Zoom livetrak l 12 инструкция

2017 ZOOM CORPORATION

Copying or reprinting this manual in part or in whole without permission is prohibited. Product names, registered trademarks and company names in this document are the property of their respective companies. All trademarks and registered trademarks in this document are for identification

purposes only and are not intended to infringe on the copyrights of their respective owners.

You must read the Usage and Safety Precautions before use.

Operation Manual

Usage and Safety Precautions

In this operation manual, symbols are used to highlight warnings and cautions that you must read to pre- vent accidents. The meanings of these symbols are as follows.

Warning

Something that could cause serious injury or death Caution

Something that could cause injury or damage to the equipment

Other symbols used

An action that is mandatory An action that is prohibited

Warning Operation using an AC adapter

Never use any AC adapter other than a ZOOM AD-19. Do not do anything that could exceed the ratings of outlets and other electrical wiring equipment.

Before using the equipment in a foreign country or other region where the electrical voltage differs, al- ways consult with a shop that carries ZOOM products and use the appropriate AC adapter.

Alterations Do not open the case or modify the product.

Caution Product handling

Do not drop, bump or apply excessive force to the unit. Be careful not to allow foreign objects or liquids to enter the unit.

Operating environment Do not use in extremely high or low temperatures. Do not use near heaters, stoves and other heat sources. Do not use in very high humidity or where it could be splashed by water. Do not use in places with frequent vibrations. Do not use in places with much dust or sand.

AC adapter handling When disconnecting the power plug from an outlet, always pull on the plug itself. Disconnect the power plug from the outlet when the unit will not be used for a long time and whenev- er there is lightning.

Connection cables and input/output jacks Always turn the power OFF for all equipment before connecting any cables. Always disconnect all connection cables and the AC adapter before moving the unit.

Volume Do not use at a loud volume for a long time.

Interference with other electrical equipment In consideration of safety, the has been designed to minimize its emission of electromagnetic waves and to suppress interference from external electromagnetic waves. However, equipment that is very susceptible to interference or that emits powerful electromagnetic waves could result in interference if placed nearby. If this occurs, place the and the other device farther apart. With any type of electronic device that uses digital control, including the , electromagnetic interfer- ence could cause malfunction, corrupt or destroy data and result in other unexpected trouble. Always use caution.

1

Cleaning Use a soft cloth to clean the exterior of the unit if it becomes dirty. If necessary, use a damp cloth that has been wrung out well to wipe it. Never use abrasive cleansers, wax or solvents such as alcohol, benzene or paint thinner.

Breakdown and malfunction If the unit becomes broken or malfunctions, immediately disconnect the AC adapter, turn the power off and disconnect other cables. Contact the store where you bought the unit or ZOOM service with the fol- lowing information: product model, serial number and specific symptoms of breakdown or malfunction, along with your name, address and telephone number.

Copyrights Windows is a registered trademark of Microsoft Corporation. Macintosh, Mac OS and iPad are trademarks or registered trademarks of Apple Inc. The SD, SDHC and SDXC logos are trademarks. Other product names, registered trademarks and company names in this document are the property of their respective companies. Note: All trademarks and registered trademarks in this document are for identification purposes only and are not intended to infringe on the copyrights of their respective owners.   Recording from copyrighted sources, including CDs, records, tapes, live performances, video works and broadcasts, without permission of the copyright holder for any purpose other than personal use is prohi- bi-ted by law. Zoom Corporation will not assume any responsibility related to infringements of copyrights.  

Note about the Auto Power Off function The power will automatically turn off if unused for 10 hours. If you want the power to stay on always, refer to Disabling the automatic power saving function.  

FCC regulation warning (for U.S.A.) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursu- ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal- lation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

For EU Countries

Declaration of Conformity

2

Introduction Thank you very much for purchasing a ZOOM LiveTrak . The has the following features.

12-channel digital mixer & multitrack recorder

The combines a digital mixer with 12 total input channels (8 mono and 2 stereo), a multitrack re-

corder that can simultaneously record up to 14 tracks, and a 14-in/4-out USB audio interface. Compact and

lightweight, this digital mixer is easy to transport and can even be used with PA systems for live perfor-

mances in rehearsal studios, cafs and other small venues.

High-quality mic preamps

The has high-quality mic preamps built-in for 8 channels. The high-quality analog inputs, which

can provide +48 V phantom power, have a 128 dBu EIN rating and +60 dB maximum input gain. In addi-

tion, channels 1 and 2 also support Hi-Z input, while channels 3 to 8 have PAD functions (26 dB attenua-

tion), enabling them to accept high levels of input.

5 MONITOR OUT channels

In addition to the MASTER OUT, the also has 5 MONITOR OUT channels. The MONITOR OUT mixes

can be set separately for each output. Since these support headphone output, headphones are all that are

needed to send different mixes to each performer.

Digital mixer that can be operated intuitively

Opening menus is not necessary with the . Every mixer parameter can be controlled with knobs

and keys just like an analog mixer. Each channel has a 3-band EQ, and the mono channels have compres-

sor functions. The mixer also includes high-quality send effects. In addition, up to 9 mixer status scenes

can be saved in the unit.

Recorder can simultaneously record 14 tracks and play 12 tracks

The can simultaneously record every channel and the master fader stereo signal output for a total

of 14 tracks. Since the recorded data is saved in 16/24-bit, 44.1/48/96 kHz WAV format, the files can easily

be copied to a computer and used in a DAW. In addition, overdubbing and punching in/out can be done as

expected with a multitrack recorder.

14-in/4-out USB audio interface

The can be used as a 14-in/4-out USB audio interface. The signals from each input and the master

fader output can be recorded in a DAW. In addition, signals output from a computer can also be assigned

to a stereo channel.

Class compliant mode, which enables connection with iOS devices, is also supported.

3

Contents Usage and Safety Precautions

Introduction

Names and functions of parts Top

Rear panel

Equipment connection example Live PA system

Display overview Home Screen

Turning the unit on/off Turning the unit on

Turning the power off

Using the MENU screen

Mixer Outputting input sounds from output devices

Adjusting the tone and panning

Using the built-in effects

Using scene functions

Setting signals output from MONITOR OUT AE

Recording and playback Preparing to record

Recording and playing tracks

Adding marks

Redoing parts of recordings (punching in/out)

Mixing down tracks

Recording automatically

Capturing audio before recording starts

Selecting the folder where projects are saved

Selecting projects for playback

Using the metronome Enabling the metronome

Changing metronome settings

Using the slate mic Recording with the slate mic

Changing slate mic settings

Projects Changing project names

Deleting projects

Protecting projects

Checking project information

Saving projects to USB flash drives

Importing projects from USB flash drives

Managing marks

Audio files Deleting audio files

Exporting audio files to USB flash drives

Importing audio files from USB flash drives

Using audio interface functions Installing the driver

Connecting to a computer

Inputting return signals from the computer to a

stereo channel

Using card reader functions

Recording and playback settings Changing the recording format

Changing automatic recording settings

Showing recording levels on level meters

Enabling latency adjustment

Changing the playback mode

SD card settings Checking the open space on SD cards

Formatting SD cards

Testing SD card performance

Various settings Setting the date and time

Setting the footswitch

Changing the sampling rate

Disabling the automatic power saving function

Adjusting the display contrast

Restoring settings to factory defaults

Checking the firmware versions

Updating the firmware

4

Troubleshooting

Specifications

Send effects specifications

Mixer block diagram

5

Names and functions of parts

Top

Input channel section

MIC/LINE input jack

48V switch/indicator

Hi-Z switch PAD switch SIG indicator

GAIN knob

COMP knob

SEL button

REC/PLAY button

MIC/LINE input jack These input jacks have built-in mic preamps. Connect mics, keyboards and guitars to them.

These can be used with both XLR and 1/4-inch (balanced or unbalanced) phone plugs.

48V switch/indicator This turns +48 V phantom power on or off. Turn this on ( ) to supply

phantom power to MIC/LINE input jacks 14 (or 58).

The indicator lights when the switch is on.

Hi-Z switch Use to switch the input impedance of MIC/LINE input jack 1 (or 2).

6

Turn it on ( ) when connecting a guitar or bass guitar.

PAD switch This attenuates (reduces) the input signal of the equipment connected

to the MIC/LINE input jack by 26 dB.

Turn this on ( ) when connecting line level equipment.

SIG indicator This indicator shows the signal level after adjustment by the GAIN knob.

The indicator color changes according to the signal level.

Lit red: 3 dB

Lit green: 48 to 3 dB

GAIN knob Use to adjust the input gain of the mic preamp.

The range of adjustment depends on the on/off status of the MIC/LINE input jack switch (Hi-Z on chan-

nels 12 or PAD on channels 38).

Jack Adjustment range

MIC/LINE input jack 12 (XLR) +16 +60 dB

MIC/LINE input jack 12 (TRS) Hi-Z off +16 +60 dB

Hi-Z on (TS) +6 +50 dB

MIC/LINE input jack 38 PAD off +16 +60 dB

PAD on -10 +34 dB

COMP knob Use to adjust the amount of compression.

SEL button Use to select a channel for parameter adjustment in the channel strip section.

Channels with lit SEL buttons are affected by channel strip section adjustments.

REC/PLAY button Use this button to switch between recording input signals to the SD card and playing back an already

recorded file from the SD card.

Status Explanation

Lit red Input signals will be recorded to the SD card after passing through the compressor.

Lit green An already recorded file will be played back. Playback signals are input before the equalizer. In this state, signals from input jacks are disabled.

Unlit Files will neither be recorded nor played back.

7

LINE input jacks (TS)

LINE input jacks (RCA)

USB button

MUTE button

Level meter

Channel fader

LINE input jacks (TS) Use these input jacks to connect line level equipment. For example, connect keyboards or audio devic-

es.

These can be used with 1/4-inch (unbalanced) phone plugs.

NOTE If only the left LINE input jack (TS) channel is connected, it will be handled as a mono channel.

LINE input jacks (RCA) Use these input jacks to connect line level equipment. For example, connect audio devices.

These can be used with RCA pin connectors.

NOTE If both the RCA and TS LINE input jacks are connected, the TS input jacks will be used.

8

USB button This switches the signals input to channels 9/10 (or 11/12).

Lit: audio return signal output from the computer

Unlit: LINE input jacks

NOTE Connect the to a computer as an audio interface. ( Connecting to a computer)

MUTE button This mutes or unmutes signals.

To mute the channel, press this button to light it.

HINT This has no effect on recording to the SD card.

Level meter This shows the signal level after adjustment by the channel fader.

Ranges shown: -48 dB 0 dB

NOTE If the actual channel fader position differs from the channel fader position recalled using the scene func- tion, for example, the level meter will show the recalled fader position.

Channel fader This adjusts the channel signal level in a range from to +10 dB.

9

CHANNEL STRIP section

MID FREQ knob

MID knob

LOW knob

LOW CUT button

HIGH knob EQ OFF button

SEND EFX knob

PAN knob

EQ OFF button When this button is lit, HIGH, MID, LOW and LOW CUT are bypassed.

HIGH knob This adjusts the boost/cut of high-frequency equalization.

Type: shelving

Gain range: 15 db +15 dB

Frequency: 10 kHz

MID FREQ knob This adjusts the central frequency of the mid frequency equalization.

Frequency (in Hz): 100, 140, 200, 250, 315, 500, 800, 1k, 1.3k, 2k, 3k, 5k or 8k

MID knob This adjusts the boost/cut of mid-frequency equalization.

Type: peaking

Gain range: 15 db +15 dB

Frequency: set by MID FREQ knob

LOW knob This adjusts the boost/cut of low-frequency equalization.

Type: shelving

Gain range: 15 db +15 dB

Frequency: 100 Hz

LOW CUT button This turns on/off the high-pass filter, which cuts low frequencies.

When ON, signals below 75 Hz are attenuated 12 dB/octave.

SEND EFX knob The amount that can be sent to the SEND EFX bus can be set from to +10 dB.

10

PAN knob Use to adjust the channel position in the stereo field.

On a stereo input channel, this adjusts the volume balance between the left and right channels.

11

FADER MODE section

MASTER and AE buttons

MASTER and AE buttons These switch between the mixes output from the MASTER OUT and MONITOR OUT AE jacks.

MASTER button: Use to show and adjust the mix output from the MASTER OUT jacks.

AE buttons: Use to show and adjust the mixes output from the MONITOR OUT AE jacks.

NOTE The parameters that can have separate settings for the MASTER and AE mixes are as follows. — Fader positions (each channel)

12

SCENE section

ON button

RESET button

19 buttons

RECALL button

SAVE button

ON button Press this button, lighting it, to use the scene function

RESET button Press this button to reset the current mixer settings to the factory defaults.

19 buttons Use these buttons to select the scene to use to save the current mixer state and to load saved scenes.

If the current mixer settings match the settings of a scene, the corresponding number button will light.

This unit can save up to 9 scenes.

RECALL button Use this button when loading scenes saved to buttons 19.

When this button is pressed, buttons 19 will blink if they have saved scenes and be unlit if they do not.

To recall a saved scene, press a blinking button between 1 and 9. To cancel recalling a scene, press the

RECALL button again.

SAVE button Use this button when saving the current mixer settings to a scene.

When this button is pressed, buttons 19 will light if they have saved scenes and be blink if they do not.

To save a scene, press a button between 1 and 9 to save it to that number. To cancel saving a scene,

press the SAVE button again.

13

Send effect (SEND EFX) section

Effect type list

TYPE knob

Parameters 1 and 2

EFX RETURN MUTE button

EFX RETURN level meters

EFX RETURN fader

Effect type list This is the list of the built-in effects.

The name of the currently selected effect lights.

It blinks when being selected.

If some time passes without a different effect being selected, the previously selected effect will remain

selected.

TYPE knob Use to select the built-in effect.

Turn this knob to select the effect type, and press it to confirm.

Parameters 1 and 2 Use these to adjust the parameters for the selected effect.

See Send effects specifications for the parameters of each effect.

EFX RETURN MUTE button This mutes or unmutes the signal sent from the built-in effect.

To mute the signal, press this button to light it.

14

EFX RETURN level meters These show the levels of the signals sent from the built-in effect to the master bus after adjustment by

the EFX RETURN fader. Their range is from 48 dB to 0 dB.

EFX RETURN fader This adjusts the levels of the signals sent from the built-in effect to the master bus in a range from

dB to +10 dB.

NOTE If the actual channel fader position differs from the channel fader position recalled using the scene func- tion, for example, the level meters will show the recalled fader position.

15

Output section

MASTER OUT jacks MONITOR OUT A jacks MONITOR OUT A PHONES jack

MONITOR OUT BE PHONES jacks

MONITOR OUT A knob MONITOR OUT A PHONES knob

MONITOR OUT BE knobs

MASTER REC/PLAY button

MASTER MUTE button

MONITOR OUT A switch

MONITOR OUT BE switches

Master level meters

Master fader

MASTER OUT jacks These jacks output signals after volume adjustment by the master fader.

Connect them to a power amplifier, a PA system or speakers with built-in amplifiers, for example.

These support balanced output with XLR connectors (2 HOT).

MONITOR OUT A jacks These jacks output signals after volume adjustment by the MONITOR OUT A knob.

You can, for example, connect a monitoring system for the mixer operator here.

These support balanced 1/4-inch jack phone output.

NOTE The MONITOR OUT A jacks can be set to output the same signals as the MASTER OUT jacks or the sig- nals set separately in the fader mode section. ( Selecting MONITOR OUT AE output signals)

MONITOR OUT A PHONES jack This headphone jack outputs signals after volume adjustment by the MONITOR OUT A PHONES knob.

NOTE The MONITOR OUT A PHONES jack always outputs the same signals as the MONITOR OUT A jacks.

16

MONITOR OUT BE PHONES jacks These headphone jacks output signals after volume adjustments by the MONITOR OUT BE PHONES

knobs.

NOTE The MONITOR OUT BE jacks can be set to output the same signals as the MASTER OUT jacks or the signals set separately in the fader mode section. ( Setting signals output from MONITOR OUT AE)

MONITOR OUT A knob Use to adjust the volume of the signals output from the MONITOR OUT A jacks.

MONITOR OUT A PHONES knob Use to adjust the volume of the signals output from the MONITOR OUT A PHONES jack.

MONITOR OUT BE knobs Use to adjust the volumes of the signals output from the MONITOR OUT BE PHONES jacks.

MONITOR OUT A switch This switches MONITOR OUT A output between the L/R jacks and the PHONES jack.

Status Explanation

MASTER ( ) The same signals as the MASTER OUT are output.

A ( ) The signals set in the FADER MODE section are output.

MONITOR OUT BE switches These switch the signals output from the MONITOR OUT BE PHONES jacks.

Status Explanation

MASTER ( ) The same signals as the MASTER OUT are output.

B-E( ) The signals set in the FADER MODE section are output.

MASTER REC/PLAY button Use this button to switch between recording the signal input on the master bus to the SD card and play-

ing back an already recorded file from the SD card.

Status Explanation

Lit red The signal will be recorded to the SD card after adjustment by the master fader.

Lit green The playback signal of a file is inserted on the master bus. The REC/ PLAY buttons of other channels will be unlit at this time.

Unlit Files will neither be recorded nor played back.

MASTER MUTE button This mutes or unmutes the MASTER OUT jacks.

To mute the signals, press this button to light it.

Master level meters These show the signal levels output from the MASTER OUT jacks in a range from 48 dB to 0 dB.

17

Master fader This adjusts the signal levels output from the MASTER OUT jacks in a range from to +10 dB.

NOTE If the actual channel fader position differs from the channel fader position recalled using the scene func- tion, for example, the level meters will show the recalled fader position. However, the position of the master fader is not shown when AUTO REC is activated.

18

RECORDER section

Slate mic

STOP button

REW button

FF button

SLATE button/indicator

Display

MENU button

Selection encoder

TEMPO button/indicator

PLAY/PAUSE button/indicator

REC button/indicator

OVER DUB button/indicator

Slate mic This is a built-in mic for recording comments.

This mic input is active while the SLATE button is being pressed.

The input channel can be set to channels 112, MASTER, or all channels. ( Changing the slate mic

routing)

SLATE button/indicator This activates the slate mic.

The slate mic is activated while this button is being pressed and its indicator is lit.

Display This shows the recorder status and MENU screen.

MENU button This opens the menu.

Selection encoder Use this to change menus and values and to move between items.

Operation Result

Turn when main recorder screen open

Search forward or backward in one-second increments.

Push when main recorder screen open

This sets a mark.

Turn when menu open Move between parameters and change values.

Press when menu open Confirm parameter value.

TEMPO button/indicator This sets the tempo of the metronome built into the recorder.

Press this button to make the recorder detect the tempo from the average value.

19

During recording and playback, the indicator blinks at a tempo of 40.0250.0 bpm.

See Changing metronome settings for metronome settings.

STOP button This stops the recorder.

PLAY/PAUSE button/indicator This starts and pauses recorder playback. The indicator shows the playback status as follows.

Status Explanation

Lit green The recorder is playing back.

Blinking green Playback is paused.

REC button/indicator This puts the recorder in recording standby. The indicator shows the recording status as follows.

Status Explanation

Lit red The recorder is recording or in recording standby.

Blinking red Recording is paused.

REW button Press to move to the previous mark.

If no mark is set, this moves to the beginning.

Press this button when at the beginning to move to the previous project.

Press and hold to search backward. (The longer you press, the faster the speed becomes.)

FF button Press to move to the next mark.

If it is the last mark, this moves to the end of the file. Press this button again to move to the next project.

Press and hold to search forward. (The longer you press, the faster the speed becomes.)

OVER DUB button/indicator

Status Explanation

Lit (ON) Record by overwriting into the current project folder.

Unlit (OFF) Create a new project folder and make a new recording.

20

Rear panel

P

O W

E R

s w

it ch

D

C IN

1 2V

A C

a d

ap te

r co

n n

ec to

r

U

S B

H O

S T

p o

rt

M

O D

E s

w it

ch

U

S B

D E

V IC

E p

o rt

C

LA S

S C

O M

P LI

A N

T M

O D

E

sw it

ch

S

A M

P LE

R A

T E

s w

it ch

S

D c

ar d

s lo

t

C

O N

T R

O L

IN ja

ck

POWER switch This turns the on and off.

Switch to to turn the power on. Switch to to turn the power off.

When the POWER switch setting is changed to OFF, the current mixer settings are automatically saved

in the unit and in the settings file in the project folder on the SD card.

DC IN 12V AC adapter connector Connect the included AC adapter here.

USB HOST port This USB 2.0 HOST port is for connecting USB flash drives.

Projects and audio files can be saved on and loaded from connected USB flash drives.

MODE switch Set whether to use as a USB HOST, card reader or audio interface.

This cannot be changed after starting up.

USB DEVICE port This USB 2.0 port is for connecting with a computer.

It will start up as a card reader or audio interface, depending on the MODE switch selection.

Card reader mode

Operating as an SD card reader, data can be exchanged with a computer.

Audio interface mode

Operating as an audio interface, audio data can be exchanged with a computer.

Inputs: The signals from channels 112 after they pass through their compressors and the master fader

output signals are input to the computer.

Outputs: Outputs from the computer can be assigned to channels 9/10 and 11/12.

Use when connected to an iOS device is possible if the CLASS COMPLIANT MODE switch is set to ON.

21

CLASS COMPLIANT MODE switch Use this to turn Class Compliant Mode ON/OFF.

Set it to ON when connected to an iOS device.

SAMPLE RATE switch Set the sampling rate used by the unit.

This cannot be changed after starting up.

SD card slot This slot is for SD cards.

The supports SD, SDHC and SDXC card specifications.

HINT You can test whether an SD card can be used with the . ( Testing SD card performance)

CONTROL IN jack A footswitch (ZOOM FS01) can be connected here.

The footswitch can be assigned to one function:

starting/stopping recorder playback, manually punching in/out or muting/unmuting the built-in effect. (

Setting the footswitch)

22

Equipment connection example

Live PA system

Headphones

Performer headphones4

Powered speakers (main)

Keyboard

Drums

Drum mics 3

Electric guitar

Vocal/chorus mics 2

Electric acoustic guitar

Bass

Portable audio player

DI

23

Footswitch

4

3

2

Computer (for recording and

playback)

DI

24

Display overview

Home Screen

No Item Explanation

Project name This shows the project name. «<» appears if there is another project before this one in the folder. «>» appears if there is another project after this one in the folder.

Status icon

This shows the status as follows. : Stopped : Paused : Recording : Playing back

Counter This shows the hour: minute: second.

Progress bar This bar shows the amount of time in the project from beginning to end.

Folder name The folder where the project is saved will be shown as FOLDER01 FOLD- ER10.

PLAY MODE icon This shows the PLAY MODE setting.( Changing the playback mode)

Metronome icon This is shown when the metronome is enabled. ( Enabling the metronome)

Project protection icon This is shown when project protection is enabled.( Protecting projects)

Remaining recordable time This shows the remaining recordable time. This will change automatically according to the number of channels that have

recording enabled with .

Recording file format This shows the recording file format used by the recorder.

Current date and time This shows the current date and time.

SD card icon This is shown when an SD card is being recognized.

Mark This shows the mark number and the status as follows.

: at mark (mark added at counter location) : not at mark (mark not added at counter location)

Longest file time in project This shows the length of the longest file in the project.

25

Turning the unit on/off

Turning the unit on

POWER switch

GAIN knob

Channel faders

EFX RETURN fader

Master fader

Input/Output jacks

DC IN 12V AC adapter connector

1. Confirm that the output devices connected to the are turned off.

26

2. Confirm that is set to OFF.

3. Plug the AD-19 adapter designed for this unit into an outlet.

4. Set all knobs and faders to their minimum values.

5. Connect instruments, mics, speakers and other equipment.

HINT Equipment connection example ( Equipment connection example)

6. Set to ON.

7. Turn on the output devices connected to the .

NOTE

When using a passive guitar or bass guitar, connect it to channel 1 or 2, and turn on. ( Top) When using a condenser mic, turn on. ( Top) The power will automatically turn off if the is unused for 10 hours. If you want the power to stay

on always, disable the automatic power saving function ( Disabling the automatic power saving func- tion)

27

Turning the power off

1. Minimize the volume of devices connected to the .

2. Turn off the power of output devices connected to the .

3. Set to OFF.

The following screens appear and the power turns off.

NOTE When the power is turned off, the current mixer settings are saved in the project on the SD card. If they cannot be saved to the SD card, they will be saved in the unit.

28

Using the MENU screen

Recorder function settings, for example are made for the using the MENU screen. This is an expla-

nation of the basic menu operations.

Open the menu: Press

This opens the MENU screen.

Select menu items and parameters: Turn

This moves the cursor.

Confirm menu items and parameters: Press

This opens the selected MENU screen or parameter setting screen.

Return to previous screen: Press

This opens the selected MENU screen or parameter setting screen.

On the following pages, menu screen operations are shown in the following way.

For example, «After selecting ‘METRONOME’ on the MENU screen, select ‘CLICK'»

becomes:

Select MENU > METRONOME > CLICK

29

Mixer

Outputting input sounds from output devices

Outputting sound from speakers

GAIN knob

MUTE button

MUTE button

Channel faders Master fader

1. Use to adjust the input signals while inputting sound from instruments and mics.

NOTE Set them so that SIG indicators do not light red.

SIG indicator

2. Turn off (unlit) for the MASTER and the channels with sound you want to output.

3. Set the MASTER fader to 0.

4. Use the channel faders to adjust the volumes.

5. Use the MASTER fader to adjust the overall volume.

30

Outputting sound from headphones

MONITOR OUT A PHONES knob

MONITOR OUT A PHONES jack

MONITOR OUT A switch

1. Connect headphones to the MONITOR OUT PHONES A jack.

2. Set to MASTER ( ).

3. Use to adjust the volume.

31

Adjusting the tone and panning

CHANNEL STRIP section

SEL button

1. Press to light it for the channel for which you want to adjust tone and panning.

2. Use the knobs and buttons in the channel strip section to adjust the tone and panning.

Adjusting the tone: , , , ,

Adjusting the panning:

NOTE

Press to light it, turning off all equalization at once. This will bypass HIGH, MID, LOW and LOW CUT settings.

Using the compressor ( Input channel section)

HINT Details about knobs and buttons ( CHANNEL STRIP section)

32

Using the built-in effects The has 16 types of send effects

SEND EFX knob

SEL button

EFX RETURN fader

TYPE knob

Parameters 1 and 2

EFX RETURN MUTE button

1. Turn to select the effect type, and press to confirm.

Lit: Effect selected

2. Press to turn it off, unmuting the EFX RETURN.

3. Set the EFX RETURN fader to 0.

4. Press the for the channel that you want to use the effect on to light it.

5. Use to adjust the amount for each channel.

6. Use the EFX RETURN fader to adjust the overall effect amount.

7. Use and to adjust the send effect parameters.

NOTE

See Send effects specifications for the parameters of each effect that can be adjusted by and .

33

Using scene functions The scene function can be used to save up to nine sets of current mixer settings

as scenes and to recall these saved settings at any time.

ON button

RESET button

19 buttons

RECALL button

SAVE button

Saving scenes

1. Click so that it lights.

This enables the scene function.

2. Press .

Buttons will light if they have saved scenes and blink if they do not.

Press again if you do not want to save a scene.

3. Press the button where you want to save the scene.

34

NOTE Nine scenes are saved in the unit. ( SCENE section) If a button that already has a scene saved is selected, that scene will be overwritten. The following items are saved with scenes. — Fader positions (each channel, SEND EFX, MASTER) — MUTE ON/OFF (each channel, SEND EFX, MASTER) — EQ OFF — LOW CUT ON/OFF — EQ HIGH — EQ MID — EQ MID FREQ — EQ LOW — SEND EFX — PAN — SEND EFX TYPE — SEND EFX parameters 1 and 2 — USB button setting

Recalling scenes

1. Click so that it lights.

This enables the scene function.

2. Press .

Buttons will blink if they have saved scenes and be unlit if they do not.

Press again if you do not want to recall a scene.

3. Press the button for the scene you want to recall.

The scene for the selected number is recalled.

NOTE If the actual channel fader position differs from the channel fader position shown, the volume will not change until the fader is moved to the same position. ( Input channel section)

35

Resetting mixer settings

1. Click so that it lights.

This enables the scene function.

2. Press .

Buttons will blink if they have saved scenes and be unlit if they do not.

Press again if you do not want to reset the settings.

3. Press .

The current mixer settings are reset to their factory defaults.

36

Setting signals output from MONITOR OUT AE The MONITOR OUT AE jacks can be set to output the same mix as the MASTER OUT or different mixes.

MONITOR OUT switches

MASTER button

AE buttonsChannel faders

Adjusting the MONITOR OUT AE mixes

1. Press an button to select the output to mix.

The selected output button lights and operation of all the channel faders is enabled.

NOTE The level meters show the fader positions. If the actual channel fader position differs from the channel fader position shown, the volume will not change until the fader is moved to the same position.

2. Use the channel faders to adjust the volumes.

37

Selecting MONITOR OUT AE output signals

1. Use the MONITOR OUT switch for an output to select its output signal.

To output a mix set using MONITOR OUT AE:

Set MONITOR OUT switch to AE ( )

To output the same mix as the MASTER:

Set MONITOR OUT switch to MASTER ( )

Output different mixes for MONITOR OUT AE

Output same mix as MASTER

NOTE Each output mix is saved with the scene and project. MONITOR OUT AE do not output send-return effect signals. The parameters that can have separate settings for the MASTER and MONITOR OUT AE are as fol-

lows. — Fader positions (each channel)

Copying a mix

1. While pressing the button ( or ) for the output you want to copy for at least 2 seconds,

press a blinking copy destination button ( or ).

This copies the mix from the source to the destination.

38

Recording and playback

Preparing to record

Inserting SD cards

POWER switch SD card slot

1. Set to OFF.

2. Open the SD card slot cover, and insert an SD card all the way into the slot.

To remove an SD card, push it further into the slot and then pull it out.

NOTE Disable write-protection on the SD card before inserting it.

Always set to OFF before inserting or removing an SD card. Inserting or removing a card while the power is on could result in data loss. When inserting an SD card, be sure to insert the correct end with the top side up as shown. If an SD card is not loaded, recording and playback are not possible. To format an SD card, see Formatting SD cards.

39

Creating new projects

The manages recording and playback data in units called projects.

1. Select MENU > PROJECT > NEW PROJECT.

2. Use to select YES, and press .

NOTE See Projects for information about projects. When a new project is created, it will start with the current mixer settings.

HINT When the power is turned on, it will automatically load the last used project.

40

Recording and playing tracks The has recorder functions that enable simultaneous recording of up to 14 tracks and simultane-

ous playback of up to 12 tracks.

The signals from every channel after they pass through their compressors and from the master fader out-

put can be recorded. These recordings can also be played back.

Recording

REC/PLAY button

PLAY/PAUSE button

REC button

OVER DUB but- tonSTOP button

1. Use to turn overdubbing on or off. OVER DUB indicator Lit (on): Overwrite current project Unlit (off): Create and record to new project

2. Press for the channels you want to record, lighting these buttons red.

3. Press to start recording standby.

HINT

If a recorded file already exists, and is off, pressing will create a new project and then start recording standby.

4. Press to start recording.

41

5. Press to stop recording.

NOTE The signals for each channel are recorded after passing through their compressors. ( Mixer block

diagram) Punching in/out ( Redoing parts of recordings (punching in/out)) Starting recording automatically ( Recording automatically) Capturing audio before recording starts ( Capturing audio before recording starts) When recording stops, Please Wait appears on the display. Do not turn the power off or remove the

SD card while this message appears. Doing so could cause data loss or malfunction.

42

Playing recordings

REC/PLAY button

PLAY/PAUSE button

STOP button

1. Press for the channels you want to play, lighting these buttons green.

2. Press to start playback. PLAY/PAUSE indicator Lit: Playing back Blinking: Paused

3. Press to stop playback.

NOTE Playback signals are added before the equalizer section, so their EQ and panning settings can be ad-

justed during playback. ( Mixer block diagram) Selecting projects for playback ( Selecting projects for playback) Changing the playback mode ( Changing the playback mode) Other channels cannot be played back when the MASTER channel is playing back.

43

Adding marks Adding marks at desired positions with the recorder makes moving to those positions easy.

Selection encoder

>>| button

|<< button

Adding marks during recording and playback

1. Press during recording/playback.

Moving in mark order

1. Use these buttons to move in mark order.

Move to next mark: Press

Move to previous mark: Press

NOTE Checking and deleting marks in projects ( Managing marks)

HINT A maximum of 99 marks can be added to one project.

You can also delete a mark by pressing the when at the mark position.

44

Redoing parts of recordings (punching in/out) Punching in/out is a function that can be used to rerecord parts of already recorded tracks. «Punching in»

is switching track status from playback to recording. «Punching out» is switching track status from record-

ing to playback.

With the , punching in/out can be conducted using buttons on its top or a footswitch (ZOOM FS01).

Selection encod- er

PLAY/PAUSE button

REC/PLAY button

STOP button REC button OVER DUB button

1. Press the to turn it on (lighting its indicator).

2. Press repeatedly for the tracks to re-record until they light red.

3. Press or turn left to move to before the part to be rerecorded.

4. Press to start playback.

5. Press at the position where you want to start rerecording (punch in).

6. Press to end rerecording (punch out).

NOTE Punching in/out using a footswitch (ZOOM FS01) ( Setting the footswitch) Punching in/out overwrites recordings. Punching in/out can be done up to 99 times each time playback is started.

7. Press to stop playback.

45

Mixing down tracks A final stereo mix can be recorded to the master track.

Signals are sent to the master track after passing through the master fader.

Recording to the master track

1. Click so that it lights.

NOTE Adjust the volume and panning of each recorded track before starting.

2. Press MASTER repeatedly until it lights red.

3. Press to return to the recording beginning.

4. Press to start recording standby.

5. Press to start recording.

6. Press to end mixing down.

46

Playing the master track

1. Press MASTER repeatedly until it lights green.

2. Press .

NOTE

To stop master track playback, press MASTER repeatedly until it becomes unlit. When the master track is playing, other tracks will not be played back. To listen to master track playback from a MONITOR OUT, set the MONITOR OUT AE switch to MASTER

( ).

47

Recording automatically Recording can be started and stopped automatically in response to the level after passing through the

master fader.

Selection encod- er

Master fader

MENU button REC button

1. Select MENU > REC/PLAY > AUTO REC > ON / OFF.

2. Use to select ON, and press .

NOTE Making additional settings for automatic recording ( Changing automatic recording settings)

3. Press repeatedly to return to the main recorder screen.

4. Press .

The indicator will light and recording standby will start.

48

The MASTER level meters will blink at the level that will cause automatic recording to start.

HINT Recording starts automatically when the input exceeds the set level (shown by the MASTER level me- ters). You can also set recording to stop automatically when the input goes below a set level. ( Setting auto- matic stopping)

5. Press to end recording standby or stop recording.

NOTE This function cannot be used with the PRE REC, METRONOME or PRE COUNT functions. When you

turn AUTO REC on, these other functions will be disabled. When you turn OVER DUB on, AUTO REC will be disabled.

49

Capturing audio before recording starts The input signal can be captured for up to 2 seconds before recording is started (pre-recording). Setting

this in advance can be useful when a performance

starts suddenly, for example.

1. Select MENU > REC/PLAY > PRE REC.

2. Use to select ON, and press .

NOTE This function cannot be used with the AUTO REC, METRONOME, PRE COUNT or OVER DUB functions. When you turn AUTO REC or PRE COUNT on, PRE REC will be disabled. The PRE REC function continues to be enabled even when recording is paused.

50

Selecting the folder where projects are saved Choose one of ten folders as the folder where recorded projects will be saved.

1. Select MENU > FOLDER.

2. Use to select the folder where you want to save, and press .

NOTE Up to 1000 projects can be saved in a single folder. If a folder that does not have a project is selected, a new project will be created automatically.

51

Selecting projects for playback Projects saved on SD cards can be loaded.

1. Select MENU > PROJECT > SELECT.

2. Use to select the project you want to load, and press .

NOTE Projects in different folders cannot be selected. To select a project that is saved in a different folder,

select that folder first. ( Selecting the folder where projects are saved) When a project is loaded, the mixer settings saved in that project are also loaded. If actual channel fader positions differ from the channel fader positions of the loaded project, the level

meters will show the recalled fader positions. The volume will not be changed until the actual fader position becomes the same as the recalled position.

When switching to a different project, the project mixer settings of the current project are saved to the settings file in the project folder.

52

Using the metronome

The metronome has adjustable volume, a selectable sound, and a precount function. The volume

can also be adjusted separately for each output.

Metronome settings are saved separately with each project.

Enabling the metronome

1. Select MENU > METRONOME > CLICK.

2. Use to select when the metronome makes sound, and press .

Setting value Explanation

OFF The metronome does not make sound.

REC AND PLAY The metronome sounds during recording and playback.

REC ONLY The metronome sounds only during recording.

PLAY ONLY The metronome sounds only during playback.

53

Changing metronome settings

Selection encoder

MENU button

TEMPO button

Changing the metronome tempo

1. Press .

The current tempo is shown on the display.

2. Do one of the following to change the tempo.

Turn

Press repeatedly at the tempo you want to set

54

Setting the precount

A metronome count can be sounded before starting recording/playback.

1. Select MENU > METRONOME > PRE COUNT.

2. Use to select the precount behavior, and press .

Setting value Explanation

OFF No precount will sound.

18 Before recording/playback, the precount will sound for the set number of times (18).

SPECIAL Before recording/playback, the precount will sound as shown below.

NOTE The precount is enabled even during playback. This function cannot be used with the AUTO REC function. When you turn AUTO REC on, PRE COUNT

will be disabled. This function cannot be used with the PRE REC function. When you turn PRE COUNT on, PRE REC will

be disabled.

55

Changing the metronome sound

1. Select MENU > METRONOME > SOUND.

2. Use to select the sound, and press .

HINT The options are BELL, CLICK, STICK, COWBELL and HI-Q.

NOTE Press to play the metronome and check the sound.

Changing the metronome pattern

1. Select MENU > METRONOME > PATTERN.

2. Use to select the pattern, and press .

HINT The options are 1/48/4 and 6/8.

NOTE Press to play the metronome and check the pattern.

56

Changing the metronome volume

The metronome volume can be adjusted separately for the MASTER OUT and each of the MONITOR OUT

AE outputs.

1. Select MENU > METRONOME > LEVEL > MASTER or A-E.

2. Turn to adjust the volume, and press .

HINT Set from 0 to 100.

NOTE Press to play the metronome and check the volume.

57

Using the slate mic

The has a built-in slate mic that allows comments to be recorded.

Selection encoder

MENU button

SLATE button

Recording with the slate mic

1. Start recording. ( Recording)

2. Press to enable the slate mic.

While is being pressed, the indicator lights and the slate mic is enabled.

NOTE When the slate mic is in use, signals from input jacks are muted to the channels to which the slate mic

is routed. None of the channel faders affect the level of the slate mic.

58

Changing slate mic settings

Changing the slate mic volume

1. Select MENU > SLATE > LEVEL.

2. Turn to adjust the volume, and press .

Changing the slate mic routing

1. Select MENU > SLATE > ROUTING.

2. Turn to select a channel for routing.

3. Press confirm.

ALL: Set routing to all channels at once ALL CLEAR: Clear all settings

Channel routing for slate mic input

ON

OFF

4. Press .

HINT

Pressing toggles it ON/OFF.

59

Projects

The manages recording and playback data in units called projects.

The following data is saved in projects.

Audio data

Mixer settings

Send return effect settings

Mark information

Metronome settings

Changing project names The name of the currently loaded project can be changed.

MENU button

REC button

Selection encoder

1. Select MENU > PROJECT > RENAME.

2. Edit the name.

Move cursor or change character: Turn

Select character to change/confirm change: Press

60

NOTE The default project name is the date and time of creation.

For example, if a project was created at 6:48:20 p.m. on March 14, 2017, the project name would be «170314_184820» (YYMMDD-HHMMSS).

Project names have 13 characters. The following characters can be used in project and file names.   (space) ! # $ % & ‘ ( ) + , — 0 1 2 3 4 5 6 7 8 9 ; = @   A B C D E F G H I J K L M N O P Q R S T U V W X Y Z ^ _ `   a b c d e f g h i j k l m n o p q r s t u v w x y z { } Projects can be ordered by numerical or alphabetical order. Project/file names cannot be only spaces. The project name is the same as the project folder name on the SD card.

3. Press .

61

Deleting projects Projects inside the selected folder can be deleted.

1. Select MENU > PROJECT > DELETE

2. Use to select the project you want to delete, and press .

3. Use to select YES, and press .

NOTE Projects cannot be deleted if protection is ON.

62

Protecting projects The currently loaded project can be write-protected, preventing the project from being saved, deleted or

having its content changed.

1. Select MENU > PROJECT > PROJECT PROTECT.

2. Use to select ON, and press .

NOTE Projects cannot be used for recording if protection is ON. Turn protection OFF to record. When protection is OFF for a project, it will always be saved to the SD card when the power is turned

off or another project is loaded. We recommend turning protection ON to prevent accidentally saving changes to a musical project after it has been completed.

63

Checking project information Various information about the currently loaded projects can be viewed.

1. Select MENU > PROJECT.

2. Use to select INFORMATION, and press .

Items shown Explanation

NAME Project name

PATH Location where project saved

DATE Project creation date and time (YYYY/MM/DD HH:MM:SS)

FORMAT Recording format

SIZE Project size

TIME Project length (HHH: MM: SS)

FILES Information about tracks and files

64

Saving projects to USB flash drives A USB flash drive can be connected directly to the , and the currently loaded project can be saved

to it.

MENU button

MODE switch

USB HOST portPOWER switch

Selection encoder

1. Set to OFF.

2. Connect the USB flash drive to the USB HOST port.

3. Set to USB HOST.

4. Set to ON.

5. Select MENU > PROJECT > PROJECT EXPORT.

6. Edit the name.

Move cursor or change character: Turn

Select character to change/confirm change: Press

65

NOTE The default project name is the date and time of creation.

For example, if a project was created at 6:48:20 p.m. on March 14, 2017, the project name would be «170314_184820» (YYMMDD-HHMMSS).

Project names have 13 characters. The following characters can be used in project and file names.   (space) ! # $ % & ‘ ( ) + , — 0 1 2 3 4 5 6 7 8 9 ; = @   A B C D E F G H I J K L M N O P Q R S T U V W X Y Z ^ _ `   a b c d e f g h i j k l m n o p q r s t u v w x y z { } Projects can be ordered by numerical or alphabetical order. Project/file names cannot only be spaces. The project name is same as the project folder name on the SD card.

7. Press .

8. Use to select YES, and press .

NOTE The folder structure on USB flash drives is as follows.

Never change this folder structure.

ZOOM_L-12

PROJECT

AUDIO

Folder where project data is saved

Folder where audio data is saved

Projects will be saved on the USB flash drive in the «PROJECT» subfolder of the «ZOOM_L-12» folder. Never disconnect a USB flash drive when Saving or Loading appears on the display.

66

Importing projects from USB flash drives Projects saved on USB flash drives can be copied to SD cards.

NOTE Use a computer to create «ZOOM_L-12» and «PROJECT» folders on the USB flash drive in advance ( Saving projects to USB flash drives). Only projects inside the «PROJECT» folder can be imported.

1. Set to OFF.

2. Connect the USB flash drive to the USB HOST port.

3. Set to USB HOST.

4. Set to ON.

5. Select MENU > PROJECT > PROJECT IMPORT.

6. Use to select the project you want to load from the USB flash drive, and press .

7. Edit the name.

Move cursor or change character: Turn

Select character to change/confirm change: Press

67

NOTE The default project name is the date and time of creation.

For example, if a project was created at 6:48:20 p.m. on March 14, 2017, the project name would be «170314_184820» (YYMMDD-HHMMSS).

Project names have 13 characters. The following characters can be used in project and file names.   (space) ! # $ % & ‘ ( ) + , — 0 1 2 3 4 5 6 7 8 9 ; = @   A B C D E F G H I J K L M N O P Q R S T U V W X Y Z ^ _ `   a b c d e f g h i j k l m n o p q r s t u v w x y z { } Projects can be ordered by numerical or alphabetical order. Project/file names cannot only be spaces. The project name is the same as the project folder name on the SD card.

8. Press .

9. Use to select YES, and press .

NOTE Imported projects are saved in the currently selected folder. Never disconnect a USB flash drive when Saving or Loading appears on the display.

68

Managing marks A list of marks in the currently loaded project can be opened, allowing them to be checked, played and

deleted.

MENU button

REC button

Selection encoder

1. Select MENU > PROJECT > MARK LIST.

A list of marks appears.

Indicates added mark

E mark indicates time when skipping occurred

during recording

2. Use to select a mark, and play or delete it.

Press to move to the mark position.

Press to delete the mark.

69

Audio files

The creates the following types of audio files according to the recording channel.

Channels 18: mono WAV files

Channels 9/10, 11/12 and MASTER: stereo WAV files

The file format depends on the sampling rate ( Changing the sampling rate) and quantization bit depth (

Changing the recording format) used by the unit.

The can also play back audio files created using DAW software ( Importing audio files from USB

flash drives).

NOTE The names given to audio files depend on their channels.

Channels 18: TRACK01TRACK08 Channels 9/10, 11/12: TRACK09_10, TRACK11_12 MASTER: MASTER

If the file size exceeds 2GB during recording, a new file will be created automatically in the same proj- ect and recording will continue without pause. When this happens, numbers will be added to the ends of the file names: -01, -02 and so on.

Deleting audio files Audio files that are not needed can be deleted.

MENU button

REC button

Selection encoder

1. Select MENU > PROJECT > FILE DELETE.

70

2. Use to select the file you want to delete, and press .

NOTE Press to select/deselect all files.

3. Press .

4. Use to select YES, and press .

NOTE Audio files cannot be deleted if protection is ON for their projects.

71

Exporting audio files to USB flash drives The desired audio files can be exported from projects to USB flash drives.

Exported audio files will be saved on the USB flash drive in the «AUDIO» subfolder of the «ZOOM_L-12»

folder.

MENU button

REC button

Selection encoder

1. Set to OFF.

2. Connect the USB flash drive to the USB HOST port.

3. Set to USB HOST.

4. Set to ON.

5. Select MENU > PROJECT > FILE EXPORT.

6. Use to select the file you want to export, and press .

72

7. Edit the name.

Move cursor or change character: Turn

Select character to change/confirm change: Press

NOTE Audio file names have 24 characters. The following characters can be used in project and file names.   (space) ! # $ % & ‘ ( ) + , — 0 1 2 3 4 5 6 7 8 9 ; = @   A B C D E F G H I J K L M N O P Q R S T U V W X Y Z ^ _ `   a b c d e f g h i j k l m n o p q r s t u v w x y z { } Project/file names cannot only be spaces.

8. Press .

9. Use to select YES, and press .

NOTE Never disconnect a USB flash drive when Saving or Loading appears on the display. Audio files will be saved on the USB flash drive in the «AUDIO» subfolder of the «ZOOM_L-12» folder.

73

Importing audio files from USB flash drives The desired audio files can be imported from USB flash drives to existing projects and assigned to chan-

nels.

NOTE Use a computer to create «ZOOM_L-12» and «AUDIO» folders on the USB flash drive in advance ( Sav- ing projects to USB flash drives). Only audio files inside the «AUDIO» folder can be imported.

1. Set to OFF.

2. Connect the USB flash drive to the USB HOST port.

3. Set to USB HOST.

4. Set to ON.

5. Select MENU > PROJECT > FILE IMPORT.

6. Use to select the file you want to import, and press .

NOTE Audio files cannot be imported from USB flash drives into projects that have protection ON.

7. Use to select the channel where you want to assign the file, and press .

74

NOTE Mono WAV files can be assigned to mono channels and stereo WAV files can be assigned to stereo

channels. Files cannot be imported to channels that already have files assigned to them. When files are imported, their file names will automatically be changed according to their import chan-

nels.

8. Use to select YES, and press .

NOTE Never disconnect a USB flash drive when Saving or Loading appears on the display.

75

Using audio interface functions

The can be used as a 14-in/4-out USB audio interface. After applying its compressor, each input

channel always outputs its signal to the corresponding USB audio channel. Channels 112 and the stereo

signal output from the master fader are sent to the computer (14 channels total).

Installing the driver

1. Download the «ZOOM L-12 Driver» from http://www.zoom.co.jp to the computer.

NOTE You can download the latest «ZOOM L-12 Driver» from the above website. Download the driver for the operating system that you are using.

2. Launch the installer and install the driver.

Follow the instructions that appear on screen to install the ZOOM L-12 Driver.

NOTE See the Installation Guide included in the driver package for detailed installation procedures.

76

Connecting to a computer

MODE switch USB DEVICE port

POWER switch

1. Use a USB cable to connect the USB DEVICE port to the computer.

2. Set the switch to AUDIO INTERFACE.

3. Set to ON.

NOTE

Set to ON when connected to an iOS device. When connecting to an iOS device, use a Lightning to USB camera adapter (or Lightning to USB 3 cam-

era adapter).

4. Set the as the computer sound device.

NOTE Audio interface functions cannot be used when the sampling rate is set to 96 kHz.

77

Inputting return signals from the computer to a stereo channel

USB buttons

1. Turn the , button channel ON for the stereo channel to use for input.

The signal controlled by the channel is switched to the USB audio channel signal (before EQ).

78

Using card reader functions

When connected to a computer, data on the SD card can be checked and copied.

MODE switch

USB DEVICE port POWER switch

1. Use a USB cable to connect the USB DEVICE port to the computer.

2. Set to CARD READER.

3. Set to ON.

NOTE When operating as a CARD READER, other functions and buttons cannot be used.

79

Recording and playback settings

Changing the recording format The recording format can be changed in consideration of audio quality and file size.

1. Open MENU > REC / PLAY > REC FORMAT.

2. Use to change the format, and press .

HINT When overwriting a recording, recording will occur at the bit depth of the original file. For example, a file recorded at 16-bit cannot be overwritten with 24-bit recording.

80

Changing automatic recording settings The conditions for automatically starting and stopping recording can be set.

Setting the automatic recording start level

1. Open MENU > REC / PLAY > AUTO REC > REC START LEVEL.

2. Use to change the start level, and press .

Recording will start automatically when the level of the MASTER fader output signal exceeds the

set level.

HINT This can be set from 48 to 0 dB.

81

Setting automatic stopping

1. Open MENU > REC / PLAY > AUTO REC > AUTO STOP.

2. Use to select the automatic stop time, and press .

HINT This can be set to OFF or between 0 and 5 seconds.

3. Open MENU > REC / PLAY > AUTO REC > REC STOP LEVEL.

4. Use to set the stop level, and press .

Recording will stop automatically when the level of the MASTER fader output stays below the set

level for the amount of time set in step 2.

NOTE If you start recording after setting automatic recording starting and stopping, the level set in step 4 will be shown on the MASTER level meters.

82

Showing recording levels on level meters The signals of levels recorded to the recorder or recorded to a computer when using the audio interface

function can be shown on the level meters of each channel.

1. Open MENU > REC / PLAY > REC LEVEL METER.

2. Use to select ON, and press .

If recorded signal levels are higher than post fader levels, the recorded signal levels are shown lit

dimly on the level meters.  

Enabling latency adjustment When overdubbing, adjustment can be made for the delay caused by analog-to-digital conversion, signal

processing and digital-to-analog conversion.

1. Open MENU > REC / PLAY > LATENCY ADJUST.

2. Use to select ON, and press .

83

Changing the playback mode

1. Open MENU > REC / PLAY > PLAY MODE.

2. Use to select the play mode, and press .

Setting value Explanation

OFF Only the selected project plays back. Playback continues even when the end of a file is reached.

PLAY ONE (single song playback)

Only the selected project plays back. Playback stops when when the end of a file is reached.

PLAY ALL (all song playback)

Every project from the selected one to the last one will be played back.

REPEAT ONE (single song repeat playback)

The selected project will be played repeatedly.

REPEAT ALL (all song repeat play- back)

All projects in the selected folder will be played repeatedly.

84

SD card settings

Checking the open space on SD cards

1. Open MENU > SD CARD > REMAIN.

This shows the open space on the card.

NOTE The shows less than the actual open space in order to maintain space to prevent SD card writing performance from degrading.

Formatting SD cards Format SD cards for use with the .

1. Open MENU > SD CARD > FORMAT.

2. Use to select YES, and press .

NOTE Before using SD cards that have just been purchased or that have been formatted on a computer, they

must be formatted by the . Be aware that all data previously saved on the SD card will be deleted when it is formatted. Format an SD card before recording to it at 96 kHz.

85

Testing SD card performance You can test whether SD cards can be used with the .

A basic test can be done quickly, while a full test examines the entire SD card.

Conducting a quick test

1. Open MENU > SD CARD > PERFORMANCE TEST.

2. Use to select QUICK, and press .

3. Use to select YES, and press .

The card performance test will start. The test should take about 30 seconds.

The result of the test will be shown when it completes.

4. Press to stop the test.

NOTE Even if a performance test result is «OK», there is no guarantee that writing errors will not occur. This information is just to provide guidance.

86

Conducting a full test

1. Open MENU > SD CARD > PERFORMANCE TEST.

2. Use to select FULL TEST, and press .

The amount of time required will be shown.

3. Use to select YES, and press .

The result of the test will be shown when it completes.

If the access rate MAX reaches 100%, the card will fail (NG).

4. Press to stop the test.

HINT You can press to pause and resume a test.

NOTE Even if a performance test result is «OK», there is no guarantee that writing errors will not occur. This information is just to provide guidance.

87

Various settings

Setting the date and time

MENU button

Display

REC button

1. Select MENU > SYSTEM > DATE/TIME.

2. Set the date and time.

Move cursor or change value: Turn

Select item/confirm change: Press

3. Press .

The first time you turn the power on after purchase, you must set the date/ time.

88

Setting the footswitch If a footswitch (ZOOM FS01) is connected to the CONTROL IN jack, you can start/stop recorder playback

punch in/out or mute/unmute the send effect by foot.

1. Open MENU > SYSTEM > CONTROL IN.

2. Use to change the value.

Setting value Explanation

PLAY Press the footswitch to start/stop playback (equivalent to )

PUNCH I/O Use to control punching in/out (equivalent to )

SEND EFX MUTE Mute/unmute the send effect

89

Changing the sampling rate The file format used when recording to the recorder depends on this setting.

Before changing the sampling rate, must be set to OFF.

1. Confirm that is set to off.

2. Change the position.

HINT The options are 44.1 kHz, 48 kHz and 96 kHz.

NOTE When 96 kHz is selected, some unit operations are limited. The limited functions are as follows. — Recordable tracks: tracks 112 only — SEND EFX: disabled — EQ: disabled — OVER DUB: disabled — Audio interface: disabled — MONITOR OUT: output signal same as MASTER only Format an SD card before recording to it at 96 kHz.

3. Set to ON.

NOTE The sampling rate cannot be changed during operation. If a project is loaded that has a different sampling rate than the unit setting, recording and playback will

not be possible.

90

Disabling the automatic power saving function The power will automatically turn off if the is unused for 10 hours.

If you want the power to stay on always, disable the automatic power saving function

1. While pressing and holding , set to ON.

2. Use to select OFF, and press .

NOTE This setting is saved in the unit.

Adjusting the display contrast

1. Open MENU > SYSTEM > DISPLAY CONTRAST.

2. Use to select YES, and press .

HINT This can be set from 1 to 10.

91

Restoring settings to factory defaults You can restore an to its factory default settings.

1. Open MENU > SYSTEM > FACTORY RESET.

2. Use to select YES, and press .

NOTE This does not reset mixer settings. ( Resetting mixer settings)

Checking the firmware versions The firmware versions can be viewed.

1. Open MENU > SYSTEM > FIRMWARE VERSION.

This shows the firmware versions.

92

Updating the firmware The firmware can be updated to the latest versions.

1. Copy the file for updating the firmware to the root directory on an SD card.

NOTE An update file for the latest version can be downloaded from the ZOOM website (www.zoom.co.jp).

2. Insert the SD card into the .

3. While pressing and holding , set to ON.

4. press .

NOTE Do not turn the power off or remove the SD card during a firmware update. Doing so could cause the

to become unstartable.

5. After the firmware update completes, turn the off.

93

Troubleshooting

General

There is no sound or output is very quiet

Check the speaker connections and volume settings on the speakers.

Check instrument and mic connections

When using a condenser mic, turn on.

Confirm that the SIG indicators are lit green.

Confirm that is unlit.

Raise all the channel faders and the master fader, and confirm that the level meters are lit.

Confirm that the MASTER is unlit or is lit red.

Recorded audio is too loud, too quiet or silent

Adjust input gains and confirm that SIG indicators are lit green.

When using a condenser mic, turn on.

When recording to an SD card, confirm that is lit red.

Recording not possible

When recording to an SD card, confirm that is lit red.

Confirm that the SD card has open space.

When recording to an SD card, confirm that the project is not protected (to prevent overwriting).

Playback sound cannot be heard or is quiet

When playing data from an SD card, confirm that is lit green.

Raise the faders on the playback channels, and confirm that the level meters are lit.

The sounds of devices connected to input jacks are distort- ed

Confirm that SIG indicators are not lighting red. If they are lighting, lower their input gains. You can also

turn on.

Confirm that level meters are not lighting to their highest levels. If a level meter is lighting to its highest

level, lower its fader.

94

The send effect is not working

Confirm that the EFX RETURN is unlit.

Raise the EFX RETURN fader, and confirm that the EFX RETURN level meters are lit.

Confirm the send amounts of the channels on which you want to use the effect.

There is no sound or output is very quiet from MONITOR OUT AE

Confirm the mixes of each output.

Confirm that the output volume of each output is raised (MONITOR OUT A PHONES and MONITOR OUT

AE knobs).

Confirm the settings of the MONITOR OUT AE switches.

Audio interface

Cannot select or use the device

Confirm that the is connected to the computer correctly.

Confirm that is set to OFF on the .

Quit all the software that is using the , and turn the off and on again.

Reinstall the driver.

Connect the directly to a USB port on the computer. Do not connect it through a USB hub.

Sound skips during playback or recording

If you can adjust the audio buffer size of the software that you are using, increase the buffer size.

Connect the directly to a USB port on the computer. Do not connect it through a USB hub.

Turn the automatic sleep function and other computer power saving settings off.

Cannot play or record

Confirm that the is connected to the computer correctly.

Confirm that the Sound setting of the computer you are using is set to «ZOOM L-12».

Confirm that is set for input and output in the software that you are using.

Confirm that the , is lit red and the level meters are lit for channels 9/10 or 11/12.

Quit all the software that is using the , and disconnect and reconnect the USB cable connected to

the .

95

Specifications Number of input and output channels

Inputs Mono (MIC/LINE) 8 Stereo (LINE) 2

Outputs MASTER OUT 1 MONITOR OUT 5

Inputs Mono (MIC/LINE)

Type XLR/TRS combo jacks (XLR: 2 HOT, TRS: TIP HOT) Input gain PAD OFF: +16 +60 dB

PAD ON: 10 +34 dB Hi-Z ON: +6 +50 dB

Input impedance XLR: 3 k TRS: 10 k/1 M (when Hi-Z ON)

Maximum input level PAD OFF: 0 dBu (at 0 dBFS) PAD ON: +26 dBu (at 0 dBFS)

Phantom power +48 V Stereo (LINE) Type TS phone/RCA pin (unbalanced) jacks

Maximum input level +10 dBu Outputs MASTER OUT Type XLR jacks (balanced)

Maximum output level +14.5 dBu Output impedance 100

MONITOR OUT A (TRS)

Type TRS phone jacks (balanced) Maximum output level +14.5 dBu Output impedance 100

MONITOR OUT AE (PHONES)

Type Standard stereo phone jacks Maximum output level 42 mW + 42 mW @60 ohm Output impedance 100

Buses MASTER 1 MONITOR 5 SEND EFX 1

Channel strip COMP LOW CUT 75 Hz, 12 dB/OCT EQ HIGH: 10 kHz, 15 dB, shelving

MID: 100 Hz8 kHz, 15 dB, peaking LOW: 100 Hz, 15 dB, shelving

Level meters 12 segments Send effects 16 types Recorder Maximum simultaneous

recording tracks 14@44.1/48 kHz 12@96 kHz

Maximum simultaneous playback tracks

12

Recording format WAV 44.1/48/96 kHz, 16/24-bit, mono/stereo WAV format

Recording media 16 MB2 GB SD cards, 4 GB32 GB SDHC cards, 64 GB512 GB SDXC cards

Audio interface 44.1/48 kHz Recording: 14 channels Playback: 4 channels

Bit depth 24-bit Interface USB2.0

Card reader Class Mass storage USB 2.0 High Speed

USB HOST Class USB2.0 High Speed Sampling rate 44.1/48/96 kHz Frequency characteristics Frequency characteristics (44.1 kHz): -1.0 dB: 20 Hz 20 kHz

Frequency characteristics (96 kHz): -3.0 dB: 20 Hz 40 kHz Equivalent input noise Actual measurements: -128 dB EIN (IHF-A) with

+60 dB/150 input Display LCD with backlight (12864 resolution) Power supply AD-19 AC adapter (DC12 V/2 A) Power consumption 17 W maximum External dimensions 445 mm (W)282 mm (D)70.5 mm (H) Weight (main unit only) 2.53 kg

96

Send effects specifications

No Type Explanation Parameters 1 Parameters 2 tempo

synchronization

1 Hall 1 Hall reverb with a bright tone TONE DECAY

2 Hall 2 Hall reverb with a long time for early reflections TONE DECAY

3 Room 1 Room reverb with coarse reflections TONE DECAY

4 Room 2 Dense room reverb TONE DECAY

5 Plate Plate reverb simulation TONE DECAY

6 Church Reverb that simulates the sound of a church TONE DECAY

7 DrumAmb Reverb that adds a natural ambience (air sound) to drums

TONE DECAY

8 GateRev Special reverb suited to percussive performances TONE DECAY

9 Spring Spring reverb simulation TONE DECAY

10 Delay Digital delay with a clear tone TIME FEEDBACK

11 Analog Warm analog delay simulation TIME FEEDBACK

12 P-P Dly Effect that outputs delay sound alternately left and right

TIME FEEDBACK

13 Vocal 1 Very useful effect that combines delay with hall re- verb

TIME DECAY

14 Vocal 2 Effect that combines delay with mono output re- verb

TIME DECAY

15 Vocal 3 Effect that combines delay suitable for ballads with plate reverb

TIME DECAY

16 Vocal 4 Effect that combines delay suitable for rock with room reverb

TIME DECAY

Note: Delay effects that are tempo synchronized can be synchronized to the project tempo. To synchronize them, press the TEMPO button and set the tempo. Quarter notes will be synchronized to the

tempo.

97

Mixer block diagram

+4 8V

IN PU

T 1-

8

G AI

N A/

D DC

C UT

CO M

P

MONITOR OUT A_L

MONITOR OUT B_L

MONITOR OUT C_L

MONITOR OUT D_L

EFX MASTER_L MASTER_R

LE VE

L M

ET ER

PA N

RE C/

PL AY

M AS

TE R

O U

T L

M AS

TE R

O U

T R

MO NI

TO R O

UT B

PH ON

ES

MO NI

TO R O

UT C

PH ON

ES

MO NI

TO R O

UT D

PH ON

ES

PA D

-2 6d

B (IN

PU T

1, 2)

LE VE

L M

ET ER

BA LA

N C

E

A/ D

DC C

UT

VO LU

M E

FA D

ER M

O D

E

IN PU

T 9/

10 1

1/ 12

O U

TP U

T

EF X

EF X

RE TU

RN

D /A

US B S

EN D

DA TA

1- 8 t

o P C

RE C D

AT A 9

/1 1 t

o S D

CA RD US B S

EN D

DA TA

9/ 11

to PC

RE C D

AT A 1

0/ 12

to SD

CA RD

US B S

EN D

DA TA

10 /1

2 t o P

C

A

MONITOR OUT E_L

SE N

D E

FX

MONITOR OUT A_R

MONITOR OUT B_R

MONITOR OUT C_R

MONITOR OUT D_R

MONITOR OUT E_R

SE N

D E

FX

MO NI

TO R O

UT E

PH ON

ES

MO NI

TO R O

UT A

PH ON

ES

M O

N IT

O R

O U

T A

L M

O N

IT O

R O

U T

A R

D /A

D /A

D /A

D /A

D /A

Bu ilt

-in M

ic

SLATE

EQ

SL AT

E

SL AT

E

U SB

M AS

TE R

PL AY

M et

ro no

m e

G AI

N A/

D LE

VE L

PLA Y D

AT A M

AS TE

R L fro

m SD

CA RD

FA D

ER M

O D

E

M U

TE

M U

TE

M U

TE

SL AT

E

M U

TE EF

X RE

TU RN

FA D

ER

VO LU

M E

RE C/

PL AY

M AS

TE R

FA D

ER

LO W

CU T

LO W

CU T

Hi -Z

(IN PU

T 3-

SI G

PLA Y D

AT A

1-8 fro

m SD

CA RD

RE C

DA TA

1- 8 t

o SD

C AR

D

B C D E

FA D

ER M

AS TE

R

PLA Y D

AT A M

AS TE

R R fro

m SD

CA RD

LE VE

L M

ET ER

RE C D

AT A

MA ST

ER L

to SD

C AR

D RE

C D AT

A MA

ST ER

R to

SD C

AR D

M AS

TE R

A — E

M O

N IT

O R

O UT

US B R

ET UR

N DA

TA 1/

3 f rom

PC US

B R ET

UR N

DA TA

2/ 4 f

rom PC

PL AY

D AT

A 9/

11 fro

m SD

CA RD

PL AY

D AT

A 10

/1 2 f

rom SD

CA RD

SI G

EQ

FA D

ER

A B C D E

M AS

TE R

LE VE

L M

ET ER

HIGH FREQ MID LOW

HIGH FREQ MID LOW

98

ZOOM CORPORATION 4-4-3 Kanda-surugadai, Chiyoda-ku, Tokyo 101-0062 Japan

http://www.zoom.co.jp Z2I-3047-02