting guide ……………………………………………..66

Status signalling in easyMail ……………………………………..67

Service and repair ………………………………………………….. 68

Conformity

GNU License texts

GNU General Public License ………………………………………75

Glossary

Index

Contents

GNU Lesser General Public License ……………………………. 79

……………………………………………………………………………..85

……………………………………………………………………………..89

xi

Contents xii

Chapter 1

Introduction

Welcome

Congratulations on the purchase of your Mini-C System!

With the Mini-C System you can send and receive data via satellite through the Inmarsat C network. Four variants of the Mini-C System are described in this manual:

• SAILOR 6120 SSA System

• SAILOR 6130 LRIT System

• SAILOR 6140 Maritime System

• SAILOR 6150 Non-SOLAS System

Each of these systems uses its own variant of the

SAILOR 3027 Mini-C Terminal.

This chapter has the following sections:

•

System overview

•

System units

•

User interface

•

The Inmarsat C services

1

1

Chapter 1: Introduction

System overview

The SAILOR 6120/30/40/50 Mini-C System

The Inmarsat C satellite network is the link between the SAILOR 6120/30/40/50 and the destination office. It uses four geostationary satellites to cover the world. For each satellite there is an NCS, Network Coordination Station, handling registration of the mobile unit (in this case the SAILOR 3027) in the

Inmarsat C system.

Each NCS is associated with a number of LESs, Land Earth Stations, which handle the transmission between the mobile units and the destination office.

Satellite

NCS

Network Coordination

Station

LES

Land Earth Station

LES

Land Earth Station

SAILOR 3027

THRANE 6194

2

Internet

Telex

Network

PSDN

Network

PSTN

Network

SAILOR 6007 or computer

Destination office

The SAILOR 3027 can work as a standalone system automatically transmitting data on the Inmarsat C network, or you can connect alarm buttons and/or a

Message Terminal or a computer through the THRANE 6194 Terminal Control

Unit.

System overview

Chapter 1: Introduction

System units

The basic Mini-C System consists of a power supply and the following units:

• SAILOR 3027 Mini-C Terminal.

Contains both transceiver, GPS receiver and omnidirectional antenna for the Inmarsat C system.

Connects to other equipment, primarily the

THRANE 6194, through a CAN interface carrying both power and bi-directional communication.

• THRANE 6194 Terminal Control Unit (only included with SAILOR 6120 and SAILOR 6150).

Enables you to connect the SAILOR 3027 with other equipment, such as Distress buttons, SSA (Ship

Security Alert) buttons or a computer or Message

Terminal. The THRANE 6194 comes with the

SAILOR 6120 and SAILOR 6150 systems only, but is available for the other systems as well.

• SAILOR 6007 Message Terminal (not included. Can be purchased separately).

When the easyMail program is installed, you can send and receive messages, monitor system status and test the system. The SAILOR 6007 has a touchscreen interface but can also be operated from a connected keyboard.

For a more detailed description of the units, refer to the installation manual for the SAILOR 6120/30/40/50 Mini-C System.

System units 3

Chapter 1: Introduction

User interface

The basic Mini-C System does not have a dedicated user interface. To have a user interface you must connect a THRANE 6194 Terminal Control Unit and a computer or SAILOR 6007 Message Terminal with the easyMail application

installed. For details, refer to SAILOR 6120/30/40/50 System, Installation

manual [1].

easyMail

easyMail is a user interface for the Mini-C System. With easyMail you can send and receive messages, view system status and configure the system. To use easyMail you must have a THRANE 6194 Terminal Control Unit and a computer or SAILOR 6007 Message Terminal with the easyMail application installed. For

information on how to get started with easyMail, see easyMail application on page 10.

4

For details on how to use easyMail, see Using easyMail on page 13.

User interface

Chapter 1: Introduction

The Inmarsat C services

The SAILOR 6120/30/40/50 supports the following services through the

Inmarsat C system. For a description of these services, see the next sections.



Distress Alerting



Enhanced Group Call (EGC)



Message transmission



Position reporting



Polling

Distress Alerting and Distress priority messaging

If a ship or a crew is in grave and imminent danger, maritime Inmarsat C and some mini-C models are used to send a Distress Alert by pressing a dedicated

Distress button.

The alert contains information on the ship’s identity (Inmarsat C mobile number), ship’s position (latitude and longitude), ship’s course and speed, nature of Distress, date / time when the alert was sent and time when the ship’s position was last updated.

All Distress Alerts are automatically routed through the addressed LES to an associated Maritime Rescue Coordination Centre (MRCC), which will establish communication with the ship and launch the search and rescue (SAR) operation the ship may need.

After sending the initial Distress Alert, if time permits, it is possible to send a more detailed Distress priority message to give more details about the Distress event and ask for the required assistance.

The Distress priority message should be sent via the same LES as the Distress

Alert, to ensure that it is delivered automatically to the same MRCC.

The Inmarsat C services 5

Chapter 1: Introduction

Enhanced Group Calling (EGC)

The Inmarsat C system has a special capability known as Enhanced Group Call

(EGC), which enables authorised information providers to broadcast messages to selected groups of ships. Reception by ships that are fitted with Inmarsat C or mini-C terminals is automatic. A special header is added by the system to the EGC message to indicate the group of mobile terminals or the geographical area to which the message is to be sent.

Two EGC services are available:

• EGC SafetyNET — the international safety service, which allows authorised maritime safety information (MSI) providers, such as meteorological offices, hydrographic officers and MRCCs to broadcast messages to all ships in certain geographical areas.

MSI includes navigational and meteorological warnings, meteorological forecasts and other urgent safety-related information, which is addressed to all ships in NAVAREA / METAREA, user-defined circular or rectangular area or coastal area.

Reception of SafetyNET messages is a mandatory function of the GMDSS equipment that is required to be carried in certain ships under the provision of the International Maritime Organisation’s Safety Of Life At Sea

(SOLAS) convention.

• EGC FleetNET — the international commercial service, which allows authorised information providers, such as commercial subscription services, shipping companies or governments to broadcast messages to selected groups of vessels, each of which has registered with the information provider and been added to a FleetNET closed group / network. The mobile terminals on these groups of vessels are identified by an ENID (EGC Network IDentification) common to the group.

For further information on EGC via Inmarsat C read the Inmarsat Maritime

Communications Handbook, Chapter 6, or visit the Inmarsat Maritime

Safety Services section of the Inmarsat website www.inmarsat.com

.

6 The Inmarsat C services

Chapter 1: Introduction

Message transmission

Ship to shore: Text and data from Inmarsat C and mini-C terminals can be sent

to:

• An e-mail address

• Any telex or fax (text, one way only) number

• Any computer connected to the public telephone and data networks (PSTN and PSDN), using a telephone modem number

• Another Inmarsat C / mini-C terminal

• A Short (or Special) Access Code (SAC).

The maximum message size is up to 10 kb for the Mini-C Terminal.

Shore to ship: Text and data can be sent via telex, e-mail and the data and

telephone (PSDN / PSTN) networks. To be able to send messages to ships, a shore-based message originator needs to be registered (to have a commercial service agreement) with an Inmarsat C service provider of their choice.

Ship to ship: Messages can also be sent in a ship-to-ship direction from one

Inmarsat C / mini-C terminal to another.

Position reporting

Most of Inmarsat C and mini-C models are integrated with Global Navigational

Satellite System (GNSS) receivers, such as GPS, to provide highly reliable, round-the-clock position information of a ship, which can be used for position reporting.

The position reporting service is based on using the data reporting and polling protocol and allows a shore-based subscriber (base station or shipping company) to request position information from a vessel, as a single report or automatic reception at fixed intervals, e.g. every six hours.

A ship’s terminal can also be programmed to send regular position reports to any desired destination.

The position report includes ship’s identity, latitude, longitude, course, speed, date / time of the position report and time of the last position update.

The Inmarsat C services 7

Chapter 1: Introduction

In the Mini-C System, the report is sent to a DNID (Data reporting Network

IDentification) that is effectively a mailbox created on some LESes. The

Mini-C Terminal sends its reports to this mailbox and other tracking systems can then access and empty the mailbox.

Up to 255 mobile terminals can use the same DNID, and the specific terminal is identified by a member number between 1 and 255.

Before the position reporting feature can be used the DNID must be created on the LES. Once the DNID account is created, the LES can download the DNID information to the desired terminals, thereby enabling them to send reports to the DNID.

Data reporting and polling

Inmarsat C users may need to acquire information (short data reports) from vessels, or to collect data automatically at fixed or variable intervals.

The data reporting service allows for the transmission of information, in packets of up to 32 bytes on request or at prearranged intervals from Inmarsat

C or mini-C terminals, to shore-based customers.

Polling allows shore-based customers to interrogate an Inmarsat C or mini-C terminal or group of terminals by sending a special polling command. The polling command instructs a terminal or group of terminals to send a data report immediately, start sending regular reports, change transmission schedule of reports or perform another task of the polled terminal(s).

8 The Inmarsat C services

Chapter 2

Getting started

This chapter explains how to start up and log on your SAILOR 6120/30/40/50. It has the following sections:

•

Registration

•

Starting up the system

•

User interfaces

Registration

Before using the SAILOR 3027 Mini-C Terminal on the Inmarsat-C system you must register the terminal to the system. In most cases the distributor has already filled in the SARF (Service Activation Registration Form) for your

SAILOR 3027 when you receive your SAILOR 6120/30/40/50 Mini-C System.

For details on registration, see the Installation manual for the SAILOR

6120/30/40/50 Mini-C System.

After registration you must use a Message Terminal or a computer with the easyMail application to set up the mobile number in the SAILOR 3027. See

Using easyMail on page 13.

2

9

Chapter 2: Getting started

Starting up the system

When the power source is on, the SAILOR 3027 automatically starts up and logs on to the satellite network.

With the Message terminal or a computer with easyMail installed you can see the logon status on screen.

User interfaces

If you are going to use your Mini-C System for anything other than automatically transmitting reports, you should have a user interface for accessing the Mini-C System. In Non-SOLAS Distress systems a user interface is mandatory, because of the need for safety communication.

You can control the Mini-C System using the easyMail application installed on a computer or on a SAILOR 6007 Message Terminal. The computer or the

SAILOR 6007 Message Terminal must be connected via the LAN interface in the THRANE 6194 Terminal Control Unit to the Mini-C System.

For SAILOR 6150 systems only, you may also use a SAILOR 6006 Message

Terminal. The SAILOR 6006 Message Terminal connects directly to the CAN interface.

easyMail application

Installing easyMail

To install the easyMail application on your computer, do as follows:

1. Insert the installation CD supplied with the THRANE 6194 into the CD drive of the computer.

The setup program should start up automatically. If not, run the file setup.exe from the CD drive.

2. Click Install easyMail and go through the InstallShield Wizard.

10 Starting up the system

Chapter 2: Getting started

3. When the Wizard is complete, you can start the application from the easyMail shortcut on the desktop, or from Start > Programs > easyMail

<version>.

Accessing your Mini-C Terminal with easyMail

1. Acquire a THRANE 6194 Terminal Control Unit, if it is not already part of your system.

2. Connect your Mini-C Terminal to the CAN interface on the THRANE 6194

Terminal Control Unit.

3. Connect a computer to the RS-232 port or the LAN port of the THRANE 6194

Terminal Control Unit.

Refer to THRANE 6194 Terminal Control Unit, Installation and user manual

[3] for information on how to connect and set up the interfaces.

4. Start the application from the easyMail shortcut on the desktop, or from

Start > Programs > Thrane & Thrane > easyMail <version>.

5. If the PC connection is not already set up

(the PC connection bar is red), see Setting

up PC communication with the

Mini-C Terminal on page 53.

When all three bars are green, you can use the easyMail application to set up

and control the Mini-C System, send and receive messages etc. See Using

easyMail on page 13.

User interfaces 11

Chapter 2: Getting started

SAILOR 6006 Message Terminal (SAILOR 6150 only)

To get started with the SAILOR 6006 Message Terminal, do as follows:

1. Acquire a SAILOR 6006 Message Terminal from Thrane & Thrane.

2. Connect the THRANE 6194 to the Mini-C System

as described in SAILOR

6120/30/40/50 System, Installation manual [1].

3. Connect the Message Terminal to the CAN interface (T-connector) in the

Mini-C System. See SAILOR 6120/30/40/50 System, Installation manual [1].

You can now use the Message Terminal to set up and control the Mini-C

System, send and receive messages etc.

12 User interfaces

Chapter 3

Using easyMail

This chapter describes how to operate the SAILOR 6120/30/40/50 using the easyMail application. It has the following sections:

•

Overview of easyMail

•

Distress functions (only SAILOR 6150)

•

Working with messages

•

Position reporting

•

Receiving EGCs

•

Network status and settings

•

Viewing system details

•

Viewing or changing position information

•

Viewing status

•

Viewing the Info log

•

Setting up the default ISP

•

Setting up the default LESes

•

Setting up reception of EGCs

•

Setting up ENIDs

•

Setting up the Land Earth Stations (LES)

•

Setting up the Inmarsat Service Providers (ISP)

•

Entering the mobile number

•

Setting the local time

•

Setting up password protection

•

Setting the language

•

Setting up PC communication with the Mini-C Terminal

•

Setting up easyMail

3

13

Chapter 3: Using easyMail

Overview of easyMail

For information on how to install and start up easyMail, see easyMail

application on page 10.

Overview of the screen

Below is an overview of the main screen in easyMail.

Mobile status Connection status Menu bar

Message header

Contents

14

Shortcut buttons

•

The menu bar holds the menus. For an overview of all menus, see Menu

overview on page 16

Overview of easyMail

Chapter 3: Using easyMail

•

Mobile status shows the status of your Mini-C Terminal. When connected

and logged in, this field shows the mobile number (MMI) and the ocean region to which your Mini-C Terminal is logged in.

•

Connection status shows the status of your PC connection, your mini-C

antenna connection and your GPS connection.

•

Message header contains the fields where you can enter recipients and

subject for a message.

•

Shortcut buttons may be used for quick access to some of the menu items.

You can show/hide the shortcut buttons under View > Compact mode.

•

Contents. Depending on the selected view, this area can show your

message text or e.g. received messages or EGCs.

Overview of easyMail 15

Chapter 3: Using easyMail

Menu overview

File

Edit

View

Messaging

Distress

*

Setup

Actions

Help

New

Open

Save

Merge

Print Editor

Exit

Cut

Copy

Paste

Text Size

Insert

Define signature

Enter Vessel data

Editor

Distress message editor *

Inbox

Outbox

EGC

Info Log

Transceiver status

GPS status

Position info

Terminal mode **

Compact mode

New message

Contacts/Address book

Default messages

Position reporting

Send message

Distress alert setup

Reset alarm/latest Distress info

Distress test mode

Test easyMail sound

Default ISP

Default LES

EGCs

DNIDs

ENIDs

Land Earth Stations (LES)

Inmarsat Service Providers (ISP)

Mobile number (IMN)

Local time zone/PC time

Passwords

Language

Communication setup

Settings

* Only for SAILOR 6150

** Only described in

SAILOR 6120/30/40/50 installation manual

Position

Speed and course

Signature

Mobile number

UTC date and time

Local date and time

Vessel name

Vessel data

Set up function keys

F1 [Empty]

F2 [Empty]

F3 [Empty]

F4 [Empty]

F5 [Empty]

F6 [Empty]

F7 [Empty]

F8 [Empty]

Transmit password

Config password

Remote config password

Messages

Electronic forms

Misc

Login

Logout

Preferred ocean

Link test

Abort transmission

System info

About easyMail

[581] East Atlantic (AOR-E)

[582] Pacific (POR )

[583] Indian (IOR)

[584] West Atlantic (AOR-W)

Scan preferred ocean

Set preferred ocean

[581] East Atlantic (AOR-E)

[582] Pacific (POR)

[583] Indian (IOR)

[584] West Atlantic (AOR-W)

None

16 Overview of easyMail

Chapter 3: Using easyMail

Distress functions (only SAILOR 6150)

Writing a Distress priority message (only SAILOR 6150)

Note

Distress priority messages are sent to the MRCC only.

Distress priority messages must be written in English.

To write a Distress priority message, do as follows:

1. From the menu bar, select View > Distress message editor.

A warning appears.

2. Click Yes and then OK to continue to the Distress message editor.

The position and mobile number of your Mini-C Terminal is automatically inserted at the beginning of the Distress message, together with the data you have entered under Vessel data (if any).

3. Type a subject for the message.

Important

The Subject field is important — some messages may not be received correctly if the subject is missing.

4. Type your message, describing the nature of the Distress.

5. Click Send.

Setting up Distress alert

You can temporarily change the settings for your Distress function.

For information on how to use the Distress button to send a Distress alert, see

Sending a Distress Alert (SAILOR 6150 only) on page 60.

Default settings:

• Distress Alert Nature: Unspecified.

• Distress Alert Land Earth Stations: LES automatically selected by mobile.

(the SAILOR 3027 selects the LES with the best signal).

Distress functions (only SAILOR 6150) 17

Chapter 3: Using easyMail

• Distress Alert Position, Course and Speed: Always use latest position from

GPS.

Note

The Distress Alert Nature and the Distress Alert Position, Course and

Speed settings are only valid for the current Distress Alert or maximum one hour. Then these settings are returned to the default settings. The entered Distress LESs remain in the system.

To change the Distress alert settings, do as follows:

1. From the menu bar, select Distress > Distress alert setup.

2. Click OK after reading the warning popup window.

18 Distress functions (only SAILOR 6150)

Chapter 3: Using easyMail

3. From the drop-down list at each ocean region, select the LES to be used for

Distress alerts or leave the setting at LES automatically selected by mobile

(default setting).

4. If necessary, change the position, course and speed.

Note

Do not change the default setting unless you have good reasons to do so. The default setting is “Always use latest position from

GPS”. It is normally best to show your current GPS position when sending a Distress Alert.

You may need to change the position, e.g. if the person(s) that need help are no longer on board the ship (man overboard).

5. Select the nature of the Distress.

6. Click OK.

Reset alarm/latest Distress info

After sending a Distress alert or receiving an urgent/distress priority EGC or message, you can reset the alarm light and sound in the alarm buttons. At the same time you can see status on Distress alerts and Distress test. Do as follows:

1. Select Distress > Reset alarm/latest Distress info.

A popup window shows information on the latest Distress Alert and the latest Distress test.

2. Click OK.

The light and sound in the alarm button(s) are switched off.

Distress functions (only SAILOR 6150) 19

Chapter 3: Using easyMail

Testing Distress buttons

Important

Never test the installation by sending an alert on-air!

If an alert is sent by mistake, inform the relevant authorities immediately.

You can test the Distress button(s) in your system without sending a real

Distress alert. Do as follows:

1. Select Distress > Distress test mode.

2. When you see the Distress test mode window shown above, press the connected Distress button(s) as you would in a real Distress situation.

The light and buzzer in the Distress buttons should work the same way as

in a real Distress situation. For details on the Distress buttons, see Sending

a Distress Alert (SAILOR 6150 only) on page 60.

3. To clear alarm indications, select Distress > Reset alarms/latest Distress

info.

The button light should go off.

4. Click Cancel to exit Distress test mode.

Note

The system automatically exits the test mode after 15 minutes, if you do not Cancel it.

20 Distress functions (only SAILOR 6150)

Chapter 3: Using easyMail

Testing easyMail alarm sound

To test the alarm sound in easyMail, do as follows:

1. Select Distress > Test easyMail sound.

2. Click Start to hear the sound on your computer.

Your computer will now play the same sound that you will hear when a

Distress alert is sent or an urgent/distress priority EGC or message is received.

3. Click Stop to stop the sound.

4. When you have finished testing, click Cancel or close the window.

Distress functions (only SAILOR 6150) 21

Chapter 3: Using easyMail

Working with messages

Preparing the system

Before you can send a message:

• The recipient of the message must be listed in the Address book. For

details, see Managing the list of Contacts on page 30.

• The Mini-C Terminal must be logged in to an Ocean Region.

Normally the Mini-C Terminal logs in automatically. If it is logged out, see

Logging into and out of the network on page 38.

• The default ISP must be set.

See Setting up the default ISP on page 43.

• Default LESes must be set for all Ocean Regions.

See Setting up the default LESes on page 43.

• The mobile number must be configured in the Mini-C Terminal.

This is normally set up during installation. If not, see Entering the mobile

number on page 50.

22 Working with messages

Chapter 3: Using easyMail

Writing a routine priority message

To write a routine priority message, do as follows:

1. If the editor is not already open, select File > New or click the Editor button to the left (if present).

2. Select To… in the top left corner and select the recipient(s) of the message from the Address book.

Alternatively you may type in the recipient manually.

3. In the Subject field, type in a subject title for your message.

Important

The Subject field is important — some messages may not be received correctly if the subject is missing.

4. If you want to send a data file instead of typing text in the text editor, skip

the next step and go directly to step 6.

5. Type your message text in the editor.

Working with messages 23

Chapter 3: Using easyMail

For information on how to edit text, see Editing your message on page 25.

Note

If you want to save your message without sending it, you can save it as a file by selecting File > Save.

6. When the message is ready to be sent, click Send.

24

7. Select what you want to send.

• If you want to send a data file, select File from disk, browse to the file you want to send and click Open.

• If you want to send the text in the editor, select Text in editor.

8. Select if you want:

• Confirmation request

• Print message upon sending

9. Select OK.

The message is sent as soon as the network allows it. You can see the status of your message under View > Outbox.

Working with messages

Chapter 3: Using easyMail

Options for writing and sending messages

In the File menu, you have the following options:

•

New. Opens a new message.

•

Open. Allows you to select a text file to be opened in the editor.

•

Save. Allows you to save the message for later use.

•

Merge. Allows you to insert the contents from a text file into your message

at the cursor position.

•

Print editor. Prints the message on a connected printer.

•

Exit. Closes easyMail.

Editing your message

When writing a message you have some editing options, described in the next subsections.

To cut, copy and paste

In the Edit menu you can select Cut, Copy and Paste as in a normal editor.

To change text size

To change the text size, press Ctrl+F1 (smaller) and Ctrl+F2 (larger), or select

Edit > Text size > + Ctrl+F2 or — Ctrl+F1.

Working with messages 25

Chapter 3: Using easyMail

To insert information automatically

To insert information such as position and vessel data in your message, do as follows:

1. Select Edit > Insert.

2. Select the information you want to insert.

Note

Signature and vessel data must first be defined. See the next section.

The information is now inserted in your message as part of the message text.

26 Working with messages

Chapter 3: Using easyMail

To enter signature and vessel data

You can enter a signature and your vessel data for later automatic insertion in your messages (see previous section). To define your signature, do as follows:

1. Select Edit > Define signature.

2. Type in your signature and click OK.

The signature is now saved for later use with Edit > Insert.

To enter your vessel data, do as follows:

1. Select Edit > Enter vessel data.

2. Fill in the vessel data for your ship and click OK.

Working with messages 27

Chapter 3: Using easyMail

Using default messages

You can write a default message that you can recall and send by pressing one of the F-keys F1 to F8.

Creating a default message

To create a default message, do as follows:

1. Open the message editor.

2. Type in your message.

3. Select Messaging > Default messages.

4. Select the F-key you want to use for the message.

5. Type a name for the message.

6. Click Save and close.

Sending a default message

To recall and send the message, fill in the message recipient and a subject in the editor To… field and press the F-key you selected above.

Important

The Subject field is important — some messages may not be received correctly if the subject is missing.

28 Working with messages

Viewing messages in the Inbox

To view the messages in the Inbox, do as follows:

1. Select View > Inbox.

Chapter 3: Using easyMail

2. Double-click the message you want to read.

From within the message you have the following options:

•

Print. The message is printed on the connected printer.

•

Save. You can browse to a location and save the message (.txt file)

•

Forward. The message text is inserted into the editor so you can

forward it to a new recipient.

•

Wrap text. When selected, the text is wrapped to fit the window size.

3. Click OK or Cancel to close the message.

4. To delete one or more messages, right-click the message(s) and select

Delete message)

Working with messages 29

Chapter 3: Using easyMail

Viewing sent messages (Outbox)

After writing a message and selecting Send, you can see the message and the status of the message in the Outbox

To view messages in the Outbox, select View > Outbox.

Managing the list of Contacts

To manage your list of contacts, click

Contacts/Address book.

or select Messaging >

30

To see details for a contact, select it and click Properties.

Working with messages

Chapter 3: Using easyMail

To add a new contact

Do as follows:

1. In the Address book, select New at the bottom of the page.

2. Type in the name of your contact.

3. Select the address type below the name.

4. Type in the details for your contact. The format of the address/number depends on the selected address type. See the table on the next page.

5. Select OK.

The new contact is now listed in the Address book.

Working with messages 31

Chapter 3: Using easyMail

Message formats and presentation:

Type Format of number Example Presentation

E-mail

Telex

Standard e-mail address [email protected]

5, 7 or 8 bit

Country code + subscriber no.

0045 99999999 5 or 7 bit

Fax

Inmarsat-C mobile

Country code + subscriber no.

0045 99999999

Mobile number 492388999

Country code + subscriber no.

0045 99999999

5, 7 or 8 bit

5, 7 or 8 bit

5, 7 or 8 bit PSTN modem

Special access code

5, 7 or 8 bit

X.25

Pre-defined codes:

• 32 — Medical Advice

• 33 — Technical Assistance

• 38 — Medical Assistance

• 39 — Maritime Assistance

• 41 — Meteorological

Reports

• 42 — Navigational Hazards and Warnings

• 43 — Ship Position and Sail

Plan Reports

32

DNIC (country code) + subscriber no.

2380 99999999 5, 7 or 8 bit

32 Working with messages

Chapter 3: Using easyMail

To edit a contact

Do as follows:

1. In the Address book, select the contact.

2. Select Properties.

3. Edit the details.

See the previous section for information on the contact details.

4. Select OK.

To delete a contact

Do as follows:

1. In the Address book, select the contact.

2. Select Delete.

3. Select Yes to confirm.

4. Select OK to leave the Address book.

Working with messages 33

Chapter 3: Using easyMail

Position reporting

For general information on the position reporting service, see Position

reporting on page 7.

Note

To be able to use the position reporting feature, a DNID must be

downloaded and enabled in the Mini-C Terminal. See Setting up

ENIDs on page 45.

To access the PU reporting setup page, Select:

Messaging > Position reporting.

The PU (Position Unreserved) reporting setup window shows the position reporting programs for the Mini-C Terminal. For each program you can see the status and whether it is a local or remote program.

34 Position reporting

Chapter 3: Using easyMail

To start a local position reporting program

Note

Only local position reporting programs can be managed locally. You can see the remotely configured programs as well but you cannot change them.

To start a program that is already defined, do as follows:

1. From the PU Reporting Setup page, click the Start button at the program you want to start. The Start button becomes a Stop button .

The Mini-C Terminal will now start sending position reports from the defined start time with the defined intervals until you stop it with the Stop button.

2. Click OK.

To define a new position reporting program

To define a new local program, do as follows:

1. From the PU Reporting Setup page, select New.

Position reporting 35

Chapter 3: Using easyMail

2. Select the DNID information (provider, LES, DNID and member number) for each ocean region.

3. Select the time to start the position reporting or select Immediately.

4. Select the interval between the position reports.

5. Click OK.

The program is now set up and you can start and stop it with the buttons as described in the previous section.

6. Click OK again to exit the PU Reporting Setup page.

Receiving EGCs

Viewing incoming EGCs

You can receive various types of EGCs in easyMail. For details about how to set up which EGCs to receive, see

Setting up reception of EGCs on page 44.

Note

To be able to receive FleetNET EGCs, an ENID must be downloaded

and enabled in the Mini-C Terminal. See Setting up ENIDs on page 45.

Note

When the EGC Inbox is full, the oldest EGCs are automatically deleted.

36 Receiving EGCs

To view EGCs, do as follows:

1. Select View > EGC from the main menu.

Chapter 3: Using easyMail

2. Double-click an EGC to see the contents.

From within the EGC you have the following options:

•

Print. The EGC is printed on the connected printer.

•

Save. You can browse to a location and save the EGC (.txt file)

•

Forward. The EGC text is inserted into the message editor so you can

forward it to a new recipient.

•

Wrap text. When selected, the text is wrapped to fit the window size.

3. Click OK or Cancel to close the EGC.

4. To delete one or more EGCs, right-click the EGC(s) and select Delete EGC.

Receiving EGCs 37

Chapter 3: Using easyMail

Network status and settings

The Mobile status field at the top of the page shows the status of the network connection. When the Mini-C Terminal is logged in to the network, this field shows the ocean region to which the Mini-C Terminal is logged in.

Logging into and out of the network

To log into the Inmarsat C network, select Actions > Login and select the Ocean

region you are logging into.

If you want to use the preferred ocean configured in the Mini-C Terminal, or simply the region with the best signal, use Scan preferred ocean instead (see the next section).

To log out of the network, select Actions > Logout.

Scanning the network

If you want the system to find the best signal, select Actions > Preferred ocean

> Scan preferred ocean. The system will then scan for the best signal and log in.

If an ocean region is selected under Set preferred ocean, the system will scan the selected ocean first.

Setting the preferred ocean region

If you want the system to generally use a specific ocean region, select Actions

> Preferred ocean > Set preferred ocean and select the ocean region you want to use. If you select None, the scanning process will use the ocean region with the best signal.

38 Network status and settings

Chapter 3: Using easyMail

The selected ocean region is used when you select Actions > Preferred ocean

> Scan.

Link test

Note

To test basic system connectivity, we recommend that you send a short message to yourself instead of using the link test. For details

on how to send a message, see Writing a routine priority message on page 23.

If you still want to make a link test, do as follows:

1. In the easyMail application, click Actions > Link test.

After the Link test is requested, the NCS assigns a LES for performing the

Link test. This can take a while.

2. When the Linktest window appears, click Execute to start the test.

Note

Because the link test has low priority in the network it can take a long time for the system to complete the link test, and during this time the system has limited functionality.

A popup window informs you that the test has started. When the test has ended another popup window informs you that the test was completed successfully or that it failed.

Stop Transmission

If you want the system to immediately stop transmitting, select Actions > Abort

transmission.

The current protocol is then cleared, and any ongoing transmission is stopped.

Network status and settings 39

Chapter 3: Using easyMail

Viewing system details

To see information on easyMail and the Mini-C Terminal, click

Help > System info.

or select

40 Viewing system details

Chapter 3: Using easyMail

Viewing or changing position information

To view or change your current position information, course and speed, do as follows:

1. select View > Position info.

2. If there is no synchronization with the positioning system, you can enter a manual position, course and speed.

3. Select OK.

The manually entered position data will be used by the system until the automatic position data is available again.

Viewing or changing position information 41

Chapter 3: Using easyMail

Viewing status

To see the status of the Mini-C Terminal, select View > Transceiver status, or click the Antenna signal bar in the connections status field at the top of the page.

To see the GPS status, select View > GPS status, or click the GPS bar in the connections status field at the top of the page.

Connection status field

Viewing the Info log

To see the information log, select View > Info log.

The information log shows the most recent events registered in your Mini-C

System.

42 Viewing status

Chapter 3: Using easyMail

Setting up the default ISP

To set up a default ISP, do as follows:

1. Select Setup > Default ISP.

2. Select the default ISP from the list.

3. Select Set Default LESs to ISP settings if you want to use the default ISP with the Default LESes.

4. Click OK.

Setting up the default LESes

To set up the default LESes, do as follows:

1. Select Setup > Default LES.

2. Select the default LES for each ocean region.

3. Click OK.

Setting up the default ISP 43

Chapter 3: Using easyMail

Setting up reception of EGCs

For general information on EGCs, see Enhanced Group Calling (EGC) on page 6.

To set up reception of EGCs, do as follows:

1. Select Setup > EGCs.

44

2. To set up the additional areas from which you want to receive meteorological or navigational EGCs, select Additional NAVAREA(s)

/METAREA(s).

Then select the numbers of the areas from which you want to receive EGCs, and select OK.

Note

You always receive EGCs from the area in which you are located.

The areas selected here are additional areas.

Setting up reception of EGCs

Chapter 3: Using easyMail

3. Select whether you want to receive System Messages or SafetyNET messages or both.

4. To change the Coastal Warning Areas, type in the new areas under Coastal

Warning Areas [A..Z].

5. Select the types of EGC service you want to receive.

6. If you want to receive EGCs at specific positions on your route, select Fixed

positions and fill in the position information for each point on the route.

7. Click OK.

Setting up ENIDs

ENIDs (EGC Network IDentification) are used for identifying the

Mini-C Terminal on the network in order for the terminal to receive FleetNET

EGCs.

ENIDs must be set up with your LES operator and downloaded to your

Mini-C Terminal before you can use them.

To set up the ENIDs, do as follows:

1. Select Setup > ENIDs.

The ENIDs are listed with provider, ENID and status.

2. Select the ENIDs you want to enable.

3. Click OK.

Setting up ENIDs 45

Chapter 3: Using easyMail

Setting up the Land Earth Stations (LES)

To view or edit the list of Land Earth Stations for each ocean region, do as follows:

1. Select Setup > Land Earth Stations (LES).

2. Select a LES and click Edit.

46

3. If necessary, type in the new name of the LES.

4. Click OK.

5. To use default LES numbers and names for an ocean region, click the

Default button and click Yes.

6. Click OK to exit.

Setting up the Land Earth Stations (LES)

Chapter 3: Using easyMail

List of currently supported LESs

The table below shows the LESs supported by the service providers at the time of writing. Note that the list is dynamic, so it may not be completely up to date.

Service Provider

CTTC China

KDDI SatMail-C Japan

Morsviazsputnik Russia

OTE Greece

SingTel Mail65 (SAC65)

SingTel Mail65 (SAC6500)

SingTel Mail65 (SAC6599)

Stratos Global C-email 02

Stratos Global C-email 12

Telemar X.25

Vizada SkyFile C 01

Vizada SkyFile C 04

Vizada SkyFile C 21

002

012

004

001

—

002

002

002

—

003

—

LES no.

AOR-W

LES no.

AOR-E

LES no.

POR

211

004

021

—

103

117

120

102

102

102

102

112

104

101

104

121

203

—

—

210

210

210

202

212

204

201

204

221

303

317

305

328

LES no.

IOR

311

304

301

304

321

328

328

302

312

Setting up the Land Earth Stations (LES) 47

Chapter 3: Using easyMail

Setting up the Inmarsat Service Providers (ISP)

Note

Do not change these settings unless you know the exact formats to enter.

The Inmarsat Service Providers are already set up when you receive your system. However, if an Inmarsat Service Provider e.g. changes the format for email, you can change these settings to match the new format.

To set up the Inmarsat Service Providers in the Mini-C Terminal, do as follows:

1. Select Setup > Inmarsat Service Providers (ISP).

48

2. To edit the information for a provider, select the provider from the list and fill in the new information as specified from the provider.

3. Click OK.

Setting up the Inmarsat Service Providers (ISP)

Chapter 3: Using easyMail

To add a new provider

To add a new provider to the list, do as follows:

1. In the Inmarsat service providers window, click New provider.

2. Type the name of the provider in the top left corner and click Add.

The new provider is now added to the list, but without any information.

3. Fill in the information for the provider.

4. Click OK.

Setting up the Inmarsat Service Providers (ISP) 49

Chapter 3: Using easyMail

Entering the mobile number

Before you can use the Mini-C Terminal on the Inmarsat C network you must configure the mobile number from your service provider in the

Mini-C Terminal.

To enter the mobile number, do as follows:

1. Select Setup > Mobile number (IMN).

2. Type in the mobile number from your service provider.

3. Click OK.

The number is now stored in the Mini-C Terminal and can be used to access the Mini-C Terminal on the Inmarsat C network.

50 Entering the mobile number

Chapter 3: Using easyMail

Setting the local time

The Mini-C Terminal gets the UTC time from the GPS receiver. You can convert this time to local time and set the time on your computer accordingly.

Do as follows:

1. Select Setup > Local time zone/PC time.

2. Use the up/down arrows to set the time difference between your local time and UTC time.

3. At the bottom of the window, select one of the following:

•

Yes. The PC time is automatically updated at startup

•

No. The PC time will not be updated.

•

Ask. You will be asked at startup whether you want to update the PC

time or not.

4. Click OK.

Setting the local time 51

Chapter 3: Using easyMail

Setting up password protection

You can add password protection to three different actions: Transmission, configuration and remote configuration.

To add password protection, do as follows:

1. Select Setup > Passwords.

2. Select the password you want to add or change.

3. Type in the old password (leave empty if there was no password protection).

4. Type in the new password under New password and again under Confirm

password.

5. Click OK and close easyMail.

With the password protection, easyMail will ask for a password when a person tries to access the password protected areas (transmit a message, configure the system or configure the system remotely).

To remove the password, repeat the above procedure and leave the fields with the new password empty.

Setting the language

To change the language in easyMail, do as follows:

1. Select Setup > Language.

2. Select the language you want in easyMail.

3. Select at the bottom whether you want to show the language selection at startup.

4. Click OK.

52 Setting up password protection

Chapter 3: Using easyMail

Setting up PC communication with the

Mini-C Terminal

To connect a computer to the system you must use a THRANE 6194 Terminal

Control Unit. You can connect the computer to the LAN interface or the RS-232 interface on the THRANE 6194.

Note

The Communication setup is not accessible when the computer has established a connection with the Mini-C Terminal.

To set up LAN communication

To set up easyMail for LAN communication with the THRANE 6194 and thereby the Mini-C Terminal, do as follows:

1. Select Setup > Communication setup.

2. Select LAN communication.

Same subnet

3. Type in the IP address of the THRANE 6194 Terminal Control Unit (TCU).

You can find the IP address in two ways:

Setting up PC communication with the Mini-C Terminal 53

Chapter 3: Using easyMail

• Using the SNMP upload program, described in Updating software on page 63.

• By pressing the Temporary fixed IP address button on the

THRANE 6194. The IP address of the THRANE 6194 is temporarily set to

169.254.100.100.

Your IP: Shows the IP address of your PC. Make sure your PC is on the

same subnet as the TCU! This means the two first sections of the IP address

(10.6. in the example picture above) must be the same on the TCU as on your PC.

4. If you want to set the THRANE 6194 to a fixed IP address for your next easyMail session, select Force fixed IP and type in the IP address you want to use.

Important

Before clicking OK, make sure the IP address of your PC is on the same subnet as the new TCU IP address.

5. Click OK.

easyMail now tries to establish a connection to the THRANE 6194 and thereby the Mini-C Terminal. When the LAN connection is established the

PC connection bar at the top of the easyMail window turns green.

54 Setting up PC communication with the Mini-C Terminal

Chapter 3: Using easyMail

To set up RS-232 communication

To set up easyMail for RS-232 communication with the THRANE 6194 and thereby the Mini-C Terminal, do as follows:

1. Select Setup > Communication setup.

2. Select Serial communication.

3. Select the COM port you are using on your computer and the Baud rate of the THRANE 6194 (default is 115200).

4. Click OK.

easyMail now tries to establish a connection to the THRANE 6194 and thereby the Mini-C Terminal. When the RS-232 connection is established the PC connection bar at the top of the easyMail window turns green.

Setting up PC communication with the Mini-C Terminal 55

Chapter 3: Using easyMail

Setting up easyMail

To change message setup

You can set up some general settings for messages in the Messages tab. Do as follows:

1. Select Setup > Settings.

2. Select the Messages tab.

56

3. If you want to get an info box when a new message has arrived, select

Show info box when new message is received.

4. If you want to allow configuration of easyMail from a remote location, select Allow easyMail Remote Configuration.

Selecting this option enables an authorised remote user to configure certain parts of easyMail using a special kind of message sent to your

Mini-C System.

5. If you have a printer connected, select the message types you want to print automatically (if any).

Setting up easyMail

Chapter 3: Using easyMail

To use electronic forms

Some users have a need for a specific layout, e.g. for fishery catch reporting.

The files for this layout must be downloaded to the system before selecting the formats on this page.

Miscellaneous settings

In Harbour Button

Select Setup > Settings > Misc > In Harbour Button to select whether or not you want to show an In Harbour Button in easyMail. The In Harbour button is used for setting a longer reporting interval when the ship is in harbour.

Reset HotList

The HotList is a list of the last used commands on the Mini-C Terminal. To see the list, press F12.

To reset the HotList, select Setup > Settings > Misc > Reset HotList.

Setting up easyMail 57

Chapter 3: Using easyMail

58 Setting up easyMail

Chapter 4

Using Distress and SSA buttons

4

This chapter describes how to use the 6108 Non-SOLAS Alarm Panel and the

SSA buttons. It has the following sections:

•

Sending a Distress Alert (SAILOR 6150 only)

•

Using SSA buttons (SAILOR 6120 only)

59

Chapter 4: Using Distress and SSA buttons

Sending a Distress Alert (SAILOR 6150 only)

Important

Only send a Distress Alert if you are in immediate danger!

The Distress Alert can be compared to a MAYDAY call.

With the SAILOR 6150 system you may have a SAILOR 6108 Non-SOLAS Alarm

Panel installed.

To send a Distress Alert, do as follows:

1. Open the cover for the Distress button.

2. Press and hold the button until the light is steady and the buzzer stops (more than 5 seconds).

During this time the button light flashes and the buzzer sounds. After 5 seconds the red light goes steady on and the buzzer is silent.

When the Distress alert is acknowledged, the button light goes off shortly every 15 seconds.

You must have either a Message Terminal or a computer with easyMail in a

SAILOR 6150 system. Use the Message Terminal or easyMail to see the status

of the Distress and to follow up. See Distress functions (only SAILOR 6150) on page 17.

Important

The MRCC normally sends a message to the alerting unit to gather more information about the situation.

If possible, respond to such messages with a Distress message sent to the same LES that was used for the Distress Alert.

For information on how to send a Distress message, see Writing a Distress

priority message (only SAILOR 6150) on page 17.

The MRCC may also send Distress EGCs to other ships in the area to request assistance (typically as Distress Relay or SAR Coordination request).

See also Setting up Distress alert on page 17.

60 Sending a Distress Alert (SAILOR 6150 only)

Chapter 4: Using Distress and SSA buttons

Clearing distress indications

Note

This function will only turn off the visual and audible indications on board. It will not cancel the transmission of the Distress Alert.

If you want to turn off all distress indications while a Distress Alert is still active, you can use one of the following:

•

Message Terminal: Select Distress > Status > Clear distress indications.

•

easyMail: Select Distress > Reset alarm/Latest Distress info.

Sending a Distress Alert (SAILOR 6150 only) 61

Chapter 4: Using Distress and SSA buttons

Using SSA buttons (SAILOR 6120 only)

The recipient(s) of the Ship Security Alert must be configured in the

Mini-C Terminal according to the Flag Administration under which the vessel is sailing. The recipients can be e-mail addresses, phone numbers (SMS), fax numbers or telex numbers.

Install the SSA buttons and configure the Mini-C Terminal as described in

THRANE 6194 Terminal Control Unit, Installation and user manual [3].

Sending a covert Ship Security Alert (SSA)

To send a covert SSA, do as follows:

1. Open the cover for the red covert alert button.

2. Press the button.

•

Instant activation button: When pressed, an alert is sent immediately to

the configured SSA recipient(s).

•

Standard activation buttons: When pressed, an alert is sent after 30 –

33 seconds. If released (pressed again) within the 30 seconds, the alert is not sent. If the alert button is not released SSA Messages will be retransmitted every 30 minutes, until the button is released.

Using the green or yellow test button

The green or yellow button is a test button with a lamp. The button has momentary action (closed only as long as the button is pressed and held).

When the system is operational

1

, the test button is permanently lit. When the test button is pressed the light switches off and the covert alert buttons can be pressed without sending any alerts. If a covert alert button is pressed for 30 –

33 seconds during test, an SSA Test Message is sent to all recipients configured to receive test messages.

1.

“Operational” means the following criteria are met: GPS fix obtained, logged in, recipient(s) of covert alert configured, all SSA buttons connected correctly.

62 Using SSA buttons (SAILOR 6120 only)

Chapter 5

Troubleshooting

This chapter gives guidelines for troubleshooting and provides an overview of the different means of status signalling. It has the following sections:

•

Getting support

•

Updating software

•

Troubleshooting guide

Getting support

If this manual does not provide the remedies to solve your problem, you may want to contact your Airtime Provider or your local distributor.

To help with the troubleshooting, please generate a diagnostic report as described in the next page, and enclose the diagnostic report file when asking for support.

Airtime support

If you need assistance from your Airtime Provider, check your Airtime subscription documents for a contact number to call.

System support

If you need assistance with problems caused by one of your system units, please call a distributor in your area.

A list of certified partners and distributors is available on Thrane & Thrane’s web site: www.thrane.com

. Select Maritime and select Where to buy from the top menu bar.

5

63

Chapter 5: Troubleshooting

Updating software

Required tools and files

Before you can update the software you must get a download tool and the new software for the Mini-C Terminal.

Do as follows:

1. Open your browser and log into the Thrane &Thrane Extranet.

2. Find and download the zip file containing the Thrane &Thrane SNMP

upload application.

3. Extract the files to C:Thrane (create the folder if it is not already there).

Remember to select Use folder names.

4. On the Extranet, find the new software image for the Mini-C Terminal (.tiif file).

5. Download the .tiif file to the folder C:ThraneTFTP-Root (this folder should be created automatically when you extract the files from the zip file).

Updating the Mini-C Terminal software

Get the download tool and the new software as described in the previous section. Then do as follows:

1. Connect the Mini-C Terminal to the THRANE 6194 Terminal Control Unit and connect your computer to the LAN port on the THRANE 6194.

2. Start the SNMP upload tool (.exe file) placed in C:Thrane.

3. The application searches for units connected to the local network. When a unit is found, it is listed with IP address, description, serial number and software version.

Note

It may take some time for the Mini-C Terminal to appear in the list.

64 Updating software

Chapter 5: Troubleshooting

4. When the Mini-C Terminal appears in the list you can check the current software version in the sw-version column. If there are more than one

Mini-C Terminal you can recognize your unit by the serial number.

5. Click on your Mini-C Terminal to select it.

6. When the IP address of your Mini-C Terminal appears in the small field in the bottom left corner, click the button Upload software (.TIIF file).

7. Browse to the .tiif file in C:ThraneTFTP-Root.

8. Select the file and click Open.

The software is now updated and the Mini-C Terminal automatically restarts with the new software. You can use the SNMP upload application again to check the software version as in step 4 above.

Updating software 65

Chapter 5: Troubleshooting

Troubleshooting guide

The below table provides information on some of the problems that might occur, including possible causes and remedies to solve the problems.

Problem Possible cause Remedy

SAILOR 6150 only: The

Message

Terminal cannot switch off.

Software error

There is no signal or weak signal from the satellite.

The view to the satellite is blocked, or there is a hardware problem.

Push and hold the Power button for 10 seconds, or reboot via the power cable.

Make sure the SAILOR 3027 has a clear view in all directions. See the installation manual for details.

If the view is not blocked, check the error log. If the problem persists, contact your local distributor.

SAILOR 6150 only: No connection between

SAILOR 6006 and SAILOR 3027

The LAN cable between the

THRANE 6164 and the

SAILOR 6006 or the CAN cable between the

SAILOR 3027 and the

THRANE 6194 is damaged or is not properly connected.

Make sure the cables are properly connected and that the cables and connectors are not damaged.

No connection between easyMail and

SAILOR 3027

The PC connection to the

SAILOR 3027 is not set up properly.

For information on how to set up the PC connection, see

Setting up PC communication

with the Mini-C Terminal on page 53.

66 Troubleshooting guide

Chapter 5: Troubleshooting

Status signalling in easyMail

Status information

The top of the display shows the most important status information.

You can click each status area to get details, or use the View menu to enter the status pages.

Information of events

Popup windows

When an event requires your attention, a popup window appears.

When you have read the text, select OK to close the window. The latest event is shown in the info bar at the bottom of the page and is added to the information log.

Information log

To see the information log, select View > Info log.

The log shows the events that are registered in your Mini-C System.

Status signalling in easyMail 67

Chapter 5: Troubleshooting

Service and repair

Should your Thrane & Thrane product fail, please contact your dealer or installer, or the nearest Thrane & Thrane partner. You will find the partner details on www.thrane.com

where you also find the Thrane & Thrane Self

Service Center web-portal, which may help you solving the problem.

Your dealer, installer or Thrane & Thrane partner will assist you whether the need is user training, technical support, arranging on-site repair or sending the product for repair.

Your dealer, installer or Thrane & Thrane partner will also take care of any warranty issue.

Repacking for shipment

Should you need to send the product for repair, please read the below information before packing the product.

The shipping cartons for the SAILOR 6120/30/40/50 system have been carefully designed to protect the equipment during shipment. The cartons and their associated packing material should be used when repacking for shipment.

Attach a tag indicating the type of service required, return address, model number and full serial number. Mark the carton “FRAGILE” to ensure careful handling.

Note

Correct shipment is the customer’s own responsibility.

68 Service and repair

Appendix A

A

Conformity

The Mini-C Systems SAILOR 6120, SAILOR 6130, SAILOR 6140 and SAILOR 6150 are CE certified (R&TTE directive) as stated in “Declaration of Conformity with

R&TTE Directive”, enclosed in electronic copy on the next pages (one declaration for each system).

69

Appendix A: Conformity

74

Appendix B

B

GNU License texts

GNU General Public License

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the

GNU General Public License is intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This General Public License applies to most of the Free Software

Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software

Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.

To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The «Program», below, refers to any such program or work, and a «work based on the Program» means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term

«modification».) Each licensee is addressed as «you».

75

Appendix B: GNU License texts

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program).

Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the

Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this

License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

76 GNU General Public License

Appendix B: GNU License texts

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.

Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this

License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the

Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.

You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royaltyfree redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this

License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and «any later version», you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software

Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE

EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT

HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM «AS IS» WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE

PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

GNU General Public License 77

Appendix B: GNU License texts

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT

HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,

BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS

OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A

FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to apply these terms to your new programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the «copyright» line and a pointer to where the full notice is found.

Copyright (C)

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General

Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public

License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the

Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.

Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author

Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w’.

This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for details.

The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public

License. Of course, the commands you use may be called something other than `show w’ and `show c’; they could even be mouse-clicks or menu items—whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a «copyright disclaimer» for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision’ (which makes passes at compilers) written by James Hacker.

signature of Ty Coon, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.

78 GNU General Public License

Appendix B: GNU License texts

GNU Lesser General Public License

Version 2.1, February 1999

Copyright (C) 1991, 1999 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public

License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the

GNU General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages—typically libraries—of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public

License permits more lax criteria for linking other code with the library.

We call this license the «Lesser» General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this

GNU Lesser General Public License 79

Appendix B: GNU License texts case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public

License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a «work based on the library» and a «work that uses the library». The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General

Public License (also called «this License»). Each licensee is addressed as «you».

A «library» means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The «Library», below, refers to any such software library or work which has been distributed under these terms. A

«work based on the Library» means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term

«modification».)

«Source code» for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this

License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this

License, and its terms, do not apply to those sections when you distribute them as separate works. But when you

80 GNU Lesser General Public License

Appendix B: GNU License texts distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this

License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public

License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a «work that uses the Library». Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a «work that uses the Library» with the Library creates an executable that is a derivative of the

Library (because it contains portions of the Library), rather than a «work that uses the library». The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a «work that uses the Library» uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a «work that uses the Library» with the

Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable «work that uses the Library», as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)

GNU Lesser General Public License 81

Appendix B: GNU License texts b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the «work that uses the Library» must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components

(compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this

License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein.

You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

82 GNU Lesser General Public License

Appendix B: GNU License texts

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this

License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and «any later version», you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free

Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE

EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT

HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY «AS IS» WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE

LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT

HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE,

BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF

DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE

OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to apply these terms to your new libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the «copyright» line and a pointer to where the full notice is found.

Copyright (C)

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General

Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General

Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a «copyright disclaimer» for the library, if necessary. Here is a sample; alter the names:

GNU Lesser General Public License 83

Appendix B: GNU License texts

Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written by James Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

84 GNU Lesser General Public License

Glossary

CD

D

DNIC

E

EGC

ENID

Glossary

C

CAN Controller-Area Network. A message based protocol designed to allow microcontrollers and devices to communicate with each other within a vehicle without a host computer.

Compact Disk. An optical disc used to store digital data.

Data Network Identification Code

Enhanced Group Call. A type of broadcast data for ships.

EGC Network IDentification. An identification code used for reception of EGCs.

C

G

GMDSS

GNSS

GNU

GPL

Global Maritime Distress Safety System. The GMDSS system is intended to perform the following functions: alerting (including position determination of the unit in distress), search and rescue coordination, locating (homing), maritime safety information broadcasts, general communications, and bridge-to-bridge

communications.

Global Navigational Satellite System

GNU’s Not Unix. A Unix-like computer operating system developed by the GNU project, ultimately aiming to be a

«complete Unix-compatible software system» composed wholly of

free software

General Public License

85

ISP

L

LAN

Glossary

GPS Global Positioning System. A system of satellites, computers, and receivers that is able to determine the latitude and longitude of a receiver on Earth by calculating the time difference for signals from different satellites to reach the receiver.

I

IMN

IMSO

Inmarsat Mobile Number

International Maritime Satellite Organisation. An intergovernmental body established to ensure that Inmarsat

continues to meet its public service obligations.

Inmarsat Service Provider. The company providing the Inmarsat

services.

LES

LGPL

LRIT

Local Area Network. A computer network covering a small physical area, like a home, office, school or airport. The defining characteristics of LANs, in contrast to wide-area networks

(WANs), include their usually higher data-transfer rates, smaller geographic area, and lack of a need for leased telecommunication lines.

Land Earth Station

Lesser General Public License

Long Range Identification and Tracking. A system established by the IMO applying to all passenger ships, cargo ships > 300 gross tonnage and mobile offshore drilling units. These ships/units must automatically report their position to their Flag

Administration at least 4 times a day. Other contracting governments may request information about vessels in which they have a legitimate interest under the regulation.

86

Glossary

N

NAVAREA

NCS

P

PSDN

PSTN

M

METAREA mobile

MRCC

MSI

The geographic areas in which various governments are

responsible for meteorological warnings.

Mobile terminal. In this context the Mini-C Terminal

Maritime Rescue Co-ordination Centre

Maritime Safety Information. Maritime Safety Information. An internationally coordinated network of broadcasts of Maritime

Safety Information from official information providers, such as

National Hydrographic Offices, National Meteorological Offices,

Rescue Co-ordination Centres (RCCs), and The International Ice

Patrol, for Oceanic ice hazards.

The geographic areas in which various governments are responsible for navigation and weather warnings.

Network Coordination Station

PU

Public Switched Data Network

Public Switched Telephone Network. The network of the world’s public circuit-switched telephone networks. It consists of telephone lines, fibre-optic cables, microwave transmission links, cellular networks, communications satellites, and undersea telephone cables all inter-connected by switching centres which allows any telephone in the world to communicate with any other.

Position Unreserved

87

Glossary

S

SAC

SAR

SARF

SNMP

SOLAS

SSA

Short Access Code

Search And Rescue

Service Activation Registration Form. A form used to register your mobile equipment for activation of the services you are going to

use.

Simple Network Management Protocol. An Internet-standard protocol for managing devices on IP networks. It is used mostly in network management systems to monitor network-attached devices for conditions that warrant administrative attention.

(International Convention for the) Safety Of Life At Sea. Generally regarded as the most important of all international treaties

concerning the safety of merchant ships.

Ship Security Alert. The ship security alert system is provided to a vessel for the purpose of transmitting a security alert to the shore

(not to other vessel!) to indicate to a competent authority that the security of the ship is under threat or has been compromised.

T

TCU Terminal Control Unit

88

Index

Index

A

activation of service, 9

auto-print

EGCs and messages, 56

B

buttons

Distress, using, 60

SSA, using, 62

C

clear protocol, 39

conformity, 69

contacts, 30

D

data file, send, 24

data reporting and polling

description of service, 8

deleting

EGC, 37

message, 29

Distress

button test, 20

clear indications, 61

description of service, 5

message, write, 17

sending alert with SAILOR 6108, 60

settings, 17

Distress position, 19

document number

this manual, i

E

easyMail

menu overview, 16

using LAN, 53

using RS-232, 55

EGC

auto-print, 56

deleting, 37

description of service, 6

receiving, 36

setup, 44

event log, 67

G

GNU General Public License, 75

GNU Lesser General Public License, 79

I

Inbox, 29

info log, 67

L

LAN

setup with easyMail, 53

LES number

list of supported, 47

link test, 39

login, 38

D

89

Index

M

manual

document number, i

menu overview, 16

message

auto-print, 56

deleting, 29

Distress, 17

Inbox, 29

options, 25

Outbox, 30 sent items, 30

writing, 23

messaging

description of service, 7

mobile number

entering, 50

N

network

login, 38 scan, 38 view status, 38

O

Outbox, 30

P

position

for Distress, 19

viewing, 41

position information, 8

position reporting

description of service, 7

90

powering the system, 10

protocol, clear, 39

R

receiving EGCs, 36

registration, 9

reporting position, 8

RS-232

communication with easyMail, 55

S

safety summary, iv

SAILOR 6108 or SAILOR 3042E

sending Distress alert, 60

scan, 38

sent items, 30

serial communication with easyMail, 55

service activation, 9

services

data reporting and polling, 8

Distress, 5

EGC, 6

Inmarsat C details, 5

messaging, 7 position reporting, 7

sound

testing, 21

special access codes, 32

SSA buttons

using, 62

starting up, 10

status

network, 38

signalling, 67

support, 63

system overview

total, 2

system units, 3

T

transmission stop, 39

troubleshooting, 63

typography used in this manual, vii

U

units in the system, 3

user interface, 4

W

warranty, 68

writing messages, 23

Index

91

98-131590-A [email protected]

• thrane.com

SAILOR 6120 SSA System

Производитель

Thrane&Thrane

Состав

1. SAILOR 3027 SSA Terminal — INMARSAT антенна/трансивер
2. THRANE 6194 Terminal Contol Unit — Блок подключения и управления
3. SSA alert button — Стандартно 2 кнопки тревоги 3-x проводные и одна кнопка тестирования 4-х проводная.
4. Power supply — Блок питания

Программирование

Консоль RS232 COM Baud rate:115200

Подключить компьютер последовательным кабелем к блоку подключения и управления Thrane  6194
На компьютере запустить терминальную программу Putty или любую др.
Выбрать соответствующий COM порт и скорость обмена данными 115200
После включения, появится tt6194:/$
Команда подключения к терминалу MINI-C : minic
ответ: Сan0:/$
Далее ввести команду получения статуса администратора : su sysadm
Терминал запросит пароль pass:
При первом включении пароль : **** 
который необходимо будет поменять на другой.

Возможно подключение телнетом на адрес TCU (2 LAN кабеля + свич), но данный способ работает не очень корректно, лучше использовать подключение через консольный порт.

IP адреса (смотреть в TMA)

• IP трансивера 169.254.29.21 (?)
• IP TCU 169.254.173.109

Процедура программирования

Перед программированием обязательно получить у заказчика текст для программирования!

Для разных флагов строка для передачи может быть разной, обязательные параметры: Ship Name, MMSI, IMO, CALL.

Формат команды:
set (space) –am (space) – (entry),(type),{(address),(param)}

(Entry)- строка
Номер строки от 0 до 2 (0,1,2) т.о. максимально только 3 строки

(type)Типы сообщений :

0: TELEX — Телекс

1: FAX — Факсимильное сообщение

6: SMS — SMS сообщение и код береговой станции

254: EMAIL — Электронная почта

ПРИМЕР ДЛЯ ТЕЛЕКСНЫХ СООБЩЕНИЙ:

(set -am) “пробел” строка (0, 1, 2) “запятая” тип сообщения (0) “запятая” телексный номер 5519298 оканчивается знаком (+/) автоответ“TATJH” далее нажать (enter)

set –am 0,0,5519298+/TATJH (enter)

ПРИМЕР ДЛЯ ФАКСИМИЛЬНЫХ СООБЩЕНИЙ:

Команда (se -am) “пробел”, номер строки (0, 1, 2) “запятая” далее тип сообщения (1) “запятая” телефонный номер факса 4539558888 заканчивается (t30) нажать “enter”.

: set  –am  0,1,4539558888,t30              (enter)

ПРИМЕР ДЛЯ SMS СООБЩЕНИЙ:

Команда (set -am) “пробел”, номер строки (0, 1, 2) “запятая” типе сообщения (6) “запятая” номер мобильного телефона 4525414111 заканчивается кодом (LES SMS CODE) нажать “enter”
примерный формат для TELENOR LES.

: set   –am  0,6,4525414111,66              (enter)

Кроме France Telecom который использует специальный формат сообщения для доставки:

: set   –am  0,6,SMS+4525414111,29             (enter)

SEE LES SMS CODES BELOW:

TELENOR LES USE CODE (66)
XANTIC LES USE CODE (696)
FRANCE TELECOM USE CODE (29)
STRATOS LES USE CODE (696)

Помните о нобходимости регистрации терминала на используемый океанский регион для береговой станции LES
для доставки SMS сообщений (команда set –m)

: set -m 4,104,204,304

: SEt -m ALL_OCEANS

Alert LES for ocean 0     : 4
Alert LES for ocean 1     : 104
Alert LES for ocean 2     : 204
Alert LES for ocean 3     : 304

ПРИМЕР ДЛЯ АДРЕСОВ ЭЛЕКТРОННОЙ ПОЧТЫ:
команда (set -am) “пробел”, номер строки (0, 1, 2) “запятая” тип сообщения (254) “запятая” адрес эл.почты ssasalert@**.** нажать “enter”

: set –am  0,254,ssasalert@**.**               (enter)

Многоадресное программирование

можно запрограммировать несколько адресов доставки электронной почты и факс номеров но не более 79 знаков в одной строке.
Кроме SMS сообщений.

Команда проверки запрограммированых адресов и типа сообщений:

 set -am

Entry  Type  Param  Address
    0   254         qwer@thrane.com;tyui@thrane;asdf@thrane.com
    1     1    t30  4539551234;4539555678;4539550987
    2     6     66  4525414111

To set/clear addresses: set -am <Entry>,<Type>[,<Addresses>[,<Param>]]

Возможно задать вариант отправки сообщения: Alert, Test, Alert+Test

set -ame <Entry>,<Type>

Где <Entry> — номер сообщения, <Type> — вариант отправки сообщения: 1 = Alert, 2 = Test, 3 = Alert+Test

Подключение кнопок

1. Подключение тревожных кнопок трехпроводное, тестовая кнопка подключается по 4 проводам.
2. Возможно подключить до 6 кнопок тревоги
3. В минимальной комплектации одна кнопка «тест» (X14) и две «тревога». Для нормальной работы системы необходимо поставить перемычки между клеммами 1-2 «пустых» колодок, к которым кнопки не подключены. То есть перемычки 1-2 ставить с X7 по X12, исключая колодки с подключенными кнопками.

Практика программирования

Исходные данные:

Ship name:ATLANTIC
CallSign:999
IMO:111
MMSI:222
CSO VIKTOR 0079211234567,DSCO ANDREY 0079217654321

Covert message setup :
Destination type     : E-mail
Address              : vic@spb.ru;alert.isps@transport.gov.mt
Parameter            : 
Usage                : Msg+Test
Destination type     : E-mail
Address              : a@spb.ru;everyone@spb.ru
Parameter            : 
Usage                : Msg+Test
Destination type     : SAC
Address              : sms+79211234567;sms+79217654321
Parameter            : 29
Usage                : Msg+Test

Подключаемся к Mini-C

tt6194:/$ minic
Connecting... Connected, type ^D or exit to disconnect
can0:/$ su sysadm
Enter password: ***

Создаем в блокноте файл с таким содержимым (максимум 200 знаков):

В терминале EasyMail многострочный ввод не работает! Ставим PuTTY https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html

tr long.txt
Ship name:ATLANTIC
CallSign:999
IMO:111
MMSI:222
CSO VIKTOR 0079211234567,DSCO ANDREY 0079217654321

Выделяем его содержимое и копируем в буфер (Ctr+C), затем вставляем в консоль:

can0:/$ tr long.txt
Ship name:ATLANTIC
CallSign:999
IMO:111
MMSI:222
CSO VIKTOR 0079211234567,DSCO ANDREY 0079217654321

Таким способом мы создаем файл long.txt с необходимым содержимым

can0:/$ dir
         main.cfg Prio=172  ILLEGAL 13-01-11  09:07 18055 bytes
'''         long.txt Prio=  0     POLL 13-01-11  08:31 89 bytes'''
          _EGCLOG Prio=  0     POLL 70-01-01  00:00 0 bytes
last_power_on.cfg Prio=180  ILLEGAL 13-01-11  08:32 18055 bytes
           _RXLOG Prio=  0     POLL 70-01-01  00:00 0 bytes
           _TXLOG Prio=  0     POLL 13-01-11  09:28 1898 bytes
      factory.cfg Prio=180  ILLEGAL 70-01-01  00:00 3661 bytes
  part_number.txt Prio=180  ILLEGAL 70-01-01  00:00 50 bytes
      last_ok.cfg Prio=180  ILLEGAL 13-01-11  09:03 18055 bytes

Просмотр содержимого файла

can0:/$ type long.txt

Удалить файл можно командой

can0:/$ delete long.txt

Записываем в память командой

can0:/$ se -atf long.txt

Просмотреть содержимое памяти можно командой

can0:/$ se -at
Current text: 
Ship name:ATLANTIC
CallSign:999
IMO:111
MMSI:222
CSO VIKTOR 0079211234567,DSCO ANDREY 0079217654321
To change text: set -atf <filename>

Очистить содержимое памяти

can0:/$ se -at "пробел"

Вводим e-mail адреса и номера телефонов для доставки SMS

can0:/$ set -am 0,254,vic@spb.ru;alert.isps@transport.gov.mt
can0:/$ set -am 1,254,a@spb.ru;everyone@spb.ru
can0:/$ set -am 2,6,sms+79211234567;sms+79217654321,29

В последней строке параметр 29 для доставки SMS через France Telecom. Для TELENOR параметр должен быть 66.

Просматриваем:

can0:/$ set -am
Update time: 2013-01-11  09:54:31
Entry  Type  Param  Address
    0   254         vic@spb.ru;alert.isps@transport.gov.mt
    1   254         a@spb.ru;everyone@spb.ru
    2     6     29  sms+79211234567;sms+79217654321

To set/clear addresses: set -am <Entry>,<Type>[,<Addresses>[,<Param>]]

Таким образом сообщение будет отправлено на 4 почтовых адреса и 2 телефона.

Удаление строки

can0:/$ set -am <Entry>,255

Подключение ГЛОНАСС

To allow external navigational input

External navigational input     Command
Allow                           can0:/$ cfg -pa 1
Not allow                       can0:/$ cfg -pa 0

To display the current external navigational input, type:
can0:/$ cfg -pa
External nav input: 1 (Allowed)


To set preferred navigational input

Preferred navigational input     Command
GPS                              can0:/$ cfg -pi 1
Glonass                          can0:/$ cfg -pi 2

To display the currently preferred navigational input, type:
can0:/$ cfg -pi
Preferred nav input: 2 (External Glonass)

• Date: 17/09/2015
• Version: C
• Document ID: 98-131590
• File name: SAILOR 6120/30/40/50 mini-C — User Manual incl 6006MT
• Size: 2 mb
• Type:
  Manuals
• Products:

  SAILOR 6140 Maritime System
  SAILOR 6130 LRIT System
  SAILOR 6150 Non Solas System
  SAILOR 6120 mini-C SSA System