Швейная машина veritas innovation инструкция

Автоматическая намотка шпульки

Кол-во выполняемых петель:

Максимальная высота подъема лапки:

Максимальная длина стежка:

Максимальная скорость шитья:

Максимальная ширина стежка:

Освещение рабочей поверхности:

Регулировка баланса петли:

Регулировка давления лапки на ткань:

Регулировка скорости на корпусе

Съемная рукавная платформа:

4 /5

Оценка на основе мнений 2 покупателей

1. Manuals
2. Brands
3. VERITAS Manuals
4. Sewing Machine
5. Anna
6. Instruction manual

• Page 1
  SCHMETZ INSIDE Instruction manual www.facebook.com/veritassewing www.instagram.com/veritassewing www.veritas-sewing.com…
• Page 2
  Dear Customer, we congratulate you on your purchase of your sewing machine. You have bought a quality product which has been made with great care and, if serviced right, will serve you well for many years. Before using it for the first time, we ask you to read the manual at hand carefully, paying special attention to the safety instructions.
• Page 3
  Important safety instructions When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. DANGER — To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. 2.
• Page 4
  14. Never place anything on the pedal. 15. Never use the machine if the air vents are blocked, keep the air vents of the machine and the foot pedal free from dust, fusel and leftovers. 16. The machine must only be used with designated foot controller, in order to avoid a hazard.

• Page 5: Table Of Contents

  Contents Machine Introduction Principal parts of the machine …………….. 7 Accessories …………………… 8 Standard ……………………8 Optional ……………………8 Connecting machine to power source …………..9 Polarized plug information ………………9 Foot control ………………….. 9 Machine Settings Sewing table ………………….10 Free arm …………………….

• Page 6
  Utility Stitches Stretch stitch …………………….29 Straight stretch stitch ………………..29 Zigzag stretch stitch ………………..29 Sewing stretch fabrics and elastic tape …………..30 Overcasting stitch ………………….31 Blind Hem ……………………32 1-Step Buttonhole stitch ………………..33 Making a buttonhole on stretch fabrics ……………35 Button sewing …………………..36 Zipper insertion ………………….37 Inserting a centered zipper ………………37 Inserting a side zipper ………………..39…

• Page 7: Principal Parts Of The Machine

  Principal parts of the machine Tension dial Take-up lever Reverse sewing lever Thread cutter Sewing table and accessory box Stitch width dial (depends on models) Bobbin winder stopper Stitch length dial Pattern selector dial Buttonhole lever Needle threader (depends on models) Needle plate Needle clamp screw Presser foot…

• Page 8: Accessories

  Accessories Accessories are stored inside the accessory box. Standard 1. All purpose foot 2. Zipper foot 3. Buttonhole foot 4. Button sewing foot 5. Seam ripper/ brush 6. Edge/ quilting guide 7. Pack of needles 8. Spool holder 9. Bobbin (3x) 10.

• Page 9: Connecting Machine To Power Source

  Connecting machine to power source Attention: Always make sure that the machine is unplugged from power source and the main switch is off («O»). when the machine is not in use and before inserting or removing parts. Before connecting the power supply, make sure that the voltage and frequency shown on the rating plate is conforming with your main power.

• Page 10: Sewing Table

  Sewing table Hold the sewing table horizontally, then pull toward the left to remove it from the machine. Attach the sewing table, and then push it to the right. The inside space of the sewing table is used as an accessory box. Free arm Free-arm sewing is convenient for sewing tubular areas such as pant…

• Page 11: Two-Step Presser Foot Lifter

  Two-step presser foot lifter The presser foot lifter is to raise or lower your presser foot. When sewing multi-layers or thick fabrics, the presser foot can be further raised up manually to allow enough space for your sewing work. Note: The needle must always be at the highest position.

• Page 12: Winding The Bobbin

  Winding the bobbin 1. Place the thread and spool holder onto the spool pin. For better sewing quality, choose a proper size of the spool holder for the thread and attach it next to to the spool. 2. Draw the thread from the spool and place the thread in between the upper thread guide.

• Page 13
  6. Hold the thread tail securely in one hand. 7. Step on the foot control to start winding the bobbin. 8. After the bobbin has wound a few rounds, stop the machine and cut the thread near the hole of the bobbin.Continue filling the bobbin until it is full.

• Page 14: Inserting The Bobbin

  Inserting the bobbin Attention: Turn the power switch to off («O») before inserting or removing the bobbin. When inserting or removing the bobbin, the needle must be fully raised. Remove the sewing table, then open the hinged cover. Pull the bobbin case by the hinged latch.Remove the bobbin of the bobbin case.

• Page 15: Threading The Upper Thread

  Threading the upper thread Note: It is important to do the threading order correctly otherwise sewing problems may occur. 1. Raise the presser foot lifter. 2. Turn the handwheel towards you to bring the needle and take-up lever to highest position. 3.

• Page 16
  4. Draw the thread from the spool and place the thread in between the upper thread guide. 5. Guide the thread ahead and pull the thread through the pre-tension spring as illustrated. 6. Continue to guild the thread down to the silver discs to keep the thread in proper tension.

• Page 17: Using The Needle Threader (Depends On Models)

  Using the needle threader Attention: Turn the power switch to the off position («O»). Lower the presser foot lifter. Raise the needle to its hightest position by turning the handwheel toward you until the mark matched with the line on the machine.

• Page 18: Bringing Up The Bobbin Thread

  Bringing up the bobbin thread When making gathering or smocking, first bring up the bobbin thread as described below. Hold the upper thread with your left hand. Turn the handwheel towards you (counter-clockwise) to lower the needle down below the needle plate then raise it to bring the bobbin thread Gently pull on the upper thread to bring the bobbin thread up through the…

• Page 19: Replacing The Needle

  Replacing the needle Attention: Turn the power switch to off («O») when carrying out any of the operations below! Change the needle regularly, especially when it shows signs of wear or if it causes problems. Insert the needle following the illustrated instructions.

• Page 20: Matching Needle/ Fabric/ Thread

  Matching needle/ fabric/ thread NEEDLE SIZE FABRICS THREAD 65/9 — 75/11 Lightweight fabrics- Light-duty thread in cotton, nylon, thin cottons, voile, serge, silk, muslin, polyester or Qiana, interlocks, cotton knits, tricot, cotton wrapped jerseys, crepes, woven polyester, polyester. shirt & blouse fabrics. 80/12 Medium weight fabrics- Most threads sold…

• Page 21: Changing The Presser Foot

  Changing the presser foot Attention: Turn the power switch to off («O») when carrying out any of the operations below! Remove the presser foot Raise the presser foot bar. Press the back lever to release the presser foot. Lever Attach the presser foot Lower the presser foot holder until the cut-out meets the pin.

• Page 22: Thread Tension

  Thread tension Proper setting of tension is important for good sewing. There is no single tension setting appropriate for all the stitch functions and fabrics. Basic thread tension setting: «4». Normal thread tension for straight stitch sewing. Upper thread Bobbin thread Surface Wrong side Thread tension is too loose for straight…

• Page 23: How To Choose Your Pattern

  How to choose your pattern To select a stitch, simply turn the pattern selector dial. The pattern selector dial may be turned in either direction. For straight stitch, select pattern » » or » » with the pattern selector dial. Adjust the stitch length with the stitch length dial.

• Page 24: Straight Stitch

  Straight stitch Set the pattern as shown in figure. Turn the stitch length dial, and the length of the individual stitches will decrease as the dial approaches «0». The length of the individual stitches will increase as the dial approaches «4».

• Page 25: Zigzag Stitch

  Zigzag stitch Adjusting the stitch width The width increases as you move stitch width adjustment dial from «0-5». The width can be reduced on any patterns. Please use the stitch selection dial if the model is no stitch width dial Stitch width dial (depends on models) Adjusting the stitch length…

• Page 26: Useful Skills

  Useful skills Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project. The results may not be achieved requirement depending on types of fabric and stitching. Suggest to sew a piece of fabric firstly. For the trial sewing, use a piece of fabric and thread that are same as those used for your project and check the thread tension and stitch length and width.

• Page 27: Sewing Corners

  Sewing corners 1. Stop the sewing machine when you reach a corner. 2. Lower the needle into the fabric manually or by pressing the needle up/ down button once. 3. Raise the presser foot. 4. Use the needle as a pivot and turn the fabric 90°.

• Page 28: Reverse

  Reverse Reverse stitching is used to secure the threads at the beginning and at the end of a seam. Press the reverse sewing lever and sew 4-5 stitches. The machine will sew forward when the lever is released. Cutting the thread Bring the thread take up lever to its highest position, raise the presser foot and remove the fabric.

• Page 29: Stretch Stitch

  Stretch stitch Use this stitch with knitted tricot or other stretchy fabrics. The stitch enables your seam to stretch without breaking the thread. Good for easy to ravel and knit fabrics. It’s good for joining durable fabric such as denims. These stitches can also be used as a decorative top stitches.

• Page 30: Sewing Stretch Fabrics And Elastic Tape

  Sewing stretch fabrics and elastic tape When elastic tape is attached to the cuff or waist of a piece of clothing, the finished dimensions will be that of the stretched elastic tape. Therefore, it is necessary that a suitable length of the elastic tape be used. Pin the elastic tape to the wrong side of fabric at a few points to make sure that the tape is uniformly positioned…

• Page 31: Overcasting Stitch

  Overcasting stitch Sewing overcasting stitches along the edge of fabric prevent it from fraying. Sewing the overcasting along the edge of the fabric so that the needle drops over the edge of the fabric on the right 2.5~5 side. Needle drop point…

• Page 32: Blind Hem

  Blind Hem Secure the bottom of skirts and pants with a blind hem, this stitch will sew with invisible stitch on the right side of the fabric. Blind hem/lingerie for firm fabrics. Blind hem for stretch fabrics. 2.5~4 Note: It takes practice to sew blind hem. Always make a sewing test first.

• Page 33: 1-Step Buttonhole Stitch

  1-Step Buttonhole stitch Buttonholes can be adapted to the size of the button. For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better buttonhole sewing. Slightly reduce upper thread tension to produce better results. Note: Before sewing a buttonhole on your project, practice on a scrap piece of…

• Page 34
  Pull the buttonhole lever all the way down and position it behind the bracket on the buttonhole foot. Buttonhole lever Bracket Slightly hold the end of the upper thread and start sewing. Note: Gently feed the fabric by hand. Before stopping, the machine will automatically sew a reinforcement stitch after the buttonhole is sewn.

• Page 35: Making A Buttonhole On Stretch Fabrics

  Making a buttonhole on stretch fabrics When sewing buttonholes on stretch fabric, hook heavy thread or cord under the buttonhole foot. Attach the buttonhole foot. Bring the two gimp thread ends to the front of the foot and insert them into the grooves, then tie them there temporarily.

• Page 36: Button Sewing

  Button sewing Buttons can be sewn on with the sewing machine. Buttons with 2 or 4 holes can be attached. Install the darning plate. Position the work under the foot. Place the button in the desired position, lower the foot. Adjust the stitch width according to the distance between the two holes of the button.

• Page 37: Zipper Insertion

  Zipper insertion This foot can be set to sew on each side of the zipper, the edge of the foot guides the zipper to ensure straight placement. Attention: Zipper foot should be used for sewing 1.5~3 straight stitches only. It is possible that the needle could hit the presser foot and break when sewing other patterns.

• Page 38: Inserting A Side Zipper

  Inserting a side zipper Place the right sides of the fabric together. Sew a bottom seam 2cm from the right edge of the zipper bottom stop position. Sew a few stitches in reverse lock. Increase the stitch length to maximum, set the tension below 2 and baste the remaining length of the fabric.

• Page 39: Gathering

  Gathering Ideal for clothing as well as home decor. It works best on thin to medium weight fabrics. Before sewing, please check the upper and bobbin threads are already pulled out about 5cm to leave enough room for sewing. How to threading the bobbin thread, please refer to «Bringing up the bobbin thread «…

• Page 40: Smocking

  Smocking The decorative stitch created by stitching or embroidering over gathers is called «smocking». It is used to decorate the front of blouses or cuffs. The smocking stitch adds texture and elasticity to the fabric. Increase the stitch length to maximum, set the tension below 2 and basting lines 1cm across the area to be smocked.

• Page 41: Free Motion Darning, Embroidery And Monogramming

  Free motion darning, embroidery and monogramming Preparation for embroidering and monogramming * Embroider hoop is not included with the machine. Change the presser foot to the button sewing foot. Install the darning plate. Remove the presser foot and the presser foot holder. Draw the desired lettering or design on the surface of the fabric.

• Page 42: Darning

  Darning First sew around the edges of the hole (to secure the threads). Working from left to right, sew over the hole in a constant and continuous movement. Turn the work by 1/4 and sew over the first stitching moving the work slower over the hole to separate the threads and not form big gaps between the threads.

• Page 43: Quilting

  Quilting Sandwiching batting between the top and bottom layers of fabric is call «Quilting». The top layer is usually formed by multiple geometrically shaped pieces of materials joined together. Using the edge/ quilting guide Attaching the edge/ quilting guide in the presser foot holder as illustrated and set the space as you desire.

• Page 44: Patchwork Stitching

  Patchwork stitching Open the seam allowances and presses it flat. Wrong side Place the center of the presser foot on the seam line of the joined pieces of fabric and sew over the seam.

• Page 45: Applique

  Applique You can create and applique by cutting a different piece of fabric into a shape and using it as a decoration. Cut out the applique design and baste it on the fabric. 3.5~5 Sew slowly around the edge of the design.

• Page 46: Scallop Stitch

  Scallop stitch The wave-shaped repeating pattern, that looks like shells, is called «scalloping». It is used to decorate the collar of blouses and the edges of knitting projects. Scallop edging Stitch along the edge of the fabric, making sure not to sew directly on the edge of the fabric.

• Page 47: Maintenance

  Maintenance Attention: Disconnect the power cord from the wall socket before carrying out any maintenance, otherwise injury or electrical shock may result. Remove the stitch plate Turn the handwheel until the needle is fully raised. Remove the sewing table, then open the hinged cover.

• Page 48: Trouble Shooting Guide

  Trouble shooting guide Before calling for service, check the following as below. If the problem still persists, please contact the purchase place or your nearest authorized dealer. Problem Cause Correction Reference 1. The machine is not threaded 1. Rethread the upper thread. correctly.

• Page 49
  Problem Cause Correction Reference 1. The machine is not correctly 1. Check the threading and threaded. rethread. 2. The bobbin case is not 2. Thread the bobbin case as Loose threaded correctly. illustrated. stitches 3. Needle/ fabric/ thread 3. The needle size must suit the combination is wrong.

• Page 50: Disposal

  Problem Cause Correction Reference 1. The machine is not turned on. 1. Turn on the machine. The sewing machine 2. The presser foot lifter is raised. 2. Lower the presser foot lifter. doesn’t 3. The machine is not plugged in. 3. Connect the power cord to the operate electric outlet.

• Page 51
  Notes…
• Page 52
  IM_KX0N(EN)