Сигнализация игла инструкция по эксплуатации

Quick Links

• Page 1
  SERVICE MANUAL…
• Page 3
  Dear client! The anti-theft systems manufactured by AUTHOR are meant to be installed only in the certified installation centers in your region. The systems installed by non-certified centers or by individuals are not subjected to warrantee and service maintenance. 27/07/20 nRF52…

• Page 4: Table Of Contents

  FIRMWARE UPDATE …………6 BLED 112 drivers installation ……….6 The Author Flasher software installation ……9 The IGLA ALARM firmware update ……..10 Setting of the IGLA ALARM parameters ……13 Key fobs adding ……………..15 DE VICE ALIGNMENT ………..18 Alignment with the AUTOSTART-module……18 Alignment with ATLAS or COMPASS GSM/GPS …..19…

• Page 5: De Vice Connec Tion

  DE VICE CONNEC TION Wiring diagram The IGLA ALARM anti-theft system installation should be conducted when the ignition is turned off. The system should be installed in a secured place in the car inaccessible for criminals. The device should be set up with the additional module CONTOUR connection for some cars.

• Page 6
  12. Orange. «Minus» siren output (max 250 mA, see page number 4). 13. Violet. End switch (optional). In the IGLA ALARM device the violet wire is used for connection to an analog end switch (for example the end switch of the hood).

• Page 7: Siren Connection

  LIN-bus is not available in the particular car. After the IGLA ALARM system has been connected turn on the ignition. The car will be recognized automatically, the indication signals will begin to blink once in three seconds.

• Page 8: Additional Protective Contour

  Additional protective contour There may be connected the additional protective contour to the IGLA ALARM system for providing maximal protection to the car from being theft. It begins to work in the case the connection with the engine operating module through the CAN-bus has been interrupted or hindered.

• Page 9: Firmware Update

  2. Download the archive with the Author Flasher software and unpack it to any folder on the computer. 3. Transfer the IGLA ALARM to the firmware change mode and perform the updating procedure using the Author Flasher tool. BLED 112 drivers installation 1.

• Page 10
  Example of the device identifi cation 5. Click the right button of the mouse on the name of the device and in the drop-down menu choose the point «Update Driver Software…». Choose «Update Driver Software…» 6. Press on «Browse my computer for driver software» and enter the path to the folder that the drivers have been unpacked to.
• Page 11
  Choose «Browse my computer for driver software» Choose the folder with the just unpacked archive 7. Press the «Install» button. 8. After the installation process has been completed, the « Bluegiga Bluetooth Energy » device will appear in the list of the devices.

• Page 12: The Author Flasher Software Installation

  9. Installation of the driver has been fi nished. The Author Flasher software installation The Author Flasher application does not require installation and ready to be launched right after the archive with the newest version of the application has been unpacked. The application is supported only by Windows‑…

• Page 13: The Igla Alarm Firmware Update

  «dotNetFx45_Full_setup.exe». The IGLA ALARM firmware update Situate the computer with the BLED 112 USB‑dongle as close to the device as possible in order to arrange a stable connection.

• Page 14
  Perform the IGLA ALARM firmware change procedure: 1. Open the Author Flasher application by double click of the right button of the mouse on the AuthorFlasher.exe file. The USB dongle should be plugged in; otherwise the application will require to plug it in after having been started.
• Page 15
  3. Press «Refresh» in order to establish the connection between the IGLA ALARM and the BLED 112 Bluetooth USB-dongle. After identification of all of the available devices, they will appear in the device list. 4. Choose the device the firmware of which is planned to be updated and press «Flash».

• Page 16: Setting Of The Igla Alarm Parameters

  «Ground». Setting of the IGLA ALARM parameters The parameters of the IGLA ALARM can be adjusted through the Author Flasher application when the ignition is on. The radio version of the device being…

• Page 17
  1. Choose the IGLA ALARM among the available devices in the list and press the «Configure»-button. 2. Proceed to the «Read-write settings» — window and set the new values of the parameters of the device.

• Page 18: Key Fobs Adding

  Author Flasher application when the ignition is on. The radio version of the device should be 7.1 or above. 1. Choose the IGLA ALARM among the available devices in the list and press the «Configure» — button. 2. Transfer the device to the key fobs adding mode by clicking on the appropriate caption in the lower part of the window.

• Page 19
  3. Press «OK» in the opened window. All the key fobs and the smartphones previously added to the device will be erased from the memory of the device. 4. Insert the power supplying element holding the button on the key fob’s body pressed. The diode should start flashing with green.
• Page 20
  Both of the key fobs might be added to the system at a time. If the addition has been unsuccessful, the diode will stop flashing and the key fob will proceed to the «sleep»-mode in 30 seconds – the reduced energy consumption mode.

• Page 21: De Vice Alignment

  DE VICE ALIGNMENT When tying two or more devices to the IGLA ALARM, the alignment should be conducted in the PIN-code change mode by entering the valid PIN- code once again. If the gray wire is used for alignment of the devices, all the devices added sooner will be untied.

• Page 22: Alignment With Atlas Or Compass Gsm/Gps

  • The indication signal of the Autostart module; • The double indication signal of the IGLA ALARM. 6. Turn off the ignition and disconnect the red and the gray wires from the «plus»-wire for restarting of the devices. 7. Connect the red wires of the devices to the «plus»-wire again (do not connect the gray wire…

• Page 23
  4. For adding the COMPASS or the ATLAS device to the IGLA ALARM, the plastic card included in the same set with the ATLAS/COMPASS device is required (use the open code on the top of the card).

• Page 24: Alignment With Tor

  Alignment with TOR Only single TOR may be added to the IGLA ALARM system. 1. Connect both of the devices according to the wiring diagrams described in their manuals (do not connect the red and the gray wires of the TOR).

• Page 25: Alignment With The Contour-Module

  PIN-code once again when the accelerator is fully pressed When tying two or more devices to the IGLA ALARM, the alignment should be conducted in the PIN-code change mode by entering the valid PIN- code once again. If the gray wire is used for alignment of the devices, all the devices added sooner will be untied.

• Page 26: Alignment With The Kord-Module

  PIN-code once again when the accelerator is fully pressed When tying two or more devices to the IGLA ALARM, the alignment should be conducted in the PIN-code change mode by entering the valid PIN- code once again. If the gray wire is used for alignment of the devices, all the devices added sooner will be untied.

• Page 27: Alignment With The Keyless Block

  Alignment with the KEYLESS BLOCK A 1CAN/1LIN KEYLESS BLOCK module can be aligned with an IGLA ALARM in case they are connected to the same CAN-bus. If the KEYLESS BLOCK should be aligned with a 2CAN/2LIN IGLA ALARM, the connection should be conducted only through the CAN‑A‑bus.

• Page 28
  The IGLA ALARM and the KEYLESS BLOCK module alignment should be conducted when the key fob authentication mode is on. Otherwise the devices will be aligned, but authentication by the same key fob will be impossible. The connection will be broken as soon as the authentication mode is changed.
• Page 29
  4. If the IGLA ALARM has already been set up in a car and the KEYLESS BLOCK has not yet, transfer them into the alignment mode having fulfilled the next steps: • turn on the ignition without starting the engine;…

• Page 30: Fir S T Se T Tings A Djus Tment A Nd Choosing Of The Op Tions

  FIR S T SE T TINGS A DJUS TMENT A ND CHOOSING OF THE OP TIONS Initial setting of the PIN-code 1. Ensure that the ignition is turned on, the red and the gray wires are connected to a permanent «plus», the device is in the PIN-code change mode (the indication signal is being repeated once in three seconds).

• Page 31: The Igla Alarm Anti-Theft System Options

  The IGLA ALARM anti-theft system options All the additional information about the options of the device is described in the IGLA ALARM User guide. Option By entering the Service mode PIN- code or automatically Opening of the central lock Closing of the central lock (when…

• Page 32
  The options set by default colored in the table in gray. The figures in the cells of the table correspond to the number of the service/valet button pushes in order to turn on or off the particular option. Some additional options are available for some of the cars, for example: turning off the start-stop function, change of the indication signal etc.

• Page 33: Engine Blocking Method

  Engine blocking method The anti-theft IGLA ALARM system prevents the car from being stolen by stopping of the working engine or not allowing the engine to be started. The blocking method is automatically set when setting up the device in the car: •…

• Page 34: Additional Functions

  Additional functions Additional functions support depends on the year, brand and configuration of the car. Comfort This function is available for some cars. It comprises closing of the windows and the sunroof when being armed by the standard key. This function is turned-on by default.

• Page 35
  Additional functions Some of the additional options are available for some cars , for example: automatic turning off of the Start/ stop function, the indication signal change and so on. 1 See the official service website of the company: https://service. author-alarm.com/…

• Page 36: Deleting Of The Key Fobs

  (see page 35). The key fobs with the button may be tied only to the IGLA ALARM with the BLE nRF52 module (see the marking on the inner part of the manual cover). For automatic quick key fobs adding to the system, the Author Flasher software might be used.

• Page 37
  1. Retrieve the power supply elements out of all the key fobs (including the key fobs previously added to the system) and turn off the Bluetooth on all the smartphones. 2. Erase all the key fobs previously recorded in the system memory and turn off the ignition.
• Page 38
  If connection has not been successful, flashing of the diode will stop in 30 seconds after installation of the power supplying element and the key fob will be transferred in the «sleep» mode with low energy consumption. In this case, repeat the pairing procedure once again.
• Page 39
  4. Enter the key fobs adding mode as shown in the respective passage on page 34. 5. Insert the power supplying element into the new key fob. The diode of the key fob will start flashing with green once in a second. Successful connection will be confirmed with the red light of the diode.
• Page 40
  The key fobs with no buttons may be added to the device with the radio module version 7.2 or above (see the information on the label on the box). 1. Retrieve the power supply elements out of all the key fobs (including the key fobs previously added to the system) and turn off the Bluetooth on all the smartphones.

• Page 41: Authentication By The Key Fobs Of The Keyless Block

  (available for Android only). Authentication by the key fobs of the KEYLESS BLOCK The authentication process in the IGLA ALARM can be undergone by the key fobs included in the KEYLESS BLOCK set. For this purpose, the devices should be aligned (see page 24).

• Page 42: Key Fobs Indication Table

  Key fobs indication table The diode of the key fob provides the indication signals according to the next table: Color Signal Event Green Single The battery is high Single The battery is low Orange The built-in accelerometer (Green + seconds is malfunctioned Red) Green…

• Page 43: Authorization (Authentication) Modes

  Engine start will be permitted even in the case the engine start prohibition mode is used in the system. However, the IGLA ALARM will stop the engine at the attempt to move if the PIN-code has not been entered.

• Page 44: Anti-Hijack Mode

  In order to choose the step-by-step or two-step authentication modes, authentication in the system should be undergone by the key fobs or by the smartphone. Two-step authentication mode is used for providing maximal safety to the car. In this mode engine start will be permitted only in the case both of the conditions, introduced below, have been abided: •…

• Page 45: Super Antihijack Mode

  Super AntiHiJack mode This mode allows you to protect the driver and the car, in the moment when IGLA ALARM is disarmed. To activate “Super AntiHiJack” mode, enable the corresponding option. By default, the “Super AntiHiJack” option is disabled in the system.

• Page 46
  If the current PIN-code encompasses slight press of the accelerator, enter the PIN-code once again and press the accelerator to the floor. 5. Assign a new service/valet button: press the button that is meant to be used as a service/valet button 21 times.
• Page 48
  User Manual…